Search

The nonresonant single-phase dual-active-bridge (NSDAB) dc–dc converter has been increasingly adopted for isolated dc–dc power conversion systems. Over the past few years, significant research has been carried out to address the technical challenges associated with modulations and controls of the NSDAB dc–dc converter. The aim of this paper is to review and compare these recent state-of-the-art modulation and control strategies. First, the modulation strategies for the NSDAB dc–dc converter are analyzed. All possible phase-shift patterns are demonstrated, and the correlation analysis of the typical phases-shift modulation methods for the NSDAB dc–dc converter is presented. Then, an overview of steady-state efficiency-optimization strategies is discussed for the NSDAB dc–dc converter. Moreover, a review of optimized techniques for dynamic responses is also provided. For both the efficiency and dynamic optimizations, thorough comparisons and recommendations are provided in this paper. Finally, to improve both steady-state and transient performances, a combination approach to optimize both the efficiency and dynamics for an NSDAB dc–dc converter based on the reviewed methods is presented in this paper. [ABSTRACT FROM AUTHOR]

This paper proposes a new control strategy of microgrids for the improved voltage quality. In the existing control techniques, the droop control is commonly adopted as a decentralized power sharing method at the cost of voltage deviations. Besides, the conventional cascaded control featuring relatively slow dynamic response shows difficulties in handling the fluctuation of renewable energy outputs, leading to further voltage quality deterioration. In this paper, an advanced model predictive power control strategy by considering the battery constraints is proposed for the bidirectional dc–dc converters to smooth the solar photovoltaic (PV) outputs and stabilize the dc-bus voltages. A model predictive voltage control scheme taking into account the voltage changing trend is then developed to control the distributed inverters to improve the output ac voltages. Furthermore, a washout-filter-based power sharing approach with the plug-and-play capability is adopted to achieve a proper load sharing among parallel inverters and mitigate the voltage deviation. The proposed control strategy is numerically simulated in MATLAB/Simulink and experimentally verified by hardware-in-the-loop tests under the condition of fluctuating PV outputs and variable power demands. (This paper is accompanied by a video showing the hardware-in-the-loop test.) [ABSTRACT FROM AUTHOR]

Cascaded-connected string converter is an effective way to directly interconnect distributed low-voltage dc sources into higher voltage ac grids. When this system is switched to islanding operation, an important task is to obtain decentralized power sharing among power cells according to the corresponding dc source power capacity, and at the same time, maintaining a good regulation of supply voltage quality to local critical loads. In this paper, a hierarchical control approach is proposed to simultaneously realize the abovementioned two tasks. First, the central controller at point of common coupling (PCC) is responsible for supply voltage magnitude and frequency deviation suppression and it also distributes the key control signals to all power cell local controllers with only low bandwidth communications. At the same time, a modified inverse power factor droop regulator with adjustable offset is adopted by each power cell. As the offset is relevant to the PCC load power factor and the state of charges of power cell backstage batteries, it can easily obtain decentralized proportional power sharing. The proposed system and the control strategy are compared with the conventional parallel converters-based system and the potential applications of the system are also given in this paper. [ABSTRACT FROM AUTHOR]

An important issue in the photovoltaic (PV) power generation systems is the massive amount of heat wasted by PV modules/panels. For the first time, this paper provides a new solution to recover a portion of the mentioned waste heat by utilizing a proposed electrochemical heat engine. A thermally regenerative electrochemical cycle (TREC) system has been designed, constructed, and embedded in a PV power generation system including a 200-W PV module to harvest the waste heat of its PV module, so a PV-TREC hybrid system has been organized and built. The hot cell of the TREC system has been positioned in direct contact with the backside of the PV module, and the cold cell is in direct contact with a heat sink located in the shade of the PV module. Experimental verifications demonstrate that the proposed TREC system efficiently converts the waste heat into electric power ranging from 0.1 to 54.5 W. In this manner, up to 6% of the waste heat of the PV module is recovered. It also substantiated that the daily energy efficiency of the PV-TREC hybrid system is improved by 27.5% compared to a usual PV system, and this is the main contribution and novelty of this paper. [ABSTRACT FROM AUTHOR]

In this paper, a new class of bidirectional partial-resonance power converters is presented. The proposed family can be configured to interface single- or multi-port dc, single- or multi-phase ac systems at input-side and/or output-side. The proposed family offers a very modular structure, which can lead to cost reduction from a common designed module. In this converter, which accomplishes power conversion in a single stage, a small inductor placed in series with the input and output switch-bridges forms the link. This small link inductor is responsible for transferring power between different ports of the system. The proposed topologies can operate in buck, boost, and buck–boost modes of operation to step up and/or step down the voltage. In buck–boost mode of operation, the converter is controlled such that the power is entirely transferred through the link inductor; whereas, in buck or boost modes of operation only a fraction of the power is transferred through the link inductor, and the remaining power is directly transferred from input phases to the output phases. Galvanic isolation, which is typically a prominent factor contributing to power density of a converter, can be provided by means of a compact and lightweight single-phase high-frequency transformer added to the link. In comparison with earlier generations of partial-resonance inductive-link power converters, in the proposed converter, the level of link peak current and consequently power-loss, as well as voltage and current stress of switches are dramatically decreased. A very small film capacitor can be placed in parallel with the link inductor to facilitate zero-voltage-switching (ZVS) operation for all the switches/diodes. Apart from increasing the overall efficiency, minimized dv/dt stress and improvement in power density are achieved by adding the link capacitor. The proposed converter employs four-quadrant switches, i.e., bidirectional-conducting bidirectional-blocking switches, and charges the link inductor in both positive and negative directions in each cycle. In view of this, better utilization of the link inductor and lower total harmonic distortion (THD) are offered. Furthermore, two distinct switching algorithms are developed for the proposed family of converters. In this paper, the detailed behavior of the proposed family is investigated analytically, and simulation and experimental results are presented to evaluate the performance and effectiveness of the proposed converter. A low-power proof-of-concept prototype with input voltage of 59 V/161 V, load voltage of 178 V/73.5 V, maximum switching frequency of 4.9 kHz/3.65 kHz at 215 W/450 W in a step-up/step-down operation is considered for the experimental verification. [ABSTRACT FROM AUTHOR]

This paper describes a dc-link voltage control method of a single-phase back-to-back cascaded H-bridge inverter (SBCI) for a medium-voltage motor drive system. The main advantage of the SBCI topology over the conventional regenerative cascaded H-bridge topology with a three-phase active front-end (AFE) is a simple system structure, which is composed of an input transformer, a power cell, a current sensor, etc. However, the challenging points of the SBCI are larger voltage ripple in the dc-link capacitor and imbalance of dc-link voltages of each phase. The asymmetric dc-link voltage of each power cells could cause unstable operation such as over-modulation due to the lack of the dc-link voltage of a particular phase and result in over-voltage or under-voltage faults. In this paper, the control strategy of the dc-link voltage for the SBCI that uses the negative-sequence voltage of the converter is described. The proposed control method is verified with a computer simulation whose target is a 6.6-kV–1.25-MW medium-voltage drive system. Also, through the experimental setup with the prototype SBCI whose power rating is 16.2 kVA, the dc-link voltage of each AFE has been controlled within a 0.5% error of its reference value at the full load. [ABSTRACT FROM AUTHOR]

The instantaneous output power of the two-stage single-phase grid-connected photovoltaic (PV) inverter pulsates at twice the line frequency ($2f_{{\text{o}}}$), generating second harmonic current (SHC) in the front-end dc–dc converter and PV panel, which will affect the maximum power point tracking operation and deteriorate the overall conversion efficiency. The generating mechanism of the SHC is analyzed in this paper and it is pointed that in order to eliminate the SHC in the front-end dc–dc converter and PV panel, the voltage loop gain of the front-end dc–dc converter should be high enough at $2f_{{\text{o}}}$. Since there is a −180° phase abrupt at the resonant frequency of the input side filter capacitor and the inductor, the system may be unstable. To cope with this problem, the inductor current feedback active-damping scheme (ADS) is adopted. For further improving the loop gain at $2f_{{\text{o}}}$ , proportional–integral–resonant regulator with ADS (PIR + ADS) is proposed in this paper. Besides, a step-by-step closed-loop parameters design method is presented. Finally, a 3-kW two-stage single-phase grid-connected PV inverter has been fabricated and tested, and the experimental results verify the feasibility of the proposed control schemes. [ABSTRACT FROM AUTHOR]

The photovoltaic (PV) output voltage varies over a wide range depending on operating conditions. Thus, the PV-connected converters should be capable of handling a wide input voltage range while maintaining high efficiencies. This paper proposes a new series resonant dc–dc converter for PV microinverter applications. Compared with the conventional series resonant converter, a dual-mode rectifier is configured on the secondary side, which enables a twofold voltage gain range for the proposed converter with a fixed-frequency phase-shift modulation scheme. The zero-voltage switching turn-on and zero-current switching turn-off can be achieved for active switches and diodes, thereby, minimizing the switching losses. Moreover, a variable dc-link voltage control scheme is introduced to the proposed converter, leading to a further efficiency improvement and input-voltage-range extension. The operation principle and essential characteristics (e.g., voltage gain, soft-switching, and root-mean-square current) of the proposed converter are detailed in this paper, and the power loss modeling and design optimization of components are also presented. A 1-MHz 250-W converter prototype with an input voltage range of 17–43 V is built and tested to verify the feasibility of the proposed converter. [ABSTRACT FROM AUTHOR]

One promising topology for solid state transformer (SST) is a modular multilevel cascaded converter, in which submodule is composed of dual active bridge (DAB) and H-bridge. For SST application in PV system, the efficiency could be severely affected especially for DAB due to the wide voltage and power range of PV panels. Thus, the motivation of this paper is to deal with the control strategy to improve DAB efficiency inside SST for PV application. Instead of utilizing time-domain based analysis method, which requires complex modeling process, this paper models DAB under frequency domain by fully considering the effect of both fundamental and harmonic frequency component. To achieve high efficiency operation, a multiorder reactive-current suppression (MRS) strategy is proposed by controlling phase shift angle as well as the duty cycles of primary and secondary side H-bridges. In terms of DAB controller design inside SST, the small signal model under MRS is established and a notch filter is implemented to suppress the second order line frequency fluctuation in the control loop. Finally, a 10 kV/1 MW SST prototype is introduced along with the system control structure and implementation method. The experiment of the submodule and SST confirms the effectiveness of proposed method. [ABSTRACT FROM AUTHOR]

This paper presents a novel bidirectional series resonant converter for energy storage systems (ESS). Conversion between a dc energy storage device and an ac grid has grown in importance because of the renewable energy generators and ESS used in microgrids, which usually use batteries or supercapacitors as storage devices in order to provide different services and improve the quality and reliability of the grid. This novel converter avoids the need to have two converting stages: one for converting the energy from the storage device to a regulated dc value, and the other for converting the regulated dc to the ac output. Conversion occurs via a modified dc/dc dual-bridge series resonant converter. The output bridge of the converter is attached to the input bridge through a resonant branch and a high frequency (HF) transformer, and it is also attached to the ac link through an output filter. Therefore, two ac power signals are mixed in the output bridge: a HF signal, which maintains the dc link capacitor voltage, and a low frequency power signal, which transfers energy to the grid. This paper details the different working modes of the converter and presents a 3000 W prototype that validates the design. [ABSTRACT FROM AUTHOR]

A modular multilevel converter (MMC) is regarded as a promising topology in high-voltage direct current systems. However, the MMC consists of numerous submodules (SMs) and switching devices, which lead to a considerable switching loss, and increased cost and size of the heat sink. To mitigate these issues, this paper presents a novel modulation method composed of fundamental frequency modulation (FFM) and multicarrier-based sinusoidal pulsewidth modulation schemes. The main purpose of this modulation method is the reduction of switching loss while maintaining good harmonic performance. However, the FFM scheme leads to the unbalanced capacitor voltage of each SM in the MMC. Accordingly, this paper additionally proposes the rotation method and selective voltage balancing control for SMs to ensure effective performance of the method. Simulation and experimental results verify the effectiveness and performance of the proposed modulation scheme through switching loss and spectral analyses. [ABSTRACT FROM AUTHOR]

The three-phase dual active bridge (3p-DAB) converter is a promising topology for high power dc–dc conversion due to advantages of bidirectional power flow, inherent soft-switching capability, and reduced filter volume. This paper presents comprehensive analysis of the duty cycle control (DCC) for optimizing the performance of the 3p-DAB. Based on DCC, an optimized modulation strategy is proposed to minimize the conduction losses of the 3p-DAB in the whole load range. The proposed modulation strategy extends the soft-switching range of the 3p-DAB with large voltage variations simultaneously. It is established through loss analysis that the proposed modulation strategy boosts the efficiency of the 3p-DAB, especially at low loads. When the duty cycles change fast as a result of the abruptly changed transmission power, the transformer currents can become unbalanced, leading to the magnetic bias and oscillations in dc currents. This paper further proposes a fast transient current control (FTCC) method for the 3p-DAB with variable duty cycles. The FTCC enables the converter to transfer from one steady state to another within about one-third switching period, hence balancing the transformer currents rapidly and avoiding oscillations in dc currents. Finally, experimental results verify the outstanding performance of the proposed modulation strategy and FTCC method. [ABSTRACT FROM AUTHOR]

In data center and telecommunication power supplies, the front-end dc–dc stage is required to operate with a wide input voltage range to provide hold-up time when ac input fails. Conventional LLC converter serving as the dc–dc stage is not suitable for this requirement, as the normal operation efficiency (at 400 V input) will be penalized once the converter is designed to achieve high peak gain (wide input voltage range). This paper examined the operation of the LCLC converter and revealed that the LCLC converter could be essentially equivalent to a set of LLC converters with different magnetizing inductors that are automatically adjusted for different input voltages. In nominal 400 V input operation, the LCLC converter behaves like an LLC converter with large magnetizing inductor, thus the resonant current is small. In the hold-up period, when the input voltage reduces, the equivalent magnetizing inductor will reduce together with switching frequency reducing, thus the converter achieves high peak gain. In this paper, a new design methodology is also proposed to achieve optimal utilization of the two resonant capacitors for high power application. To verify the effectiveness of the LCLC converter for hold-up operation, comprehensive analysis has been conducted; a detailed step by step design example based on capacitor voltage stress is introduced; an experimental LCLC prototype optimized at 400 V, with input voltage range of 250–400 V and 12 V/500 W as output has been presented. [ABSTRACT FROM AUTHOR]

A single-stage three-phase ac–ac converter benefiting from a high-frequency alternating link voltage is proposed in this paper. In this converter, a very small film capacitor can transfer the energy from the input to the output, owing to the high-frequency alternating voltage of the link. This eliminates the need for large electrolytic capacitors that are typically used in dc-link ac–ac converters. Moreover, a compact high-frequency transformer at the link can replace the bulky low-frequency transformers, in case isolation is required. These features increase the power density as well as reliability of the proposed converter in comparison with the conventional dc-link converters. The number of required switches in the proposed converter is 12, which is less than the number of switches needed in matrix converters, leading to lower switching and conduction losses. Despite being single-stage, the proposed ac–ac converter is capable of both stepping up and stepping down the voltage and also frequency transformation. This eliminates the need for using cascaded power converters. In this paper, the operation principles of the proposed ac–ac converter are investigated, and variable switching frequency and fixed switching frequency control methods for operating this converter are introduced. The performance of the converter is verified through simulation and experiment. [ABSTRACT FROM AUTHOR]

In this paper, a new structure for a nonisolated boost dc–dc converter is proposed. The proposed converter generates higher voltage gain than some conventional nonisolated boost dc–dc converters. In this paper, the voltage and current equations of the elements and voltage gain in continuous conduction mode and discontinuous conduction mode are extracted. Then, the critical inductance converter is extracted and the current stresses in the switches are calculated. To achieve high voltage gain, a generalized structure based on the proposed structure generates for dc–dc converters. Meanwhile, the root mean square current relations of devices are obtained for an extended structure. Finally, the results of PSCAD/EMTDC software and laboratory prototype are used to reconfirm theoretical concept. [ABSTRACT FROM AUTHOR]

This paper proposes a new load impedance specification for multistage dc power conversion systems. The proposed specification avoids drawbacks of the existing specifications, such as the lack of explicit connections to the dc-link dynamics and the unnecessary conservativeness. The new specification offers a direct command/supervision of the frequency- and time-domain dynamics of the intermediate dc link, while being less conservative than the existing specifications. This paper also presents procedures for redesigning ill-conditioned load impedances to comply with the specification. The validity and utility of the proposed specification are demonstrated using an experimental two-stage dc power conversion system. [ABSTRACT FROM AUTHOR]

In this paper, a high step-up quasi-Z Source (QZS) dc–dc converter is proposed. This converter uses a hybrid switched-capacitors switched-inductor method in order to achieve high voltage gains. The proposed converter have resolved the voltage gain limitation of the basic QZS dc–dc converter while keeping its main advantages, such as continuous input current and low voltage stress on capacitors. Compared to the basic converter, the duty cycle is not limited, and the voltage stress on the diodes and switch is not increased. In addition to these features, the proposed converter has a flexible structure, and extra stages could be added to it in order to achieve even higher voltage gains without increasing the voltage stress on devices or limiting the duty cycle. The operation principle of the converter and related relationships and waveforms are presented in the paper. Also, a comprehensive comparison between the proposed and other QZS based dc–dc converters is provided which confirms the superiority of the proposed converter. Simulations are done in power systems computer aided design (PSCAD) in order to investigate the maximum power point tracking (MPPT) capability of the converter. In addition, the valid performance and practicality of the converter are studied through the results obtained from the laboratory built prototype. [ABSTRACT FROM AUTHOR]

Power modules are the most common components to fail in power converters that are employed in mass transportation systems, thus leading to high unscheduled maintenance cost. While operating, high junction temperature swings occur that result in high thermomechanical stress within the structure of the power module, reducing the lifetime of the module. Liquid metals as a cooling medium received so far little attention in the area of power semiconductor cooling, despite being able to remove high heat fluxes. This paper shows for the first time how liquid metal is used to reduce actively the junction temperature swing. A magnetohydrodynamic (MHD) pump has been designed for this purpose allowing active control of the flow rate of the liquid metal that impinges against the baseplate of the module. The pump has been 3-D printed and is attached directly to the power module. A closed-loop temperature control system is implemented, able to estimate the insulated-gate bipolar transistor's junction temperature, and thus, controls the MHD power. This paper presents simulation and experimental results showing reductions in the temperature swing over the full load cycle with 12 °C as the highest observed reduction rate. This paper also shows detailed designs of the MHD pump and the controller hardware. [ABSTRACT FROM AUTHOR]

Dual active bridge (DAB) based converters offer the benefit of smaller volume due to high-frequency isolation and controllability of active power flow, making them attractive for various applications, such as renewable energy generation, plug-in hybrid vehicles, and distribution systems. This paper presents a novel converter topology along with a modulation strategy for a DAB-based three-phase ac to dc converter. The major benefits are single-stage conversion, no unreliable intermediate dc-link capacitor, reduced number of switches, i.e., only two active switches on the ac side, simple control scheme, open-loop unity power factor operation, bidirectional power flow, and partial soft-switching. This paper presents the analysis of all the operating modes of the converter, resulting in the analytical estimation of power transfer and rms winding current and investigation of soft-switching conditions for the power devices. Simulation and experimental results have been presented to demonstrate the advantages of the proposed technique and accuracy of the analysis.1 [ABSTRACT FROM AUTHOR]

This paper discusses dynamic behavior of a dual-active-bridge (DAB) dc–dc converter. Conventional phase-shift control methods for the DAB converter may cause dc offsets in both inductor current and transformer magnetizing current in transient states. The dc offset in the inductor current would introduce an excessive peak current through the switching devices. The dc offset in the magnetizing current may induce magnetic-flux saturation. Conventional methods simultaneously turn on and off the diagonal switches in each H-bridge converter and produce a square-wave voltage with a 50% duty ratio. In contrast, the proposed method in this paper independently controls each switch to modify the duty ratio in transient states. This paper clearly derives the requirements of each switch to eliminate the dc offsets in both currents with a settling time shorter than half the switching period. Experimental results using a 5-kW 20-kHz system verify the validity of the proposed control method, which is effective not only in a single step change, but also in a continuous change in the phase-shift reference. [ABSTRACT FROM AUTHOR]

This paper is introducing a new method of operation for a series resonant converter, with intended application in megawatt high-voltage dc wind turbines. Compared to a frequency controlled series resonant converter operated in subresonant mode, the method (entitled pulse removal technique) allows the design of the medium frequency transformer for highest switching frequency, while being operated at lower frequency without saturation. The main focus of this paper is to identify and analyze the operating modes of the converter with pulse removal technique. With the use of variable frequency and variable phase displacement in subresonant mode, the new method of operation promises transformer size reduction and facilitates soft-switching transition of the insulated gate bipolar transistors (IGBTs) and line frequency diodes on rectifier side. Four modes of operation are identified, while equations for output power, voltage, and current stress are identified. Experimental results are concluded on a 1 kW, 250 V/500 V prototype. [ABSTRACT FROM AUTHOR]

This paper proposes a hybrid electronic and magnetic structure named a variable-inverter-rectifier-transformer (VIRT) that enables a transformer with fractional and reconfigurable effective turns ratios (e.g., 12:0.5, 12:2/3, 12:1, and 12:2). This functionality is valuable in converters with wide operating voltage ranges and high step-up/down, as it offers a means to reduce the turns count and copper loss within the transformer while also facilitating voltage doubling and quadrupling. These properties are especially beneficial for miniaturizing the transformer stage in many power electronics applications, such as universal serial bus wall chargers. We introduce the principle of operation of the structure and present models for its magnetic and electrical behavior. The instance of VIRT described in this paper comprises four half-bridge switching cells distributed around a planar magnetic core and connected to two “half-turns” wound through that core. By controlling the operating modes of the half-bridge cells, we gain control over the flux paths and current paths used in the transformer, and this hybridization enables fractional and reconfigurable effective turns ratios. An experimental prototype integrates the VIRT with a stacked-bridge LLC converter to accommodate a widely varying input (120–380 \textV\text{dc}) and output (5–20 \textV\text{dc}), and VIRT is shown to be highly beneficial in keeping efficiency high over this wide output voltage range. [ABSTRACT FROM AUTHOR]

Constant on-time V^2 control for point-of-load buck converters has instability issues in the cases that the output capacitors' RC time constants are small. This paper intensively studies the proposed solution using capacitor current ramp compensation, which is a superior solution featuring fast response and universality. A frequency-domain small-signal model based on describing function method is proposed in this paper. The time-domain large-signal response to the load step change is analyzed. The analysis illustrates the unique transient response behaviors of the capacitor current ramp compensated V^2 control. The design optimization methodology based on frequency-domain and time-domain analysis is presented. The proposed model and the design guidelines are verified by the experimental results. [ABSTRACT FROM AUTHOR]

This paper presents a generalized power-decoupling control scheme using a multiport isolated bidirectional converter for a multilevel inverter, which has multiple dc links inside. In the proposed method, a single power-decoupling capacitor is needed for all the dc links in the multilevel inverter cell. First, a prototype of the power-decoupling concept of individual H-bridge cells in the multilevel inverter is proposed, using a separate power-decoupling circuit. Then, a more advanced one-step power-decoupling method is proposed. The lifetime and reliability of the multilevel inverter is improved as film capacitors replace the large capacitance electrolyte capacitors. A multi-input ports/single output voltage-fed dual half-bridge converter (MDHB) is used for the power-decoupling circuit. A steady-state analysis for the peak and root mean square of the MDHB current is carried out for the loss breakdown. The currents are functions of the switching frequency, phase shift, leakage inductance, turn ratio, and output voltage, which make the multiport transformer design complex. A design methodology is proposed, which takes into account the design of the copper and core losses as functions of the switching frequency and number of turns. Furthermore, a special winding method for the input port is illustrated to obtain identical leakage inductances for the uniform current distribution in the multiport transformer. The proposed MDHB employs a current-sensorless power-decoupling control that contributes to the spontaneous ripple rejection of all the dc links without individual link current information, as well as to the cost and size reduction. Hence, the ripple-rejection controller is independent of the control configuration of the multilevel inverter, and also available for universal applications of various inverter topologies. Since the primary-input ports of MDHB share a single magnetic core for interfacing the ripple power to the unified secondary ripple capacitor, the controller design becomes difficult in considering the dynamic interaction among the ports, along with the average-voltage control loop design. In this paper, the dynamic analysis and controller design procedure of the circuit is also presented. The power decoupling is achieved even when the ripple frequency is other than the double frequency of the inverter output, since the single-pole transfer function of the small-signal model of the MDHB allows sufficient phase margin, along with high bandwidth. The proposed power-decoupling method for the multilevel inverter is validated with the help of simulation and 1.2-kW hardware prototype experimental results. [ABSTRACT FROM AUTHOR]

Class $E^2$ DC–DC converter composed of Class $E$ power amplifier (PA) and rectifier is a promising candidate for MHz wireless power transfer. It is soft-switching based and able to achieve high efficiency at MHz frequency. However, the converter implemented through traditional static design is sensitive to the variations of operation condition. Its performance gets deteriorated when DC load and coil coupling deviate from their respective optimum values. This paper demonstrates that the degradation of system efficiency is mostly due to the mismatch of PA load, and the efficiency drop can be efficiently improved by adding an L-type impedance matching network (IMN) after PA. A fixed IMN is sufficient to maintain a high efficiency, while a tunable IMN is required to ensure stable output power when operation condition dramatically changes. Key techniques, particularly system-level optimization, are discussed in this paper that ensure high efficiency over a wide range of variation in operation condition and also with reduced capacitor/inductor tuning ranges in the IMN. The 6.78-MHz Class $E^2$ DC–DC converters with and without the fixed/tunable IMN are fabricated and measured for validation purposes. The experimental results show that both high efficiency ( $>$66%) and stable output power (around 9 W) are maintained for the tunable converter when there are variations in the DC load and coil coupling. [ABSTRACT FROM AUTHOR]

Superjunction MOSFETs in cascode configuration with low-voltage silicon MOSFETs are evaluated in this paper. The proposed structure combines the good switching performance provided by the cascode configuration with the benefits of the silicon technology such as its robustness, maturity, and low cost. This paper aims to explain and to demonstrate the reduction of switching losses of superjunction MOSFETs in cascode configuration with respect to their standalone counterparts (directly driven). A detailed simulation analysis of power loss contributions is carried out under hard-switching operation. Moreover, experimental evidence is provided using a boost converter (100–400 V) operating in continuous conduction mode for different switching frequencies (100–400 kHz) and output power levels (180–500 W). [ABSTRACT FROM AUTHOR]

In this paper, we demonstrate how latency insertion method (LIM) can be used for real-time simulation of high switching frequency power electronics systems and how this approach can be implemented for scalable Field Programmable Gate Array (FPGA) execution. We first present a summary of the LIM and how this method can be developed into a solver for high-performance FPGA execution. We then present how common power electronics topologies—buck and boost—can be modeled using the LIM approach, followed by how the LIM model of a three-phase dc/ac converter is created. Afterward, we demonstrate the accuracy of the developed FPGA solver through a set of power electronic system examples, with each example compared with near ideal results of same example provided by a traditional electromagnetic transient type solver. We complete the paper analyzing the scalability of the proposed approach on FPGA devices, both in terms of achievable time step as well as of resource usage. [ABSTRACT FROM AUTHOR]

This paper introduces a non-isolated high step-up dc–dc converter with dual coupled inductors suitable for distributed generation applications. By implementing an input parallel connection, the proposed dc–dc structure inherits shared input current with low ripple, which also requires small capacitive filter at its input. Moreover, this topology can reach high voltage gain by using dual coupled inductors in series connection at the output stage. The proposed converter uses active clamp circuits with a shared clamp capacitor for the main switches. In addition to the active clamp circuit, the leakage energy is recycled to the output by using an integrated regenerative snubber. Indeed, these circuits allow soft-switching conditions, i.e., zero voltage switching and zero current switching for active and passive switching devices, respectively. The mentioned features along with a common ground connection of the input and output make the proposed topology a proper candidate for transformer-less grid-connected photovoltaic systems. The operating performance, analysis and mathematical derivations of the proposed dc–dc converter have been demonstrated in the paper. Moreover, the main features of the proposed converter have been verified through experimental results of a 1-kW laboratory prototype. [ABSTRACT FROM PUBLISHER]

This paper proposes a new bidirectional resonant dc–dc converter suitable for wide voltage gain range applications (e.g., energy storage systems). The proposed converter overcomes the narrow voltage gain range of conventional resonant dc–dc converters, and meanwhile achieves high efficiency throughout the wide range of operation voltage. It is achieved by configuring a full-bridge mode and a half-bridge mode operation during each switching cycle. A fixed-frequency phase-shift control scheme is proposed and the normalized voltage gain can be always from 0.5 to 1, regardless of the load. The transformer root-mean-square (rms) currents in both the forward and reverse power flow directions have a small variation with respect to the voltage gain, which is beneficial to the conduction losses reduction throughout a wide voltage range. Moreover, the power devices are soft-switched for minimum switching losses. The operation principles and characteristics of the proposed converter are firstly analyzed in this paper. Then the analytical solutions for the voltage gain, soft-switching, and rms currents are derived, which facilitates the parameters design and optimization. Finally, the proposed topology and analysis are verified with experimental results obtained from a 1-kW converter prototype. [ABSTRACT FROM PUBLISHER]

The modeling and control of a buck–boost and stacked dual half-bridge (DHB) integrated bidirectional dc–dc converter have been studied in this paper. This converter features high-voltage transfer ratio, high efficiency, and the minimum number of switches. In this paper, an extended, continuous, full-order, state-space averaging modeling method is proposed. Compared with existing methods, the proposed method exhibits higher coincidence with the switching circuit simulation, in steady and especially dynamic states. Due to its high dynamic accuracy and low complexity, the proposed modeling method provides a better theoretical analysis and a fast simulation tool for transient process and control design of converters with dual-active-bridge units, especially with DHB units. By using this method, the high-frequency transformer series inductance current is directly divided into a sampled dc component and a fluctuant component. Only the sampled dc one is included into state variables, but both components are considered into state equations. Besides, this method regards the entire converter as a linear superposition of its subsections, which provides a stepwise modeling based on linearization of subsections. Moreover, a decoupled proportional-integral control method is proposed to enhance the stability and dynamic response of the converter. This control method is analyzed by the proposed models, which can be regarded as an application of the proposed modeling method. Simulation and experiments have validated both the proposed modeling and the decoupled control strategy. [ABSTRACT FROM PUBLISHER]

This paper proposes a current sensorless control strategy for the dual active bridge (DAB) converter with nonlinear disturbance observer (NDO)-based load current feedforward. The proposed method can regulate both the dc-bus voltage and the current of the DAB converter without current sensors. Several performance indexes are established for the parameter design and a detailed design method is presented in this paper. When a single-phase H-bridge inverter is connected, the double-frequency oscillation from the feedback path is suppressed by proper parameter design, while the transient response of dc-bus voltage can be further improved by the NDO-based load current feedforward with a notch filter in the feedforward path. The performance of the proposed control method and the effectiveness of the parameter design are verified in a prototype by experimental results. [ABSTRACT FROM PUBLISHER]

Voltage ripple in single-phase ac–dc converters is usually disregarded to design the dc-link voltage control system, since large dc-link electrolytic capacitors are typically employed. However, replacement of electrolytic capacitors by film capacitors has been widely considered for increasing reliability. Consequently, due to cost constraints, such replacement usually employ low capacitance and may be combined with fast dc-bus voltage controllers. This paper shows that the conventional linear time-invariant (LTI) model may not represent the real converter behavior for reduced capacitance and/or faster controllers, leading to poor system performance or even instability. In this way, for any of these cases, the linear time-periodic (LTP) model is highly encouraged for stability and transient analysis as a tool for the controller design. Experimental results confirm that stability margins are precisely obtained from the LTP model but may not from the LTI model. Finally, this paper also compares both LTI and LTP models while considering the control gain and the dc-bus capacitance size. It is graphically revealed that the phase margin of the LTI model diverges from the LTP model for low dc-bus capacitances and high control gains. [ABSTRACT FROM PUBLISHER]

This paper presents a new feed-forward strategy for suppressing low-order harmonic circulating currents in pulsewidth-modulated (PWM) based modular multilevel converters (MMCs). The approach is based on the new average model approach established in this paper, which identifies cross-coupling interactions between the system-level and submodule elements using decomposed dependent sources. As well as improving the damping of the system, the major advantage of this approach is that it maintains the natural DC bus balance property of a PWM modulated MMC by considering the upper and lower arms together (unlike existing feed-forward schemes which treat each MMC arm independently). Moreover, unlike existing direct control resonant strategies, which require careful gain tuning and are highly dependent on the ac system frequency, the proposed approach achieves wideband circulating current ripple suppression without requiring knowledge of the circulating current harmonic frequencies and needs only a simple proportional–integral (PI) controller to regulate the circulating current dc component for power balance. This makes it particularly suitable for use in multifrequency or variable-frequency ac systems. Extensive simulation and matching experimental results, including steady-state and transient responses compared against existing circulating current suppression approaches, validate the effectiveness and benefits of this new feed-forward compensation technique. [ABSTRACT FROM PUBLISHER]

The subject of this paper falls under the development of power electronics for more electric aircraft systems. The study concerns the design of a converter whose function is to generate a 300-V dc bus from a standard 28-V dc avionic network. Various systems, such as motor drives, need to be connected to the 28-V dc network. Their design could be simplified significantly, and standardized, by introducing this intermediate 28–300-V stage. The step-up converter in the proposed configuration is integrated as a part of the system. The power specification is 10 kW, which leads to very high-current values on the 28-V side. The choice of the converter topology, therefore, needs to match this central constraint. The proposed converter uses six boost cells, associated to constitute a series–parallel architecture. This arrangement leads to significantly more optimal sizing for high step-up ratios than conventional boost-cell configurations. Cell interconnection is implemented by means of a monolithic InterCell transformer to reduce the weight of the magnetic part. This paper describes the topology, design, and construction of the lab prototype, as well as experimental results obtained during testing. [ABSTRACT FROM PUBLISHER]

This paper presents a hybrid seven-level converter based on T-type converter and H-bridge cascaded suitable for low-voltage and high-power-density applications. The operation principles and conduction paths are analyzed comprehensively. Voltage balance control of the floating capacitors is the key point of this paper. Mathematical expressions of capacitor voltage balance conditions are deduced based on sinusoidal pulse width modulation (SPWM). The results show that floating capacitor voltages are only balanced when the modulation index is below 0.82 under SPWM. In order to enlarge the modulation index ensuring the capacitor voltage balance, space vector modulation (SVM) is also applied to regulate floating capacitor voltages taking advantage of redundant switching vectors. Meanwhile, in SVM, there are no additional control requirements for the capacitor voltage. Taken both SPWM and SVM into consideration, the limit to the range of operation for this seven-level converter is presented, which is a function of the modulation index and the power factor. The merit of dc voltage utilization improvement in this topology is also analyzed based on simulation results. Simulations and experimental results under different modulation index and RL load are presented to verify the modulation strategies illustrated in this paper. [ABSTRACT FROM PUBLISHER]

The unified knowledge on power converter design and manufacturing technology establishes a powerful tool, where the cost and topology realization can be analyzed simultaneously. This paper collects the design practice and cost estimation of various components in a power electronics converter and unites that to a choice of the assembling and manufacturing processes and resulting cost of the complete converter. The outcome of this work specifies the power converter at predefined power level and cooling condition and demonstrates the cost drivers of the complete unit depending on production volumes. As a case study, the cost of an inverter for a full electric or hybrid vehicle application is estimated and the results are compared with figures available in the literature, yielding the conclusion that the validity of such figures is highly dependent on production volumes and power levels. The essence of this paper is a set of general, reliable, and fast design models and production charts, in accordance with realistic cost estimates for the sake of system optimization and development of cost effective electric drives from small series to large volumes. [ABSTRACT FROM AUTHOR]

High-frequency current harmonics injected into the point of common coupling, mainly at the switching frequency and its multiples introduced by the modulation of grid-connected converters, should be limited to comply with grid codes. This requirement can be satisfied by using trap filters with LC-traps tuned at the switching frequency and its multiples in replacement of conventional L filters. However, all existing trap filters are subject to certain problems, e.g., sensitivity to grid impedance variation and decreased high-frequency roll-off rate. In view of this, this paper presents a trap-LCL filter with its parallel resonant LC-trap located on the converter side, named as LT-C-L filter. The modeling and analysis presented in this paper show that the LT-C-L filter can be the most promising trap filter due to its advantages such as high roll-off rate, robustness against parametric variations of grid impedance and passive damper, satisfactory harmonic attenuation at the switching frequency, reduction of converter current total-harmonic-distortion, and flexible design of filter components through magnetic integration. A single-phase ac/dc grid-connected converter prototype has been built and tested in the laboratory, and experimental results are presented to verify the superiority of the proposed filter. [ABSTRACT FROM AUTHOR]

An extended-duty-ratio (EDR) boost converter is studied extensively in this paper for high voltage gain applications with a wide input (and/or output) voltage range. The EDR is a unique combination of an interleaved, multiphase boost converter and switched capacitor configuration that achieves high voltage gain with significantly lower switch voltage stress and switching losses compared to conventional high-gain solutions. Most of the switches in the multiphase EDR experience only a fixed fraction of the output voltage ($1/M, 2/M$ , etc., where $M$ is the number of phases). Through extensive analysis over a wide operating range, it is shown here that the EDR boost converter has inherent current sharing among the phases only in a limited range of duty ratio— $(M-1)/M \leq D \leq 1$. As the duty ratio reduces beyond this range as required in wide input voltage applications, inherent current sharing property is lost. In this paper, techniques to ensure current sharing under all operating zones without requiring current sensors are presented. Instead of having equal duty ratio for each phase, it is adjusted for each phase according to the operating region of the converter. Extensive analysis is presented to derive the required duty ratio changes for the different phases. The proposed concept is validated with experimental results from a 250 W, 3-phase EDR boost, and GaN-based hardware prototype. [ABSTRACT FROM AUTHOR]

This paper proposes a very simple analog control for quasi-square-wave zero voltage switching (QSW-ZVS) and triangular current mode bidirectional converters. The proposed circuit controls the inductance current, thanks to the use of a variable-width hysteretic current mode control. The upper and lower bounds of the hysteretic band are clamped to ensure QSW-ZVS operation with a single current command and independently from power flow direction. This enables the control to achieve a seamless transition between source and sink modes. The advantages and disadvantages of the proposed analog control are analyzed and two different power converters are built to demonstrate the validity of this solution: a 50 W, 48 to 24 V bidirectional buck converter and a 100 W, 24 to 48 V bidirectional boost converter. [ABSTRACT FROM AUTHOR]

The power efficiency and weight of present point-of-load (POL) dc–dc converters for drone applications are often compromised because they suffer from large switching losses at continuous conduction mode for heavy loads and excessive hardware overheads at discontinuous conduction mode for light loads. This paper presents a boundary conduction mode (BCM) control scheme for POL converters embodying a single operation mode. This is achieved by means of a hysteresis voltage controller to turn on/off the output power stage when necessary. The proposed BCM control scheme achieves high power efficiency (≥91.2%) over a wide load range (5 mA–1 A) by means of fully soft switching. Specifically, a hysteretic current controller is proposed to realize ZCS, and an adaptive dead time controller is proposed to realize ZVS. Further, the proposed BCM control scheme requires a small output inductor (0.82 μH) by means of designing the customizable peak inductor current. To verify the proposed BCM control scheme, we realize a BCM-based POL converter that features an input voltage range of 5–16 V, output voltage range of 2.5–8 V, switching frequency of 1.5 MHz, peak power efficiency of 96.8%, and ≤35 mV output voltage undershoot/overshoot for 1-A load step. When being benchmarked against state-of-the-art counterparts, the proposed design features the lowest voltage undershoot/overshoot, the highest switching frequency, ∼5.7× smaller inductor, and ∼11% higher power efficiency at light loads. [ABSTRACT FROM AUTHOR]

An isolated bidirectional dc–dc converter, which combines parallel-connected two-level converters (TLCs) on the medium-voltage side and a modular multilevel converter (MMC) on the high-voltage side, namely a TLC-MMC converter, is a promising candidate for the interconnection of medium-voltage direct current (MVDC) and HVdc grids. Different from typical phase-shift controlled isolated bidirectional dc–dc converters, transformer currents of a TLC-MMC converter are regulated by the MMC in a closed-loop manner in order to achieve extremely low switching losses and low total device rating of power-semiconductor devices in TLCs. This paper addresses the dedicated operation technique and the voltage-balancing control of the TLC-MMC converter. The MMC in the TLC-MMC converter operates with six-step phase voltages and sinusoidal phase currents. Such an operation makes the MMC present remarkable differences to ac–dc applications. The direct-modulation technique, which is the most-used technique performed to MMCs in line-frequency ac–dc power conversion, has been concluded not applicable to the MMC in a TLC-MMC converter due to the significant sixth-order oscillation resulted in the dc-link voltage. Thus, the indirect-modulation technique is employed, and consequently a closed-loop voltage-balancing control is mandatory for the MMC. Possible measures for voltage balancing have been explored, and effective voltage-balancing control with a simplified implementation is proposed. Validity and effectiveness of the proposed control strategy have been verified by both simulations and experiment using a downscale prototype. [ABSTRACT FROM AUTHOR]

In this paper, a multisource switched capacitor based boost multilevel inverter is proposed. The proposed topology features less number of components, high gain, self-charging capability of capacitors, reduced size of filter components. The modes of operation of the proposed converter and design guidelines of converter components are discussed. A comprehensive comparative study of the proposed converter topology with the topologies in the literature is given. Analytical expression for capacitor energy utilization (CEU) factor for the proposed topology is derived and the feasibility of the proposed converter with respect to CEU for the designed power rating is verified. The analytical performance of the proposed converter topology is verified through simulation studies. The common mode voltage and leakage current in the proposed topology are analyzed. Experimental prototype of the proposed converter topology with two sources and two capacitors for power rating of 500 W is developed and tested with resistive, inductive, and nonlinear loads. The experimental and simulated results are in close agreement with the analytical steady-state performance of the proposed converter. [ABSTRACT FROM AUTHOR]

In this paper, a novel topology of modular dc–dc converter has been proposed for medium voltage dc (MVdc) integration of high-penetration distributed PV. The proposed topology is featured with input-independent and output-series connected configuration and intermodule power balancing units (PBUs). A high voltage gain could be achieved with series-connected submodules (SMs), while each SM's input port is connected with PV array to realize the independent maximum power point tracking (MPPT) control function. PBUs with bidirectional power conversion ability are installed between adjacent SMs for the elimination of intermodule power mismatch. The operation principles of the proposed converter have been explained in detail along with the corresponding control strategies. The design principles of major passive components have been investigated on the basis of boundary operation conditions, while a quantitative analysis of steady-state power losses has been performed. Moreover, a comparative study is conducted from the aspects of operation range, topology complexity, component stress, and power efficiency. The theoretical results have been validated by both simulations and down-scaled experiments. [ABSTRACT FROM AUTHOR]

This paper proposes the design of gray wolf optimizer (GWO) algorithm-based fractional order proportional integral (FOPI) controller for power factor correction (PFC) using interleaved dc–dc single ended primary inductance converter converter with improved performance characteristics such as speed, accuracy, and stability. The detailed analysis and modeling of the proposed converter are presented. The optimal parameters of FOPI controller are obtained using GWO algorithm to improve the speed of response of the system. FOPI controller provides better performance in terms of robustness and stability since it has one more adjustable parameter than the conventional proportional integral (PI) controller. The cascade control strategy is implemented for the proposed converter with GWO-based FOPI controller as inner current and outer voltage controllers for PFC and load voltage regulation. The performance characteristics of the proposed system are analyzed and compared with conventional and other optimization techniques using MATLAB/Simulink software. A prototype of the proposed converter controlled by TMS320C2000 microcontroller for an output power of 200 W is tested and validated with the simulation results. The proposed system is used for powering devices like robots in critical applications such as military, space craft, etc., where stability, speed, and accuracy are major concerns. [ABSTRACT FROM AUTHOR]

A fast output voltage equalization control strategy applied to 10-kV/100-kW high power density photovoltaic dc–dc converter system is proposed in this paper. The converter modules in the system have two dynamic priority factor loops for fast response with an inconsistent voltage between modules and a soft start-up circuit to precharge output capacitance for solving inrush current problem in boost circuit. The proposed strategy can realize fast voltage equalization control under inconsistent leakage inductance and parasitic resistance parameters condition between modules compared to the traditional unified duty cycle control strategy. The fast equalization performance is verified by 10-kV/100-kW photovoltaic dc–dc converter system. The converter system adopts an isolated boost full-bridge topology and input parallel output series structure, which meets high conversion ratio and high-power density requirements. [ABSTRACT FROM AUTHOR]

This paper proposes an improved LLC resonant converter with reconfigurable hybrid voltage multiplier for wide output voltage range applications. By adopting three legs and two active switches, the rectifier can be reconfigured to three configurations, i.e., full-bridge rectifier, hybrid voltage-multiplier rectifier and voltage-multiplier rectifier, covering the range of more than three times of the minimum output voltage. Compared with conventional LLC converter, the operating range of each configuration is narrowed so that the magnetizing inductance is optimized and switching frequency range is narrowed to achieve higher efficiency. Pulsewidth plus pulse-frequency modulation strategy is employed to achieve smooth transition between these operation modes. Zero-voltage switching of all power mosfets and zero-current switching of all secondary-side diodes are achieved as well. Detailed operational principles, characteristics, design consideration, and control stagey of the proposed converter are analyzed. A 3.3 kW 150–450 V output prototype is built and tested to verify the effectiveness and advantages of the proposed converter. [ABSTRACT FROM AUTHOR]

In the no-load condition, LLC converter usually fails to regulate its output voltage although it operates at a high switching frequency. Till now, it is hard to obtain the exact relationship between design parameters and the maximum switching frequency for no-load regulation capability. In this paper, a specific criterion for no-load regulation of LLC converter is provided, without using active components or other modulation schemes. By analyzing the macroscopic switching period and microscopic switching transition in the no-load condition, it is shown that not only the peaking resonant current during the switching transition, but also the resonant tank design affect the no-load regulation of the LLC converter, which affects the no-load regulation capability. Furthermore, the relationship among design parameters is analyzed and the design guideline is also provided to achieve no-load regulation at the specified maximum switching frequency. To verify the effectiveness of the proposed design, 400 V input and 50 V/200 W output prototype is built and tested. [ABSTRACT FROM AUTHOR]

A systematic method for developing ultra-wide output voltage range power supply based on modular switched-converter principle is proposed in this paper. The basic symmetric switched-converter (SSC) module is composed of two dc–dc modules, two diodes, and one active switch. Multi-stage SSC modules are generated by symmetric cascaded connection method. By controlling the active switches in multi-stage SSC modules, the connections of all the dc–dc modules’ output ports can be changed flexibly among series, parallel, and partial–parallel–partial-series connections. Then segmented regulation can be realized and system output voltage range can be widely extended. Meanwhile, the voltage range of each dc–dc module can be narrowed and the voltage/current stress can be reduced to simplify the design, increase device utilization ratio, and improve overall efficiency. A full-bridge isolated buck–boost converter with a semiactive rectifier, which features soft-switching and wide voltage adjustment range, is adopted as the dc–dc module to realize the proposed system. Input current sharing control strategy is adopted to ensure proper power balancing in all possible operating modes. The stability of the proposed system is also explored. Simulation and experimental results are provided to verify the effectiveness and advantages of the proposed system configuration, the switched-converter principle, and the control strategies. [ABSTRACT FROM AUTHOR]

Photovoltaic (PV) systems having rechargeable batteries are prone to be complex and costly because multiple converters are necessary to individually regulate a load, PV panel, and battery. This paper proposes novel nonisolated multiport converters (MPCs) integrating a bidirectional pulsewidth modulation (PWM) converter and phase-shift-switched capacitor converter (PS-SCC) for standalone PV systems. A PWM converter and PS-SCC are integrated by reducing the total switch count, realizing the simplified system and circuit. In the proposed MPCs, two control freedoms of duty cycle and phase shift angle are manipulated to individually regulate the load, PV panel, and/or battery. The detailed operation analysis was performed to mathematically derive gain characteristics and zero voltage switching operation boundaries. For the battery discharging mode, in which the PV panel is not available and the MPC behaves as a single-input–single-output converter with two control freedoms available, the optimized control scheme achieving the lowest rms current is also proposed to maximize power conversion efficiencies. Various kinds of experimental verification tests using a 200-W prototype were performed to verify the theoretical analysis and to demonstrate the performance of the proposed MPC. [ABSTRACT FROM AUTHOR]

An isolated bidirectional dc-dc converter, which combines multiple two-level converters (TLCs) in parallel on the medium-voltage side and a modular multilevel converter (MMC) on the high-voltage side, namely the TLC-MMC converter, is a promising candidate for the interconnection of MVdc and HVdc grids. In utility applications, the availability of power converters is of great importance, which makes the fault-tolerant operation (FTO) capability a required feature. In this paper, an FTO scheme of the TLC-MMC converter in case of a TLC failure is addressed. The FTO capability is enabled by employing only mechanical disconnectors. The faulty TLC can be bypassed and isolated for maintenance, and the TLC-MMC converter can continuously operate with a reduced power capacity. A dedicated mode-transition strategy is developed, whereby the TLC-MMC converter can transit to the fault-tolerant mode seamlessly without resulting in overvoltage or overcurrent despite the involvement of low-speed mechanical disconnectors. Thus, the proposed approach can effectively enhance the availability of the TLC-MMC converter. The validity of the proposed approach is verified by both simulation and experimental test with a down-scale prototype. [ABSTRACT FROM AUTHOR]