Search

In this paper, many impedance-source inverters with coupled inductors have been investigated to obtain a high step-up boost ratio. However, the leakage inductors in these topologies induce great voltage spikes at the dc link, which will increase the voltage stress of switches. Thus, the power level of inverters is limited. Furthermore, the efficiency of the inverters can be degraded by the losses associated with leakage inductors. To address abovementioned issues, this paper proposes a family of low-spike high-efficiency Y-source inverters. The proposed inverters have the ability of eliminating voltage spikes at the dc link and recycling the leakage energy via the additional diode and capacitor. In order to show the excellent characteristics of the proposed topologies, this paper compares the performances of the proposed inverters and the improved-Y-source inverter in many aspects. Simulation and experimental results have verified the abilities of the proposed inverters. [ABSTRACT FROM AUTHOR]

This paper proposes a new dc–ac converter with a reduced number of semiconductor switches and gate drive and control circuit components. A salient feature of this inverter is its pure sinusoidal line-to-line voltages with no need for output filter. Also, the proposed inverter improves the voltage utilization factor of the input dc supply compared to the four-switch three-phase inverter (first best topology in the literature from the number of switches point of view) and standard six-switch inverter with sine pulsewidth modulation. The proposed inverter is capable of operating with a wide range of output voltages from zero to the full value of the dc input voltage by appropriately altering the instantaneous duty cycle. A three-phase universal inverter with only three power switch has been proposed in this paper for the first time ever, to our knowledge. For the purpose of providing a good compromise between fast transient response and stability, a model predictive controller is proposed. All the design expressions have been derived. A comparison with other dc–ac converters is given to show the merits of the proposed converter. Finally, satisfactory circuit operation is confirmed by experimental results from a laboratory prototype. [ABSTRACT FROM AUTHOR]

In this paper, two structures are proposed for the switched-inductor quasi-Z-source inverter. In the proposed structures to extend the voltage gain of inverter, two new switched-inductor structures are used. In the proposed structures, voltage across the capacitors in the Z-source network and in the switched-inductor is symmetric and small. The other advantage of proposed inverters is known as achieving higher voltage gain per smaller duty cycle ratio (of shoot-through). Compared with a conventional continuous input current switched-inductor quasi-Z-source inverter at the same gain voltage, there is less of a ripple of input current in the proposed inverters. In this paper, at first the both the conventional and the proposed switched-inductor Z-source inventers are thoroughly investigated to find out their governing relations. Then, the proposed Z-source inverters are compared with the conventional ones by simulating them to assess their performance efficiency. Next, applying the simple boost pulse width modulation the simulation is carried out with PSCAD/EMTDC software. After that, to evaluate the obtained results, the prototypes of the proposed inverters with 48 Vdc input voltage are used. [ABSTRACT FROM PUBLISHER]

In this paper, new half-bridge and full-bridge topologies for a switched-boost inverter are proposed. These topologies have a high boost factor in comparison with conventional types. In addition, the proposed topologies have continuous input current and can generate zero-voltage level in output. In this paper, the operation of the proposed inverters in different operating modes is analyzed. Then, the values of inductors and capacitors are designed. Moreover, the used switching pattern and its logical diagram are introduced. A comprehensive comparison between the proposed and conventional topologies in terms of the boost factor, the number of elements, and the efficiency shows the good features of the proposed inverters. Finally, to verify correct operation of the proposed topologies and derived equations, simulation and experimental results are presented. [ABSTRACT FROM AUTHOR]

In this paper, two topologies are presented for the enhanced-boost quasi-Z-source inverters (qZSI), namely continuous input current configuration and discontinuous input current configuration of enhanced-boost qZSI with two-switched impedance networks. Similar to enhanced-boost impedance-source inverters (ZSIs), these proposed inverter topologies possess very high boost voltage inversion at low shoot-through duty ratio and high modulation index to provide an improved quality output voltage. Compared to enhanced-boost ZSIs with two-switched Z-source impedance networks, these proposed inverter topologies share common ground with source and bridge inverter, overcome the starting inrush problem, and draw continuous input current and the lower voltage across the capacitors. Moreover, the input ripple current is negligible. This paper presents the operating principles and analysis of continuous input current configuration enhanced-boost qZSI with two-switched impedance networks and compares with ZSI, switched inductor ZSI, DA/CA-qZSI, and enhanced-boost ZSIs. The theoretical analysis is done and is validated through simulation and experimental results. [ABSTRACT FROM PUBLISHER]

The magnetic resonant wireless power transfer (WPT) system with a class E inverter has wide application in mid-range power transmission, especially for several megahertz scenario. However, it is cumbersome for the existing modeling and analysis methods to obtain the analytical solution to the system variables, which limits the evaluation of system characteristic. This paper proposes a nonlinear mathematical model for the WPT system with a class E inverter. The equivalent small parameter method (ESPM) is first adopted to solve the proposed six-order nonlinear model, and symbolic-form steady-state periodic solutions are yielded. During the whole solving process, only three iteration steps are needed for the proposed method. Compared with other existing modeling and analysis methods, the symbolic periodic results acquired by the ESPM exhibit sufficient accuracy by virtue of the combination of more higher harmonics. Meanwhile, the calculation complexity is simplified remarkably. Simulation and available experiments validate the effectiveness and accuracy of the proposed method. [ABSTRACT FROM AUTHOR]

In this paper, a generalized switching modification method is proposed to reduce the root-mean-square (rms) current flowing into a dc-link capacitor in a dc–dc–ac structure consisting of a boost converter and a three-phase inverter. To analyze the current flowing into the capacitor, we analyze the currents at the respective converter and inverter sides. Based on this analysis, we derive an analytical method to find the modification time between the converter and inverter pulsewidth modulation (PWM) carriers through a Fourier series and approximation to facilitate real-time implementation. Real-time implementation of the modification time calculated by the derived method is described. To verify the validity of the proposed method, experimental results are presented based on a 1-kVA dc–dc–ac prototype. The proposed method has a better capacitor rms current reduction performance than the conventional method in various inverter power factors and PWM strategies. Especially, it has an excellent performance in mid-power factor level (0.95–0.1). [ABSTRACT FROM AUTHOR]

In this paper, a new topology for half-bridge Z-source inverter is proposed. The proposed topology has only one impedance network. Unlike to the conventional half-bridge inverter, the proposed topology can provide zero voltage level at the output. It also increases output voltage level and stabilizes it in the desired value. Capacitor voltage stress in the proposed topology is low, and, therefore, nominal voltage of capacitor and cost decreases. In this paper, the steady-state analysis of the proposed inverter in two new operations which are named synchronous operation of diodes and asynchronous operation of diodes is conducted based on mathematics calculations. A method to obtain high-voltage gains by cascading the Z-network and combining middle inductors is presented that leads to cost, size, and weight reduction. Comparison among the proposed converter with conventional ones shows its excellent performance. The experimental results have good agreement with analytical analysis for the proposed topology. [ABSTRACT FROM PUBLISHER]

Due to the pulsating power at the inverter output terminals, the passive storage elements of the boost stage of the current-fed switched inverter (CFSI) contain a power frequency harmonic component (100 Hz), apart from dc and switching frequency components. In prior designs, the second harmonic component is suppressed by increasing the size of the input filter inductor and capacitor or by using additional circuits. This paper presents a complete characterization of a control-based approach to suppress the power frequency harmonic component in the input inductor current of a CFSI. It also presents a comprehensive characterization of the harmonic power redistribution. Using the proposed approach, it is demonstrated that the inductor value of a CFSI is reduced by 61% for the same peak-to-peak ripple. This leads to an improvement in the conversion ratio, efficiency, and power density of the overall converter. A SiC MOSFET-based CFSI with 75-kHz switching frequency is used to verify the proposed design philosophy. [ABSTRACT FROM AUTHOR]

Usually, the parallel-compensated inductive power transfer (IPT) topology fed by a current-source inverter is controlled through variable switching frequency and fixed 50% duty cycle method. This enables the system to operate at resonance frequency, which drifts due to load and other parameter variations. Owing to this control constraint, the load requirements are fulfilled by adding extra dc–dc chopper at the output. This paper presents a new control technique for a parallel–series/series IPT network, fed from a full-bridge current-source inverter to meet the load demand directly by an inverter. Therefore, the extra chopper stage at the output side of the converter is eliminated. The control goals are achieved through a two-loop control method, where the inner input current loop controls the source current and the outer output current loop meets the load requirements. The detailed steady-state operation, converter design, small-signal modeling, and control are reported, and experimental results obtained from a 1.6-kW lab prototype are included to verify the mathematical analysis. [ABSTRACT FROM AUTHOR]

In this paper, a three-level quasi-switched boost T-type inverter (3L qSBT2I) is proposed. A new pulse-width modulated (PWM) control method is presented to reduce the inductor current ripple of the qSBT2 I. In the introduced PWM technique, the shoot-through duty cycle is maintained constant to keep the modulation index as high as possible. Then, the only control parameters of the qSBT2I are the duty cycles of the two additional switches. By controlling the duty cycles of the two additional switches, the voltage gain of the proposed qSBT2 I can be improved to a value larger than that of the conventional 3L impedance source inverters. The steady-state analysis, operating principles, and comparisons with the impedance source-based 3L inverters are presented. A 1-kW prototype is constructed to verify the operating principle of the 3L qSBT2I. An indirect dc-link voltage regulator and a capacitor voltage-balance controller are applied to the proposed qSBT2I. Simulation and experimental results are presented. [ABSTRACT FROM AUTHOR]

This paper proposes the combination of a novel modified quasi-Z-source (MqZS) inverter with a single-phase symmetrical hybrid three-level inverter in order to boost the inverter three-level output voltage. The proposed single-phase MqZS hybrid three-level inverter provides a higher boost ability and reduces the number of inductors in the source impedance, compared with both the single-phase three-level neural-point clamped quasi-Z-source inverter and the single-phase quasi-Z-source cascaded multilevel inverter. Additionally, it can be extended to obtain the nine-level output voltage by cascading two three-level pulse width modulation switching cells with a separate MqZS and a dc source, which herein is called a single-phase MqZS cascaded hybrid five-level inverter (MqZS-CHI). A modified modulation technique based on an alternative phase opposition disposition scheme is suggested to effectively control the shoot-through state for boosting the dc-link voltage and balancing the two series capacitor voltages of the MqZS. The performances of both the proposed MqZS-CHI and the modulation techniques are verified through simulation and experimental results. [ABSTRACT FROM PUBLISHER]

In this paper, two switched-capacitor quasi-switched boost inverters (qSBIs) are proposed. By adding one capacitor and one diode to the qSBIs, the proposed inverters achieve high voltage gain with low voltage stress on active switches, capacitors, and diodes. The proposed inverters can extend to n-cell for voltage gain improvement. The operating principle, steady-state analysis, and impedance parameter selections of the proposed inverter are presented. A full comparison between the proposed inverter and other impedance-source inverters is addressed. A 500-W prototype is built to verify the operating theory of the proposed inverter in both the standalone mode and the grid-connected mode. Simulation and experimental results validate the theoretical analysis. [ABSTRACT FROM PUBLISHER]

The battery energy-stored quasi-Z-source (BES-qZS)-based photovoltaic (PV) power generation system combines advantages of the qZS inverter and the battery energy storage system. However, the second-harmonic ( \text2\omega ) power ripple degrades the system's performance and affects the system's design. An accurate model to analyze the \text2\omega ripple is very important. The existing models did not consider the battery, or assumed a symmetric qZS network with $L_{{1}}= L_{{2}}$ and $C_{{1}}= C_{{2}}$, which limits the design freedom and causes oversized impedance parameters. This paper proposes a comprehensive model for the single-phase BES-qZS-PV inverter system, where the battery is considered and there is no restriction of $L_{{1}}= L_{{2}}$ and $C_{{1}}= C_{{2}}$ . Based on the built model, a BES-qZS impedance design method is proposed to mitigate the \text2\omega ripple with asymmetric qZS network. Simulation and experimental results verify the proposed \text2\omega ripple model and impedance design method. [ABSTRACT FROM AUTHOR]

In this paper, an improved transformerless single-phase single-stage grid-tied flying inductor inverter is presented. The negative terminal of the photovoltaic (PV) array is grounded in the improved topology, which increases reliability and suppresses the leakage current. The proposed topology has buck–boost capability without increasing the number of required components and has a high efficiency. An improved control algorithm for proper operation of the proposed topology which decreases switching losses has been investigated. Moreover, a perturbation and observation maximum power point tracking (MPPT) algorithm has been adapted to the proposed inverter, which does not utilize proportional–integral (PI) controllers, for the purpose of the MPPT. Furthermore, a design procedure of the passive elements of the converter based on the corresponding operating has been demonstrated. Simulation in MATLAB Simulink plus an experimental prototype is developed to reconfirm the designed results. Finally, a comparison study has been investigated for better clarification of the advantages and disadvantages of the proposed inverter. [ABSTRACT FROM PUBLISHER]

Photovoltaic (PV) microinverters dispense with the line frequency transformer, however at the cost of system grounding and ground leakage current problems. These have been erstwhile resolved by the topologies derived from buck, boost, buck–boost, Zeta, Watkins–Johnson, and Ćuk converters, or combinations of these. The Ćuk derived inverters, employing second-order input and output filters, offer the most efficient, lightweight, and economical solution in the class. This paper presents design and detailed operation of a Ćuk derived, common-ground PV microinverter in continuous conduction mode operation. The inverter is shown to be compatible with both linear and nonlinear loads, in stand-alone and grid-connected modes of operation. Optimal design rules of passive components are rigorously derived to ensure attenuation of input voltage ripples arising from the twin effects of switching and double-frequency output power oscillation. Additionally, the design rules also incorporate considerations of efficiency maximization and some aspects of easing control complexity. Inverter performance is experimentally validated with a 300 VA, 110 V, and 50/60 Hz laboratory prototype. [ABSTRACT FROM PUBLISHER]

The Z-source inverter (ZSI) employs an LC impedance network between the main inverter bridge and the power source. The unique feature of the ZSI is that it can operate either in buck or boost mode with a wide range of obtainable output voltages from a given input voltage. This topology also exhibits better electromagnetic-interference noise immunity when compared to a traditional voltage-source inverter (VSI). However, the LC impedance network of ZSI significantly increases the size and cost of the power converter and can make it unsuitable for low-power applications. This paper proposes a novel topology called switched boost inverter (SBI) which exhibits similar advantages of ZSI with lower number of passive components and more active components compared to ZSI. The steady-state and small-signal analyses of SBI, along with its pulsewidth modulation (PWM) control strategies, have been discussed in this paper. This paper also presents a comparison of SBI and ZSI with the same input and output parameters. The theoretical analysis given in this paper has been validated using a laboratory prototype of SBI, and the experimental results are presented for verification. The experimental harmonic spectrum of the inverter's output voltage with the proposed PWM technique is also plotted and compared with that of a traditional VSI. All the experimental results show good correlation between theory and experiments. [ABSTRACT FROM PUBLISHER]

In this paper, a new topology for Z-source inverter based on switched Z-source network is proposed. The proposed switched Z-source inverter can provide high voltage gain in low duty cycles. The continuous input current is one of the other advantages of the proposed inverter. The performance of the proposed inverter is investigated in different operating modes and the voltage and current equations of all elements and equations of critical inductance are calculated. Furthermore, the power losses and efficiency analyses are presented. The comprehensive comparison between the proposed inverter and the other conventional Z-source inverters shows its excellent performance. Finally, to prove the correct operation of the proposed topology, the experimental and simulation results using PSCAD/EMTDC software are presented. [ABSTRACT FROM PUBLISHER]

This paper presents a new family of hybrid Z-source boost dc–dc converters intended for photovoltaic applications, where the high step-up dc–dc converters are demanded to boost the low-source voltages to a predefined grid voltage. Because the boost capabilities of the traditional Z-source networks are limited, the proposed converters are composed of combine traditional Z-source networks in different ways to enhance the boost abilities of the traditional Z-source networks. The new version of the proposed Z-source converters is termed as hybrid Z-source boost dc–dc converters to satisfy the traditional benefits of Z-source networks with stronger voltage boost abilities which can also be applied to dc–ac, ac–ac, and ac–dc power conversions. The performances of the proposed converters are compared with other Z-source networks behaviors. The simulation and experimental results of the proposed converters are validated at different operating conditions. [ABSTRACT FROM PUBLISHER]

The five-phase coupled-inductor inverter is a newly proposed option for three-level five-phase inverter drives. This paper comprehensively analyzes the inverter including the coupled-inductor current, current stress on the dc-link capacitors, and a comparison of these performance aspects using three pulse width modulation (PWM) strategies. Mathematical derivations of the inverter currents and the associated current stress reveal that the current stress is not only influenced by the choice of modulation strategy, as in the neutral-point-clamped topology, but also by the value of coupled inductance; furthermore, the choice of the modulation strategy impacts the core loss of the coupled inductors. Three carrier-based PWM methods are considered: sinusoidal PWM (SPWM), and two methods with the common-mode voltage reduction (referred to as CMVR1 and CMVR2) for the five-phase coupled-inductor inverter. CMVR2 is shown to be the best solution if common-mode voltage reduction is required. The analysis demonstrates that SPWM performs better with respect to current stress and inverter losses, therefore is the preferable modulating strategy for the five-phase coupled-inductor inverter if common-mode voltage reduction is not required. The analysis is verified by simulations and experiments. [ABSTRACT FROM AUTHOR]

This paper introduces a combination of two proposed efficiency improvement techniques for a microinverter with current mode control zero-voltage switching output stages. The first technique is dynamic dead-time optimization wherein pulse width modulation dead times are dynamically adjusted as a function of load current. The second method is advanced phase skipping control which maximizes inverter efficiency by controlling power on individual phases depending on the available input power from the photovoltaic source. Neither of the techniques requires any additional circuit components and both can be easily implemented in digital controller firmware. The two techniques were designed and implemented in a 400-W three-phase microinverter prototype. The experimental results validate the theoretical analysis of these techniques and demonstrate that a significant efficiency improvement can be achieved by combining the two proposed control techniques. [ABSTRACT FROM AUTHOR]

In this paper, a new isolated high step-up dc–dc converter is proposed based on the quasi-switched-boost network. The proposed converter has the following features: 1) continuous input current; 2) reduced turn ratio of the isolated transformer; 3) increased reliability, as it can operate in either short-circuit mode or open-circuit mode without causing damage to the power converter; and 4) unchanged primary and secondary voltage waveforms of the transformer, although the shoot-through duty cycle is variable. Compared to the quasi-Z-source-based isolated dc–dc converter, the proposed converter uses fewer passive components. The operating principles, analysis, parameter design guideline, and comparison with the quasi-Z-source-based isolated dc–dc converter are presented. A 450 W prototype is built to test the proposed converter. The proposed converter is applicable for distributed power generation applications where a varying low dc input voltage is converted to a high stabilized dc output voltage with a galvanic separation requirement. [ABSTRACT FROM AUTHOR]

Multiterminal converters eliminate using several single-input-single-output converters and simplify their topologies and reduce their cost. In this paper, a new family of multi-input converters based on three switches leg is introduced. Inputs of the proposed converters are similar and they are topologically interchangeable and have boost or buck operation modes. The proposed converter has one output that operates as an inverter. Here, all operating modes of the proposed converters and their effects on each other are investigated, in details. Also, an appropriate switching technique for the converters is given. A detailed comparison between conventional and proposed two-input converters is also presented. A two-input, one-output prototype converter has been implemented to validate the given analyses and to verify the proposed converter's performance. The experimental results are in good agreement with the theoretical and simulated analyses. [ABSTRACT FROM AUTHOR]

In this paper, a new topology for half-bridge switched boost inverter (HB-SBI) is proposed. The proposed half-bridge inverter uses more active elements rather than capacitors and inductors in comparison with the conventional half-bridge Z-source inverter with two Z-networks, which results in reduction of weight, size, and cost. Moreover, the proposed inverter has the capability of eliminating inverter leg short-circuit issues and is able to further increase the output voltage level in comparison with its conventional types. Generating zero-level output voltage is also another advantage of this topology. Based on theoretical calculations, the steady-state and small-signal analysis of the proposed topology in different operating modes are performed and the ripple of inductors’ current and capacitors’ voltage are also calculated. A comprehensive comparison is also made between the proposed inverter and the conventional types. Finally, the experimental results are provided to reconfirm the performance of the proposed inverter. [ABSTRACT FROM PUBLISHER]

In this paper, a common grounded Z-source dc–dc converter with high voltage gain is proposed for photovoltaic (PV) applications, which require a relatively high output–input voltage conversion ratio. Compared with the traditional Z-source dc–dc converter, the proposed converter, which employs a conventional Z-source network, can obtain higher voltage gain and provide the common ground for the input and output without any additional components, which results in low cost and small size. Moreover, the proposed converter features low voltage stresses of the switch and diodes. Therefore, the efficiency and reliability of the proposed converter can be improved. The operating principle, parameters design, and comparison with other converters are analyzed. Simulation and experimental results are given to verify the aforementioned characteristics and theoretical analysis of the proposed converter. [ABSTRACT FROM PUBLISHER]

In this paper, a novel grid-connected high step-up inverter is proposed. The topology is composed of two stages. The first stage is a single-switch high step-up dc–dc converter with bipolar outputs, and the second stage is a conventional half-bridge dc–ac grid-connected inverter. Negative grounding of the photovoltaic (PV) module has resulted in elimination of unwanted ground leakage currents in the PV system. Simple structure, employing few semiconductor switches, simple control, and high efficiency are the features of the proposed topology. Theoretical analysis and principal operation of the circuit are discussed. An experimental prototype is implemented to verify the performance of the proposed inverter. The experimental results confirm the aforementioned features and the theoretical analysis of the converter operation. [ABSTRACT FROM PUBLISHER]

This paper proposes a new topology for an enhanced-boost Z-source inverter (ZSI) with combined two Z-impedance networks. By two Z-impedance networks and low shoot-through duty cycle, the proposed inverter produces high output voltage gain. In traditional ZSIs for high boosting voltage, a low modulation index is required; hence, under these conditions, the output voltage will have low quality with high total harmonic distortion. Compared with the conventional high-boost ZSI topologies, the proposed inverter uses shorter shoot-through duration and a larger modulation index to improve the output waveform quality. Comparison between the proposed topology and previously proposed schemes, in terms of inductor numbers, voltage and current stresses on elements, sizes of inductors and capacitors, efficiency, and switching device product (SDP) factors of diodes, is made, and the results verify the priority of the proposed topology. The operating principle of the proposed topology is analyzed in detail. Both simulation and experimental results verify the high performance of the proposed inverter. [ABSTRACT FROM PUBLISHER]

In this paper, the two-input buck converter is proposed as the dc/dc stage for photovoltaic (PV) cascaded converters. This converter is attractive for this application because it is cost effective and reliable and can achieve dual maximum power point tracking (MPPT) with only one power transistor. However, due to the simplified and integrated structure, the nonlinear characteristics of the converter and the two PV arrays complicate the control. By means of a small-signal modeling, the control theme of the two PV voltages is formulated, and the effect of the nonlinearities is presented. It is shown that, while fast voltage dynamics are achieved for the first input, the second-input voltage response depends on the second-stage converter control. Simulation and experimental results are reported to validate the theoretical analysis, showing the dual MPPT capability. [ABSTRACT FROM PUBLISHER]

According to the requirement of fuel cell generation system, this paper presents a new single-stage and boost-voltage grid-connected inverter, as well as the signal modulation diagram in a line cycle. In the proposed inverter, one of the bridge legs is shared with a boost converter. The boost inductor current is designed in discontinuous conduction mode, which can effectively decrease low-frequency current ripple (LFCR) in the output current of the fuel cell. The switching modes of the proposed inverter are analyzed in positive and negative half line cycles, respectively. The LFCR in the output current of the fuel cell is analyzed, from which the design principle of the boost voltage inductor is obtained. The per-unit current values of the shared switches and the loss of the whole system are derived and compared with those of the conventional inverter. Experimental verifications are presented to verify the theoretical analysis. [ABSTRACT FROM PUBLISHER]

This paper proposes an improved half-bridge inverter with wide-input-voltage capability for ozone-driven circuits. The study is motivated because the limited regulation of input voltage often affects the operation flexibility of ozone-driven circuits. Therefore, a modification of a half-bridge inverter along with a multiwinding coil design is proposed in this study, anticipating an increase in the range of input voltage and benefiting the industry applications. To confirm the practicality of this method, a hardware circuit was made with extensive validation. Experimental outcomes support the feasibility of this proposed method for ozone generators, exhibiting a potential of the method extending to other voltage-source applications. [ABSTRACT FROM PUBLISHER]

This paper presents a multifunctional onboard battery charger for plug-in electric vehicles (PEVs). The proposed battery charger consists of three H-bridge modules including a selective switch, a high-frequency transformer, and inductors. The first duty of the proposed charger is to charge the propulsion battery when PEV connects to the ac grid [onboard charger (OBC)]. In this case, the proposed charger plays a role in ac-to-dc converting with power factor correction. Occasionally, the propulsion battery can supply surplus energy to the grid [vehicle to grid (V2G)]. In this second task, the proposed charger acts as an inverter. The third role is to charge the auxiliary battery via the propulsion battery when PEV is in a driving state [low-voltage dc-to-dc converter (LDC)]. In this case, the proposed charger acts as a step-down converter. In conventional PEVs, the aforementioned functions are done by an OBC and an LDC separately. The proposed charger can implement the three tasks by sharing switches and inductors in an all-in-one system. Thus, the proposed approach can realize a small and light design of the EV battery charger, resulting in the improvement of fuel efficiency. After theoretical analysis, we carry out simulations and experiments using a prototype to verify the validity of the proposed approach. [ABSTRACT FROM PUBLISHER]

A switched boost inverter (SBI) can replace a $Z$-source inverter (ZSI) in low-power applications because it has one less $LC$ pair than the ZSI. This paper presents a class of quasi-SBIs (qSBIs) that offers several advantages when compared with a conventional SBI, including reducing the voltage stress on the capacitor, increasing the boost voltage factor, and improving input current profiles. Operating principles, steady-state analysis, and comparisons with conventional inverters are presented. A prototype based on a TMS320F28335 digital signal processor is built to verify the operating principle of the proposed qSBIs. [ABSTRACT FROM PUBLISHER]

The voltage range of a renewable energy source, such as the photovoltaic cell, is influenced by the environment, light, temperature, and so on. The power conditioning system should adapt to the wide input voltage and have buck–boost ability. Based on the structure of the “ac/ac unit,” this paper presents a novel active buck–boost inverter (ABI) topology suitable for wide-range input, which can realize buck–boost conversion in a quasi-single-stage inverter. The ac/ac unit composed of active switches is utilized to perform voltage boost without introducing additional passive elements, which is in favor to the system power density and efficiency. Operational analysis in buck and boost modes are presented, and the modulation strategy applied in the ABI is also developed. Simulation and experimental results are presented to verify the operational principle and its modulation strategy. [ABSTRACT FROM PUBLISHER]

High-boost dc-ac inverters are used in solar photovoltaic (PV), fuel cell, wind energy, and uninterruptible power supply systems. High step-up and step-down capabilities and shoot-through immunity are some of the desired properties of an inverter for a reliable, versatile, and low-distortion ac inversion. The recently developed Z-source inverter (ZSI) possesses these qualities. However, the realization of ZSI comes at a cost of higher passive component count as it needs two sets of passive filters. A switched boost inverter (SBI) has similar properties as ZSI, and it has one L\-C pair less compared to ZSI, but its gain is less than ZSI. This paper proposes the current-fed switched inverter (CFSI) which combines the high-gain property of ZSI and low passive component count of SBI. The proposed inverter uses only one L\-C filter and three switches apart from the inverter structure. The inverter topology is based on current-fed dc/dc topology. Steady-state analysis of the inverter is presented to establish the relation between the dc input and the ac output. A pulse width modulation (PWM) control strategy is devised for the proposed inverter. An experimental prototype is built to validate the proposed inverter circuit in both buck and boost modes of operation. A 353-V dc-link and a 127 V (rms) ac are obtained from a 35.3-V dc input to demonstrate the boost mode of operation. A 200-V dc-link and a 10.5-V (rms) ac are obtained from a 37.8-V dc input to verify the buck mode of operation of CFSI. [ABSTRACT FROM PUBLISHER]

This paper presents a novel direct current-fed interleaved phase-modulated single-phase unfolding inverter for fuel-cell applications. Two active-clamped zero-voltage switching current-fed half-bridge isolated converters are interleaved in parallel input and series output configuration. Phase modulation is proposed to control these two converter cells, which generate a rectified sinusoidal pattern at the dc link. A simple H-bridge unfolding dc–ac inversion is used to produce single-phase sine voltage at line frequency switching using square-wave control. This not only simplifies the inversion stage in terms of modulation but also reduces the switching losses. Direct front-end current-fed based unfolding inverter is not reported in literature yet. Detailed analysis and design of the proposed direct current-fed single-phase unfolding inverter has been presented. Simulation waveforms using PSIM 9.0.4 are given to verify the presented analysis and design. Experimental results on a laboratory prototype rated at 200 W are demonstrated to support the investigation, to validate the accuracy of the proposed analysis and design, and to test the performance. [ABSTRACT FROM PUBLISHER]

This paper proposes the pulsewidth modulation (PWM) strategy of Z-source inverters (ZSIs) with minimum inductor current ripple. In existing PWM strategy with single-phase shoot-through, the shoot-through time interval is divided into six equal parts, therefore the three phase legs bear the equal shoot-through time interval. In this manner, the allotment and arrangement of the shoot-through state is easy to realize, but the inductor current ripple is not optimized. This causes to use relatively large inductors. In the proposed PWM strategy, the shoot-through time intervals of three phase legs are calculated and rearranged according to the active state and zero state time intervals to achieve the minimum current ripple across the Z-source inductor, while maintaining the same total shoot-through time interval. The principle of the proposed PWM strategy is analyzed in detail, and the comparison of current ripple under the traditional and proposed PWM strategy is given. Simulation and experimental results on the series ZSI are shown to verify the analysis. [ABSTRACT FROM PUBLISHER]

Radio-frequency identification (RFID) technology has been widely used in passive RFID localization application due to its flexible deployment and low cost. However, current passive RFID localization systems cannot achieve both highly accurate and precise moving object localization task owing to tag collisions and variation of the behavior of tags. Most researchers increase the density of tag distribution to improve localization accuracy and then consider using either anti-collision process embedded in the hardware of the RFID reader or advanced localization algorithms to enhance localization precision. However, advanced anti-collision processes for RFID devices are challenged by the physical constraint characteristics of radio frequency; and improved localization algorithm cannot fundamentally reduce the impacts of tag collision on localization precision. This research work attempts to improve localization precision of a passive RFID localization system by using sparsely distributed RFID tags. This paper first defines a measure for accuracy and precision in a passive RFID localization system with regard to RFID tag distribution. An exponential-based function is then derived from experimental measurements, which reflects the relationship between RFID tag distribution and localization precision. This function shows that localization precision is mainly determined by tag density of RFID tag distribution. Based on the experimental findings, a sparse RFID tag distribution approach is proposed. The results show that in comparison with the conventional RFID tag distribution, passive RFID localization system with sparse RFID tag distribution can deliver a higher localization precision for the required accuracy. [ABSTRACT FROM PUBLISHER]

In this paper, a number of alternate-cascaded switched-inductor and tapped-inductor networks have been proposed for Z-source inverters. The resulting topologies have enhanced voltage-boost capability while retaining the usual voltage-buck flexibility of a conventional voltage-source inverter. The enhanced capability is achieved by using lower rated components that can more readily be found. These components are assembled without direct series connection and hence avoid unbalanced voltage sharing problems and losses linked to balancing resistive circuits. The component count is, however, high, meaning that the proposed inverters should only be considered when a design requires multiple lower rated components rather than a few higher rated ones. Analysis, simulation, and experimental results have already validated the concepts discussed. [ABSTRACT FROM PUBLISHER]

This paper is devoted to the step-up dc/dc converter family with a cascaded quasi-Z-source network (qZS-network). The cascaded (two-stage) qZS-network could be derived by the adding of one diode, one inductor, and two capacitors to the traditional quasi-Z-source inverter (qZSI). The proposed cascaded qZSI inherits all the advantages of the traditional solution (voltage boost and buck functions in a single stage, continuous input current, and improved reliability). Moreover, as compared to the conventional qZSI, the proposed solution reduces the shoot-through duty cycle by over 30% at the same voltage boost factor. Theoretical analysis of the two-stage qZSI in the shoot-through and non-shoot-through operating modes is described. The proposed and traditional qZS-networks are compared. A prototype of a step-up dc/dc converter with the cascaded qZS-network was built to verify the theoretical assumptions. The experimental results are presented and analyzed. Finally, a further optimization method of the cascaded qZS-network is proposed, and some practical design issues are discussed. [ABSTRACT FROM PUBLISHER]

This paper presents a novel single-stage charge-pump (CP) power-factor-correction (PFC) electronic ballast for metal halide (MH) lamps driven with the low-frequency square-wave current to avoid the acoustic-resonance problem. In order to achieve high power factor (PF) and meet the International Electrotechnical Commission (IEC) regulation, the CP PFC technique is applied to the full-bridge inverter of the conventional electronic ballast. Based on the analyses of the operational modes for the proposed electronic ballast, the design criteria of the CP components and the main inductor in the full-bridge inverter for the proposed electronic ballast are presented. A prototype circuit for a 35-W MH lamp is implemented to confirm the presented design criteria. [ABSTRACT FROM AUTHOR]

A novel switched-capacitor inverter is proposed. The proposed inverter outputs larger voltage than the input voltage by switching the capacitors in series and in parallel. The maximum output voltage is determined by the number of the capacitors. The proposed inverter, which does not need any inductors, can be smaller than a conventional two-stage unit which consists of a boost converter and an inverter bridge. Its output harmonics are reduced compared to a conventional voltage source single phase full bridge inverter. In this paper, the circuit configuration, the theoretical operation, the simulation results with MATLAB/SIMULINK, and the experimental results are shown. The experimental results accorded with the theoretical calculation and the simulation results. [ABSTRACT FROM PUBLISHER]

This paper proposes an energy regeneration circuit for three-phase voltage-fed inverters using a modified Undeland snubber. The proposed system uses a quasi-square-wave zero voltage switching dc–dc auxiliary converter to regenerate the energy from snubber capacitor to the dc bus. The regenerative circuit uses a single active switch, and it operates independently of the three-phase inverter. Operation stages, theoretical waveforms, and a design methodology are presented. Experimental results based on a 4.5-kVA three-phase inverter prototype are included to validate the proposed topology. [ABSTRACT FROM PUBLISHER]