Search

This paper deals with the development and implementation of an on-line technique for the identification of the stator resistance and permanent magnet flux linkage on three-phase, open-end winding, permanent magnet synchronous motor (PMSM) drives. The stator resistance and permanent magnet flux linkage are independently determined by exploiting a special current vector control strategy, which holds one of the phase currents at zero while suitably modifying the other two in order to keep the magnetomotive force unchanged. As will be demonstrated, no additional sensors or special tests are required by the proposed technique; moreover, motor electrical parameters can be on-line estimated in a wide operating range, avoiding any detrimental impact on the torque capability of the PMSM drive. Finally, the electrical machine thermal status can be also estimated from obtained values of the stator resistance and permanent magnet flux linkage. [ABSTRACT FROM AUTHOR]

Model-predictive current control (MPCC) is widely recognized as a high-performance control strategy of permanent magnet synchronous machine (PMSM) drives due to its quick response and simple principle. It uses a cost function to select the best voltage vector minimizing the current error between the reference value and the feedback value. However, as only one voltage vector is applied during one control period, it fails to give satisfactory performance due to the limited voltage vectors, especially in the case of two-level converters. This paper proposes an improved MPCC strategy for PMSM drives, which first estimates the back electromotive force (EMF) based on the past value of stator voltage and currents and then applies the estimated EMF in the stator current prediction. To achieve steady-state performance improvement, a null vector along with the active vector obtained from conventional MPCC is applied during one control period. Two methods are proposed to achieve optimal vector selection and vector duration. The first one requires six predictions and the calculation of current differentiation, while the second one only requires one prediction to obtain the best voltage vector and its optimal duty can be obtained in a very efficient way. The proposed methods are comparatively studied and compared to conventional MPCC and deadbeat control with space vector modulation. Both simulation and experimental results confirm the effectiveness of the proposed methods in achieving good steady-state performance while maintaining quick dynamic response. [ABSTRACT FROM AUTHOR]

This paper describes the design procedure followed to realize a high-speed synchronous reluctance machine for aeronautical application. The attention is mainly focused on the rotor design that is the most critical part of any synchronous reluctance machine; in particular for high-speed applications. After a preliminary optimization of the rotor geometry, a multiphysical design that considered mechanical, thermal, and electromagnetic properties was developed. The main steps of the design procedure together with an extensive analysis of the final design are presented here. Two prototypes have been realized using different rotor lamination materials in order to validate the design procedure. [ABSTRACT FROM PUBLISHER]

The use of an extended Kalman filter (EKF) as a nonlinear speed and position observer for permanent-magnet synchronous motor drives is a mature research topic. Notwith-standing, the shift from research prototype to a market-ready product still calls for a solution to some implementation pitfalls. The major and still unsolved topic is the choice of the EKF covariance matrices. This paper replaces the usual trial-and-error method with a straightforward matrices choice. These matrices, possibly combined with a novel self-tuning procedure, should put the EKF drive much closer to an off-the-shelf product. The proposed method is based on the complete normalization of the EKF algorithm representation. Successful experimental results are included in the paper. [ABSTRACT FROM AUTHOR]

This paper proposes a novel low-cost control strategy of gearless traction permanent-magnet synchronous machines for direct-drive elevator applications. It can improve robustness of the weight-sensorless traction machine system installed with an ordinary incremental encoder. In order to improve the riding comfort for the passengers during brake releases, a novel starting torque compensation strategy without a weight transducer is presented. After analyzing the dynamic characteristics and the friction torque of the elevator traction system, two starting torque compensation methods based on the dichotomy and the staircase method are proposed for the weight-sensorless elevator applications. This way, electromagnetic torque can be generated to balance the load torque, and sliding can be prevented when the elevator brake releases during the starting operation. To achieve the current vector decoupling control for the traction machine installed with an incremental encoder, the initial rotor position estimation at standstill based on a hybrid signal injection method is adopted. First, a high-frequency oscillating sinusoidal voltage signal is injected to obtain the magnetic pole position. Then, two pulse voltage vectors are injected in the positive and negative directions to identify the magnet polarity. The experimental results demonstrate the feasibility of the proposed control strategy with an 11.7-kW traction machine. [ABSTRACT FROM PUBLISHER]

Over the last few decades, the production of liquefied natural gas (LNG) has been pushing the development of electric drives with increasingly high power ratings, up to several tens of megawatts. A consolidated technology in this field entails dual-star two-pole synchronous motors fed by load-commutated inverters with supply frequencies between 50 and 80 Hz. This paper presents a novel drive concept for very high-power and high-performance LNG applications based on a 45-MW four-pole 100-Hz quadruple-star synchronous motor supplied by four pulsewidth modulation multilevel voltage source inverters. The genesis, development, and industrial implementation of this new design concept are outlined. Full-load drive system testing and commissioning results are presented which successfully validate the proposed solution. [ABSTRACT FROM AUTHOR]