Search

In this paper, the influence of partial discharges (PD) on the subsequent dielectric properties of oil-impregnated paper (OIP) is investigated. Dielectric frequency response (DFR) of OIP is investigated at varied levels of moisture, thermal aging, temperature, oil conductivity and electrode material, to allow comparison of these influences. It is shown that PD activity inside OIP can significantly change the real and imaginary parts of permittivity of the paper layers, especially in the frequency range below 100 Hz. It is shown that even if the PD activity is concentrated on a few percent of the test sample, the real part of permittivity measured on the entire sample after a few tens of hours of PD activity can increase up to 10 times at very low frequencies (∼ 1 mHz) and the imaginary part of the permittivity can increase up to 100 times at low frequencies (∼ 1 Hz). The change of the real and imaginary parts of permittivity due to PD activity is permanent. It is very similar to the change caused by thermal aging, and somewhat similar to the change caused by moisture and higher oil conductivity. It is also shown that the dissipation factor of OIP in contact with copper and brass increases, even in the absence of PD, but contact with aluminum and stainless steel has no influence on DFR of OIP. The results suggest that the influence of PD can be significant when estimating the moisture content or the level of thermal aging of OIP with DFR method. [ABSTRACT FROM PUBLISHER]

The oil-paper insulation of valve-side windings in a high voltage direct current (HVDC) converter transformer is subjected to both complicated voltage and severe thermal stresses. Partial discharge (PD) occurring in oil-paper bounded cavities is influenced by voltage stress type as well as temperature. This paper presents PD behaviors in an oil-paper bounded gas cavity under pulsating DC voltages. The voltage across the gas cavity and PD inception voltages at different test conditions are analyzed. Influences of temperature on statistical PD distributions and parameters are also presented. A numerical model is used to interpret PD behaviors under pulsating DC voltages and various temperatures. Experimental results and theoretical statements show that the temperature exhibits a great influence on the behaviors of cavity discharge under pulsating DC voltages. Volume resistivity, gas pressure, charge decay time constant, and electron generation rate are the primary parameters influencing PD behaviors at different temperatures. [ABSTRACT FROM PUBLISHER]

The degradation of oil-impregnated paper induced by partial discharge (PD) seriously affects the life of power equipment. In order to investigate the relationship between partial discharge and the degradation of oil-impregnated paper, PD characteristics and trap parameters of the impregnated paper are measured. In this work, a cavity discharge model is adopted and samples with different degrees of polymerization (DP) are fabricated using thermally accelerated aging to simulate transformers with different lifetimes. For each sample, phase resolved partial discharge (PRPD) spectrograms are recorded for various partial discharge times. The characteristics of partial discharge are analyzed, and the trap parameters of specimens are obtained by the thermally stimulated depolarization current (TSDC) method. Following this, the microstructures of the samples are observed using a scanning electron microscope (SEM). It is found that the damaging breakdown process of oil-immersed paper can be divided into three stages: initial stage, developing stage and pre-breakdown stage. There also exist two levels of trap on the surface of oil-impregnated paper: shallow (0.10-0.59 eV) and relatively deep (0.60-0.90 eV) energy. Importantly, the thermal aging makes the trap energy deeper while electrical aging makes the trap energy shallower. [ABSTRACT FROM AUTHOR]

The iso-margin method based on the classical analytical equations is widely used in the development of extra high voltage (EHV) bushing. Therefore, its effectiveness and feasibility have been fully validated. However, with the theoretical formula, it is difficult to evaluate the influence of stray capacitance and temperature on the internal electric stress of the ultra high voltage (UHV) bushing. It?s necessary to further improve the traditional iso-margin method. Firstly, the basic principle of iso-margin method has been briefly described. After that, the E-field distribution of condenser bushing was investigated on the Finite Element Method (FEM) computing platform. Then, the mathematical model of the advanced equal margin design method was established. Furthermore, this paper presents the program flow of optimization which combines the simulation of electro-thermal coupling process and the particle swarm optimization (PSO) algorithm. The proposed methodology was applied to the design of the prototype of the UHV resin impregnated paper (RIP) oil-SF6 bushing, which realizes the uniform axial E-field distribution of the bushing condenser. Meanwhile, the partial discharge margin between adjacent foils can be equal. Moreover, the hot-spot temperature is lower than the operation limiting temperature of the RIP material. The bushing condenser was fabricated according to the optimal structure design. The prototype of bushing has passed through all the type tests. In this paper, the FEM electro-thermal coupling simulation and the advanced equal margin design method were applied to the inner insulation structure optimization of the UHV RIP oil-SF6 bushing. Meanwhile, the proposed methodology provides some theoretical guidelines for the future research and development of other types of bushing on the UHV level. [ABSTRACT FROM AUTHOR]

Heretofore, unlike HVAC transformers, there is not much experience in both insulation design guides and test methods for ultra HV converter transformers. This special insulation phenomenon is very prominent due to the complication of voltage applied on valve-side windings of converter transformers. There is a severe lack of empirical research on partial discharge in oil-paper insulation under the combined ACDC voltage. The study in this paper provides a timely research into the issues. Nine possible configurations, which intent to simulate different defects in the transformer, have been investigated. The PD inception voltages varied ratios of combined AC-DC voltages were conducted. The discharge magnitude and its relation with the applied voltage for selected four common configurations were obtained during voltage increasing and decreasing respectively, which presented the PD initiating process and also reflected the insulation behavior of dielectrics. Besides, the Finite Element Analysis Soft was used to propose the effect of morphology of electrode surface (3 dimensional roughness is approximately 0.03 mm) on PD characteristics, which is very lacking in the previous references. The roles of DC and AC component in PD characteristics were discussed in the context of the relevant work in literatures. [ABSTRACT FROM AUTHOR]