Search

Satellite dc–dc power converters are required to have electromagnetic interference (EMI) compatibility as well as high reliability. The requirement of high reliability limits the complexity of the structure as well as the number of low-reliability components. In this paper, a conventional active-clamp-forward (ACF) topology is examined for a satellite converter owing to its relatively simple structure, small number of components, and good clamping capability regarding its switch voltage stress. However, it has a pulsating input current shape, a high di/dt level, and high switch voltage stress, which are disadvantageous with regard to the EMI filter size and high-input-voltage converter applications. To overcome these drawbacks, a new ACF topology with a continuous input current waveform is proposed. In the proposed waveform, the voltage stresses on the main switches are relieved, which is crucial to ensure the reliability of satellite FET switches, by utilizing a two-series connected structure. These features allow the proposed converter to serve as a high-input-voltage, high power-density satellite converter. In this paper, 100 W prototype converters with 50 V inputs operating at 300 kHz are built with a high power density of 47.9 W/in3. Experiments on these prototype converters are carried out to verify the features. [ABSTRACT FROM AUTHOR]

In this paper, a new modular and active snubber cell, easily applicable, and attractive for converters, especially have many switches proposed. This snubber cell is implemented on the single phase of a grid-connected three-phase T-type three-level inverter (T-3LI). In this new converter, the main switches turn-on under zero-voltage transition and turn-off under zero-voltage switching (ZVS). Also, auxiliary switches turn-on under zero-current switching and turn-off under ZVS. All snubber diodes operate under soft switching (SS). There are no additional current and voltage stresses on the main switches. During an SS operation, the switching energies are transferred to a dc voltage source. Then, these energies are processed to input with an independent dc–dc converter. Thus, all switching energies are recycled. In this paper, the principle operation and steady-state analysis of the modular and active snubber cell for a single-phase T-3LI are presented and experimental results, rated 1 kW and 100 kHz, are provided to verify theoretical analysis. [ABSTRACT FROM AUTHOR]

This paper presents a unified second-stage LC filter applied in the three-state switching cell buck–boost converter, which provides current and voltage with low ripple and low noise. The unified second-stage filter promotes a reduction in the number of devices while maintaining the filtering performance of the converter, with second-stage LC filters at the input and at the output. Moreover, the unified filter, when associated with a three-state switching cell buck–boost converter, allows a size reduction of filter devices, especially for designs with duty cycle range around 1/2. Furthermore, the unified filter arrangement provides nondissipative clamping of switching devices and reduce the system order when compared to the converter with second-stage LC filters. In this paper, the static and dynamic characteristics of the proposed converter in continuous conduction mode (CCM) are reported. Experimental data were obtained from a laboratory prototype with an input range of 32 $\sim$ 72 V, constant output of 48 V, a load of 150 W, and switching frequency of 45 kHz. The measured efficiency for the rated load was 97% for maximum input voltage. A comparison of the size and performance of the proposed filter with the topology that uses second-stage LC filters at the input and at the output is also presented. [ABSTRACT FROM AUTHOR]

In this paper, many impedance-source inverters with coupled inductors have been investigated to obtain a high step-up boost ratio. However, the leakage inductors in these topologies induce great voltage spikes at the dc link, which will increase the voltage stress of switches. Thus, the power level of inverters is limited. Furthermore, the efficiency of the inverters can be degraded by the losses associated with leakage inductors. To address abovementioned issues, this paper proposes a family of low-spike high-efficiency Y-source inverters. The proposed inverters have the ability of eliminating voltage spikes at the dc link and recycling the leakage energy via the additional diode and capacitor. In order to show the excellent characteristics of the proposed topologies, this paper compares the performances of the proposed inverters and the improved-Y-source inverter in many aspects. Simulation and experimental results have verified the abilities of the proposed inverters. [ABSTRACT FROM AUTHOR]

Turbomolecular pumps with ultrahigh vacuum performances are a desired technology among modern vacuum systems, which requires the pump to synchronously possess the wide pumping speed and high vacuum. This paper describes a systematic design methodology for a magnetically levitated turbomolecular pump with consideration of multiphysics constraints, such as the mechanical strength, rotor dynamics, electromagnetic losses, and thermal characteristic. These variables will directly decide the acquisition of high vacuum performances. The design process for such high-performance pumps requires multidisciplinary and highly iterative due to the complex interaction of the many design variables involved. The structure of the bladed rotor is determined in terms of the material selection and mechanical verification. In this paper, an effective modeling method is presented to achieve accurate bending modes of the bladed rotor. An assessment on the loss level and the thermal limit is performed to ensure the temperature rise of the pump within the acceptable range. The measured results show that the pump can achieve the high vacuum performance with the pumping speed of 4370 l/s and the lowest working pressure of 10–8 magnitude. The proposed design process described in this paper provides the general guidelines for the multidisciplinary design of high-performance turbomolecular pumps. [ABSTRACT FROM AUTHOR]

This paper presents a novel integrated-stage light-emitting diode (LED) driver based on Flyback and resonant converters. The Flyback converter realizes power factor correction in the discontinuous conduction mode. The resonant converter is operated as a dc–dc converter to support the LED loads. Moreover, the resonant converter can clearly decrease the drain–source voltage of the active switch and exhibits zero-voltage-switch characteristics. Therefore, a cost-effective MOSFET can be chosen as the main control component that can decrease the cost of the whole system. Compared to a single-active-switch converter (such as Class-E converter), the number of passive components in the resonant converter can be limited to four. Therefore, the power density of the system can be improved drastically. In this paper, a 100-W prototype is presented under the experimental condition to validate the proposed integrated-stage LED driver. [ABSTRACT FROM AUTHOR]

A high-speed squirrel-cage induction machine requires a totally different design compared to the traditional squirrel-cage industrial motor because of the mechanical limitations caused by the high speed. This results in a more complicated rotor construction and expensive material selection, and sets higher standards for the manufacturing precision. The objective of this paper is to demonstrate the design aspects, material selection, and manufacturing of a squirrel-cage rotor for high-speed applications. In this paper, the rotor dimensioning approach based on equations and data analysis is presented. Rotor material selection and construction topology influence on the electrical machine design are discussed. The results are illustrated with the design of a 6-kW, 120 000-r/min induction machine for a turbo circulator. The influence of rotor parameters on the electromagnetic performance of the designed machine is demonstrated. Mechanical stresses for different topologies are studied with finite-element method analysis. Several manufacturing methods for producing a high-precision rotor are described and compared. The presented rotor design approach, which enables high electromagnetic performance and robust construction, is verified by the testing of a prototype. [ABSTRACT FROM AUTHOR]

In this paper, a series-capacitor-based interleaving buck power factor correction (PFC) converter is proposed, the intermediate energy storage capacitance of which is operated at discontinuous capacitor voltage mode (DCVM), and automatic power factor (PF) correction for this converter is obtained. Moreover, the voltage across the series capacitor of the proposed PFC converter is clamped at the input voltage, and thus peak voltage stress existed in the traditional DCVM buck PFC could be relieved. By effectively regulating the charge/discharge time for the series capacitor, ultrahigh step-down conversion ratio of the proposed converter is achieved, the conversion ratio of which is independent of the duty cycle and only related to the switching frequency and circuit parameters. Therefore, high PF can be obtained due to very narrow deadtime of the input current. Meanwhile, the proposed PFC converter can realize the soft turn-on of part power switch and soft turn-off of part power diodes. In addition, comparing with the traditional discontinuous inductor current mode PFC, the input current of the proposed PFC converter is continuous so that the peak value and root-mean-square value of input current can be reduced. The operational principle, performance analysis, and parameter design principle are given in this paper. The analysis results show that the PF and total harmonic distortion are also independent of the duty cycle. Finally, a 220-Vac input, 60 W/15 V output experimental prototype is built to verify the validity of the theoretical analysis. [ABSTRACT FROM AUTHOR]

Three-port converters with high voltage gain are desirable solutions for integrating renewable energy and energy storage devices into high voltage dc bus. A high gain three-port converter with soft switching is proposed in this paper, which can realize zero voltage switching for all switches and zero current switching for all diodes in various operating modes. Single coupled inductor is used to achieve high voltage gain and to reduce the voltage stress of switches so that switches with low on-resistance can be selected to reduce the conduction loss. In addition, the advantages of fewer components, higher voltage gain, and very low switch voltage stresses make the proposed converter more suitable for application in renewable energy systems than similar solutions. Various operating modes, performance analysis, design considerations, efficiency analysis, and control method of the proposed converter are discussed. A laboratory prototype with 30 V renewable energy source, 48 V energy storage device and 400 V output is designed to verify the performance of the proposed three-port converter. [ABSTRACT FROM AUTHOR]

Soft-switching techniques of transformerless photovoltaic grid-connected inverters (TLIs) can significantly reduce switching losses, as well as soften switching processes. Conventional dc–ac soft-switching configurations proposed by Dr. Deepakraj M. Divan are invalid in TLIs because of the leakage current problem. In order to develop soft-switching techniques in TLIs, this paper proposes a new soft-switching configuration and a procedure to guide the invention of soft-switching TLIs. First, this paper proposes two basic resonance tanks related to dc bus polarities, and then, uses these basic tanks to elevate four popular full-bridge-type TLIs according to the proposed guideline. As a result, four soft-switching TLIs are gained. Second, this paper picks obtained soft-switching highly efficient and reliable inverter concept (HERIC) as example to analyze its soft-switching operation principle and performance. As a consequence, all active switches of the gained soft-switching HERIC circuit are switched under both of zero-current turn-on and turn-off conditions; the reverse recovery problem of freewheeling diodes is alleviated owing to the zero-current turn-off of diodes; meanwhile, the common-mode voltage at the switching frequency scale is still constant. Finally, some experimental results from a 3-kW universal prototype at 50-kHz switching frequency are provided to verify the effectiveness of the main contributions of this paper. [ABSTRACT FROM AUTHOR]

In this paper, two structures are proposed for the switched-inductor quasi-Z-source inverter. In the proposed structures to extend the voltage gain of inverter, two new switched-inductor structures are used. In the proposed structures, voltage across the capacitors in the Z-source network and in the switched-inductor is symmetric and small. The other advantage of proposed inverters is known as achieving higher voltage gain per smaller duty cycle ratio (of shoot-through). Compared with a conventional continuous input current switched-inductor quasi-Z-source inverter at the same gain voltage, there is less of a ripple of input current in the proposed inverters. In this paper, at first the both the conventional and the proposed switched-inductor Z-source inventers are thoroughly investigated to find out their governing relations. Then, the proposed Z-source inverters are compared with the conventional ones by simulating them to assess their performance efficiency. Next, applying the simple boost pulse width modulation the simulation is carried out with PSCAD/EMTDC software. After that, to evaluate the obtained results, the prototypes of the proposed inverters with 48 Vdc input voltage are used. [ABSTRACT FROM PUBLISHER]

A comprehensive analysis for a family of two-level pulsewidth modulation plus phase-shift (PPS)-modulated-isolated-bidirectional dc–dc converters is presented in this paper. Compared with the traditional phase-shift control, the PPS control features reduced current stresses, reduced conduction losses, guaranteed zero-voltage switching (ZVS) operation, and wide conversion-ratio variation range. In this paper, all eight operation modes are revealed, and then the unified solution of the power transmission capability for each mode is proposed, applicable for any two-level PPS converters. Based on the unified solution, component stresses and ZVS operation are analyzed to assist component selection. Most importantly, the control maps for three different combinations of the two-level PPS converters are proposed, to assist converter operation and design in the low-circulating-current region. In the control map, a circuit parameter k is proposed and its upper limit is found, providing a design limit to select switching frequency, leakage inductance, turns ratio, and power level. A 29–67 V/380 V prototype—the combination of group C plus group A—rated at 100–1000 W was built. The analysis is verified by both simulation and experimental results. [ABSTRACT FROM PUBLISHER]

A new isolated single-stage soft-switching power-factor-correction (S4 PFC) driver for supplying light-emitting diodes (LEDs) is introduced in this paper. In the proposed LED driver, the switches voltage stress and also the dc-bus voltage is limited to the peak of the line voltage. Hence, low voltage rated mosfets and diodes can be used. The efficiency is improved because the switches are turned on under zero current switching (ZCS) condition and turned off under zero voltage zero current switching (ZVZCS) condition. Also, no current feedback is required since the converter provides an output current independent of output voltage. In this paper, operating principle of the proposed LED driver is presented and design considerations are discussed. To verify the theoretical analysis, a laboratory prototype of the proposed converter for supplying a 50 W/70 V LED module from 220 Vrms/50 Hz ac mains is implemented, and the experimental results are presented. Since current feedback is not used, dimming property and operation for universal voltage range is not achievable. [ABSTRACT FROM PUBLISHER]

In this paper, the lifetime prediction of power device modules based on the linear damage accumulation is studied in conjunction with simple mission profiles of converters. Superimposed power cycling conditions, which are called simple mission profiles in this paper, are made based on a lifetime model in respect to junction temperature swing duration. This model has been built based on 39 power cycling test results of 600-V 30-A three-phase-molded IGBT modules. Six tests are performed under three superimposed power cycling conditions using an advanced power cycling test setup. The experimental results validate the lifetime prediction of the IGBT modules based on the linear damage accumulation by comparing the test results with the predicted lifetime from the lifetime model. Furthermore, the test results show the importance of the junction temperature swing duration effect for the lifetime prediction of IGBT modules under power converter applications. [ABSTRACT FROM AUTHOR]

The phase-shifted full-bridge (PSFB) converter is widely employed in high-power applications. However, circulating current, narrow range of zero-voltage switching (ZVS), duty-cycle loss, and secondary parasitic oscillation are the main drawbacks of the traditional PSFB converter. This paper proposes an improved full-bridge converter to solve the drawbacks of the traditional PSFB converter. In the proposed converter, a coupled inductor with three windings is introduced to adjust the available ZVS energy and to transfer power to the output side during freewheeling period. Due to this structure, output filter requirement, circulating current, the required ZVS energy, and secondary voltage oscillation can be reduced. Thus, the proposed converter can obtain higher conversion efficiency than the traditional PSFB converter. In this paper, the detailed operation principles and experimental results are presented. [ABSTRACT FROM PUBLISHER]

In this paper, a nonisolated dc–dc converter with high voltage gain is presented. Three diodes, three capacitors, an inductor, and a coupled inductor are employed in the presented converter. Since the inductor is connected to the input, the low input current ripple is achieved, which is important for tracking maximum power point of photovoltaic panels. The voltage stress across switch S is clamped by diode D 1 and capacitor C1. Therefore, a main switch with low on-resistance RDS (on) can be employed to reduce the conduction loss. Besides, the main switch is turned on under zero current. This reduces the switching loss. The steady-state analysis of the proposed converter is discussed in this paper. Finally, the proposed converter prototype circuit is implemented to justify the validity of the analysis. [ABSTRACT FROM PUBLISHER]

This paper presents three unidirectional step-up ac–dc converter topologies with voltage multiplication on their outputs. The first topology is the hybrid boost rectifier and the other two are novel bridgeless structures, all based on the integration of boost rectifier and the ladder switched-capacitor (SC) cell. The new hybrid structures provide high voltage gain with low voltage stress across the switches, high-power factor, and output voltage regulation. This paper presents the principle of operation, steady-state and dynamic analysis, design methodology, and experimental verification. A different approach is also presented for the design methodology of the SC cell and for the analysis of its influence on the dynamic model. Three 1000-W prototypes with a 220-V input voltage, 800-V output voltage, and 100-kHz switching frequency were designed to corroborate the theoretical study. The best efficiency was 97.1$\%$ in the proposed bridgeless versions and the voltage stress across the switches stands around 400 V. Furthermore, a comparison between the proposed structures and previous topologies is also presented. [ABSTRACT FROM PUBLISHER]

This paper investigates and evaluates the performance of a single-phase split-source inverter (SSI), where an alternative unidirectional dc–ac configuration is used. Such configuration is utilized in order to use two common-cathode diodes in a single device instead of using two separate diodes, resulting in minimum parasitic inductance in the commutation paths. In this paper, the analysis and modulation of the single-phase SSI using this alternative configuration is discussed, and the analysis of the low-frequency component in the dc side is introduced. Moreover, the features behind employing the triangular, the trailing-edge sawtooth, and the leading-edge sawtooth carriers with the single-phase SSI are discussed, and the differences among these carriers are highlighted. In order to highlight the performance of the proposed SSI, a comparative study is conducted with the two-stage architecture and the single-phase quasi-Z-source inverter (qZSI). The introduced analysis is enhanced with simulation results using MATLAB/PLECS models, where a 1-kVA single-phase SSI is designed and simulated. Finally, the designed 1-kVA single-phase SSI is implemented experimentally and tested at different operating points, i.e., at different voltage gains, and a maximum efficiency of $95.5\%$ is obtained. [ABSTRACT FROM PUBLISHER]

This paper proposes a family of soft-switching bidirectional converters. In many applications, the bidirectional converters operate over a wide range of duty cycle and load variations. In the proposed converters, in order to extend the zero-voltage switching operation range, two supplemental voltage sources utilizing passive components are implemented in the auxiliary circuit. By using this method, the soft-switching features are ensured for an extensive range of the converter duty cycles. This is achieved independent of the output power value or the converter operation mode, and so, soft switching is ensured within the entire converter operating region. In these converters, all semiconductors components are soft switched, and the auxiliary circuit does not contribute to the complexity of the control circuit. Also, no extra voltage stress exists on the main switches and the voltage stress on the auxiliary switches is lower than the main switches voltage stress. In this paper, the proposed bidirectional buck/boost converter is analyzed and to confirm the feasibility of the proposed method, experimental results of a 150-W prototype converter are presented. [ABSTRACT FROM PUBLISHER]

In the design of high-speed permanent magnet machines (HSPMMs), comprehensive effects of design parameters on the various properties of electromagnetic loss, rotor stress, rotor critical speed, and temperature distribution must be analyzed to obtain the optimal design. The aim of this paper is to examine the effects of design parameters, such as the pole number, stator slots number, number of conductors per slot, permanent magnet (PM) thickness, PM pole arc coefficient, air gap length, rotor diameter, core length, and sleeve thickness, on multiphysics performance based on a high-power HSPMM. A reasonable design is determined according to the abovementioned analysis that satisfies all specified multiphysics constraints. The theoretical results are confirmed by the experimental results on a prototype in terms of electromagnetic, mechanical, and thermal characteristics such as back electromotive force, no-load loss, full-load current, overspeed experiment, and temperature distribution. [ABSTRACT FROM AUTHOR]

Conventional voltage balancers for the bipolar low-voltage dc (LVdc) distribution system have been composed of multiple power stages, which degrade their power density and cost effectiveness. To minimize the power stages, this paper presents a single-stage voltage balancer with high-frequency isolation. This voltage balancer is based on the three-level dual-active-bridge converter. Furthermore, for the proposed voltage balancer, an enhanced switching modulation, using the two switching patterns $\alpha$ and $\beta$ , is proposed to fully balance the bipolar voltage level under unbalanced load condition and even for when one of the dc poles has no load. Besides, a closed-loop control system can be implemented by using output voltage information and proportional-integral controllers. Finally, experimental results using a 3-kW laboratory prototype converter verify the effectiveness of the proposed voltage balancer. [ABSTRACT FROM AUTHOR]

Multilevel inverters (MLI) with reduced components are becoming popular to achieve higher voltage levels with lower cost and complexities of the circuit. Most of the reduced switch MLIs use a large number of isolated voltage sources that have a large total standing voltage (TSV) and higher losses. Moreover, many reduced component MLIs have been developed to reduce the number of switches only and have not utilized the dc-link voltages properly. Thus, an inverter needs to be designed in which the number of dc sources is also small and utilized fully. In this paper, a novel single-phase, multicell MLI configuration is presented that can generate a maximum number of output voltage levels using a minimum number of switches and dc sources. Two optimal configurations of the proposed MLI are proposed based on the minimum requirements of components with the optimum voltage stress of the highest rated switches. Moreover, the TSV of the proposed optimal MLI also becomes low. A generalized multicell optimum MLI is presented and the number of components, voltage stress of all the switches, and the TSV of the proposed as well as the other inverters also determined by the generalized expressions for comparison purpose. The prototype of a specimen 15-level inverter and the optimal 75-level inverter cell is further developed and implemented using DS 1103 in the laboratory to show the effectiveness of the proposed configuration. The experimental results corresponding to the different modulation indices are presented here for the verification of the simulation results. [ABSTRACT FROM AUTHOR]

In this paper, a new transformerless buck–boost converter based on a ZETA converter is introduced. The proposed converter has the ZETA converter advantages, such as buck–boost capability, input-to-output dc insulation, and continuous output current. The suggested converter voltage gain is higher than the classic ZETA converter. In the presented converter, only one main switch is utilized. The proposed converter offers low voltage stress of the switch; therefore, the low on-state resistance of the main switch can be selected to decrease the losses of the switch. The presented converter topology is simple; hence, the control of the converter is simple. The converter has the continuous output current. The mathematical analyses of the presented converter are given. The experimental results confirm the correctness of the analysis. [ABSTRACT FROM AUTHOR]

Circuit analysis and design criteria of a two-phase bidirectional converter with high voltage gain are presented in this paper. The operating principle of the forward or reverse mode is similar to that of the conventional buck or boost converter. Compared with the conventional converter, the switch stresses can be reduced significantly depending on the operating region of the voltage ratio in the two-phase converter. The power losses can also be reduced due to the use of low-voltage rating switches. The derivate converters are discussed to demonstrate the advantages of the proposed topology. A 200 W/1 MHz two-phase prototype converter with gallium nitride (GaN) devices is built and tested to verify the feasibility. [ABSTRACT FROM AUTHOR]

In this paper, an LLC type converter with two interleaved pulsewidth modulation (PWM) rectifiers is proposed. Compared with the conventional LLC converter, it achieves a wide voltage regulation range independent of load. In the proposed structure, each secondary-side PWM rectifier can operate individually. With the interleaving technique and shared primary-side switching network, the circuit secondary-side current stress is halved and the primary-side current stress is largely reduced. Besides, the filter capacitor requirement is reduced. Therefore, the proposed structure is a good option for medium/high power wide output range applications. The symmetrical LLC resonant tanks always operate at the resonant frequency, which marks the optimal operation point of the LLC resonant tank. Therefore, the conduction loss is effectively mitigated. In the proposed converter, zero-voltage turning-on (ZVS) of the primary-side MOSFETs can be ensured and is independent of the load. Moreover, the turning-off currents of the primary-side MOSFETs are small and are also load independent. This brings the benefits of minimized circulating current and negligible turning-off loss and no MOSFET turning-off voltage spike. The secondary-side auxiliary MOSFETs turn-on with ZVS and rectifying diodes turn-off with limited di/dt. Topological analysis and experimental results of a 1.3 kW/100 kHz prototype generating 230–440 V output from 390-V input are presented. The prototype demonstrates 97.31% peak efficiency and good performance over a wide output range. [ABSTRACT FROM AUTHOR]

In this paper, a new high-frequency resonant boost converter is presented. Zero-voltage switching (ZVS) for the switches and zero-current switching (ZCS) for the rectifying diode are attained. The provided ZVS conditions reduce switching losses considerably, and ZCS conditions for the diode decrease voltage oscillations. Both switches are grounded which simplifies the gate-drive circuit and enhances the converter potential for high-frequency operation. All passive elements are high-frequency resonant type and thereby the converter power density is enhanced. The resonant inductor placed in front of the converter can operate in continuous conduction mode and smoothens the converter input current. Experimental results from a 160 W/500 kHz laboratory discrete prototype with an almost high-voltage conversion ratio of 100 to 300 V confirm the integrity of the proposed converter operation. [ABSTRACT FROM AUTHOR]

This paper proposes a novel isolated high step-down conversion circuit, called an integrated buck and modified push−pull (IBMPP) converter, which is able to lower the voltage level on the primary side of the ideal transformer, resulting in a lower turns-ratio and decreased leakage inductance. The IBMPP converter is able to prevent the duty cycle from operating in extremely low conditions. Furthermore, the proposed converter adopts active-clamp techniques to recycle leakage energy and to suppress voltage spikes, so that the conversion efficiency can be effectively improved. The advantages of the IBMPP converter are its simple topology, easy control mechanism (which requires only two signals with a 180-degree phase shift), high conversion ratio, low component counts for power switches, and less voltage stress on some of the switches on the high-voltage side. The operation principle, steady-state analysis, design considerations, and experimental results of the proposed IBMPP converter are presented in detail. The feasibility of the IBMPP is verified by hardware implementation. The full-load efficiency at 250 W is 81.44%, and the input and output voltages are 380 and 5 V, respectively. [ABSTRACT FROM AUTHOR]

In this paper, a new high voltage gain step-up dc–dc converter is proposed for interfacing renewable power generation. The configuration optimally integrates both the coupled-inductor and switched-capacitor techniques to achieve an ultra-high step-up gain of voltage conversion with low voltage stress and high efficiency. It consists of a voltage boost unit, a passive clamp circuit, and a symmetrical voltage multiplier network. The structure becomes modular and extendable without adding any extra winding for ultra-high step-up voltage gain. The proposed topology not only reduces the voltage stress on the main switch but also maintains it steady for the entire duty cycle range. Furthermore, the reverse recovery issue of the diodes is alleviated through the leakage inductance of the coupled inductor. The operation principle and steady-state analysis are presented in detail. Experimental evaluation validates the claimed advantages and demonstrates a well-distributed efficiency curve and the peak of 96.70%. [ABSTRACT FROM AUTHOR]

This paper presents a novel switch current stress reduction technique for a single switch boost-flyback high step up dc–dc converter. Coupled inductor-based converters do not have a sufficiently higher inductance value of their windings. This creates current surge during transient and steady state, which in turn increases current stress at main switch. To compensate this difficulty in coupled inductor-based boost flyback converter, an inductor–diode parallel combination has been connected in series with the switch. This technique increases the effective inductance of the coupled inductor primary winding during switch turn-on operation and helps to reduce current stress. Steady-state operating principle with the proposed technique is analyzed in continuous conduction mode. The current reduction technique is discussed with a proper mathematical derivation. To verify theoretical findings, simulation study is carried out in MATLAB/Simulink R2014b. Finally, a laboratory-based 40-W prototype converter is designed to show the effectiveness of the proposed switch current reduction technique. [ABSTRACT FROM AUTHOR]

This paper presents an optical pixel sensor system that uses hydrogenated amorphous silicon (a-Si:H) photo thin-film transistors (TFTs) for innovating the user interface of displays with optical input functions. The proposed optical pixel sensor applies photo TFTs that are combined with one primary color filter (red, green, or blue) to determine the input signal to the optical sensor. Other photo TFTs covered with filters of other colors are utilized to provide compensating photocurrents for achieving a robust optical input function with a high signal-to-noise ratio under intense ambient white light. To improve the lifetime of the sensor and the degradation of photo TFTs under constant drain-to-source voltage (VDS) bias stress, an alternately controlled sensing structure is proposed to reduce the effective stress time of the photo TFTs. The optical characteristics and the degradation of a-Si:H photo TFTs under VDS stress with different duty ratios are investigated to verify the effect of reduced stress time on photo TFTs. Measurements further reveal that the proposed optical sensor achieves a significant initial difference in output voltages under high-intensity ambient white light of 13 230 lx, and that the difference remains high after 408 h of long-term operation at 70 °C, demonstrating the feasibility of the alternately controlled sensing structure and the long-term reliability of the sensor. [ABSTRACT FROM AUTHOR]

A new transformerless bidirectional buck-boost converter is proposed in this paper. The proposed converter has a simple circuit structure, low component count, low voltage stress on the power transistors, and a wide voltage gain range. This makes it applicable in the energy storage charge/discharge systems, such as electric vehicles (EV), microgrids and nanogrids with energy storage units, and uninterruptible power supplies. In addition, synchronous rectification between the complementary transistors is employed to improve the converter efficiency. A comprehensive analysis of the steady-state operation, small-signal model, component parameters design, and efficiency analysis of the proposed converter operating in a continuous conduction mode is given. Finally, a 1.6-kW scaled-down prototype was built using Silicon Carbide MOSFETS to validate the effectiveness and feasibility of the proposed converter. [ABSTRACT FROM AUTHOR]

In this paper, a cooperative triple-phase-shift (CTPS) control for the isolated dual active bridge dc–dc converter is proposed first to eliminate the dual-dc side flow back currents. Furthermore, the current characteristics of the proposed CTPS control with the main variable (the primary side inner phase shift) tuned in two different regions are derived in detail and compared with each other. The tuning region of the main variable with the optimal current characteristics is finally determined based on the comparison results. As a result, the current stress is reduced and the efficiency is enhanced. The detailed experimental results of CTPS control verify its validity and practicability. The advantages of CTPS control are also highlighted by comparing it with some conventional phase shift controls. [ABSTRACT FROM AUTHOR]

With the goal to decrease weight and increase overall efficiency, power electronics is proliferating in the aircraft applications. The conventional mechanical, pneumatic, and hydraulic systems are substituted with on-board electrical distribution systems. The new power electronics based distribution architectures should comply with the airworthiness standards by providing adequate redundancy to operate even under multiple failures. However, each redundant system adds to more weight and cost, and hence optimizing redundancy without compromising safety still remains a challenge. In this scenario, modular power converters offer a promising solution for obtaining reliable operation. Apart from ensuring availability and operation of the system, the modular converters enable controlling the stress for the individual converter cell and therefore their wear-out. This paper considers the failure mechanisms of the most sensitive devices in the system, the power semiconductors, and predicts their remaining useful lifetime (RUL). Based on this RUL, an optimization of the system loading is performed in order to delay the wear-out based failures in the system without reducing the mean lifetime of the building blocks. A study case is shown in order to demonstrate the lifetime extension of the system with the proposed algorithm. [ABSTRACT FROM AUTHOR]

A nonisolated ultra-high step-down interleaved dc–dc converter with low voltage stress and common ground between the input and output ports is proposed in this paper. In order to extend the extremely narrow duty cycle, series capacitors and transformers are applied to the four-phase interleaved buck converter. In addition to extending the duty cycle, the series capacitors clamp the voltage stress across the switches and diodes, which results in using low voltage rating semiconductor components. Additionally, the main switches are turned on under a soft-switching condition. Hence, the conduction and switching losses are reduced and the overall efficiency of the designed converter is improved. Other important strengths of this topology are very low output current ripple due to interleaving and automatic uniform current sharing. The validity of theoretical analysis and converter operation is confirmed by the implementation of a 150 W prototype at 400 V input voltage and 12 V output voltage. [ABSTRACT FROM AUTHOR]

In this paper, a new multi-input multi-output (MIMO) dc–dc converter with high step-up capability is proposed for wide power ranges. Also, in order to increase each output voltage, diode–capacitor voltage multiplier (VM) stages are utilized in the proposed converter. The number of input stages, output stages, and VM stages are arbitrary and dependent on design conditions. At first, the general structure of proposed MIMO converter is presented. Then, in order to explain the converter operation, we walk through the design of a 1-kW four-input two-output example, including loss and efficiency calculations. We validate the design with a prototype that matches efficiency calculations. [ABSTRACT FROM AUTHOR]

This paper presents a new reconfiguration module for asymmetrical multilevel inverters in which the capacitors are used as the dc links to create the levels for staircase waveforms. This configuration of the multilevel converter makes a reduction in dc sources. On the other hand, it is possible to generate 13 levels with lower dc sources. The proposed module of the multilevel inverter generates 13 levels with two unequal dc sources (2VDC and 1VDC). It also involves two chargeable capacitors and 14 semiconductor switches. The capacitors are self-charging without any extra circuit. The lower number of components makes it desirable to be used in wide range of applications. The module is schematized as two back-to-back T-type inverters and some other switches around it. Also, it can be connected as a cascade modular which leads to a modular topology with more voltage levels at higher voltages. The proposed module makes the inherent creation of the negative voltage levels without any additional circuit (such as H-bridge circuit). Nearest level control switching modulation scheme is applied to achieve high-quality sinusoidal output voltage. Simulations are executed in MATLAB/Simulink and a prototype is implemented in the power electronics laboratory in which the simulation and experimental results show a good performance. [ABSTRACT FROM AUTHOR]

The interleaved bidirectional buck–boost converter dual active half-bridge (IBBC-DAHB) dc–dc converter consists of two converters IBBC and DAHB and a coupled inductor. The IBBC-DAHB converter has significant features such as low ripple current at the low-voltage side, low current stress on the input inductors, voltage stress across the switches less than the high-voltage side, high voltage gain, and zero-voltage soft switching. The converter offers high efficiency using phase-shift modulation when it operates at a nominal design operating point. However, the efficiency decreases due to high circulating current, high current stress, and limited soft-switching range when the source and load voltages deviate from their nominal values. This paper employs both duty cycle and phase-shift modulation methods to improve the above mentioned shortcomings using voltage matching for the DAHB converter. The proposed converter is analyzed and a 500-W experimental prototype with 40–60 V input voltage and 400 V output voltage under 100 kHz switching frequency is implemented to verify the theoretical results. The maximum efficiency of 97.15% is achieved at 60 V and 400 W. A flat efficiency characteristic for the converter is derived by the proposed control method, where the efficiency at 20% of nominal load is 91% and much higher than the phase-shift control, which is 70.8%. [ABSTRACT FROM AUTHOR]

In this paper, an isolated high-frequency converter with optimal switch impedance is proposed, which can achieve soft-switching characteristics and a low switch voltage stress. Meanwhile, the topology makes full use of the parasitic components of the transformer, which can reduce the number of system components and improve the system efficiency. The detailed design method of the proposed converter is analyzed. Simultaneously, an air core printed circuit board (PCB) transformer is employed to eliminate the core loss and reduce the vertical space. On the basis of the mathematical analysis, the transformer parameters can be effectively designed. A 20-MHz prototype based on the proposed topology is built. The experimental results verify the advantages of the proposed converter and the corresponding design method. [ABSTRACT FROM AUTHOR]

A nonisolated bidirectional dc–dc converter with high voltage gain, low voltage stress, low component count, and soft-switching features is presented in this paper. In this topology, coupled inductors and voltage multiplier cells are merged to achieve high step-up/down voltage gain. Also, due to using active clamp circuits, the voltage stress of power switches is relatively low. Thus, the low voltage switches with low on-resistance can be employed to reduce the conduction losses. Furthermore, zero-voltage switching is accomplished in both high step-up and high step-down modes for all power switches, and due to zero-current switching operation of all antiparallel diodes, the reverse recovery losses are reduced. In order to verify the theoretical analysis and the converter performance, a 200 W prototype circuit of the proposed converter is implemented in the laboratory. [ABSTRACT FROM AUTHOR]

This paper presents a comprehensive and generalized analysis of the bidirectional dual active bridge (DAB) dc–dc converter using triple phase shift (TPS) control to enable closed-loop power regulation while minimizing current stress. The key new achievements are a generic analysis in terms of possible conversion ratios/converter voltage gains (i.e., Buck/Boost/Unity), per unit based equations regardless of DAB ratings, and a new simple closed-loop controller implementable in real time to meet desired power transfer regulation at minimum current stress. Per unit based analytical expressions are derived for converter ac rms current as well as power transferred. An offline particle swarm optimization (PSO) method is used to obtain an extensive set of TPS ratios for minimizing the rms current in the entire bidirectional power range of –1 to 1 per unit. The extensive set of results achieved from PSO presents a generic data pool, which is carefully analyzed to derive simple useful relations. Such relations enable a generic closed-loop controller design that can be implemented in real time avoiding the extensive computational capacity that iterative optimization techniques require. A detailed Simulink DAB switching model is used to validate the precision of the proposed closed-loop controller under various operating conditions. An experimental prototype also substantiates the results achieved. [ABSTRACT FROM AUTHOR]

In this paper, a high step up converter consisting of an integrated quadratic-boost converter and a voltage doubler is proposed. The integration of the quadratic-boost converter makes the system easier to lift up its voltage gain through slightly increasing the duty ratio of the single switch. The voltage doubler further increases the voltage gain of the system as the turn ratio rises. The voltage stresses on the switch and the diodes are decreased for such cascaded topology. Different operation modes are analyzed and mathematical analysis of the converter is presented in detail. The leakage inductance contributes to realizing zero current switching of the diodes in the second boost stage and the doubler and the energy can be recycled to the load. A 38-W prototype is built to work as a vehicle LED driver. Experiments are conducted to verify the advantages of the proposed converter and the efficiency is 90% at the nominal operating point. [ABSTRACT FROM AUTHOR]

This paper explores a power-conversion system for single-phase transformerless ac module application. A nonisolated high-gain dc–dc stage is coupled with a doubly grounded dynamic dc-link inverter to implement the microinverter topology. The front-end boost stage steps up the single-module voltage to a higher dc voltage, typically to 200 or 400 V as required for the following inverter stage. It is a hybrid of an interleaved boost and switched capacitor concept capable of achieving high gain while simultaneously maintaining reduced voltage and current stress, and thus lowering switching and conduction loss for most of the switches. By directly connecting the grid neutral to the photovoltaic (PV) negative, the doubly grounded voltage swing inverter has the advantage of zero capacitive-coupled common-mode ground currents, critical for transformerless PV inverters. The two dc links of the inverter stage share the double-line frequency power decoupling with a combination of higher value of mean voltage and relatively large 120-Hz ripple component–the dynamic dc-link approach. Through an optimization algorithm, the decoupling capacitance is minimized enabling an all-film capacitor implementation while satisfying the converter's operating constraints over a wide range of power factors. The simulation as well as experimental results from a GaN-based hardware prototype validate the converter's performance. [ABSTRACT FROM AUTHOR]

A 1-MHz-modified single-ended primary-inductor converter (SEPIC) circuit is presented in this paper as an LED driver for automotive headlights. On the basis of traditional SEPIC, only a diode and two capacitors are added; therefore, the circuit structure is relatively simple and the volume is relatively small. High step-up capability is obtained with moderate duty cycle. Compared with traditional step-up circuit such as boost, low-voltage stress is gained which is beneficial to device selection. Zero-voltage switching is achieved at the same time to reduce switching loss. Planar inductors are used with the advantages of low profile and good thermal characteristic. Operational principle and parameters design process are introduced in detail. A 36-W prototype has been designed to demonstrate theoretical analysis. Obtained efficiency was up to 90.91% at full load. [ABSTRACT FROM AUTHOR]

High step-up converters are required for distributed photovoltaic generation systems, due to the low voltage of the photovoltaic source. In this paper, a new hybrid high voltage gain dc–dc converter is created by merging the standard boost converter with a coupled inductor and different switched-capacitor techniques. With a single switch and no requirement of higher duty cycle values, the proposed converter achieves a high voltage gain and high efficiency, in addition to lowered voltage and current stresses of the components. A 200-W prototype was implemented experimentally to evaluate the converter, which reached a maximum efficiency of 97.6%. [ABSTRACT FROM AUTHOR]

In this paper, a hybrid switched-capacitor/switched-quasi-Z-source bidirectional dc–dc converter is proposed for electric vehicles (EVs) with hybrid energy sources, which has a wide voltage gain range in the bidirectional energy flows. Compared with the traditional quasi-Z-source bidirectional dc–dc converter, the proposed converter only changes the position of the main power switch and employs a switched-capacitor cell at the output of the high-voltage side. Therefore, the advantages of the wide voltage gain range and the lower voltage stresses across the power switches can be achieved. The operating principle, the voltage and current stresses across the power switches, and the comparisons with other converters are analyzed in detail. Furthermore, the parameter design of the main components, the dynamic modeling analysis, and the voltage control scheme are also presented. Finally, the experimental results obtained from a 400 W prototype validate the characteristics and the theoretical analysis of the proposed converter. [ABSTRACT FROM AUTHOR]

Soft-switching inverters can achieve high efficiencies and low switchdv/dtanddi/dt, but often impose additional stress on the switches due to their resonant behavior. Multicell converters, on the other hand, can process high voltages by arranging the switches to share the stress. This paper proposes a buck–boost multicell soft-switching inverter with inherent cell voltage balancing. Both the current and voltage stresses are shared by the cells. Soft-switching conditions are achieved for all switching transitions without any need for auxiliary circuitry or clamps. A multiple-winding transformer transfers energy between the terminals and provides galvanic isolation. An analytical study and experimental results on a 1200-W prototype verify the operation of the inverter. [ABSTRACT FROM AUTHOR]

In this paper, a novel buck–boost converter with low electric stress on components and negative output voltage is proposed. The operational principle, steady-state analysis, and small-signal modeling of the proposed buck–boost converter in continuous conduction mode are presented. Comparisons among another five buck–boost converters and the proposed buck–boost converter are presented. It is found that the proposed converter's voltage gain is smaller than the other converters’ in step-down mode. Also, based upon the comparisons among the same kind and same number of components, the voltage and current stresses on the power switch of the proposed buck–boost converter are less than or equal to those of the comparative converters, and the voltage stress on the charge pump capacitor and the switching device power rating of the proposed buck–boost converter are always lower than those of other comparative converters. The efficiency of the proposed buck–boost converter is highest among those converters having the same number of elements. These advantages make component selection for the proposed converter much easier, and it can be used directly in applications needing a negative voltage source. Finally, simulation results and circuit experiments are given for validating the effectiveness of the proposed buck–boost converter. [ABSTRACT FROM AUTHOR]

This paper presents an interleaved converter that benefits the coupled inductor and built-in transformer voltage multiplier cell (VMC). Compared with the other converters with only a built-in transformer or only a coupled inductor, the combination of these techniques gives an extra degree of freedom to increase the voltage gain. The VMC is composed of the windings of the built-in transformer and coupled inductors, capacitors, and diodes. The voltage stress of MOSFETs is clamped at low values and can be controlled via the turns ratio of the built-in transformer and coupled inductor that increases the design flexibility. Moreover, the energy of the leakage inductances, is recycled to the clamp capacitors which avoids high voltage spikes across MOSFETs. In addition, the current falling rate of the diodes is controlled by the leakage inductances, and the reverse current recovery problem is alleviated. Meanwhile, due to the interleaved structure of the proposed converter, the input current ripple is minimized and the current stress of the power devices is decreased. All of these factors improve the efficiency of the proposed converter in high-current and high-voltage applications. The principle operation and steady-state analysis is given to explore the advantages of the proposed converter. Finally, a 1.3-kW prototype with 50–600 V voltage conversion is built to demonstrate the effectiveness of the proposed converter. [ABSTRACT FROM AUTHOR]

One of the future challenges in modular multilevel converters (MMCs) is how to size key components with compromised costs and design margins, while fulfilling specific reliability targets. It demands better thermal modeling compared to the state-of-the-arts in terms of both accuracy and simplicity. Different from two-level power converters, MMCs have inherent dc-bias in arm currents and the power device conduction time is affected by operational parameters. A time-wise thermal modeling for the power devices in MMCs is, therefore, an iteration process and time-consuming. This paper, thus, proposes a simple analytical thermal modeling method, which adopts equivalent periodic power loss profiles. More importantly, time-domain simulations are not required in the proposed method. Benchmarking of the proposed methods with the prior-art solutions is performed in terms of parameter sensitivity and model accuracy with a case study on a 30-MW MMC system. Experiments are carried out on a specifically designed scaled-down system to verify the electrothermal aspects. [ABSTRACT FROM AUTHOR]

In this paper, a family of automatic interleaved Dickson switched-capacitor converters (AIDSCC) and its zero-voltage switching (ZVS) resonant configuration are proposed. Different from the traditional Dickson switched-capacitor converter, the AIDSCC has symmetrical configuration with the features of automatic interleaved input current, small output voltage ripple, and lower peak capacitor voltage stress. To improve the line regulation capability, one small resonant inductor is inserted and two bulky capacitor banks are replaced by two much smaller resonant capacitors, forming the resonant AIDSCC. The transistors are ZVS turned on and diodes are zero-current switching turned off by operating above the resonance. With frequency modulation within a reasonable range, the voltage-gain range of the resonant AIDSCC is expanded significantly, while sacrificing the maximum efficiency due to the higher conduction loss. A 3X AIDSCC and a 3X resonant AIDSCC below 140 W were built to verify the analysis. [ABSTRACT FROM AUTHOR]