Search

This paper presents a new single-source three-phase seven-level inverter with an inherent three-time voltage boosting capability for medium-voltage applications. The proposed topology is comprised of series connection of two switched-capacitor (SC) networks with an added half-bridge module per phase. Each of such integrated SC networks requires a single capacitor associated with three active power switches. The three-time voltage boosting feature of the proposed topology can reduce the dc-link voltage requirements by 50% in comparison to the traditional neutral point clamped (NPC), flying capacitors, active NPC (ANPC), hybrid clamped ANPC, and cascaded H-bridge topologies, and 75% to advanced ANPC topologies. It can also reduce the number of required switches and capacitors as well as their voltage stresses compared to those state-of-the-art topologies reported in the literature. By integrating “n” number of added SC networks in the proposed seven-level basic topology, the number of output voltage levels can be extended to 2n+3 per phase. A finite control set model predictive control algorithm is also derived to control the converter in both the active and reactive power exchanges modes without distorting the generated grid current quality. The capacitor voltage balancing is inherent in the proposed topology, and thus, there is no need for any additional voltage balancing circuit, which further reduces the control complexity. The performance of the proposed topology and its control algorithm are validated by several measurement results. [ABSTRACT FROM AUTHOR]

This paper presents a modification of the Vienna rectifier (VR) to obtain more than three voltage levels at the DC line connection, while preserving the unity power factor at the AC grid side. The proposed unidirectional multilevel there-phase rectifier, called the “Negev rectifier”, has a reduced device count and utilizes a unique novel Time Division Multiplexed based control scheme, which makes the challenging N-level VR expansion possible. The Negev rectifier can serve as a grid interface for supplying dc voltage to multilevel inverters with 4 up to 7 voltage levels, eliminating the burden of inverter-side voltage balancing control. The Negev hardware can be constructed by two complementary topologies, making it suitable for either high current or high voltage applications. [ABSTRACT FROM AUTHOR]

Reliability of power systems can be improved by the use of voltage source inverters (VSIs) with fast dynamic control, which can handle uncertainties induced by renewable energy resources and nonlinear loads. To ensure fast-dynamic response and simplified controller design, various model predictive control (MPC) methods are investigated in this paper. In the conventional MPC design for three-level VSIs, the cost function requires an additional term to ensure the balance of the neutral-point voltage (NP-V), which however can considerably impact the main goal of the MPC. To address this issue, an enhanced MPC using virtual space vectors is proposed, which allows the use of a significantly reduced weighting factor for the term in the cost function for NP-V balancing, while retaining fast-dynamic response. Additionally, the proposed MPC leads to reduced harmonic distortion in the VSI output voltage and current. Both simulation and controller hardware-in-the-loop studies are performed to demonstrate the effectiveness of the proposed enhanced MPC in an operating microgrid under both steady-state and fast-transient conditions. [ABSTRACT FROM AUTHOR]

An enhanced DC–DC converter is proposed in this paper, based on the combination of the Cuk and SEPIC converters, which is well-suited for solar photovoltaic (PV) applications. The converter uses only one switch (which is ground-referenced, so simple gate drive circuitry may be used), yet provides dual outputs in the form of a bipolar DC bus. The bipolar output from the DC–DC converter is able to send power to the grid via any inverter with a unipolar or bipolar DC input, and leakage currents can be eliminated if the latter type is used without using lossy DC capacitors in the load current loop. The proposed converter uses integrated magnetics cores to couple the input and output inductors, which significantly reduces the input current ripple and hence greatly improves the power extracted from the solar PV system. The design methodology along with simulation, experimental waveforms, and efficiency measurements of a 4-kW DC–DC converter are presented to prove the concept of the proposed converter. Furthermore, a 1-kW inverter is also developed to demonstrate the converter's grid-connection potential. [ABSTRACT FROM AUTHOR]

This paper proposes a hybrid pulse width modulation (PWM) based field weakening control strategy for a hybrid-inverter-driven open-winding (OW) permanent magnet synchronous motor (PMSM) system. The hybrid-inverter consists of two voltage source inverters, one is connected to a dc voltage source and named as main inverter (MI), and the other is connected to a floating capacitor and called compensation inverter (CI). A novel hybrid PWM technique is proposed for the hybrid-inverter, in which a double-vector-based PWM is applied to the MI to reduce the switching frequency, and the conventional space vector PWM is applied to the CI to compensate the reactive power. Furthermore, a field weakening (FW) control strategy based on the hybrid PWM technique is proposed to better utilize the dc-link voltage and extend the operation range of the OW-PMSM system. Simulation and experimental studies are carried out to verify the high efficiency and wide speed range of the proposed strategy. [ABSTRACT FROM PUBLISHER]

As penetration of distributed generation increases, the electrical distribution networks may encounter several challenges mainly related to voltage control. The situation may deteriorate in case of a weak grid connected to an intermittent source such as photovoltaic (PV) generation. Fast varying solar irradiance can cause unacceptable voltage variations that may not be easily compensated by slow-responding utility equipment. The PV inverter can be used to control the grid voltage by injecting/absorbing reactive power. A small-signal model is derived in order to study the stability of a PV inverter exchanging reactive power with the grid. This paper also proposes a method that utilizes the available capacity of the PV inverter to support the grid voltage without violating the rating of the inverter and the maximum voltage that the inverter's switching device can withstand. The method proposed in this paper is validated using PSCAD/EMTDC simulations. [ABSTRACT FROM PUBLISHER]