Search

This paper presents a new highly integrable hybrid step-down converter that merges switched-inductor and switched-capacitor operations and significantly reduces onboard loss by using the input cable's parasitic inductance as its main inductor. This converter has the inductor placed at the input with a smaller voltage swing, leading to possible use of a smaller inductor and low-voltage rating switches that generally translate to reduced conduction losses. Analyses of converter operation and losses to reveal its original characteristics and design guidelines are presented to facilitate the components optimization. The converter architecture is verified by a proof-of-concept 15-W inductor-less lithium-ion battery charger prototype that uses a 1-m USB 3.0 cable as inductor. The converter, switched at 2 MHz from a 5-V input, experimentally achieves 89.7% peak efficiency and 6% higher efficiency at full load than a Buck converter counterpart. This high efficiency and zero onboard inductor yield a relative 45.7% onboard loss reduction at full load, promising excellent integration feasibility and superior system thermal management. [ABSTRACT FROM AUTHOR]

Input-series-output-parallel (ISOP) inverter system is very suitable for high dc input voltage and large ac output current power conversion applications. If this topology is applied to the grid-connected occasion, a bulky-capacity grid-connected inverter can be built with multiple small-capacity standardized inverter modules, which can significantly improve the reliability of the system operation and facilitate system design. In this paper, we investigate an ISOP LCL-type grid-connected inverter system, and put forward an optimized way for the topology of combined LCL filters first. Then, the inverter-side inductor current is carefully chosen as the controlled variable and thus a concise distributed control method is proposed to achieve multiple control objectives. On the basis of the presented distributed control, the redundant control technique is also provided to heighten the reliability of the grid-tied ISOP inverter indeed. Finally, a three-module prototype is built and the experimental results validate the effectiveness of the raised strategy. [ABSTRACT FROM AUTHOR]

This paper proposes a novel isolated high step-down conversion circuit, called an integrated buck and modified push−pull (IBMPP) converter, which is able to lower the voltage level on the primary side of the ideal transformer, resulting in a lower turns-ratio and decreased leakage inductance. The IBMPP converter is able to prevent the duty cycle from operating in extremely low conditions. Furthermore, the proposed converter adopts active-clamp techniques to recycle leakage energy and to suppress voltage spikes, so that the conversion efficiency can be effectively improved. The advantages of the IBMPP converter are its simple topology, easy control mechanism (which requires only two signals with a 180-degree phase shift), high conversion ratio, low component counts for power switches, and less voltage stress on some of the switches on the high-voltage side. The operation principle, steady-state analysis, design considerations, and experimental results of the proposed IBMPP converter are presented in detail. The feasibility of the IBMPP is verified by hardware implementation. The full-load efficiency at 250 W is 81.44%, and the input and output voltages are 380 and 5 V, respectively. [ABSTRACT FROM AUTHOR]

Current imbalance in multistring light-emitting diodes (LEDs) is a critical issue. It may cause overcurrent in one or more LED strings, leading to rapid degradation. In this paper, a mixed high-order compensation networks-based wireless power transfer system is proposed to generate multiple constant current outputs. It is composed of an LCC resonant network in the transmitting side, a series resonant network, and multiple CLC resonant rectifiers in the receiving side. The CLC resonant rectifiers are connected in parallel to form multiple independent output channels, and each channel is then connected to an LED string. Based on the analysis of the T resonant circuit and the modeling of coupling coils, multiple constant output currents can be derived. As a result, current balance can be achieved, which is very suitable for driving multistring LEDs. The proposed system also offers a modular, scalable, and maintenance-free design, which can significantly reduce the construction cost and the control complexity. In addition, the inverter in the transmitting side can achieve zero phase angle. A laboratory prototype with dual independent output currents is built to verify the proposed method. The experimental results agree well with the theoretical analysis. [ABSTRACT FROM AUTHOR]

This paper studies a multilevel multiphase dc–ac conversion system configured by a neutral-point-clamped converter fed by multiple battery packs connected in series. A virtual-vector modulation is selected and a state-of-charge (SoC) balancing control is designed to be able to employ the full battery bank capacity, even under different battery initial SoC values or different battery nominal capacities. The SoC balancing among battery packs is accomplished through the multilevel converter operation in a lossless manner, by simply distributing the dc-to-ac power flow among the batteries according to their SoC. A simple average system model is also presented, which allows performing very fast system simulations over long periods of time and serves as a convenient tool to tune the compensator parameters. The satisfactory performance of the proposed system configuration and control, which can be applied with any number of levels and phases, has been verified through simulations and experiments in a four-level three-phase dc–ac converter fed by three lithium-ion battery packs. The results prove the feasibility and advantages of the proposed system configuration, which can be used to implement conversion systems with different specifications combining several instances of a standard battery pack and a standard power semiconductor device. [ABSTRACT FROM AUTHOR]

AC–DC light-emitting diode (LED) drivers suffer from short lifetime because of the low-lifetime electrolytic capacitors used for dc bus decoupling. In this paper, a primary-side peak current control method applied for driving a two-stage multichannel LED driver is proposed. The LED driver consists of an ac–dc boost power factor correction stage and an isolated dc–dc nonresonant stage. A long-lifetime and small film capacitor is used for implementing the intermediate dc bus. The proposed method, which controls the peak value of the primary-side current of the transformers, is applied to the dc–dc stage to ensure constant dc current output of LEDs in spite of the widely varying dc bus voltage due to low bus capacitance. The proposed method compensates the effect of the large dc bus voltage ripple by varying the switching frequency of the primary-side switches. Detailed design procedure, theoretical analysis, and experimental results of the LED driver operating at 180 W with the proposed method are provided. The LED driver with the proposed control method is proved to have high overall efficiency. [ABSTRACT FROM AUTHOR]

In this paper, a new high voltage gain step-up dc–dc converter is proposed for interfacing renewable power generation. The configuration optimally integrates both the coupled-inductor and switched-capacitor techniques to achieve an ultra-high step-up gain of voltage conversion with low voltage stress and high efficiency. It consists of a voltage boost unit, a passive clamp circuit, and a symmetrical voltage multiplier network. The structure becomes modular and extendable without adding any extra winding for ultra-high step-up voltage gain. The proposed topology not only reduces the voltage stress on the main switch but also maintains it steady for the entire duty cycle range. Furthermore, the reverse recovery issue of the diodes is alleviated through the leakage inductance of the coupled inductor. The operation principle and steady-state analysis are presented in detail. Experimental evaluation validates the claimed advantages and demonstrates a well-distributed efficiency curve and the peak of 96.70%. [ABSTRACT FROM AUTHOR]

In this paper, a high-efficiency isolated bidirectional interleaved converter (IBIC) is proposed for high step-up and high step-down conversion systems. Two inductors are used in the low-voltage side to reduce the current ripple. The IBIC incorporates an ideal transformer to achieve energy transformation and galvanic isolation; the voltage-doubler circuit in the high-voltage side not only improves the voltage gain but also minimizes the voltage stress of power switches. Clamp capacitors achieve active clamping, and the energy stored in the leakage inductance is recycled. Moreover, some switches are operated with soft-switching and slightly reduced switching losses. The prototype circuit, with low-side voltage $V_{L}$ of 48 V, high-side voltage $V_{H}$ of 380 V, and rated power of 1.5 kW, is implemented to demonstrate the functionality of the proposed IBIC. The peak efficiency levels of the proposed converter in the high step-up and high step-down stages are 95.3 and 95.8%, respectively. [ABSTRACT FROM AUTHOR]

Nanosecond pulse discharge plasma has many prospects in industrial applications, and high-voltage repetitive nanosecond pulse generators with compact design and light weight have become one of the key issues limiting its development in some applications. This paper presents a high voltage series-connected silicon carbide (SiC) metal-oxide -semiconductor field effect transistor (MOSFETs) module which can be served as the main switch in a repetitive high-voltage nanosecond pulse generator. This kind of series-connected MOSFETs module with only single external gate driver requiring very few components is very suitable for compact assembly. By analyzing the working principle, three topologies of series-connected MOSFETs module are proposed. The switching behaviors of the three different topologies with four SiC MOSFETs series-connected are compared experimentally. The variation of switching characteristics of series-connection SiC MOSFETs module with different numbers of devices are investigated. The layout is also optimized to shorten pulse front time and improve output pulse quality. Furthermore, a 10 kV SiC MOSFETs module with a turn-on transition time ∼10 ns is developed. The double pulse test result demonstrates excellent switching performances. Finally, a compact and high-voltage pulse generator composed of three 10 kV SiC MOSFETs module is tailored, with a typical rise time ∼40 ns and peak voltage of ∼30 kV. [ABSTRACT FROM AUTHOR]

Power factor correction (PFC) converter suffers from serious double-line-frequency output voltage ripple due to the difference between instantaneous ac input power and dc output power. To suppress such double-line-frequency output voltage ripple, a ripple cancellation circuit (RCC) is utilized to generate the same magnitude but 180° phase shifted double-line- frequency voltage ripple. This paper provides an insight into the relationship between control scheme and double-line-frequency ripple suppression from the perspective of audio susceptibility model. For the purpose of reducing the double line frequency ripple, the closed-loop audio susceptibility of series RCC should be designed relatively low at double line frequency. According to such requirement, a ripple controller with improved voltage feed-forward (FF) scheme and quasi-proportional-resonant (QPR) compensator is designed. As QPR compensator can increase the denominator of the closed-loop audio susceptibility, while voltage FF scheme can reduce its numerator, its magnitude at double line frequency is thus greatly reduced and double-line-frequency ripple is also significantly suppressed. Moreover, due to the flexibility of QPR compensator, the proposed ripple controller presents good ripple suppression in a different line frequency application. Finally, experimental results of a flyback PFC with buck-type RCC quasi-single-stage ac–dc converter are provided to verify the validity of the proposed ripple controller. [ABSTRACT FROM AUTHOR]

Unlike the traditional system frequency measurement-based protection in ac distribution systems, the protection in dc systems must deal with complex fault transients and identify the faulty section within milliseconds, as power electronic devices can only endure a fault current for several milliseconds. To address this problem, this paper presents a novel protection principle using transient current waveform similarity for a flexible dc distribution system. Fault current waveform characteristics are presented in detail, and cosine transient waveform similarity is adopted to fully distinguish internal and external faults. Hardware tests and simulation results show that the proposed protection can identify internal faults in less than 0.5 ms based on different fault impedances and measurement noise. [ABSTRACT FROM AUTHOR]

Two-stage isolated battery-driven grid interface (IBDGI) with front-end three-phase dual active bridge (DAB) dc–dc converter is promising to be applied in the residential battery energy storage system for supporting photovoltaic (PV) integration, load shifting, and backup power purposes. However, the second harmonic current (SHC) caused by the pulsating power of the downstream single-phase inverter will increase the battery's degradation and the component stress of the front-end converter. In this paper, a reduction method is proposed for the IBDGI with three-phase DAB converter using a load current feedforward control. The proposed idea is to incorporate virtual impedance to the output impedance of the front-end converter. The easy-to-be-implemented method does not need to modify the original voltage closed-loop controller but suppress SHC while keeping good dynamic performance. As the first step, the small-signal model of the three-phase DAB converter is provided. The parameter sensitivity analysis is proposed to demonstrate that the SHC can be well-suppressed within $\pm \text{20}\%$ parameter error of the feedforward control. Finally, a 1 kW experiment setup is built to verify the performance of the proposed SHC reduction method. [ABSTRACT FROM AUTHOR]

Power flow control in multiterminal HVdc (MTdc) grids is essential to restrict operation within permissible limits. A current flow controller (CFC) can achieve this. In this paper, the modeling, control, and simulation of resistive, RC-circuit-based, and capacitive CFCs is carried out. CFC prototypes have been developed and an MTdc grid test-rig has been employed for experimental validation. Results show that all devices achieve an effective power flow management. The impact of CFC deployment in future MTdc grids is assessed on droop-controlled converters. A voltage compensation-based method is proposed to minimize power deviations during unscheduled line current control. A protection scheme has been assessed under faults. [ABSTRACT FROM AUTHOR]

This paper deals with the analysis of the input dc-link voltage ripple in multilevel inverter based on H-bridge and level doubling network (LDN). The LDN is basically a half-bridge fed by a floating capacitor, with voltage self-balancing capability, recalling the concept of a flying capacitor configuration. The amplitude of the LDN voltage ripple is analytically determined considering both the low-order and the switching harmonic components. In particular, peak-to-peak distributions of voltage ripples over the fundamental period are analytically determined, making possible the design of dc-link capacitor relying only on the dc-voltage ripple requirements. The case study makes reference to negligible switching ripple in the output current. It well represents either grid connection or passive load having almost sinusoidal currents. Numerical simulations carried out by MATLAB/Simulink and a complete set of experimental verifications are given to confirm the theoretical developments. [ABSTRACT FROM AUTHOR]

High penetration of renewable energies through fast-response power converters results in a considerable displacement of conventional synchronous generators and losing of system inertia for frequency control. Modular multilevel converters (MMCs) can be employed serving as an interface between the large-scale renewable generation and power grids. In a microgrid with high shares of renewables integrating through MMCs, submodule (SM) capacitors can be used as energy storage to provide a degree of synthetic inertia for system frequency support. This paper quantitatively exploits the MMC synthetic inertia in a microgrid with flexible renewable penetration levels. An MMC inertia coefficient concept is proposed. It is mainly affected by the penetration ratio, the SM capacitance, and the modulation index of an MMC, with the system operation constraints. According to the analysis, a substantial portion of system inertia can be provided by properly designed MMCs. Detailed MMC frequency control loops are presented. The capacitor average voltage is proportionally linked to the frequency deviation, in order to flexibly adjust the capacitor energy during frequency events. The MMC output active power is deliberately and simultaneously regulated according to the capacitor energy change rate. By controlling the MMC capacitor voltage, dc side power, and output active power, an amount of energy can be released or absorbed by SM capacitors to improve the system frequency response during the frequency event transients, while the renewable generation is scarcely influenced. The proposed concept is experimentally verified and the results show that, with proper system parameters and control loops, the line frequency deviation and the rate of change of frequency can be significantly reduced. Good agreements of the system frequency characteristics have been achieved between the theoretical calculation and experimental results. [ABSTRACT FROM AUTHOR]

The objective of this paper is to introduce a modeling strategy to characterize the dynamics of the charge trapped in the dielectric of MOS capacitors, using diffusive representation. Experimental corroboration is presented with MOS capacitors made of Alumina in three different scenarios. First, the model predictions are compared with the trapped charge evolution due to arbitrary voltage excitations. Second, the predictions are compared with the measurements of a device in which a sigma–delta control of trapped charge is implemented. Finally, the time evolution when the device is simultaneously controlled and irradiated with X-rays is compared with the predictions. In all cases, a good matching between the models and the measurements is obtained. [ABSTRACT FROM AUTHOR]

In this paper, a novel structure of switched capacitor converter (SCC) is proposed. First, the basic unit of the proposed SCC is presented. After that, a generalized structure of the proposed SCC is discussed. The presented SCC uses one dc source, several switches, diodes, and capacitors to produce multistep dc boosted output voltage. The capacitors in the SCC can be charged in trinary asymmetrical pattern. A detailed comparative study between the proposed and other recently developed SCC structures is presented. It is shown that the proposed SCC can produce an output voltage level with lower total standing voltage and lower maximum switch stress voltage as compared to most of the suggested SCC structures. Further, a switched capacitor multilevel inverter (SCMLI) based on cross-switched multilevel inverter has been developed and analyzed for symmetric and asymmetric dc source configurations. For fair comparison with the existing SCMLI structures, the overall cost of the structures is compared based on a cost function (CF). The proposed SCMLI provides lower cost function/output voltage level (CF/NL) in comparison with most of the other SCMLI structures for both symmetric and asymmetric dc source configurations. Extensive experimental studies validate the operation and performance of the proposed SCMLI structure. [ABSTRACT FROM AUTHOR]

Beat phenomenon is an important concern in the reduced dc-link capacitance motor drive system. In previous research works, the topic is mainly concentrated on the beat phenomenon caused by the interaction of the fluctuated dc-link voltage and the motor phase voltage. In this paper, another form of the beat phenomenon generated by the fluctuated dc-link voltage and the severely fluctuated load torque is investigated. The effect of the beat phenomenon on the grid current and the motor speed is analyzed, which fluctuate with the low-frequency oscillation. In order to improve the drive system performance, a power balancing controller is proposed to suppress the grid current fluctuation, and a resonant controller is utilized to regulate the periodic power signals. Meanwhile, the applied fluctuated torque suppression method could improve the performance of the motor speed, which is only sensitive to the frequency of the fluctuated load torque. Experimental results are provided to verify the effectiveness of the proposed method. [ABSTRACT FROM AUTHOR]

In this paper, a resonant current-mode receiver is studied to charge low-voltage batteries wirelessly for supplying medical implantable systems. To increase efficiency, the root-mean-square (rms) current in the LC tank of the receiver (RX) is reduced by using a voltage-boosted current-mode (VBCM) receiver. This receiver combines the conventional current-mode receiver with a switched-capacitor converter to boost the voltage instantaneously at the switching node ($V_{X}$) of coil. Owing to the suggested technique, the receiver directly charges a low-voltage battery while maintaining a small rms current without using a complex voltage regulator. The receiver achieves an efficiency as high as 84.7% with a 1.1 V battery while operating at the resonant frequency ($f_{{\text{reso}}}$) of 6.78 MHz. The power delivered to the output ($P_{O}$) is in the range from 1.5 to 50 mW. The VBCM receiver was fabricated by 180 nm CMOS technology with a total active area of 0.22 mm2. [ABSTRACT FROM AUTHOR]

The back-to-back (BTB) converter is one of the most popular converter topologies for the control of electrical machines, power transmission systems, and power quality applications. The conventional cascade control structure is commonly used due to its simple design procedure and reliable operation. However, the bandwidth of the dc-link voltage controller has to be limited in order to avoid instability issues and be restrictive in high-performance applications. This paper presents a differential- and common-current (power)-based state-feedback control for BTB converters. This controller features a fast control of active and reactive powers, and a stiff regulation of the dc-link voltage. A theoretical analysis of the proposed controller along with a strategy for current limiting is presented. Its robustness was tested against variations of the filter parameters, the dc capacitance, the grid inductance, and the grid voltage values. The controller was experimentally validated under nominal operation, voltage sags, and connected to a weak grid by using a 15-kVA BTB converter in a laboratory test network. [ABSTRACT FROM AUTHOR]

Automated early detection and identification of switch faults are essential in high-voltage applications. Modular multilevel converter (MMC) is a new and promising topology for such applications. MMC is composed of many identical controlled voltage sources called modules or cells. Each cell may have one or more switches and a switch failure may occur in anyone of these cells. The steady-state normal and fault behavior of a cell voltage will also significantly vary according to the changes in the load current and the fault timing. This makes it a challenging problem to detect and identify such faults as soon as they occur. In this paper, we propose a real-time and highly accurate MMC circuit monitoring system for early fault detection and identification using adaptive one-dimensional convolutional neural networks. The proposed approach is directly applicable to the raw voltage and current data and thus eliminates the need for any feature extraction algorithm, resulting in a highly efficient and reliable system. Simulation results obtained using a four-cell, eight-switch MMC topology demonstrate that the proposed system has a high reliability to avoid any false alarm and achieves a detection probability of 0.989, and average identification probability of 0.997 in less than 100 ms. [ABSTRACT FROM AUTHOR]

For efficient power transfer in an inductive power transfer system, the primary coil, placed inside the charging pad, and the secondary coil, kept inside the vehicle pad, must be aligned correctly. Information about the real-time position of the electric vehicle (EV) with respect to the charging pad is required to aid the driver in the alignment of the two coils. This paper proposes a wireless LC-based scheme using three small sensing coils kept close to the primary coil, to detect the position of the EV. Each sensing coil has a capacitor connected to it, forming three LC tank circuits. The measurement circuit, which is connected to the secondary coil, measures the coupling coefficient between the secondary coil and each of the LC coils. Based on these values, the direction in which the EV should be driven to align the two coils is determined. This information is displayed to the driver. A prototype of the proposed scheme is designed and tested. Using the proposed scheme, the primary and the secondary coils are aligned correctly. This is verified by exciting the primary coil of the prototype by a power source at 50 kHz and measuring the induced voltage in the secondary coil, which is found to be the maximum when the two coils are aligned using the proposed scheme. [ABSTRACT FROM AUTHOR]

This paper presents a novel switch current stress reduction technique for a single switch boost-flyback high step up dc–dc converter. Coupled inductor-based converters do not have a sufficiently higher inductance value of their windings. This creates current surge during transient and steady state, which in turn increases current stress at main switch. To compensate this difficulty in coupled inductor-based boost flyback converter, an inductor–diode parallel combination has been connected in series with the switch. This technique increases the effective inductance of the coupled inductor primary winding during switch turn-on operation and helps to reduce current stress. Steady-state operating principle with the proposed technique is analyzed in continuous conduction mode. The current reduction technique is discussed with a proper mathematical derivation. To verify theoretical findings, simulation study is carried out in MATLAB/Simulink R2014b. Finally, a laboratory-based 40-W prototype converter is designed to show the effectiveness of the proposed switch current reduction technique. [ABSTRACT FROM AUTHOR]

Aluminum electrolytic capacitors (AECs) are connected in a bank to meet the requirement of capacitance, voltage, and current rating for dc-link of power electronic converters. The performance of capacitor bank deteriorates with time due to the degradation of AECs in the bank. Further, each AEC in the bank degrades differently based on its core temperature, which in turn depends on the current and its equivalent series resistance (ESR). Therefore, health monitoring of a bank would require monitoring of individual AECs in the bank. However, extending the available literature on health monitoring of an AEC to the capacitor bank would require voltage/current sensors for individual AECs. To address the aforementioned issue, this paper suggests a method to assess the health of individual AECs online in the bank without using sensors for each AECs. The proposed method involves estimation of current through each capacitor, which is used to determine the core temperature by using a thermal model of AEC. The core temperature is used for estimation of ESR and capacitance of each capacitor using physics-of-failure based degradation model. For the consistent matching of the degradation model to the actual degradation of the capacitor, the coefficients of the model are sequentially updated. For updating, an algorithm based on extended Kalman filter is used. The proposed scheme is experimentally validated on laboratory prototype of single-phase, grid-connected solar PV inverter under variable load conditions. [ABSTRACT FROM AUTHOR]

The nine-arm modular multilevel converter (9A-MMC) has been recently proposed as a reduced MMC topology variation for six-phase drive applications, with 25% reduction in the number of employed arms and associated components, compared to a standard dual three-phase MMC, however with a limited output voltage amplitude. This paper proposes a hybrid 9A-MMC comprised of half-bridge submodules (SMs) in both the upper and lower arms, and full-bridge SMs in the middle arms. By employing the negative-voltage state of the full-bridge SMs, the hybrid 9A-MMC avoids the limitations imposed on the dc-link voltage utilization, while achieving further reduction in the component count, compared to a standard 9A-MMC with identical half-bridge SMs. The operating principles of the proposed hybrid 9A-MMC are illustrated with mathematical analysis, whereas its characteristics are verified through both simulation and experimentation. An assessment of the proposed topology quantifying its employed components is also provided, in comparison to other MMC-based six-phase machine drives. [ABSTRACT FROM AUTHOR]

A new transformerless bidirectional buck-boost converter is proposed in this paper. The proposed converter has a simple circuit structure, low component count, low voltage stress on the power transistors, and a wide voltage gain range. This makes it applicable in the energy storage charge/discharge systems, such as electric vehicles (EV), microgrids and nanogrids with energy storage units, and uninterruptible power supplies. In addition, synchronous rectification between the complementary transistors is employed to improve the converter efficiency. A comprehensive analysis of the steady-state operation, small-signal model, component parameters design, and efficiency analysis of the proposed converter operating in a continuous conduction mode is given. Finally, a 1.6-kW scaled-down prototype was built using Silicon Carbide MOSFETS to validate the effectiveness and feasibility of the proposed converter. [ABSTRACT FROM AUTHOR]

In this paper, a new Lyapunov-based model predictive controller is proposed for a 7-level packed U-cell (PUC7) grid-connected inverter. A cost function of the proposed model predictive controller is designed from the system stability point of view, inspired by the Lyapunov control theory. The proposed controller eliminates the need for gains that are associated with cost function coefficients, as seen in classical model predictive control based controllers. Therefore, the control design problem is significantly simplified. In addition, the average switching frequency is also reduced, as shown in both simulation and experimental results, leading to a reduction in switching losses. Simulation and experimental tests, on a PUC7 lab prototype, demonstrate the excellent performance of the proposed control system, in terms of high disturbance rejection, robustness to parameter mismatches, and fast dynamic response. Such features qualify the proposed control strategy as a good candidate for grid-tied applications. [ABSTRACT FROM AUTHOR]

In this paper, several new coupled-inductor-based soft-switching dc–dc converters are proposed. These converters are obtained by changing the coupled branch of several existing dc–dc converters. Meanwhile they have similar characteristics to these existing converters, and provide more choices for the practical application. Then by applying an existing efficiency improvement method, which is used in the buck-type soft-switching converter, to all abovementioned converters, several new converters with efficiency improvement characteristics are obtained. This efficiency improvement method utilizes the low conduction performance of the transistor to reduce the loss. In addition, this method has the same control complexity to original topologies, because the auxiliary transistor has the same control timing to one of main transistors. The characteristic of new converters and efficiency improvement method are presented by analyzing two new topologies (boost-type converters). Finally simulation and experimental results are given and analyzed by designing a prototype. Based on these results, soft-switching conditions and efficiency improvement capability are verified. [ABSTRACT FROM AUTHOR]

The lack of dc fault clearance capability is a major obstacle that restricts the development of high-voltage direct current (HVdc) systems. Employing an active mechanical dc circuit breaker (M-DCCB) is an effective method to handle the dc fault. However, the existing active M-DCCBs can interrupt the fault current once but have problems in making the second interruption instantly in case of reclosing a permanent dc fault. In this paper, a novel topology of the active M-DCCB is proposed by inserting a precharged capacitor into a bridge formed by four spark gap switches. The operating strategy for the proposed M-DCCB is discussed to handle the dc faults. Its parameters, including the oscillation inductor and the oscillation capacitor, are determined by inequations derived from the requirements of dc fault interruption. The selection standard for the spark gap switch is set based on its breakdown characteristics. Finally, simulations are conducted to investigate the performance of the proposed M-DCCB. Results show that the capacitor can accumulate a sufficiently large reverse charge voltage automatically charged by the fault current. The proposed active M-DCCB topology and the dc fault handling strategy can interrupt the dc fault in HVdc power systems consecutively. [ABSTRACT FROM AUTHOR]

In this paper, a novel noncoupled inductor high voltage gain single-ended primary-inductor converter (SEPIC) is presented. The proposed converter has various advantages, such as lower voltage stress on the switches, noninverting output voltage, high efficiency, and high voltage gain. Also, the introduced converter has a continuous input current which makes it suitable for renewable energy and fuel cell applications. Moreover, high voltage gain is achieved without using any transformer and coupled inductor, thus there is not any voltage overshoot for the switches during the turn-off process. This effect allows low conduction losses by using lower voltage rating switches and also additional clamping circuit is not needed. The control system of the presented converter is simple and the converter can be easily controlled in continuous conduction mode mode operation. Because, the gating pulses for both of the switches are the same and wide output voltage range is achieved only by changing the duty cycle. Furthermore, the number of the components compared to the other noncoupled inductor, SEPIC-based converters which provide near voltage gain to the proposed converter, is reduced. The detailed operation of the introduced converter and design considerations are discussed. Experimental results are presented to verify the performance of the proposed dc–dc converter. [ABSTRACT FROM AUTHOR]

This paper presents an approach for dealing with the control of five-level, diode-clamped rectifiers. The control of such converters is challenging, as voltage balancing among capacitors is not a trivial task. Some of the existing approaches that cope with this problem use specific modifications of one of the traditional modulation techniques, such as using redundant vectors in space vector modulation (SVM). The main feature of the proposed technique is that part of the modulation is considered in the system equations and, in this way, the voltage balance can be solved designing a specific controller for this problem. As a result, several levels are used within a switching period. Furthermore, it is shown that the proposed approach hardly affects the control of active and reactive powers and total dc-link voltage in such a way that the well-known direct power control can be applied. As a consequence, the resultant modulation stage is simpler than other techniques based on, e.g., SVM. The effectiveness and good performance of the system under the proposed control approach are validated by both simulation and experimental results. [ABSTRACT FROM AUTHOR]

This paper presents a new approach to controlling and optimizing a single-stage boost-integrated full-bridge dc–dc converter for a stand-alone photovoltaic-battery-powered dc motor system by combining pulse-frequency modulation (PFM), pulsewidth modulation (PWM), and phase angle shift (PAS). Unlike most of the existing multiport dc–dc converters, which aim at regulating the output voltage (first- or second-quadrant operation), the dc motor load requires both voltage and current reversals (four-quadrant operation). The converter is able to perform three tasks simultaneously: maximum power point tracking (MPPT), battery charging/discharging, and driving the dc motor at variable speeds including bidirectional and stall motions. To achieve these control objectives, the boost inductor and the motor inductance operate in different modes such that PFM and PWM can be used to achieve MPPT and a wide motor voltage range, respectively. By properly adjusting the PAS of the duty cycles, the capacitor and battery rms current value can be reduced, while the operation of the converter remains unchanged, hence improving the conversion efficiency. Experimental results of a 26-W laboratory prototype converter confirmed the proposed design and operation and the efficiency improvement by 2–6%. [ABSTRACT FROM AUTHOR]

This paper presents a highly efficient 3.3-kW single-stage on-board charger (OBC). The proposed OBC consists of two interleaved cells sharing a full-bridge diode rectifier. Each cell is composed of an active clamp circuit and a series resonant circuit. The proposed OBC provides zero-voltage switching of all switches and reduces the reverse-recovery problem by zero-current switching of the output diodes. The interleaved technique maintains the proper power level with high efficiency. The proposed control algorithm enables power factor correction by the OBC without any auxiliary circuit and balances the input current between the two cells. In addition, the proposed converter requires no electrolytic dc-link capacitor, ensuring compact size and a long lifetime. Owing to these features, the proposed OBC efficiently outputs a high power factor over a wide power range and achieves reliability with a simply structured, single-power processing step. Therefore, the proposed OBC is potentially feasible for automotive applications. Finally, the theoretical analysis is confirmed in a 3.3-kW prototype and validated in experimental results. [ABSTRACT FROM AUTHOR]

In this paper, a new step-up dc–dc converter module that consists of three resonant submodules interconnecting with 1:1 turns ratio three-phase transformer and coupled current-fed voltage doubler modules is presented for medium voltage dc converter design in wind energy application. By utilizing step-up resonant circuits with three-phase transformer and combining it with a “multistring” inverter, the proposed circuit structure completely utilizes all the switching circuits to transfer power to the output. In addition, the proposed topology is able to achieve high voltage gain without using large turns ratio high frequency step-up transformers. Zero voltage switching turn-on and near zero current switching (ZCS) turn-off are maintained for all the switches. A modular 1.5 MW, 1 kV (dc-link), 20 kV (output) converter system is presented to validate the performance of the proposed circuit. Experimental results on a laboratory-scale 2.8 kW, 0.3 kV (dc-link), 6 kV (output), prototype are provided to highlight the merits of this work. Silicon Carbide (SiC) MOSFETs and SiC Schottky diodes are utilized in both designs. Results confirm that a peak efficiency of 97.6% is achieved in the prototype. [ABSTRACT FROM AUTHOR]

In this paper, a novel current fed hybrid dual active bridge dc–dc converter is proposed, which is suitable for a low-voltage fuel cell power conditioning system. The high-frequency input current ripple can be reduced to minimum because the input side switches are always switched at 50% duty cycles in spite of the fuel cell voltage and the load variation. Notch filter is used in the voltage feedback path to reduce the low-frequency input current ripple when interfaced with a single-phase inverter load. All of the power devices can achieve zero voltage switching by the proposed control strategy. The mode analysis, the operation principle, zero-voltage switching (ZVS) conditions, and parameter design are given in this paper. A 1 kW prototype has been fabricated to verify the effectiveness of the proposed converter and control strategy. [ABSTRACT FROM PUBLISHER]

This paper deals with a hybrid fault-tolerant converter topology. It is performed through the connection of a classical three-phase three-level neutral-point-clamped (3L-NPC) converter with a fourth three-level flying capacitor (3L-FC) leg. The 3L-FC leg actively balances the 3L-NPC neutral-point voltage. For normal operation mode, this paper proposes a mathematical design of the filter needed to connect these two different topologies. Experimentally, and thanks to the already existing decoupling capacitors of the 3L-NPC converter, this filter requires the addition of only one low size inductance. When one fault of the power switch of the 3L-NPC occurs, this paper proposes a hardware reconfiguration technique based on only two fuses and one thyristor per leg allows a safe postfault operation recovery. This is achieved thanks to a simple fault-detection method and a new technique that combines fault leg isolation and corresponding phase postfault connection to the neutral point. Also, a dedicated field-programmable gate array (FPGA)-based control of the reconfigured converter is synthetized to ensure power system availability under fault operation mode. The converter fault-tolerant capabilities are addressed through simulation results and original overall experimental validations of the fault detection and isolation and the postfault operation steps, carried out on a 15-kW prototype converter. [ABSTRACT FROM AUTHOR]

Resonant modular multilevel converters (RMMCs) have been proposed for high-voltage dc–dc applications. Using different modulation strategies, RMMC operates in different modes and achieves flexible step ratio. To provide a comprehensive study of RMMCs, this paper presents the modulation method achieving a wide range of step ratio with the ability of inherent-balancing. The conditions for guaranteeing the inherent-balancing ability are provided. The operation principle and performance of the RMMC are presented in this paper, which have been explored in a case study. The experimental results are obtained from a bench-scale setup, which have verified the theoretical analysis. [ABSTRACT FROM PUBLISHER]

In order to provide a constant current to the Light-emitting diodes (LEDs) and to minimize the size and cost of the driver circuit in ac/dc offline LED drivers, electrolytic capacitors are conventionally used due to their high energy density and low cost. However, electrolytic capacitors are sensitive to operating temperature and have much shorter lifetime than the LED semiconductor devices. This paper proposes an improved control scheme that is capable to control the output LED current and regulate the dc-link capacitor's energy simultaneously for a family of single-stage soft-switched high power factor LED driver topologies. Each of these topologies consists of an integrated power factor correction (PFC) circuit. Due to the proposed controller's capability to control the LED current directly via variable frequency control and the dc-link capacitor's voltage via duty ratio control, the required energy storage capacitance can be significantly reduced, thereby allowing small size film capacitor to be used as the energy storage capacitor. Simulation results are provided on two different LED driver topologies, one with an integrated boost PFC stage and the other one with an integrated buck–boost PFC stage, to verify the performance of the proposed control scheme. Experimental results are also been provided on a 12-W prototype to highlight the merits of this paper. [ABSTRACT FROM PUBLISHER]

Condition monitoring of aluminum electrolytic capacitors (AECs) is essential for predictive maintenance of power electronic converters. The AEC is considered at the end of its life when its capacitance or equivalent series resistance (ESR) reaches corresponding critical values. In the literature, it is found that either of these parameters may reach its critical limit depending on the operating conditions and applications. However, most of the existing health monitoring techniques of the AEC in dc–dc converters are based on the estimation of ESR. To address the aforementioned issue, this paper proposes to estimate the low-frequency impedance of the AEC, which is dominated by its capacitance value, thereby allowing health monitoring based on the capacitance value. The technique is based on injection of a low-frequency current ripple into the AEC using duty ratio control of the dc–dc converter. The parameters of new and aged capacitors are experimentally obtained at various temperatures and are used to establish the failure criteria. Furthermore, the proposed method is applicable for both the continuous conduction mode and the discontinuous conduction mode (DCM) of operation. For DCM operation, a sampling instant to recover a low-frequency waveform is suggested based on mathematical analysis. Detailed simulation studies are performed and results are included in this paper. Experimentation is carried out on a dc–dc boost converter integrating solar photovoltaic with the dc system. Experimental results are found to be in agreement with simulation results. [ABSTRACT FROM PUBLISHER]

Synchronverters are inverters that mimic the behavior of synchronous generators. In this paper, we propose five modifications to the synchronverter algorithm from the paper “Synchronverters: Inverters that mimic synchronous generators,” (IEEE Trans. Ind. Electron., vol. 58, no. 4, pp. 1259–1267, Apr. 2011), to improve its stability and performance. These modifications are implemented in software and do not require any changes in the inverter hardware. The first two modifications concern the control of the virtual field current in the synchronverter so that it is more robust to faults. We prove the stability of the grid-connected synchronverter with this improved field current controller. The third modification is to increase the effective size of the filter inductors virtually. This is motivated using results from the stability analysis of a constant field current synchronous generator connected to an ac power grid and also by practical considerations. Simulations and experiments show that this leads to a much better response to changes in grid frequency, voltage, or to imbalance in the grid. The fourth modification is to change the formula for the (virtual) nominal active mechanical torque to take into account the (virtual) losses in the output impedance of the converter. This makes the tracking of the desired active power much more accurate. The fifth modification is to introduce virtual capacitors in series with the inverter outputs to filter spurious dc components from the current supplied to the grid. [ABSTRACT FROM PUBLISHER]

Multilevel converters have gained popularity in both medium voltage and low voltage applications. To find out the connections between various multilevel voltage-source converter topologies and to reveal how to obtain new topologies, this paper has presented four methods to derive multilevel converter topologies. Many existing topologies as well as new topologies can be derived with the methods presented in this paper. The fundamental characteristics of the multilevel converters which determine their usability such as dc-link neutral point voltage balancing and flying capacitor voltage control are also investigated in this paper with a mathematical model and an example. It is expected that more new topologies will be invented based on the work in this paper for emerging applications. [ABSTRACT FROM AUTHOR]

This paper proposes unified non-inverting and inverting ac–ac converter (UNI-AC) using pulse width modulation (PWM) for the utility voltage compensation. It offers four effective switching states to regulate the output voltage in bipolar manner, facilitating versatile modes of operation with different number of switching states being modulated. Each mode of the proposed UNI-AC is able to compensate both the grid voltage sag and swell problems due to its bipolar voltage gain. The operational principle and comparison for all these modes are investigated in details. Also, the UNI-AC is reversible and compatible with full range of power factor. Other technical merits offered by the proposed approach include the compact hardware installation, reduced switch voltage stress (also low dv/dt) and decreased control complexity. Detailed analysis and experimental verification are presented in this paper. [ABSTRACT FROM AUTHOR]

In this paper, a new soft switching flyback dc–dc converter with a simple zero-voltage and zero-current switching (ZVZCS) cell is proposed. The auxiliary resonant cell consists of one switch, one diode, one inductor, and two capacitors. It provides ZVZCS not only for the main switch but also for the auxiliary switch at both turn-on and turn-off times. In addition, all the auxiliary diodes and body diodes of the switches operate under full ZVZCS except the output diode which turns off only with zero current switching. This soft switching technique makes the proposed converter have less switching losses which leads the converter to operate in higher frequencies and efficiency. Another outstanding feature of the proposed converter is using the auxiliary resonant cell out of the main power path to have lower voltage stress on the switches. In this paper, pulse width modulation (PWM) is employed to control the main switch. A detailed mode analysis of the proposed converter operation is presented along with design procedure. Finally, the accuracy performance of the converter is verified through a 60 W experimental prototype results. [ABSTRACT FROM AUTHOR]

In this paper, an electrolytic capacitor-less ac–dc light-emitting diode (LED) driver, consisting of a power factor correction (PFC) converter and a buck/boost bidirectional converter, is investigated. The buck/boost bidirectional converter is connected in parallel with the output of the PFC converter and serves to absorb the second harmonic current in the PFC output current, leaving only a dc component to drive the LEDs. This paper proposes an adaptive voltage control scheme for the storage capacitor in the buck/boost bidirectional converter to make the storage capacitor voltage adaptively decrease as the load becomes lighter. Hence, the power losses of the buck/boost bidirectional converter could be reduced at light load. Experimental results are provided to verify the effectiveness of the proposed control scheme. [ABSTRACT FROM PUBLISHER]

In this paper, a new topology for half-bridge Z-source inverter is proposed. The proposed topology has only one impedance network. Unlike to the conventional half-bridge inverter, the proposed topology can provide zero voltage level at the output. It also increases output voltage level and stabilizes it in the desired value. Capacitor voltage stress in the proposed topology is low, and, therefore, nominal voltage of capacitor and cost decreases. In this paper, the steady-state analysis of the proposed inverter in two new operations which are named synchronous operation of diodes and asynchronous operation of diodes is conducted based on mathematics calculations. A method to obtain high-voltage gains by cascading the Z-network and combining middle inductors is presented that leads to cost, size, and weight reduction. Comparison among the proposed converter with conventional ones shows its excellent performance. The experimental results have good agreement with analytical analysis for the proposed topology. [ABSTRACT FROM PUBLISHER]

In a conventional finite control set model predictive control (FCS-MPC) formulation, active and reactive power control loops rely on the predictive controller, whereas the dc-bus voltage is usually governed by a PI-based control loop. This originates from fact that the dynamic equations for describing the predictions of these variables are heavily coupled. In this paper, a cascade-free FCS-MPC for single-phase grid-connected power converters is presented. The proposed control algorithm is formulated in terms of established dynamic references design, which was originally proposed to directly govern active and reactive power, and dc-voltage in three-phase power converters. In this paper, the dynamic reference design concept is extended to control single-phase grid-connected power converters. The proposed control algorithm does not use instantaneous ac-power calculations; instead, it directly formulates the optimal control problem on the grid-current in the original stationary reference frame. The experimental results obtained with a single-phase grid-connected neutral point clamped (NPC) converter confirm a successful design, where system constraints, e.g., maximum power and weighted switching frequency, are easily taken into account. [ABSTRACT FROM PUBLISHER]

A quasi-Z-source modular cascaded converter (qZS-MCC) is proposed for dc integration of high-power photovoltaic (PV) systems. The qZS-MCC comprises series-connected front-end isolated qZS half-bridge (HB) dc–dc converter submodules (SMs). With the front-end isolation, the qZS-MCC achieves high-voltage dc capability, while maintaining modularity and PV panel grounded. The post-stage qZS-HB handles the PV voltage and power flows, dc-link voltage balance, and output-series power integration. Whereas, the front-end isolation converters of all SMs perform a constant duty cycle, lowing the control complexity. There is no double-line-frequency power flowing through the dc-side PV panels, qZS inductors, and qZS capacitors in the qZS-MCC, so small qZS impedance is possible compared to the existing qZS cascaded multilevel inverter. The configuration, operating principle, power loss evaluation, and passive components design of the proposed system are investigated in this part of the paper. The system control, modeling, and corresponding verifications are stated in Part II of this paper. [ABSTRACT FROM PUBLISHER]

To improve the power factor and reliability for medium/high-power supply, a three-phase single-stage ac–dc converter based on magnetic-combination transformer with power factor correction (PFC) function is presented in this paper. According to the three-phase instantaneous power balance principle and the concept of the magnetic-flux superposition, a novel magnetic-combination transformer is proposed, which can make three-phase symmetrically and sinusoidally fluctuant power add to be constant. Therefore, the induced voltage of the secondary winding is constant. To realize sinusoidally fluctuant power in the input stage, dc-link filter capacitance can be reduced to a several-microfarad level. Single-stage PFC function, no electrolytic capacitor, and constant output voltage can be realized in the converter. The principle and the structure of the novel magnetic-combination transformer are analyzed in detail in this paper. Simulation and experimental results are presented to verify the feasibility of the proposed converter. [ABSTRACT FROM AUTHOR]

Zero-common-mode-voltage (CMV) operation of multilevel inverters results in reduced dc-bus utilization and reduced linear modulation range. In this paper, a method to increase the linear modulation range for zero-CMV operation without increasing the dc-bus voltage using a cascaded multilevel inverter with a single dc supply is presented. Using this method, the peak fundamental output voltage can be increased from 0.499 to 0.637  \textV\text{dc} with zero CMV inside the linear modulation range. Also, various pulse width modulation (PWM) switching sequences are analyzed in this paper, and the PWM sequence that gives minimum current ripple is used for the zero-CMV operation of the inverter. The inverter topology with single dc supply is realized by cascading a two-level inverter with two floating-capacitor-fed full-bridge modules. Simulation and experimental results for steady-state and dynamic operating conditions are presented to validate the proposed method. [ABSTRACT FROM AUTHOR]

High-voltage pulse-generators can be used effectively for bacterial decontamination in water treatment applications. Applying a pulsed electric field to the infected water sample guarantees killing of harmful germs and bacteria. In this paper, a modular high-voltage pulse-generator with sequential charging is proposed for water treatment via underwater pulsed streamer corona discharge. The proposed generator consists of series-connected modules similar to an arm of a modular multilevel converter. The modules’ capacitors are charged sequentially from a relatively low-voltage dc supply, then they are connected in series and discharged into the load. Two configurations are proposed in this paper, one for low repetitive pulse rate applications, and the other for high repetitive pulse rates. In the first topology, the equivalent resistance of the infected water sample is used as a charging resistance for the generator’s capacitors during the charging process. While in the second topology, the water resistance is bypassed during the charging process, and an external charging resistance with proper value is used instead. In this paper, detailed designs for the proposed pulse-generators are presented and validated by simulation results using MATLAB. A scaled down experimental setup has been built to show the viability of the proposed concept. [ABSTRACT FROM AUTHOR]