Search

This paper deals with a slat chain conveyor for the transport of rock materials in very severe abrasive conditions. An actual case from practice is discussed and analysed. To clarify the fatigue damage of the chain link material, the finite element method (FEM) is applied. For the experimentally recorded cycle of chain loading, numerical analysis has been performed and data for the damage of the link material are presented. Fatigue analysis is performed by ANSYS nCode DesignLife under different loading cases. FEM results show, that the fatigue crack of the link starts from region with high values of the stresses, established by experiment. [ABSTRACT FROM AUTHOR]

A finite element analysis on crash box of an automotive bumper system is presented in the paper to investigate the energy absorption of the component with and without foam-filled steel sheet metal tubes of different thicknesses for crashing or low-velocity impact analysis. The energy absorption capacity of the crash box for crashing is evaluated for different design changes of the foams-tube structure and compared the results without foam. By changing the different foam materials, various designs are proposed and simulated for maximum energy absorption. Altair Hyperworks is used for preprocessing and post-processing and Radios solver is used to run the analysis. A reasonable agreement is obtained in the results of the analytical and numerical methods. The results indicate that the energy absorption of a foam-filled crash box structure is superior to the crash box without foam. [ABSTRACT FROM AUTHOR]

The following paper aims to provide a detailed analysis of the effect of different cutting speeds in the face milling of AISI 1045 steel using coated tool. Simulations would aid in solving problems associated with experiments, leading to reduced costs and risks. DEFORM 3D is a commercially used simulation software capable of implementing machining simulations using the theory of finite element modelling. A conventional DEFORM 3D milling model has been prepared for the analysis of cutting forces and chip formation and the simulation has been carried out for two conditions. The temperature and force parameters were analyzed after carrying out the experiment and simulation under the influence of different machining and environmental conditions. The results of the simulation revealed that the predicted values of FEA possess good accuracy. [ABSTRACT FROM AUTHOR]

Steel coupling beam is a substantial member in hybrid coupled walls system that greatly enhance the strength and the energy dissipation capacity of the system compared to coupled walls linked by convention reinforced coupling beams and diagonally reinforced coupling beams. To enhance these characteristics even more, a corrugated web may be used instead of the traditional flat web. This paper presents a numerical analysis using finite elements software (ABAQUS) to investigate the nonlinear behavior of both types of steel coupling beams (with flat web and with corrugated web). The effect of initial imperfection on the nonlinear behavior of steel coupling beams was taken into account. The results were compared with the available experimental data of steel coupling beams with the flat web. Good agreement was noticed between the experimental and the numerical results. Among the conclusions drawn in this study is that using a corrugated web as an alternative to a flat web may increase both the strength and the energy dissipation of the steel coupling beams. [ABSTRACT FROM AUTHOR]

Members of double-symmetrical open cross-sections are widely used as columns in steel structures. In many cases columns are subjected not only to axial force but also local transverse force due to effect of beams connected to the columns. It results in compression in the column web that should be verified in the structural design. Current standard for design of joints in steel structures provides basic information for verification of this joint component. The design resistance of column web in compression is given as yielding resistance or, based on relative slenderness of the web, buckling resistance which takes into account buckling and crippling of the web that are considered using reduction factor. The complex behaviour of the column web in compression is affected by number of aspects, e.g. structural solution of the joint (bolted, welded, with or without end plate), level of normal stress resulting from axial force or possible interaction with shear. The paper focuses on selected aspects influencing the resistance of the column web in transverse compression and summarizes results of advanced geometrically and materially nonlinear numerical analysis which are compared with results determined using provisions in the standards. The numerical analysis was performed using computation system based on finite element method. As it is considered that the resistance of the column web in transverse compression is influenced also by the geometric properties of the cross-section including geometry of the flange-web transition, both rolled and welded cross-sections with various values of web slenderness were selected for the analysis. Along with evaluation of the results obtained in the frame of the study, suitability of different types of numerical models for investigation of this problem is discussed. [ABSTRACT FROM AUTHOR]

Members of double-symmetrical open cross-sections are widely used as columns in steel structures. In many cases columns are subjected not only to axial force but also local transverse force due to effect of beams connected to the columns. It results in compression in the column web that should be verified in the structural design. Current standard for design of joints in steel structures provides basic information for verification of this joint component. The design resistance of column web in compression is given as yielding resistance or, based on relative slenderness of the web, buckling resistance which takes into account buckling and crippling of the web that are considered using reduction factor. The complex behaviour of the column web in compression is affected by number of aspects, e.g. structural solution of the joint (bolted, welded, with or without end plate), level of normal stress resulting from axial force or possible interaction with shear. The paper focuses on selected aspects influencing the resistance of the column web in transverse compression and summarizes results of advanced geometrically and materially nonlinear numerical analysis which are compared with results determined using provisions in the standards. The numerical analysis was performed using computation system based on finite element method. As it is considered that the resistance of the column web in transverse compression is influenced also by the geometric properties of the cross-section including geometry of the flange-web transition, both rolled and welded cross-sections with various values of web slenderness were selected for the analysis. Along with evaluation of the results obtained in the frame of the study, suitability of different types of numerical models for investigation of this problem is discussed. [ABSTRACT FROM AUTHOR]

Castellated beams are well contemporarily ascribable to their structural applications. The Castellated beams are manufactured by fragmenting hot-formed rolled section that is of I shape in then it is welded together. The numerical analysis is performed using ABAQUS software. Consequently flexural, shear behavior of Castellated beams, various size and shape of openings provided, depth of openings, usage of different kinds of stiffeners, columns with and without web openings are the attempts made up in different journal papers and he researchers. It is also found that the Finite element analysis of the beam shows better results. [ABSTRACT FROM AUTHOR]

The combination of plastic and creep analysis formulation are developed in this paper. The boundary element method and the finite element method are applied in plates in order to do the numerical analysis. This new approach is developed to combine the constitutive equation for time hardening creep and the constitutive equation for plasticity, which is based on the von Mises criterion and the Prandtl-Reuss flow. The implementation of creep strain in the formulation is achieved through domain integrals. The creep phenomenon takes place in the domain which is discretized into quadratic quadrilateral continuous and discontinuous cells. The creep analysis is applied to metals with a power law creep for the secondary creep stage. Results obtained for some models studied are compared to those published in the literature. The uncertainties in both geometric and mechanical properties are considered in order to obtain the structural response. The approach is illustrated in a plate subjected to incremental load, results show that there are high probabilities of exceeding the damage states, w, equal to 0.3, 0.6, 1.2, 1.8 and 2.4 while for values of w equal to 3.0, 3.6, 4.2, 4.8, 5.4 and 6.0 these probabilities are low. The obtained results are in good agreement and evinced that the Boundary Element Method could be a suitable tool to deal with combined nonlinear problems. [ABSTRACT FROM AUTHOR]

The main objective of the research work is to present the free vibration analysis of plates composed of one of the materials that have good performance and can be applied in many fields like buildings. Material that has such properties is Functionally Graded Material (FGM). FGM consists of a mixture of ceramics and metals through varying volume fractions, ceramic material as a heat barrier at the high-temperature side, and metal material with rigid properties and high conductivity at the low-temperature side. In this paper, the FGM plate is investigated using the finite element method. We use 3-node Triangular Mixed Interpolation of Tensorial Components (MITC3), widely used by researchers or commercial software. The MITC3 element is a triangular element that gives good performance to analyze plate problems, especially isotropic plate problems. We performed the numerical analysis to examine the performance and convergence behavior of the MITC3 FGM plate element in the case of rectangular plates with varying length to width ratios, and the results are compared with the reference solution. [ABSTRACT FROM AUTHOR]

Many soft robotic structures are developed using soft fluidic actuators, which are developed using elastomeric materials such as silicon rubber. Due to the complicated geometries and nonlinearity in the soft actuator's design, it becomes very difficult to predict their behavior analytically. Finite Element Method (FEM) analysis is a numerical technique which is utilized to predict the stress, strain, and deformation in such actuators design. In this paper, bending behavior of two soft pneumatic fingers with varying wall thickness are designed and compared. Bending angle configurations of the designed fingers are evaluated at 30 and 40 kPa of actuating pressure. The obtained results show that to achieve a bending angle of 116 degrees, finger 2 requires 40 kPa of actuating pressure whereas finger 1 requires 80 kPa. Due to low stiffness of finger 2 as compared to the finger 1, which is resulted due to thickness variation in the two designed fingers, much higher bending angle configuration can be achieved at very low pressure for the finger 2. [ABSTRACT FROM AUTHOR]