Search

• The progresses of the Primary Heat Transfer System of the HCPB Breeding Blanket for the DEMO reactor are outlined. • The main components of Ex-Vessel PHTS has been sized to be compliant with the new In-Vessel requirements. • Results highlights that the 2017 HCPB BB PHTS has reached improved thermal-hydraulic and safety characteristics. • Further efforts are still needed to reduce PHTS pressure drops and volumes as well as to improve IHXs performance. In the frame of the activities promoted and encouraged by the EURO-fusion Power Plant Physics and Technology (PPPT) department aimed at developing the EU-DEMO fusion reactor, strong emphasis has been recently posed to the whole Balance of Plant (BoP) which represents the set of systems devoted to convert the plasma generated thermal power into electricity and to deliver it to the grid. Among these systems, a very important role is played by the Breeding Blanket (BB) Primary Heat Transfer System (PHTS) as it is responsible to extract more than 80% of the fusion plasma power. In this framework, University of Palermo, Ansaldo Nucleare and CREATE have focused their work to improve thermal-hydraulic, safety and integration features of the Ex-Vessel PHTS for the Helium-Cooled Pebble Bed (HCPB) BB concept of DEMO. Starting from the outcomes obtained in 2016 that have allowed to highlight some criticalities which needed design changes, the paper describes progress and developments of the 2017 HCPB PHTS as well as the goals which have been achieved. The results of the research activity carried out show, in fact, i) an increase of the thermal-hydraulic performances, since a reduction in both total coolant inventory and total pressure drop has been respectively reached, ii) a potential improvement of the overall safety characteristics of the system. Nevertheless a critical assessment of these key parameters reveals that some issues are still open in terms of design integration and feasibility of the whole DEMO BoP for the helium-cooled blanket option, indicating that additional efforts are required to make this technology more attractive. [ABSTRACT FROM AUTHOR]

Abstract The geometrical freedom that additive manufacturing (AM) provides enables realisation of formerly impossible design concepts for high heat flux components aimed at use in a fusion reactor. This paper demonstrates a number of these advantages using a tile-based divertor target with two examples of novel cooling geometry. To showcase the potential benefits of high temperature operation using materials newly available for AM processing, tantalum was used as the structural material. Rather than present optimised designs, these two concepts highlight features enabled by this new technology. Simple quantitative analysis shows heat transfer improvements of 25% for a multiple small pipe concept compared to single pipe designs. Finite element analysis for both designs, including a tungsten armour, also demonstrates a more uniform temperature distribution, reducing thermal stresses below elastic limits for 5 MWm−2 heat flux cases, even with 600 °C coolant. At 10 MW m−2 yield is exceeded but the expectation is further design optimisation should enhance structural integrity. Overall, there are modest gains in heat flux handling, lifetime, and thermal efficiency compared to existing concepts, but there are significant improvements in waste reduction and remote handling mass, using typically 80% less material. Moreover, integrated manifolding and careful location of coolant connection is suggested to facilitate repair and replaceability, which should also reduce risk associated with qualifying joints. [ABSTRACT FROM AUTHOR]

In the frame of the activities promoted and encouraged by the EUROfusion Power Plant Physics and Technology (PPPT) department aimed at developing the EU-DEMO fusion reactor, strong emphasis has been recently addressed to the whole Balance of Plant (BoP) which represents the set of systems devoted to convert the plasma generated thermal power into electricity and to deliver it to the grid. Among these systems, the Divertor Primary Heat Transfer Systems (PHTSs) are intended to feed coolant to the two main components of the Divertor assembly, namely the Plasma Facing Components (PFCs) and the Cassette Body (CB). Since the DEMO Divertor must withstand high heat flux loads together with a considerable neutron deposited power, very tight tolerances may be allowed to the coolant inlet conditions. Therefore, the design of reliable PHTSs is of the utmost importance towards the development of an EU-DEMO fusion reactor. Within this framework, a study has been jointly carried out by University of Palermo, Ansaldo Nucleare and CREATE to design the Ex-Vessel PHTSs of both the PFCs and the CB for a DEMO reactor equipped with a Helium Cooled Pebble Bed Breeding Blanket. The paper describes criteria and rationale followed with the aim to achieve simple PHTS designs based on the adoption of easy-to-manufacture main components avoiding too much extrapolation from the state-of-art technology. Results of preliminary thermal-hydraulic calculations carried out to size heat exchangers, pressurizers, piping and pumps are presented and critically discussed, with particular attention to those integration, safety and feasibility constraints that may deeply affect the design of such components. Finally, the evaluation of PHTS key parameters as total pumping power and coolant inventory is reported. [ABSTRACT FROM AUTHOR]