Search

This paper presents a novel fault-tolerant method for active–neutral-point-clamped (ANPC) inverter using a modified carrier-based pulsewidth modulation. At a fault event, the ANPC inverter is divided into subinverters, and the modulating signal is modified to two modulating signals. The modified modulating signals are used to control the subinverters and allow continuous operation of the three-level ANPC inverter during faulty conditions even up to four open-switch faults per phase. This technique provides the fault-tolerant capability of the ANPC inverter without the need to add any additional phase legs or complex control strategies. Furthermore, the proposed technique ensures the voltage balancing of the dc-link capacitors. The performance of the proposed fault-tolerant technique is verified through simulation studies in MATLAB/Simulink under different faulty conditions. The feasibility of the proposed technique is also verified experimentally. [ABSTRACT FROM AUTHOR]

In this paper, a voltage sensorless controller is developed for a two-switch single-phase rectifier that involves power factor correction and active pulsating power buffering without electrolytic capacitors. While a two-switch rectifier normally requires four sensed signals for control, only one current sensor is required in this proposal, thereby offering advantages such as low cost, high compactness, isolation between control and power circuits, and improved reliability. While the basic operating principle follows that of a conventional voltage sensorless controller for single-switch converters, several critical design considerations are the key to the success of the implementation which is explained in detail. The feasibilities of the controller are experimentally testified with a 100-W rectifier prototype regarding both steady state and dynamic performance. [ABSTRACT FROM AUTHOR]

The aim of this paper is to propose a novel switching control method to improve the efficiency of the basic half-bridge converter for the whole range of the load current. Using multimode control for this purpose, instead of modifying the structure of the converter, is proposed for the first time. Efficiency improvement is achieved by using a digital controller to select and change the control mode to the most efficient one, for each of the load sub-ranges. Control modes are prominent ones, including asymmetric, duty phase shift, pulsewidth modulation, and burst control, and are selected in turn, while the load current varies in its entire range from the full down to the no-load. The three transition points between control modes, being specific values of the load current, are analytically determined based on comparing the half-bridge converter power losses for different control modes. The digital controller compares the load current with the transition points and puts the converter in the control mode with the highest efficiency. The accuracy of the analytically determined transition points and the efficiency improvement of the proposed control method over the previous ones are investigated and approved by the experimental results. [ABSTRACT FROM AUTHOR]

It is well-known that current and radial vibration harmonic may cause resonance and will thus cause severe vibration and acoustic noise in a switched reluctance motor (SRM). However, not each order of harmonic will cause resonance. It has not been fully discussed which order of current and radial vibration harmonic is the most important. This paper proposes an analytical method to derive the most important order of current and radial vibration, which lays significant foundation for resonance reduction method. Then, influence of different switch angles on current and radial vibration is analytically derived and comprehensively discussed. Based on that, resonance can be reduced by optimal switch angle selection considering efficiency sacrifice. Both simulations and experiments on a three-phase sample SRM have verified the correctness of the analytical method and effectiveness of the optimal switch angle selection method. [ABSTRACT FROM AUTHOR]

In this paper, a new transformerless buck–boost converter based on a ZETA converter is introduced. The proposed converter has the ZETA converter advantages, such as buck–boost capability, input-to-output dc insulation, and continuous output current. The suggested converter voltage gain is higher than the classic ZETA converter. In the presented converter, only one main switch is utilized. The proposed converter offers low voltage stress of the switch; therefore, the low on-state resistance of the main switch can be selected to decrease the losses of the switch. The presented converter topology is simple; hence, the control of the converter is simple. The converter has the continuous output current. The mathematical analyses of the presented converter are given. The experimental results confirm the correctness of the analysis. [ABSTRACT FROM AUTHOR]

The ripple modulation (RM) is a technique that provides a variable output voltage by using the output voltage ripple of a switching-mode power converter. It was proposed to reproduce the communication signal of a visible light communication transmitter, thus avoiding the use of power inefficient linear power amplifiers. However, the RM has a major drawback: it has not been reported how to reproduce multicarrier modulation (MCM) schemes, which are the preferred modulation schemes due to their high performance in wireless communications. In this paper, it is demonstrated that the RM can be used to reproduce MCM schemes by considering the envelope and the instantaneous phase of the communication signal. Moreover, the control system of the power stage is described in detail, explaining how to modulate both the width and the phase of the gate signals, the calculation of the phase shift that is required for tracking the envelope, etc. [ABSTRACT FROM AUTHOR]

Circuit analysis and design criteria of a two-phase bidirectional converter with high voltage gain are presented in this paper. The operating principle of the forward or reverse mode is similar to that of the conventional buck or boost converter. Compared with the conventional converter, the switch stresses can be reduced significantly depending on the operating region of the voltage ratio in the two-phase converter. The power losses can also be reduced due to the use of low-voltage rating switches. The derivate converters are discussed to demonstrate the advantages of the proposed topology. A 200 W/1 MHz two-phase prototype converter with gallium nitride (GaN) devices is built and tested to verify the feasibility. [ABSTRACT FROM AUTHOR]

Model predictive current control (MPCC) can predict future motor behavior according to a motor model. In practice, however, motor parameters will vary at run time, and the parameter mismatch disturbances caused by the variation in motor parameters will deteriorate the MPCC performance. To suppress the parameter mismatch disturbances effectively, this paper proposes a modified MPCC with a current variation update mechanism. In contrast with the traditional current prediction equation that contains crude model parameters, the modified current prediction equation contains only measured information, taking advantage of the proposed current variation update mechanism, which can update the modified prediction equation within each sampling period. A simulation established by MATLAB software indicates that the proposed method can effectively suppress the parameter mismatch disturbances. Experiments are carried out to verify the correctness of the proposed method. [ABSTRACT FROM AUTHOR]

In this paper, a novel quasi-resonant flyback converter that mainly comprises two modules of flyback converters is proposed. A relay is connected in series to the input terminals of two transformers, and the transformer input structure is adjusted according to the input voltage to improve the conversion efficiency. In addition, a novel frequency-limiting quasi-resonant control strategy for solving the limitations of the conventional quasi-resonant control strategies is proposed, wherein the switching frequency is increased under light load conditions. Here, the current-mode pulsewidth modulation IC is used as the core controller. The operating principle and design parameters of the converter are analyzed and discussed in detail. The experimental results prove the feasibility of the proposed circuit. [ABSTRACT FROM AUTHOR]

In recent years, a number of bidirectional inductive power transfer systems (BD-IPT) suitable for wireless grid integration of electric vehicles have been developed. These developments have been fueled by the enhanced efficiency and spatial tolerance offered by BD-IPT systems. A typical BD-IPT system utilizes two synchronized full-bridge converters operating at fixed duty cycles to drive the primary and secondary magnetic couplers. However, in order to cater for a wide range of loading conditions, additional circuitry is employed at the expense of cost and power density. As an alternative solution, this paper proposes a novel power converter, named a boost active bridge (BAB), to replace the full-bridge converters. The BAB topology caters to a wide range of loading conditions without the need for any extra switching devices. A comprehensive mathematical model that predicts steady-state currents, voltages, and power transfer is presented to highlight the operating principles of the BAB technology. Experimental results obtained from a 3.5-kW prototype show a nearly constant efficiency under all loading conditions, validating the viability of the proposed BAB topology. [ABSTRACT FROM AUTHOR]

In this paper, an LLC type converter with two interleaved pulsewidth modulation (PWM) rectifiers is proposed. Compared with the conventional LLC converter, it achieves a wide voltage regulation range independent of load. In the proposed structure, each secondary-side PWM rectifier can operate individually. With the interleaving technique and shared primary-side switching network, the circuit secondary-side current stress is halved and the primary-side current stress is largely reduced. Besides, the filter capacitor requirement is reduced. Therefore, the proposed structure is a good option for medium/high power wide output range applications. The symmetrical LLC resonant tanks always operate at the resonant frequency, which marks the optimal operation point of the LLC resonant tank. Therefore, the conduction loss is effectively mitigated. In the proposed converter, zero-voltage turning-on (ZVS) of the primary-side MOSFETs can be ensured and is independent of the load. Moreover, the turning-off currents of the primary-side MOSFETs are small and are also load independent. This brings the benefits of minimized circulating current and negligible turning-off loss and no MOSFET turning-off voltage spike. The secondary-side auxiliary MOSFETs turn-on with ZVS and rectifying diodes turn-off with limited di/dt. Topological analysis and experimental results of a 1.3 kW/100 kHz prototype generating 230–440 V output from 390-V input are presented. The prototype demonstrates 97.31% peak efficiency and good performance over a wide output range. [ABSTRACT FROM AUTHOR]

In this paper, the design methodology of switched-tank converter (STC) is presented. The power loss breakdown analysis is conducted to point out the directions and paths for components optimization. It is revealed that the switching device conduction loss, printed circuit board (PCB) loss, and inductor loss become significant when output power is >150 W. Power loss of four switches is calculated and compared for switching device selection. The resonant capacitor is carefully designed to meet both current stress and ripple requirements. On the other hand, optimal design of the resonant inductors and PCB layout are fully investigated. The core loss model is provided, and different core materials are compared to minimize the core loss. Besides, a fine-tuned inductor winding structure is designed to achieve the lowest winding loss. Furthermore, PCB layout is optimized to get short loop length for each operation state. In addition to the hardware level optimization, an improved control method is proposed, in which the conduction time of switching devices is tuned to mitigate the circulating power. To verify the optimization work, a prototype of STC is built and tested. The experimental results indicate that a state-of-the-art performance of 98.71% efficiency and a 1000 W/in3 high power density is achieved. [ABSTRACT FROM AUTHOR]

This paper presents primary-side voltage regulated multitransformer quasi-resonant flyback converter (MTFC) for supplying isolated power switch drivers. The proposed topology offers distinct advantages over frequently used flyback converter possessing one high frequency transformer with isolated multiple outputs. Particularly, when a large number of separate dc supply units is required, then MTFC enables improved regular distribution of magnetic coupling between the common primary and the multiple secondary transformers’ windings providing a high degree of galvanic and electromagnetic isolation between multiple outputs. Primary side voltage regulation is based on the average output voltage estimation using auxiliary RDC circuit mounted across the primary windings. Operation principles of MTFC are enhanced with analytical study of cross regulation of multiple output voltages at unbalanced load conditions, indicating reduced voltage deviation of multiple outputs by applying the primary-side average voltage regulation. Experimental results of prototype 2-, 3-, and 6-transformer quasi-resonant flyback converters confirmed their cross regulation quality and application potential for independent multiple output supplies. [ABSTRACT FROM AUTHOR]

High-frequency (HF) signal injection is widely used in sensorless control schemes to drive interior permanent-magnet synchronous motors at low speeds, acquiring a good dynamic and a steady performance. However, the audible noise created by the injected HF signal is an obvious defect and restricts its application. In this paper, a variable frequency current injection method is proposed to reduce the noise. First, the theoretical basis of the variable frequency signal injection is analyzed and the demand from the injected signal is proposed. Second, a modified resonant controller is applied to realize the variable current injection and provide a zero steady-state control error. A linear active disturbance rejection controller that contains a resonant observer is applied to realize the q-axis current control and acquire rotor position information. Third, a sweep-frequency switching strategy is proposed to disperse harmonic energy. The energy of injected HF current is further extended by the proposed method when compared to the random switching method. Finally, the related experimental results are presented to verify the sensorless control method proposed. [ABSTRACT FROM AUTHOR]

For an LLC converter, it is difficult to realize the wide output range with conventional pulse frequency modulation control because of the limited operating frequency. This paper proposes a new hybrid control method. The proposed strategy combines the burst-mode control and phase-shift control methods for the LLC converter. The burst-mode control can regulate the output voltage from zero to its maximum value, and the phase-shift control can reduce the increased resonant current during burst-on time. By using this method, the wide output voltage range is realized with the low resonant current during burst-on time and zero-voltage switch (ZVS) for all switches. The reliability and efficiency of the converter can be improved accordingly. The burst duty ratio is regulated by the reference output voltage, and the phase-shift angle is derived when realizing ZVS for lagging-leg switches. Moreover, the resonant parameters and the maximum phase-shift angle are optimized under the constraints of current stress and ZVS condition. This method is easy to be implemented in a low-cost microcontroller because high-frequency real-time calculations are not necessary. A 1.5-kW prototype is built to verify the feasibility and validity of the proposed control method. [ABSTRACT FROM AUTHOR]

In this paper, a new high-frequency resonant boost converter is presented. Zero-voltage switching (ZVS) for the switches and zero-current switching (ZCS) for the rectifying diode are attained. The provided ZVS conditions reduce switching losses considerably, and ZCS conditions for the diode decrease voltage oscillations. Both switches are grounded which simplifies the gate-drive circuit and enhances the converter potential for high-frequency operation. All passive elements are high-frequency resonant type and thereby the converter power density is enhanced. The resonant inductor placed in front of the converter can operate in continuous conduction mode and smoothens the converter input current. Experimental results from a 160 W/500 kHz laboratory discrete prototype with an almost high-voltage conversion ratio of 100 to 300 V confirm the integrity of the proposed converter operation. [ABSTRACT FROM AUTHOR]

In this paper, an electrothermal-based junction temperature estimation model is proposed for an asymmetric half-bridge converter of a switched reluctance motor drive system. In the current chopping control mode, there exists a particularly uneven temperature distribution on converters due to not only the thermal coupling effects and dissipating boundary conditions, but also the different device losses in the same phase bridge. For the purpose of precise estimation for junction temperature, first, the power loss of converter is accurately calculated by the interpolation method with the help of Simulink and LTspice. Second, the thermal coupling effects and dissipating boundary conditions are analyzed in the three-dimensional finite-element method (FEM) model. According to the step power response extraction, a coupling impedance matrix is used to describe the nonnegligible thermal coupling effects between devices, and the complete heatsink can be decoupled into multiple subdivisions that represent the different heat dissipating boundary conditions. Then, with coupling impedances and subheatsink impedances in series, a compact RC network model can be built for junction temperature estimation. Consequently, analytical investigation in conjunction with FEM simulation and experiment measurements demonstrate the validity of the proposed model. [ABSTRACT FROM AUTHOR]

Wide bandgap semiconductors with fast switching speed capability are becoming an enabler to achieve the higher power density design. However, the further increase of switching frequency cannot continuously improve the power quality of ac-side waveforms in dc–ac/ac–dc application. The main reason is the distortion of pulsewidth modulation (PWM) voltage at switching point under high switching frequency. In general, there are two contributors causing PWM voltage distortions in bridge-based topologies. One is the deadtime, which occupies higher ratio in the small duty cycle case under high switching frequency and induces the voltage errors. The other one is the turn-off transient in the small load current or around the zero-crossing point of the ac-side current, because the relatively slow rising slope of the drain–source voltage will affect the right duty cycle. To solve this issue, this paper proposes a closed-loop modulation scheme to compensate the duty cycle distortion of PWM voltage based on one-cycle control or charge control. Compared to the traditional feedforward type of compensation, the proposed scheme does not need online calculation and instantaneous inductor current sampling, and it shows potential to be a general scheme for variety of topologies and modulations. Simulations and experiments are carried out on a 400-kHz single-phase full-bridge inverter with 400-Hz fundamental frequency to demonstrate the performance of the proposed approach. [ABSTRACT FROM AUTHOR]

To achieve high frequency and high efficiency over a wide load range, a monolithic voltage-mode dc–dc buck converter with advanced burst mode (ABM) and pulsewidth modulation (PWM) is presented in this paper. The load current is detected by estimating the currents flowing through the high-side and low-side switches, which maintains a near constant mode changing point. A counter-based scheme is used to achieve seamless and smooth transition between PWM and ABM. Both operating modes share the same control blocks, and no additional zero current detecting circuit is needed. In addition, the output stage switch size can be adjusted to reduce switching loss and improve efficiency under ultra-light load conditions. Experimental results show that the integrated 3 MHz converter achieves high efficiency from 80 to 91%, over a wide load range from 0.001 to 5 A. When the switch size is set to 1/3 of the maximum value, an additional 5% efficiency improvement at under 0.1 A load can be realized. The mode changing point is set at 0.4 A with less than 10% variation when the input voltage changes from 3 to 5 V. The load transient response is also improved significantly. [ABSTRACT FROM AUTHOR]

Low-voltage enhancement-mode gallium nitride high electron mobility transistors (eGaN HEMTs) are a kind of promising devices to realize high-efficiency and high-power-density conversion because of their fast switching speed, low conduction, and switching losses. Since the reverse conduction loss of eGaN HEMTs accounts for a large part of switching losses, it is of great importance to improve the traditional switching analytical model to predict the reverse conduction loss. In this paper, a complete and accurate switching analytical model of low-voltage eGaN HEMTs is presented, which considers the effects of low-parasitic inductances, nonlinear junction capacitances and nonlinear transconductances. The turn-on and turn-off switching processes are described in detail, and the resulting equations are solved by using mathematical software such as MATLAB to predict the switching waveforms during the switching periods. And an accurate loss calculation method based on the proposed model is proposed including the reverse conduction loss. The accuracy of the proposed model is validated by comparing the predicted switching waveforms and the efficiency of a synchronous buck converter with the experimental results, respectively. Moreover, the proposed model is compared with the traditional model, which proves the advantages of the proposed model. In the end, according to the proposed complete model, the effect of the top switch (TS) gate resistance, the TS drain-source capacitance, power loop inductance, current ripple, the bottom switch (BS) gate resistance, the BS drain-source capacitance, and dead time on the loss breakdown of the synchronous buck converter is explored and some qualitative suggestions are given to improve the conversion efficiency based on these analyzing results. [ABSTRACT FROM AUTHOR]

A multilevel dodecagonal voltage space vector generation scheme for variable-speed drive applications with single-dc-link operation requires a large value of capacitance for cascaded H-bridge (CHB) filters, when operated at lower speeds. In existing schemes, the multilevel dodecagonal structure is obtained by cascading a flying capacitor inverter with a CHB. In this paper, a new scheme has been proposed to minimize the capacitance requirement for full speed operation by creating vector redundancies using modular and equal voltage CHBs. Also, an algorithm has been developed to optimize the selection of vector redundancies among the CHBs in order to minimize the voltage ripple of the floating capacitors. The proposed algorithm considers instantaneous capacitor voltages and phase currents for optimal selection of vector redundancies. A mathematical model for capacitor voltage deviation is presented, and the effectiveness of the proposed algorithm is verified in both the simulation and the experiment. [ABSTRACT FROM AUTHOR]

This paper presents the current control design procedure of a single-phase grid-tied five-level packed U-cell inverter (PUC5) with an LCL output filter. The PUC5 inverter is used as an interface of renewable energy sources, such as solar applications. The LCL filter is calculated according to the grid-tied operation and converter ratings. An optimal controller, based on a linear quadratic regulator with integral action, is designed to inject a sinusoidal current with low harmonic distortion at unity power factor. For that design, the PUC5 inverter is modelled in the D–Q frame. The sensorless voltage control is incorporated into the switching technique to balance the PUC5 capacitor voltage and generate a five-level waveform at the output. Experimental tests are performed on a laboratory benchmark to confirm the theoretical design. The results prove the efficiency and accuracy of the adopted control strategy in a steady state and under transients of grid current, grid inductance, ac and dc voltage amplitudes. [ABSTRACT FROM AUTHOR]

This paper presents a lowpass–bandpass triplexer integrated switch using common lumped-element triple-resonance resonator (LE-TRR) technique. First, a lowpass–bandpass triplexer that has one lowpass channel (LPC) and two bandpass channels (BPCs) is designed. The proposed lowpass–bandpass triplexer design method is different from the conventional lowpass–bandpass multiplexer in which the feeding line is designed with lowpass response to combine bandpass structures to form lowpass–bandpass response. In this design, one branch of LE-TRR together with inductors and capacitors and another two branches of LE-TRR together with classical LC resonators are proposed to constitute one LPC and two BPCs, respectively. The LPC design combines the lowpass transformation method and parameters optimization, and two BPCs can be synthesized by classical coupled-resonator filter design theory. The designed lowpass–bandpass triplexer exhibits extremely compact size of ${\text{0.125}}\lambda _{{\rm{g}}} \times {\text{0.086}}\lambda _{{\rm{g}}}$ , and also has merits of low insertion loss, good return loss, wide bandwidth, and high port-to-port isolation. And then, p-i-n diodes are loaded on the lowpass–bandpass triplexer to realize a lowpass–bandpass triplexer integrated switch that combines both the triplexer and microwave switch function. One LPC and two BPCs are able to be switched on/off separately, and the lowpass–bandpass triplexer integrated switch has eight independent states in total. The off-state suppression of LPC is better than 36 dB, and the off-state suppression of two BPCs are better than 46 and 45 dB, respectively. [ABSTRACT FROM AUTHOR]

This paper presents an investigation on finite control set model predictive current control, validated experimentally with a rear axle electrical drive unit used in automotive applications. An improved problem formulation is suggested which lowers the computational turnaround time of the solver with approximately $\text{40}\%$ for an horizon length of $N=4$. Apart from the computational requirement aspects, the assessment focuses on inverter efficiency, phase current total demand distortion, and acoustic performance. The proposed solution is evaluated against a standard double proportional and integrator (PI) field-oriented current controller with pulsewidth modulation. It is shown that the proposed solution is feasible, the associated optimization problem at hand can be solved in real time, while exploiting the attractiveness of the proposed improvements. In summary, it is concluded that the inverter efficiency can be improved without deteriorating neither the phase current harmonics nor the acoustic performance. [ABSTRACT FROM AUTHOR]

For photovoltaic applications, the flyback microinverter with pseudo-dc-link is popular as a simple topology but brings large transformer turns ratio and thus large leakage inductance, which would deteriorate the converter efficiency. To solve this issue, based on the nonisolated pseudo-dc-link structure, this paper proposed a hybrid boost–flyback/flyback (BF/F) microinverter. This new topology is operated at the BF mode for the most segment of a half grid cycle and the F mode for the rest. During the BF mode, high voltage gain with low voltage stress is easily available in minimized transformer turns ratio. Besides, the leakage energy is recycled and the turn-off voltage spike of the main switch is clamped, as a result of a passive snubber inherently contained in this mode. Given that the BF mode is lack of step-down function, the F mode is developed to regulate the output voltage even for values lower than the input voltage. The operation and characteristic of the hybrid BF/F microinverter in boundary conduction mode are analyzed in detail, and the mathematical expression of reference current is derived theoretically to guarantee high power quality. Finally, a 240 W prototype was implemented to validate the theoretical analysis and the benefits of the proposed topology. [ABSTRACT FROM AUTHOR]

This paper presents a new highly integrable hybrid step-down converter that merges switched-inductor and switched-capacitor operations and significantly reduces onboard loss by using the input cable's parasitic inductance as its main inductor. This converter has the inductor placed at the input with a smaller voltage swing, leading to possible use of a smaller inductor and low-voltage rating switches that generally translate to reduced conduction losses. Analyses of converter operation and losses to reveal its original characteristics and design guidelines are presented to facilitate the components optimization. The converter architecture is verified by a proof-of-concept 15-W inductor-less lithium-ion battery charger prototype that uses a 1-m USB 3.0 cable as inductor. The converter, switched at 2 MHz from a 5-V input, experimentally achieves 89.7% peak efficiency and 6% higher efficiency at full load than a Buck converter counterpart. This high efficiency and zero onboard inductor yield a relative 45.7% onboard loss reduction at full load, promising excellent integration feasibility and superior system thermal management. [ABSTRACT FROM AUTHOR]

This paper proposes a novel isolated high step-down conversion circuit, called an integrated buck and modified push−pull (IBMPP) converter, which is able to lower the voltage level on the primary side of the ideal transformer, resulting in a lower turns-ratio and decreased leakage inductance. The IBMPP converter is able to prevent the duty cycle from operating in extremely low conditions. Furthermore, the proposed converter adopts active-clamp techniques to recycle leakage energy and to suppress voltage spikes, so that the conversion efficiency can be effectively improved. The advantages of the IBMPP converter are its simple topology, easy control mechanism (which requires only two signals with a 180-degree phase shift), high conversion ratio, low component counts for power switches, and less voltage stress on some of the switches on the high-voltage side. The operation principle, steady-state analysis, design considerations, and experimental results of the proposed IBMPP converter are presented in detail. The feasibility of the IBMPP is verified by hardware implementation. The full-load efficiency at 250 W is 81.44%, and the input and output voltages are 380 and 5 V, respectively. [ABSTRACT FROM AUTHOR]

High-frequency link matrix rectifier (HFLMR) is an isolated single-stage three-phase ac–dc converter, which originates from the three-phase matrix converter and inherits the advantages of matrix rectifier such as no dc-link components. In this paper, an HFLMR for more electric aircraft system is proposed. The proposed HFLMR consists of a three-phase input LC filter, a matrix rectifier, a high-frequency transformer, a diode bridge rectifier, and a purely capacitive output filter. The elimination of output filter inductor clamps the output rectifier device off-state voltage to the output voltage and eliminates any RC snubber across the rectifier. A novel symmetric modulation scheme based on space vector modulation is implemented to regulate the switching sequences and provide selective natural zero voltage switching and zero current switching of the devices of the matrix bridge. The proposed converter is more power-dense since it eliminates the dc-link components, output filter inductor, and lossy snubber across the output rectifier devices. A TI digital signal processor TMS320F28379D is used to process the converter signals and generate the gating logic. The proposed converter is validated on a laboratory prototype powered by 115 $V_{{rms}}$ ac with frequency of 400 Hz. The isolated dc output voltage is regulated at 270 V dc and the maximum output power is 600 W. [ABSTRACT FROM AUTHOR]

This paper proposes a model predictive control based on three voltage vectors for an interior permanent-magnet synchronous motor in a rotating reference frame. The proposed method can obtain the reference voltage vector quickly by predicting only one voltage vector during one sampling period using the characteristics of the deadbeat control. In addition, to obtain better steady-state performance, the optimal vector duration ratios can be obtained from the cost function to minimize the error between the predicted reference voltage vector and the synthesis vector by using the switching sequence relationship of a symmetrical three vector, which is different from applying a single voltage vector in the conventional finite-control-set model predictive control (FCS-MPC). To verify the proposed method, the experimental results are compared with the conventional FCS-MPC and two-vector-based MPC. [ABSTRACT FROM AUTHOR]

In this paper, a new high voltage gain step-up dc–dc converter is proposed for interfacing renewable power generation. The configuration optimally integrates both the coupled-inductor and switched-capacitor techniques to achieve an ultra-high step-up gain of voltage conversion with low voltage stress and high efficiency. It consists of a voltage boost unit, a passive clamp circuit, and a symmetrical voltage multiplier network. The structure becomes modular and extendable without adding any extra winding for ultra-high step-up voltage gain. The proposed topology not only reduces the voltage stress on the main switch but also maintains it steady for the entire duty cycle range. Furthermore, the reverse recovery issue of the diodes is alleviated through the leakage inductance of the coupled inductor. The operation principle and steady-state analysis are presented in detail. Experimental evaluation validates the claimed advantages and demonstrates a well-distributed efficiency curve and the peak of 96.70%. [ABSTRACT FROM AUTHOR]

Nanosecond pulse discharge plasma has many prospects in industrial applications, and high-voltage repetitive nanosecond pulse generators with compact design and light weight have become one of the key issues limiting its development in some applications. This paper presents a high voltage series-connected silicon carbide (SiC) metal-oxide -semiconductor field effect transistor (MOSFETs) module which can be served as the main switch in a repetitive high-voltage nanosecond pulse generator. This kind of series-connected MOSFETs module with only single external gate driver requiring very few components is very suitable for compact assembly. By analyzing the working principle, three topologies of series-connected MOSFETs module are proposed. The switching behaviors of the three different topologies with four SiC MOSFETs series-connected are compared experimentally. The variation of switching characteristics of series-connection SiC MOSFETs module with different numbers of devices are investigated. The layout is also optimized to shorten pulse front time and improve output pulse quality. Furthermore, a 10 kV SiC MOSFETs module with a turn-on transition time ∼10 ns is developed. The double pulse test result demonstrates excellent switching performances. Finally, a compact and high-voltage pulse generator composed of three 10 kV SiC MOSFETs module is tailored, with a typical rise time ∼40 ns and peak voltage of ∼30 kV. [ABSTRACT FROM AUTHOR]

In this paper, a distributed resource allocation problem is investigated based on a continuous-time algorithm in the presence of time-varying communication delays. The considered delays are allowed to take both “large” and “small” delay values in an alternating manner. The “small” delays refer to a class of delays that guarantee the exponential convergence to the optimal solution; otherwise, they are called “large” delays. The existence of “large” delays may affect the behavior of the optimal allocation solution, and the existing algorithms with delays may not be applicable to this kind of “large” delays. To address “large” delay cases, a switched algorithm is first proposed based on switching techniques, and then, such an algorithm is modeled as switched delay systems. Second, by adopting the Lyapunov functional theory, the upper bound of delays is first derived to guarantee the exponential convergence to the optimal solution under “small” delays, and then, a delay-dependent sufficient condition is obtained to ensure exponential convergence of the proposed algorithm based on some restrictions on “large” delays. Finally, we adopt an IEEE 118-bus practical example to show the effectiveness of the proposed algorithm. [ABSTRACT FROM AUTHOR]

A multilevel drive can be realized by using an open-ended machine, fed from dual two-level inverters. The topology supplied from isolated dc sources is suitable for transportation electrification. In vehicular systems, it is essential that the isolated dc sources, comprising of battery packs, should discharge uniformly and maintain balanced dc voltage at the dc-link terminal. A simple carrier-based pulsewidth modulation (PWM) technique is presented in this paper, which can effectively regulate the power drawn between the two two-level inverters while maintaining the multilevel operation of the drive. The modulation technique can balance the instantaneous state of charge of independent battery packs and dynamically equalize the power flow from the two inverters, based on drive requirement. This will enhance the reliability of the propulsion system in electric vehicles. The operation of the proposed PWM technique has been validated through detailed simulation and experimental tests. [ABSTRACT FROM AUTHOR]

Power flow control in multiterminal HVdc (MTdc) grids is essential to restrict operation within permissible limits. A current flow controller (CFC) can achieve this. In this paper, the modeling, control, and simulation of resistive, RC-circuit-based, and capacitive CFCs is carried out. CFC prototypes have been developed and an MTdc grid test-rig has been employed for experimental validation. Results show that all devices achieve an effective power flow management. The impact of CFC deployment in future MTdc grids is assessed on droop-controlled converters. A voltage compensation-based method is proposed to minimize power deviations during unscheduled line current control. A protection scheme has been assessed under faults. [ABSTRACT FROM AUTHOR]

This paper deals with the analysis of the input dc-link voltage ripple in multilevel inverter based on H-bridge and level doubling network (LDN). The LDN is basically a half-bridge fed by a floating capacitor, with voltage self-balancing capability, recalling the concept of a flying capacitor configuration. The amplitude of the LDN voltage ripple is analytically determined considering both the low-order and the switching harmonic components. In particular, peak-to-peak distributions of voltage ripples over the fundamental period are analytically determined, making possible the design of dc-link capacitor relying only on the dc-voltage ripple requirements. The case study makes reference to negligible switching ripple in the output current. It well represents either grid connection or passive load having almost sinusoidal currents. Numerical simulations carried out by MATLAB/Simulink and a complete set of experimental verifications are given to confirm the theoretical developments. [ABSTRACT FROM AUTHOR]

Control-to-output transfer function of the classical boost converter in continuous conduction mode contains a right-half-plane (RHP) zero that limits its frequency response. In this paper, to eliminate this zero and enhance the dynamic performance, a forward path for energy transfer to output within the on interval of the power switch is provided using the magnetic coupling. This approach simply eliminates the RHP zero by introducing an inductor coupled to the boost inductor, a diode, and a capacitor into the classical boost topology. In addition, the provided forward path enhances the voltage gain, which makes it possible to achieve a smaller operating duty cycle and reduced voltage stress for the power switch in applications with large voltage conversion ratios. Using this approach does not complicate the control structure, and a traditional single-loop voltage control scheme can be used to regulate the output voltage. The proposed approach is analytically examined by obtaining the averaged state-space model of the resulting converter, and a criterion to eliminate the RHP zero is presented. Experimental results from an implemented laboratory prototype for 48- to 200-V voltage conversion and 100-W nominal power are provided. [ABSTRACT FROM AUTHOR]

A novel version of the traditional space vector modulation (SVM) technique, with the integration of the rotating vectors, hereinafter referred to as expanded SVM, is introduced in this paper. Although different ways to benefit from the rotating vectors’ configuration have already been proposed in the literature, the generalization of the SVM theory to include them has not been proposed so far. The rotating vectors are grouped in rotating pairs, which are demonstrated to behave, by all practical aspects, as any other stationary vector. As a consequence, a circular modulation style is developed, which comprises increased flexibility over the traditional approach, thus improving the direct matrix converter capabilities. The new technique is used to achieve safe commutation, even though it might have been also applied to improve the switching losses as well. Besides the theoretical analysis, simulation and experimental results are shown to support the feasibility of the approach. [ABSTRACT FROM AUTHOR]

In this paper, a novel structure of switched capacitor converter (SCC) is proposed. First, the basic unit of the proposed SCC is presented. After that, a generalized structure of the proposed SCC is discussed. The presented SCC uses one dc source, several switches, diodes, and capacitors to produce multistep dc boosted output voltage. The capacitors in the SCC can be charged in trinary asymmetrical pattern. A detailed comparative study between the proposed and other recently developed SCC structures is presented. It is shown that the proposed SCC can produce an output voltage level with lower total standing voltage and lower maximum switch stress voltage as compared to most of the suggested SCC structures. Further, a switched capacitor multilevel inverter (SCMLI) based on cross-switched multilevel inverter has been developed and analyzed for symmetric and asymmetric dc source configurations. For fair comparison with the existing SCMLI structures, the overall cost of the structures is compared based on a cost function (CF). The proposed SCMLI provides lower cost function/output voltage level (CF/NL) in comparison with most of the other SCMLI structures for both symmetric and asymmetric dc source configurations. Extensive experimental studies validate the operation and performance of the proposed SCMLI structure. [ABSTRACT FROM AUTHOR]

Droop control is broadly used in dc power distribution systems, e.g., dc microgrids. Implementing droop control for switch mode power supplies requires the measurement of average current. Synchronous sampling is used in digital control systems to obtain the average of a triangular inductor waveform. However, the dead time, semiconductor turn-on and turn-off delays, and signal conditioning delays shift the sensed waveform and change the effective duty cycle, resulting in a misalignment and measurement error from the average value. This paper proposes a duty cycle weighted averaging method based on double sampling. By sampling twice per switching period and averaging the results using duty cycle as the weighting factor, the error due to waveform misalignment is theoretically eliminated. The result always equals the average value of the triangle. This method does not rely on the knowledge of circuit delays, making it easy to implement and robust to parameter variations. Simulations and experimental measurements validate the superior performance compared with conventional single and double sampling methods. The experiment on a droop-controlled dc–dc converter demonstrates a more accurate droop characteristic. [ABSTRACT FROM AUTHOR]

In precision motion systems, well-designed feedforward control can effectively compensate for the reference-induced error. Compared to iterative learning control (ILC), data-based fixed-structure feedforward control (DFFC) possesses robustness against reference variations, but results in mediocre performance in exactly repeating tasks. In this paper, a novel data-based switching feedforward control (DSFC) approach is synthesized to well balance the tradeoff between the extrapolation capabilities and servo performance. Specifically, a theoretical framework is developed for the proposed DSFC approach, where the feedforward control is switched between ILC and DFFC according to whether the successive references are repeated or not. When operating in the DFFC mode, a new iterative parameter tuning algorithm is proposed to enable the performance enhancement compared to the pre-existing DFFC and overcome the limitation of the allowable reference variations. Furthermore, an unbiased estimate method for the convolution matrix of the (process) sensitivity function is developed based on the impulse response experiment. No parametric model is required throughout the proposed DSFC procedure, and the optimal parameters of the DFFC mode can be unbiasedly estimated. Experimental results on an ultraprecision wafer stage confirm that the proposed DSFC combines advantages of ILC and DFFC, and achieves high performance for both repeating and varying tasks. [ABSTRACT FROM AUTHOR]

According to different clamping methods, nine modes (C_MODE1-9) of the traditional discontinuous pulsewidth modulation (DPWM) for neutral-point-clamped three-level converter have been revealed. Since traditional DPWM cannot balance neutral point (NP) voltage under the full range of modulation index (MI) and power factor (PF), two extended modes (E _MODEs) are proposed in this paper, which can balance NP voltage. The proposed extended discontinuous pulsewidth modulation (EDPWM) is characterized by using C_MODEs and E_MODEs alternately.Therefore, EDPWM can balance NP voltage under the full range of MI and PF. Since the switching numbers under C_MODE and E_MODE in one switching cycle are two and three, respectively, the switching loss under EDPWM is lower than that under other pulsewidth modulation (PWM) strategies. The performance of EDPWM is analyzed and compared with traditional DPWM, space vector PWM (SVPWM) and virtual SVPWM (VSVPWM) in terms of switching loss, waveform quality, and the ability of NP voltage control. Finally, the feasibility and superiority of the proposed method are verified by experiments. [ABSTRACT FROM AUTHOR]

In this paper, a resonant current-mode receiver is studied to charge low-voltage batteries wirelessly for supplying medical implantable systems. To increase efficiency, the root-mean-square (rms) current in the LC tank of the receiver (RX) is reduced by using a voltage-boosted current-mode (VBCM) receiver. This receiver combines the conventional current-mode receiver with a switched-capacitor converter to boost the voltage instantaneously at the switching node ($V_{X}$) of coil. Owing to the suggested technique, the receiver directly charges a low-voltage battery while maintaining a small rms current without using a complex voltage regulator. The receiver achieves an efficiency as high as 84.7% with a 1.1 V battery while operating at the resonant frequency ($f_{{\text{reso}}}$) of 6.78 MHz. The power delivered to the output ($P_{O}$) is in the range from 1.5 to 50 mW. The VBCM receiver was fabricated by 180 nm CMOS technology with a total active area of 0.22 mm2. [ABSTRACT FROM AUTHOR]

This paper proposes the use of an artificial neural network (ANN) for solving one of the ongoing research challenges in finite set-model predictive control (FS-MPC) of power electronics converters, i.e., the automated selection of weighting factors in cost function. The first step in this approach is to simulate a detailed converter circuit model or run experiments numerous times using different weighting factor combinations. The key performance metrics [e.g., average switching frequency ($f_{{\rm sw}}$) of the converter, total harmonic distortion, etc.] are extracted from each simulation. This data is then used to train the ANN, which serves as a surrogate model of the converter that can provide fast and accurate estimates of the performance metrics for any weighting factor combination. Consequently, any arbitrary user-defined fitness function that combines the output metrics can be defined and the weighting factor combinations that optimize the given function can be explicitly found. The proposed methodology was verified on a practical weighting factor design problem in FS-MPC regulated voltage source converter for uninterruptible power supply system. Designed weighting factors for two exemplary fitness functions turned out to be robust to load variations and to yield close to expected performance when applied both to detailed simulation model (less than 3% error) and to experimental test bed (less than 10% error). [ABSTRACT FROM AUTHOR]

Automated early detection and identification of switch faults are essential in high-voltage applications. Modular multilevel converter (MMC) is a new and promising topology for such applications. MMC is composed of many identical controlled voltage sources called modules or cells. Each cell may have one or more switches and a switch failure may occur in anyone of these cells. The steady-state normal and fault behavior of a cell voltage will also significantly vary according to the changes in the load current and the fault timing. This makes it a challenging problem to detect and identify such faults as soon as they occur. In this paper, we propose a real-time and highly accurate MMC circuit monitoring system for early fault detection and identification using adaptive one-dimensional convolutional neural networks. The proposed approach is directly applicable to the raw voltage and current data and thus eliminates the need for any feature extraction algorithm, resulting in a highly efficient and reliable system. Simulation results obtained using a four-cell, eight-switch MMC topology demonstrate that the proposed system has a high reliability to avoid any false alarm and achieves a detection probability of 0.989, and average identification probability of 0.997 in less than 100 ms. [ABSTRACT FROM AUTHOR]

This paper presents a novel switch current stress reduction technique for a single switch boost-flyback high step up dc–dc converter. Coupled inductor-based converters do not have a sufficiently higher inductance value of their windings. This creates current surge during transient and steady state, which in turn increases current stress at main switch. To compensate this difficulty in coupled inductor-based boost flyback converter, an inductor–diode parallel combination has been connected in series with the switch. This technique increases the effective inductance of the coupled inductor primary winding during switch turn-on operation and helps to reduce current stress. Steady-state operating principle with the proposed technique is analyzed in continuous conduction mode. The current reduction technique is discussed with a proper mathematical derivation. To verify theoretical findings, simulation study is carried out in MATLAB/Simulink R2014b. Finally, a laboratory-based 40-W prototype converter is designed to show the effectiveness of the proposed switch current reduction technique. [ABSTRACT FROM AUTHOR]

The efficiency of multiterminal dc (MTDC) grid simulation decreases with an expansion of its scale and the inclusion of accurate component models. Thus, the variable time-stepping scheme is proposed in this paper to expedite the electromagnetic transient computation. A number of criteria are proposed to evaluate the time-step and regulate it dynamically during simulation. Meanwhile, as the accuracy of results is heavily reliant on the switch model in the modular multilevel converter, the nonlinear behavioral model with a greater accuracy is proposed in addition to the classic ideal model, and their corresponding variable time-stepping schemes are analyzed. Circuit partitioning is effective in accelerating the MTDC grid simulation via fine-grained separation of nonlinearities. A subsequent large number of identical circuits enabled a massively parallel implementation on the graphics processing unit, which achieved a remarkable speedup over the CPU-based implementation. The inclusion of variable time-stepping schemes eventually makes the simulation of MTDC grid with highly detailed nonlinear switch models feasible. The results are validated by commercial device-level and system-level simulation tools. [ABSTRACT FROM AUTHOR]

In this paper, a new soft-switching bridgeless single-phase power factor correction converter is introduced and analyzed. Employing an auxiliary flyback circuit, existing dead angle in the input current is eliminated while softswitching is achieved. The flyback converter processes only small amount of output power. Therefore, conduction losses of its bridge diode and semiconductor devices are low. Also, the auxiliary flyback converter provides soft-switching condition for buck switches. All semiconductors are turned on and off under soft-switching condition. In addition to reduction of switching losses, diode's reverse-recovery problems are eliminated due to soft-switching condition. The proposed approach takes advantage of operating under discontinuous conduction mode to shape the input current into sinusoidal form inherently. Experimental results are reported for a 120-W prototype at 110 Vrms input and 48-V output. The results demonstrate efficiency of 93% at nominal load condition. Furthermore, the input current harmonics fulfill IEC61000-3-2 (Class D) standard as well. [ABSTRACT FROM AUTHOR]

A new transformerless bidirectional buck-boost converter is proposed in this paper. The proposed converter has a simple circuit structure, low component count, low voltage stress on the power transistors, and a wide voltage gain range. This makes it applicable in the energy storage charge/discharge systems, such as electric vehicles (EV), microgrids and nanogrids with energy storage units, and uninterruptible power supplies. In addition, synchronous rectification between the complementary transistors is employed to improve the converter efficiency. A comprehensive analysis of the steady-state operation, small-signal model, component parameters design, and efficiency analysis of the proposed converter operating in a continuous conduction mode is given. Finally, a 1.6-kW scaled-down prototype was built using Silicon Carbide MOSFETS to validate the effectiveness and feasibility of the proposed converter. [ABSTRACT FROM AUTHOR]

In this paper, a new Lyapunov-based model predictive controller is proposed for a 7-level packed U-cell (PUC7) grid-connected inverter. A cost function of the proposed model predictive controller is designed from the system stability point of view, inspired by the Lyapunov control theory. The proposed controller eliminates the need for gains that are associated with cost function coefficients, as seen in classical model predictive control based controllers. Therefore, the control design problem is significantly simplified. In addition, the average switching frequency is also reduced, as shown in both simulation and experimental results, leading to a reduction in switching losses. Simulation and experimental tests, on a PUC7 lab prototype, demonstrate the excellent performance of the proposed control system, in terms of high disturbance rejection, robustness to parameter mismatches, and fast dynamic response. Such features qualify the proposed control strategy as a good candidate for grid-tied applications. [ABSTRACT FROM AUTHOR]

In this paper, a novel noncoupled inductor high voltage gain single-ended primary-inductor converter (SEPIC) is presented. The proposed converter has various advantages, such as lower voltage stress on the switches, noninverting output voltage, high efficiency, and high voltage gain. Also, the introduced converter has a continuous input current which makes it suitable for renewable energy and fuel cell applications. Moreover, high voltage gain is achieved without using any transformer and coupled inductor, thus there is not any voltage overshoot for the switches during the turn-off process. This effect allows low conduction losses by using lower voltage rating switches and also additional clamping circuit is not needed. The control system of the presented converter is simple and the converter can be easily controlled in continuous conduction mode mode operation. Because, the gating pulses for both of the switches are the same and wide output voltage range is achieved only by changing the duty cycle. Furthermore, the number of the components compared to the other noncoupled inductor, SEPIC-based converters which provide near voltage gain to the proposed converter, is reduced. The detailed operation of the introduced converter and design considerations are discussed. Experimental results are presented to verify the performance of the proposed dc–dc converter. [ABSTRACT FROM AUTHOR]