Search

The technique of refracturing is an effective method to solve the rapid decline in oil well production caused by factors such as severe reservoir energy loss and fracture failure after the initial hydraulic fracturing of low-permeability reservoirs. The key to designing refracturing lies in establishing a model for evaluating the potential fracturing layers. Based on the geological characteristics of the low-permeability conglomerate reservoir in the Lower Wuerhe area of the Eig District of the Xinjiang Oilfield, this paper studies the influence of different development approaches on the distribution pattern of remaining oil in the reservoir. A coupled model of remaining oil distribution and the in situ stress field is established and discusses the characteristics of the four-dimensional in situ stress field under different development modes. This paper analyzes the influence of geological factors and well network factors on the distribution of residual oil, and analyzes the influence of various factors, such as reservoir properties and injection and extraction parameters, on ground stress. Based on the residual oil distribution and ground stress changes, an evaluation method for screening potential fractured layers in reservoirs with different development modes (water injection development and depletion development) is developed. [ABSTRACT FROM AUTHOR]

The output power of PV systems is influenced by various factors, resulting in strong volatility and randomness, which makes it difficult to forecast. Therefore, this paper proposes an Informer prediction model based on optimised VMD for predicting short-term PV power. Firstly, the temporal coding of the Informer model is improved and, secondly, the original sequence is decomposed into multiple modal components using VMD, and then optimisation of the results of VMD in conjunction with the optimisation strategy of SSA improves the characteristics of the time series data. Finally, the refined data are fed into the Informer framework for modelling and prediction, utilising the self-attention mechanism and multiscale feature fusion of Informer to precisely forecast PV power. The power of PV prediction data from the SSA-VMD-Informer model and four other commonly used models is compared. Experimental results indicate that the SSA-VMD-Informer model performs exceptionally well in short-term PV power prediction, achieving higher accuracy than traditional methods. As an example, the results of predicting the PV power on 24 April in a region of Xinjiang are 1.3882 for RMSE, 0.8310 for MSE, 1.14 for SDE, and 0.9944 for R2. [ABSTRACT FROM AUTHOR]

Oil shale, as a vast potential resource, is considered an important alternative energy source, and its effective development and economic utilization are of significant importance in alleviating the contradiction between energy supply and demand. Presently, the in situ conversion technology for oil shale has gained significant global attention, with numerous extraction methods undergoing active research and development. One of these methods is the in situ conversion of oil shale based on the hydration reaction of calcium-oxide-based composite material (CaO-CM). This approach harnesses the heat produced by the reaction between CaO-CM and water as a heat source for the pyrolysis of oil shale. This paper conducted experiments to assess the feasibility of temperature associated with this method. The feasibility study mainly includes two aspects: First, it is necessary to investigate whether the temperature generated by the hydration reaction of CaO-CM can meet the temperature requirements for the pyrolysis of oil shale. Through pyrolysis experiments of Xinjiang oil shale, the minimum temperature required for oil shale pyrolysis was determined to be 330 °C. High-temperature and high-pressure reaction vessels were employed to explore the temperature generated by the hydration reaction of CaO-CM. The results show that with the increase in environment pressure, environment temperature, and reaction mass, the maximum temperature generated by the hydration reaction of CaO-CM also increases (reach 455.5 °C), meeting the temperature requirements for the pyrolysis of oil shale. Second, the study evaluates whether the hydration reaction of CaO-CM can induce pyrolysis hydrocarbons of the oil shale. Through the pyrolysis experiments of oil shale based on the hydration reaction of CaO-CM, the changes in the content of pyrolysis hydrocarbons (S2) in oil shale before and after pyrolysis are measured. The results show that under 10 MPa pressure, the content of pyrolysis hydrocarbons in the oil shale decreased from 40.96 mg/g to 0.08 mg/g after pyrolysis. This confirms the feasibility of the temperature conditions for the in situ conversion of oil shale based on the hydration reaction of CaO-CM. [ABSTRACT FROM AUTHOR]

The southern Junggar Basin, Xinjiang, has abundant coalbed methane (CBM) resources. Currently, the Baiyang River development pilot test area (BYR block for short) in the Fukang east block has achieved large-scale CBM development, but the productivity characteristics and its controlling factor are still unclear. Based on the field production data of the BYR block and experimental tests, this paper summarizes the gas and water production characteristics and presents the analysis results of the geological and geochemical responses to the productivity of CBM wells. The productivity of CBM wells in the BYR block was generally characterized as medium-to-low yield. The productivity was jointly controlled by the burial depth, structure condition, thickness and number of co-production coal seams, and hydrogeological conditions. The gas production first increased and then decreased with the increase in the burial depth of the coal seam, and a burial depth between 750 and 1000 m was the most beneficial to increasing the gas production due to the good gas preservation conditions and suitable permeability and stress conditions. The total thickness of the co-production coal seams had a positive effect on the productivity of gas wells, but the productivity was also affected by the number of co-production coal seams and interlayer interference. In the BYR block, the co-production of the nos. 41 and 42 coal seams was the most favorable combination form for CBM drainage. The productivity of CBM wells had a good response to the Na+, K+ and HCO3− concentrations but a poor response to δD-H2O and δ18O-H2O. Based on the concentrations of the main ions and TDSs of the coal seam water, a productivity response index δ* was established, and there was a good positive correlation between the productivity and δ*. [ABSTRACT FROM AUTHOR]

Accurate wind power data prediction is crucial to increase wind energy usage since wind power data are characterized by uncertainty and randomness, which present significant obstacles to the scheduling of power grids. This paper proposes a hybrid model for wind power prediction based on complementary ensemble empirical mode decomposition with adaptive noise (CEEMDAN), sample entropy (SE), bidirectional long short-term memory network (BiLSTM), and Markov chain (MC). First, CEEMDAN is used to decompose the wind power series into a series of subsequences at various frequencies, and then SE is employed to reconstruct the wind power series subsequences to reduce the model's complexity. Second, the long short-term memory (LSTM) network is optimized, the BiLSTM neural network prediction method is used to predict each reconstruction component, and the results of the different component predictions are superimposed to acquire the total prediction results. Finally, MC is used to correct the model's total prediction results to increase the accuracy of the predictions. Experimental validation with measured data from wind farms in a region of Xinjiang, and computational results demonstrate that the proposed model can better fit wind power data than other prediction models and has greater prediction accuracy and generalizability for enhancing wind power prediction performance. [ABSTRACT FROM AUTHOR]

Hydrogen is receiving unprecedented momentum and is projected to meet a sizable share of the final energy demand in the future. The coupling between the hydrogen and power systems can help integrate volatile renewable energy, reduce curtailment, and realize long-term energy storage. Different coupling modes are being proposed, yet quantitative comparisons are absent. To fill this gap, this paper firstly summarizes the system composition of potential power–hydrogen coupling modes and analyzes their advantages and disadvantages. Then, a model for power–hydrogen coordinated planning optimization is proposed for quantitative analysis. Southern Xinjiang is chosen as a representative of the northwestern area in China, which has plentiful renewable resources and a relatively small local load at present, for a case study. Through result analysis, it is found that the mode of power–hydrogen coupling at the source side, either for in situ utilization or for long-distance transport via pipelines, shows better economic competitiveness. The discussion provides suggestions and a reference to policymakers for formulating infrastructure or industry plans in advance to better accommodate the rapidly developing renewable energy. [ABSTRACT FROM AUTHOR]

Multistage fracturing in horizontal well has become one of the important techniques for the efficient development of low-permeability sandstone reservoirs. In multistage hydraulic fractured horizontal wells (MHFHWs), the depth of fracturing fluid invasion into the formation is a key parameter evaluating the imbibition enhancement after fracturing. However, few studies have been conducted on the invasion depth of fracturing fluids combining experiments and mathematical models under high-pressure differences in MHFHWs. Therefore, in this work, a mathematical model with experimental validation is proposed for evaluating the fracturing fluids invasion under high pressure. We first conducted a series of displacement experiments under different pressure differences to obtain the breakthrough time and invasion velocity. All core samples are taken from the block X of Xinjiang oilfield. A mathematical model of fracturing fluid injection was then established, considering the two-dimensional filtration of fracturing fluid. Then, the calculated invasion velocity was validated against the experimental data. Afterward, the invasion depth and invasion volume were determined for this typical horizontal well. Results show that at the end of 72 min, the invasion depth reaches 1.516 m when measured by core experiments and 1.434 m when calculated by the proposed model. The total invasion volume of all fracturing stages is estimated as 21,560.05 m3 and the actual total fluid volume injected is 24,019.6 m3. The paper formed a scientific and reasonable evaluation method of fracturing fluid invasion depth during the fracturing of horizontal wells, which provides solid theoretical support for the effective evaluation of fracturing to improve oil recovery. [ABSTRACT FROM AUTHOR]

The stability of transmission tower bases is key to ensuring the safe operation of power lines. This paper proposes a joint displacement-control technique for foundation-inclined piles and prestressed foundation tie beams to address the problem of tower base displacement and durability degradation caused by environmental factors. A finite element model of an exposed-pile transmission tower conforming to the structural characteristics of the actual line tower was established based on the current situation of Tower 292 of the ±800 kV Tianzhong line in Xinjiang, China. Three different displacement-control schemes were analyzed under the combined effects of tower line load, ice-cover load, and wind load, including changing exposed pile height, changing inclined pile tilt angle, and increasing the prestressed foundation tie beam. The analysis shows that the combined displacement-control technology of foundation-inclined piles and prestressed foundation tie beams can reduce the horizontal displacement of EHV tower foundations by more than 50%, which greatly reduces safety problems caused by tower displacement and effectively improves tower durability. [ABSTRACT FROM AUTHOR]

There are large, heavy oil reserves in Block X of the Xinjiang oilfields, China. Due to its large burial depth (1300 m) and low permeability (26.0 mD), the traditional steam-injection technology cannot be used to obtain effective development benefits. This paper conducts experimental and simulation research on the feasibility and mechanism of CO 2 -energized fracturing of horizontal wells and N 2 foam huff-n-puff in deep heavy oil reservoirs with low permeability in order to further explore the appropriate production technology. The foaming volume of the foaming agent at different concentrations and the oil displacement effect of N 2 foam at different gas/liquid ratios were compared by the experiments. The results show that a high concentration of foaming agent mixed with crude oil is more conducive to increasing the foaming volume and extending the half-life, and the best foaming agent concentration is 3.0∼4.0%. The 2D micro-scale visualization experiment results show that N 2 foam has a good selective blocking effect, which increases the sweep area. The number of bubbles per unit area increases as the gas/liquid ratio increases, with 3.0∼5.0 being the optimal gas/liquid ratio. Numerical simulation results show that, when CO 2 -energized fracturing technology takes into account the advantages of fracturing and crude oil viscosity reduction by CO 2 dissolution, the phased oil recovery factor in the primary production period can reach approximately 13.7%. A solvent pre-slug with N 2 foam huff-n-puff technology is applied to improve oil recovery factor following primary production for 5∼6 years, and the final oil recovery factor can reach approximately 35.0%. The methodology formulated in this study is particularly significant for the effective development of this oil reservoir with deeply buried depth and low permeability, and would also guide the recovery of similar oil deposits. [ABSTRACT FROM AUTHOR]

Three-dimensional (3D) reservoir geological modeling is an advanced reservoir characterization method, which runs through the exploration and the development process of oil and gas fields. Reservoir geological modeling is playing an increasingly significant role in determining the distribution, internal configuration, and quality of a reservoir as well. Conventional variogram-based methods such as statistical interpolation and reservoir geological modeling have difficulty characterizing complex reservoir geometries and heterogeneous reservoir properties. Taking advantage of deep feedforward neural networks (DFNNs) in nonlinear fitting, this paper compares the reservoir geological modeling results of different methods on the basis of an existing lithofacies model and seismic data from the X area of Karamay, Xinjiang, China. Adopted reservoir geological modeling methods include conventional sequential Gaussian simulation and DFNN-based reservoir geological modeling method. The constrained data in the experiment mainly include logging data, seismic attribute data, and lithofacies model. Then, based on the facies-controlled well-seismic combined reservoir geological modeling method, this paper explores the application of multioutput DFNN and transfer learning in reservoir geological modeling. The results show that the DFNN-based reservoir geological modeling results are closer to the actual model. In DFNN-based reservoir geological modeling, the facies control effect is obvious, and the simulation results have a higher coincidence rate in a test well experiment. The feasibility of applying multioutput DFNN and transfer learning in reservoir geological modeling provides solutions for further optimization methods, such as solving small-sample problems and improving the modeling efficiency. [ABSTRACT FROM AUTHOR]

In this paper, alkyl aliphatic hydrazine, which is different from traditional polymer fluidity improver, was synthesized from aliphatic hydrazine and cetane bromide, and evaluated as a pour point and viscosity-reducer depressant for crude oil. The evaluation results showed that alkyl aliphatic hydrazone fully reduced the pour point and viscosity of crude oil with the increase of crude oil fluidity. The viscosity reduction rate of crude oil in Jinghe oilfield was 79.6%, and the pour point was reduced by about 11.3 °C. The viscosity reduction rate of crude oil in Xinjiang Oilfield was 74.7%, and the pour point was reduced by 8.0 °C. The long alkyl chain is beneficial to the eutectic of wax in crude oil, and the polar group inhibits the crystal growth, resulting in the decrease of pour point and viscosity. The waste oil is fully recycled into oilfield chemicals. [ABSTRACT FROM AUTHOR]

Single well productivity is an important index of oilfield production planning and economic evaluation. Due to fracture-vuggy reservoirs being characteristically strongly heterogeneous and having complex fluid distribution, the commonly used single well productivity prediction methods for fracture-vuggy reservoirs have many problems, such as difficulty in obtaining reservoir parameters and producing large errors in the forecast values of single well productivity. In this paper, based on the triple medium model, the Laplace transform and Duhamel principle are used to obtain the productivity equation of a single well in a fracture-vuggy reservoir. Secondly, the seismic attributes affecting the productivity of a single well are selected using the Spearman and Pearson correlation index calculation method. Finally, the selected seismic attributes are introduced into the productivity equation of the triple medium model through the interporosity flow coefficient and the elastic storativity ratio, and the undetermined coefficients under different karst backgrounds are determined using multiple nonlinear regression. From these, a new method for predicting single well productivity of fracture-vuggy reservoir is established. In order to verify the feasibility of the new method, based on the actual production data of a fracture-vuggy reservoir in Xinjiang, the new single well productivity prediction method is used to predict the productivity of 134 oil wells. The results show that the new productivity prediction method not only reduces calculation workload, but also improves the accuracy of productivity prediction, which contributes to a good foundation for future oilfield development. [ABSTRACT FROM AUTHOR]

PetroChina's Xinjiang oilfield has a large quantity of tight oil reserves and hydraulic fracturing technology has been widely used to achieve commercial production. Some parts of this tight glutenite formation are laumontite-rich and the actual productivity of the hydraulically fractured wells is less than expected. To figure out the ways that laumontite affects tight glutenite well productivity, comprehensive experimental and numerical simulation studies have been conducted to investigate the rock mechanical properties, fluid flow behaviors and the major controlling factor of productivity. Laboratory results indicate that the tight glutenite formation with higher laumontite content has higher initial porosity, permeability but lower yield strength and more severe stress sensitivity in both permeability and fracture conductivity. For laumontite-rich glutenite rocks, there are commonly three types of rock deformation during the loading process: elastic compression, shear dilation and shear enhanced compaction. Both elastic compression and shear enhanced compaction will cause the reduction on rock porosity and permeability. A fully coupled finite element model (FEM) considering stress-induced permeability evolution was introduced to simulate the production process. Permeability evolution models of three different deformation stages were presented, respectively. Simulation results showed that our model is in good agreements with the well testing data. The simulated oil production characteristics for permeability evolution coupled and uncoupled models were discussed. Results showed the strong stress-induced permeability reduction is the major factor that laumontite causing the low and quickly declining oil rates. Initial permeability has a positive effect on productivity and stress-induced fracture conductivity reduction has slight influence on productivity. The results of this paper indicate that the stress-induced permeability evolution in the oil production process must be considered to accurately evaluating reservoirs in the studied area. [ABSTRACT FROM AUTHOR]