Search

Abstract: Delamination-free ultrafiltration (UF) dual layer hollow fibers have been successfully fabricated by dry jet-wet spinning technique. Two different polymers of poly(amide-imide) (PAI) and polyethersulfone (PES) were utilized as the selective layer on the outer side and the porous support layer on the inner side, respectively. The dual layer substrates were subsequently modified to develop a nanofiltration (NF)-like skin on the outer layer by polyethyleneimine (PEI) cross-linking followed by multilayer polyelectrolyte depositions. These membranes were characterized by a series of standard protocols in terms of membrane structure, permeability and salt rejection, and were applied in FO process. Experiments reveal that the dual-layer NF hollow fiber modified by polyelectrolyte cross-linking and depositions can achieve pure water permeability of 4.1l/m2.h.bar and a high rejection to MgCl2 up to 97%. In FO process, the dual-layer hollow fibers exhibited a water flux of 39 and 21lm−2 h−1 in the orientations of active layer facing draw solution and feed water, respectively, by using 0.5M MgCl2 as draw solution and de-ionized (DI) water as feed at room temperature. It suggests that the combined treatment of polyelectrolyte cross-linking and deposition is an effective way to form a NF-like selective layer for FO dual-layer hollow fiber membranes. [Copyright &y& Elsevier]

One of the big challenges for forward osmosis (FO) practical application is the lack of high performance FO membranes. In this research, we successfully fabricated a novel thin film nanocomposite (TFN) FO membrane consisting of a polyetherimide (PEI) nanofibrous substrate reinforced by functionalized multi-walled carbon nanotubes (f-CNTs) and an ultrathin polyamide rejection layer. In addition to the superior inter-connected porous structure of nanofibrous substrate, the well-distributed f-CNTs in the nanofibers increased the substrate porosity by 18% and reduced membrane's structural parameter ( S value) by 30%, and significantly improved the substrate tensile modulus by 53%. The high mechanical strength provided by the embedded f-CNTs enabled us to further increase the substrate pore size and porosity in order to mitigate the internal concentration polarization (ICP). This was demonstrated by the high performance TFN-2 FO membrane with a structural parameter of 310 μm. Its water flux at 1.0 M NaCl draw solution (DS) was as high as 61 and 33 L/m 2 h in the active layer facing draw solution (AL-DS) and active layer facing feed water (AL-FW) orientations, respectively, indicating the success of the design strategy, i.e., improved membrane mechanical strength enables a further improvement of the membrane structure to mitigate the ICP. [ABSTRACT FROM AUTHOR]

Abstract: There has been a resurgence of interest in forward osmosis (FO) as a potential means of desalination, dewatering and in pressure retarded osmosis, which Sidney Loeb was advocating over 3decades ago. This paper describes the characteristics and potential applications of a newly developed FO hollow fiber membrane, which was fabricated by interfacial polymerization on the inner surface of a polyethersulfone (PES) hollow fiber. This FO membrane presents excellent intrinsic separation properties, with a water flux of 42.6L/m2 h using 0.5M NaCl as the draw solution and DI water as the feed with the active layer facing the draw solution orientation at 23°C. The corresponding ratio of salt flux to water flux was only 0.094g/L, which is superior to all other FO membranes reported in the open literature. To evaluate different application scenarios, various NaCl solutions (500ppm (8.6mM), 1wt.% (0.17M) and 3.5wt.% (0.59M)) were used as the feed water to test the performance of the FO membrane. The membrane can achieve a water flux of 12.4L/m2 h with 3.5wt.% NaCl solution as the feed and 2M NaCl as the draw solution, suggesting it has good potential for seawater desalination. [ABSTRACT FROM AUTHOR]

Forward osmosis (FO) is an increasingly important technology that has been deemed promising for addressing the global issue of water scarcity. Rapid progress over the past decade has been marked by significant innovations in the membrane development and process design. The key idea is to develop next-generation membranes through advanced membrane fabrication methods as well as hybrid systems where the FO process can really value-add. As such, this article provides an overview of the various FO membrane designs, in particular, the thin-film composite, surface-modified, and mixed matrix and biomimetic membranes. The pros and cons of each type of membranes are discussed together with the strategies used to optimize membrane properties such as structural parameter ( S ), water permeability ( A ) and salt permeability ( B ) to achieve enhanced FO performances. Furthermore, we also discuss the roles of FO in the various hybrid systems and evaluate the potential of these hybrid systems for desalination. Lastly, we provide our perspectives, especially in the area of membrane fabrications and FO hybrid systems, to shed light on the future research directions for harnessing the true potential of FO for desalination. [ABSTRACT FROM AUTHOR]

The emerging technology of pressure retarded osmosis (PRO) has been intensely studied over the past decades due to its potential in harvesting salinity gradient energy, but membrane fouling can deteriorate the PRO performance. To mitigate membrane fouling, the outer surface of the inner-selective thin-film composite (TFC) polyetherimide (PEI) hollow fiber membrane was modified by depositing poly-(allylamine hydrochloride) (PAH) and poly acrylic acid (PAA) polyelectrolytes. The results show that the outer surface of the modified membrane had less pores exposed and was more negatively charged, which was beneficial for preventing the entrance and adsorption of the negatively charged foulants into the membrane substrate. It was further proved that the modified membrane was effective in reducing PRO fouling by organic macromolecules such as alginate and bovine serum albumin, while maintaining the mechanical properties and intrinsic separation properties well. Interestingly, after 200 ppm alginate was introduced to the feed water, the power density of the modified membrane could be maintained constant at 16.2 W·m − 2 at 15 bar while that of the non-modified membrane reduced around 17% at the end of a 300-min testing period. The results suggest that the polyelectrolytes deposition is a feasible strategy for adding anti-fouling property to PRO membranes. [ABSTRACT FROM AUTHOR]

This study investigated the fouling behavior and chemical cleaning of forward osmosis (FO) membranes for treating produced/process water (PPW) from a real gas field using thin-film composite FO hollow fiber membranes. Experiments revealed that membrane fouling occurred during the PPW treatment, which hindered the water and solute transport through the membrane. The water permeability and FO reference water flux of the membrane decreased by 22.9% and 24.8%, respectively, after fouling. Membrane surface characterization was carried out, and the results indicated the deposition and entrapment of organic species on the membrane after the PPW treatment. The efficiencies of various cleaning agents, including sodium dodecyl sulfate (SDS), ethylenediaminetetraacetic (EDTA) and NaOH, were evaluated. It was found that cleaning with SDS for 15 min is the most effective method for restoring water flux, and very stable FO performance can be obtained during batch treatment of PPW. The FO membrane can reduce the PPW volume by 50% at a relatively high average water flux of 15.6 L·m − 2 ·h − 1 in the active layer facing feed solution orientation using 1 M NaCl as draw solution (equivalent to the draw solution available in the field). This study demonstrates the great potential of FO technology for produced/process water treatment. [ABSTRACT FROM AUTHOR]

Micellar draw solutions containing either sodium dodecyl sulphate (SDS), tetraethyl ammonium bromide (TEAB), 1-Octane sulphonic acid sodium salt (1-OSA) or trimethyloctyl ammonium bromide (TMOAB) were tested in the FOMBR system. After 48 h, reverse transported draw solute concentrations with 1 M draw solution concentrations for NaCl, SDS, TEAB, TMOAB and 1-OSA reached 3.22 mg/l (55 μM), 0.012 mg/l (0.04 μM), 0.067 mg/l (0.32 μM), 0.057 mg/l (0.23 μM) and 0.062 mg/l (0.29 μM), respectively. Thus, reverse transport of surfactant solute was minimal. The toxicity of each draw solution was tested using Pseudomonas aeruginosa specie and mixed (activated) sludge. The percentage growth for P. aeruginosa at the highest tested draw solute concentration of 0.05 M was 60% for SDS and 49% for TEAB, while the other surfactants proved to be more toxic. Similar to bacterial growth, the TOC reduction was higher for P. aeruginosa when compared to the mixed sludge consortium. For membrane cleaning, 0.0005 M EDTA with 0.125 g/l NaOH (a pH of 11.6) for 0.5 h was found to be an effective cleaning strategy, along with prior- and post-cleaning of the membrane using DI water. Reuse of the regenerated draw solutes indicated that the SDS flux returned close to the original flux, while the TEAB flux reached 50% of the original. Overall, SDS and TEAB are recommended for future investigation, because of minimal reverse solute transport, low in-situ microbial toxicity, good flux recovery after membrane cleaning, and effective draw solute regeneration. [ABSTRACT FROM AUTHOR]

This paper presents studies on the interactions and effects of biomacromolecules compounds on forward osmosis (FO) membrane performance. Individual components and a combination of various organic substances such as bovine serum albumin (BSA), dextran, sodium alginate and xanthan gum were used as model feeds and tested for their influences on FO performance with the active layer of the FO hollow fiber membrane facing the feed solution (AL-FS). The interactions between foulants were examined by using fluorescence spectroscopy, rotational rheometry and laser doppler micro-electrophoresis techniques. For a system containing combined organic foulants, it was found that viscosity was not the dominant factor governing FO membrane fouling as the decrease in viscosity did not always result in less fouling. The effect of divalent cations on the FO fouling behavior was also studied by adding CaCl 2 . The presence of calcium ions has exacerbated the flux decline, this occurred particularly for any combined organic foulants containing alginate, due to intermolecular bridging among alginate molecules. It is interesting to note that combined BSA + alginate caused moderate flux decline, while BSA and alginate alone did not cause any observable water flux loss. The (BSA + alginate) fouling became more severe with the presence of calcium ions. [ABSTRACT FROM AUTHOR]

The emerging thin film composite (TFC) forward osmosis (FO) and pressure retarded osmosis (PRO) membranes generally have better separation properties compared with their cellulose triacetate (CTA) counterparts. Nevertheless, their scaling performance has been rarely reported. In the current study, the phenomenon of membrane integrity loss as a result of scaling is reported for the first time for osmotically driven membrane processes (ODMPs). The results show that the TFC membrane suffered marked flux reduction during the scaling in the active-layer-facing-feed-solution (AL-FS) orientation, accompanied with the severe damage of the membrane active layer. The membrane integrity loss is attributed to the scale formation and growth in the confined space between the membrane and the feed spacer. Compared with the CTA membrane, the TFC was more prone to scaling and membrane damage due to its unfavorable physiochemical properties (presence of Ca 2 + binding sites and ridge-and-valley roughness). Although antiscalant addition was shown to be effective for scaling control in AL-FS, it was ineffective in the active-layer-facing-draw-solution orientation. The current study reveals the critical need for scaling control in ODMP processes with respect to the membrane integrity and flux stability. The results also have far-reaching implications for FO and PRO membrane design and process operation. [ABSTRACT FROM AUTHOR]

Produced water management is one of the key challenges faced by the oil and gas industry globally. Specifically, the gas industry in Qatar is challenged to minimize the produced/process water (PPW) volumes injected into disposal wells to ensure long term sustainability of the reservoirs. This research evaluated a novel application of forward osmosis (FO) to reduce the volumes of PPW disposed of by deep well injection using brine from thermal desalination plants or seawater as draw solutions. In the case of brines, this process also provides some environmentally beneficial dilution before discharge. In order to verify the PPW volume reduction concept, bench-scale FO experiments were carried out using commercial flat sheet membranes. FO performance was evaluated using PPW with and without pretreatment and results confirm that pretreatment is key to the successful implementation of FO for the treatment of PPW. Experimental results indicate that FO is effective in achieving 50% volume reduction of pretreated PPW with stable flux of 12 LMH. Lab analyses show that the TOC in the diluted draw solution was below the detection limit indicating that the TOC from the feed did not appear in the draw solution and hence would not be discharged to the environment. [ABSTRACT FROM AUTHOR]

Internal concentration polarization (ICP) in a dense support layer is one of the main reasons holding back forward osmosis (FO) process. In this regard, a highly porous microstructured support (HPμS) featuring a quasi-sponge-free sublayer pore structure can be considered a suitable alternative to develop high-performance FO membranes. However, it has not been tested for its effects on FO. This study demonstrates that a TFC membrane prepared using the HPμS works out for FO by inducing 3.35 times higher water flux without compromising a reverse salt flux (J s) compared to a control TFC membrane prepared without support adjustment. The performance improvement could be achieved by HPμS's almost no sponge-like region and lateral walls, which were desirable to minimize ICP. Furthermore, we verified that it is possible to leverage co-solvent assisted interfacial polymerization (CAIP) to further improve FO membrane performances by creating a more permeable active layer. The in-house TFC membrane optimized by the HPμS and CAIP displayed 5.3 times higher FO water flux than the control membrane, while keeping comparable J s. We expect that this research could contribute to kicking the FO membrane performance up a notch by providing a practical example of simultaneous optimization of both support and active layers. [Display omitted] • A highly porous microstructured support (HPμS) successfully reduced ICP in FO. • Almost no sponge-like region and lateral walls of the HPμS were key in reducing ICP. • A sublayer structure of a support layer was examined by a non-destructive inspection. • Co-solvent assisted interfacial polymerization further improved FO performances. • The simultaneous optimizations of support and active layers maximized FO performances. [ABSTRACT FROM AUTHOR]

In this paper, the viability of using micellar draw solutions (DS) for Forward Osmosis (FO) is presented for the first time. Above the critical micelle concentration (CMC) and the Krafft temperature (Tk), the monomers in a surfactant solution aggregate to form micelles, resulting in a relatively constant osmotic pressure above the CMC. These properties can be useful for a FO system in order to maintain a constant water flux and to enable draw solution regeneration at low energy. Three cationic and two anionic surfactants were studied at different concentrations as potential draw solutions for FO applications. Both flat sheet and hollow fiber FO membranes were used in the study. The study revealed that the micellar solutions generated more stable flux compared to other inorganic DS; the hypothesis of a constant flux above the CMC was valid only for concentrations slightly above the CMC, and micellar solutions behaved similar to inorganic solutes at concentrations significantly higher than the CMC. It was shown that external concentration polarization (ECP) does not have a significant effect in micellar solutions just above the CMC. Furthermore, all surfactants demonstrated between 3 and 300 times less reverse transport compared to NaCl at similar concentrations. Finally, the surfactant solute could be regenerated with recoveries as high as between 95% and 99%. It was thus verified that micellar solutions are an attractive DS for application to Forward Osmosis and potentially in the forward osmosis membrane bioreactor (FO-MBR). [ABSTRACT FROM AUTHOR]

Abstract: Forward osmosis (FO) has attracted wide interest for its many potential applications. Recent developments suggest that double-skinned FO membranes may perform superiorly over conventional single-skinned ones. In this design, a dense rejection skin facing the draw solution is responsible for the separation, while a second skin facing the feed solution is designed to prevent foulants entering into the porous support layer sandwiched between the two skins. For the first time, an analytical model is developed for double-skinned FO membranes and is verified experimentally. Model simulations suggest that an optimal double-skinned membrane shall have a feed skin similar to that of a low rejection nanofiltration membrane to minimize the overall hydraulic resistant and to reduce internal concentration polarization. On the other hand, the optimization of the draw skin calls for a compromise between its water permeability and solute rejection. FO water flux is greater for support layers with higher mass transfer coefficients. In addition, it decreases with decreasing draw solution concentration and increasing feed solution concentration. While membrane orientation plays an important role for applications with low feed solution concentrations (with the denser skin preferentially facing the draw solution), this effect becomes negligible at high feed solution concentrations. [Copyright &y& Elsevier]

Thin-film composite (TFC) membranes are generally preferred over integrally skinned asymmetric (ISA) membranes in pressure retarded osmosis (PRO) process due to their much higher water permeability, but they cannot operate in the active layer facing feed solution (AL-FS) orientation because of potential delamination of the rejection layer under the high applied pressure. However, operating under AL-FS orientation is preferred as a strategy for better fouling control. Hence, in this study, three ISA hollow fiber membranes were fabricated using a dry-jet wet-spinning method, followed by chemical cross-linking to obtain membranes for PRO application. The best-performing membrane was subjected to fouling test in two orientations. Our results demonstrate that the AL-FS orientation is better for a sustainable long-term PRO operation, given the stable performance throughout the two-day testing. Also, the current use of power density per membrane area as a performance benchmark may not be practical for large-scale PRO operation, and the volumetric power density per module is more relevant. In terms of volumetric power density for a hypothetical 5-in. module, our best-performing membrane is predicted to generate a 3.6 to 10 times better power density than commercial modules, rendering our ISA hollow fiber membranes promising for scaling-up to bigger modules. [Display omitted] • Operating under AL-FS orientation is preferred as a strategy for better fouling control. • Integrally skinned asymmetric hollow fiber membranes were developed for AL-FS orientation in PRO. • The membranes achieved sustainable power production when wastewater was employed. • The volumetric power density was predicted to yield promising solution for practical application. [ABSTRACT FROM AUTHOR]

Thin-film composite (TFC) membranes are generally preferred over integrally skinned asymmetric (ISA) membranes in pressure retarded osmosis (PRO) process due to their much higher water permeability, but they cannot operate in the active layer facing feed solution (AL-FS) orientation because of potential delamination of the rejection layer under the high applied pressure. However, operating under AL-FS orientation is preferred as a strategy for better fouling control. Hence, in this study, three ISA hollow fiber membranes were fabricated using a dry-jet wet-spinning method, followed by chemical cross-linking to obtain membranes for PRO application. The best-performing membrane was subjected to fouling test in two orientations. Our results demonstrate that the AL-FS orientation is better for a sustainable long-term PRO operation, given the stable performance throughout the two-day testing. Also, the current use of power density per membrane area as a performance benchmark may not be practical for large-scale PRO operation, and the volumetric power density per module is more relevant. In terms of volumetric power density for a hypothetical 5-in. module, our best-performing membrane is predicted to generate a 3.6 to 10 times better power density than commercial modules, rendering our ISA hollow fiber membranes promising for scaling-up to bigger modules. [Display omitted] • Operating under AL-FS orientation is preferred as a strategy for better fouling control. • Integrally skinned asymmetric hollow fiber membranes were developed for AL-FS orientation in PRO. • The membranes achieved sustainable power production when wastewater was employed. • The volumetric power density was predicted to yield promising solution for practical application. [ABSTRACT FROM AUTHOR]

Membrane compaction is commonly observed in polymeric membranes when subjected to elevated hydraulic pressure, but was rarely discussed in forward osmosis (FO) processes, since there was usually little hydraulic pressure difference across the membrane. In the current study, three TFC membranes were fabricated using hollow fiber substrates with varied water permeability to study the effect of the osmotic pressure on the TFC membranes. The TFC membranes were continuously tested in FO experiments for 24 h by using DI water as feed and NaCl solutions of different concentrations as draw solution, and their performances were checked again using fresh feed solutions. At the end of FO experiments, all TFC membranes experienced water flux and salt flux decline to different extents. The TFC membranes were characterized using SEM, TEM and AFM. Visible changes in the cross-section morphology and surface topography of the TFC membranes were observed after FO experiments. The observation suggested that the occurrence of membrane compaction could be associated with "negative pressure" build-up within the support layer of the TFC membranes. The current study could shed light on the important factors that should be considered during membrane fabrication and when establishing the testing protocols for the characterization of FO membrane. Unlabelled Image • The effect of the osmotic pressure on the TFC membrane structure during FO process was studied. • Three hollow fiber substrates with substantially different water permeability values were fabricated for the investigation. • FO tests with AL-DS configuration for 24 h continuously were conducted and membrane autopsy was performed. • All TFC membranes experienced irreversible water flux and salt flux decline in different extents. • The deformation in the polyamide layer and the support layer implied substantial internal stress build-up in the FO tests. [ABSTRACT FROM AUTHOR]