Search

Position sensorless control of interior permanent magnet synchronous motors (IPMSMs) is of great importance for the sake of the cost reduction and robustness improvement. An improved position sensorless method based on adjustable high-frequency (HF) square-wave voltage injection has been proposed for the IPMSM drive under zero- and low-speed regions. The general detection method of position from positive- and negative-sequence HF current response has been developed by the simple algebraic operations of data at some adjacent sampling instants. In addition, the proposed method not only can retain the advantage of the removal of low-pass filters in current feedback but also can increase the voltage margin of inverter with adjustable frequency setting of HF signal compared with existing square-wave voltage injection methods. Comprehensive experimental results have been given to verify the proposed theoretical analysis. [ABSTRACT FROM AUTHOR]

In this article, a minimum-copper-loss fault-tolerant control scheme is proposed for open-phase fault and open-switch fault of dual three-phase permanent magnet synchronous motor (DT-PMSM) drives. Both the winding configurations of isolated neutral points and connected neutral points are studied in this article. In conventional minimum-copper-loss fault-tolerant control schemes, the constraints of sinusoidal phase currents result in insufficient copper-loss reduction. Different from them, the current references with the theoretically lowest copper losses are first derived and applied for different fault cases of DT-PMSM drives without using any unnecessary constraints in the proposed fault-tolerant control scheme. Thus, all phase currents in the proposed minimum-copper-loss fault-tolerant control scheme are optimized to be nonsinusoidal waveforms. Besides, the copper losses are further reduced by fully utilizing the remaining healthy switch in the faulty inverter leg for the open-switch fault of DT-PMSM drives with the proposed scheme. It has been theoretically and experimentally proved that the proposed fault-tolerant control scheme can reduce copper losses than all existing fault-tolerant schemes for both open-phase fault and open-switch fault in typical two-level voltage-source-inverter-fed DT-PMSM drives. [ABSTRACT FROM AUTHOR]

A feedback linearization based direct torque control (FL-DTC) scheme is designed for interior permanent magnet synchronous motors drives. Several main aspects related to FL are studied thoroughly. A proper choice of two new state variables (the torque and the squared amplitude of stator flux) yields the exact input–output linearization decoupling of the closed-loop system. The FL-DTC frame is obtained after finding a feasible diffeomorphism. For the partially linearized subsystem, i.e., the independent torque and flux loops, two FL-DTC-based controller design solutions are provided. The control problem of internal dynamics is converted to an absolute tracking problem of an equivalent Lur'e system. [ABSTRACT FROM AUTHOR]

In this paper, diagnosis and tolerant control schemes have been studied for common electrical faults in T-type three-level inverter fed dual-three phase permanent magnet synchronous motor (PMSM) drives for safety-critical applications. Based on vector space decomposition and double three-phase space vector modulation, diagnostic and tolerant control methods have been developed comprehensively for open-phase faults, open-switch faults, and short-switch faults in T-type three-level inverter fed dual-three-phase PMSM drives, in such way that misdiagnosis of different faults sharing similar faulty features can be avoided. In particular, a two-step diagnostic scheme is proposed in order to simplify the diagnostic process. The first step is to identify the faulty phase and fault category by analyzing current trajectories on harmonic subspace, and the second step is to determine the specific fault type in a small fault-searching area obtained from the first step. In the aspect of fault-tolerant control, a novel current compensation method is proposed for open-phase fault without changing the machine model, space vector diagram, and control framework. Open-switch faults and short-switch faults are tolerated by making full use of the remaining vectors after faults. The validity of the proposed fault diagnosis and tolerance schemes has been verified by experiments. [ABSTRACT FROM AUTHOR]

This paper proposes a novel nonlinear optimization-based sensorless control scheme for surface-mounted permanent magnet synchronous motors (SPMSM) over wide speed range operations. Two algebraic constraints derived from the voltage equations and the flux equations of the SPMSM system are fundamental to the establishment of the proposed scheme. The position estimation algorithm generates the rotor position estimate via the stator flux estimates obtained by minimizing an equality constrained scalar function. Specifically, the flux information is extracted both from the voltage-based flux model and the current-based flux model, which contributes to its robustness against the inherent weakness of the pure integrator to dc offsets. Meanwhile, a nonlinear observer, based on the standard gradient search, is constructed for speed estimation. The proposed method is unique because the position estimation and the speed estimation are achieved independently; thus, the complexity associated with the speed dependence in position estimation is eliminated. Further, it is simple to implement. The feasibility and effectiveness of the proposed position algorithm and the speed observer have been verified by experiments under different operating conditions. [ABSTRACT FROM AUTHOR]

This paper studies and proposes the vector space decomposition-based direct torque control (DTC) scheme for the T-type neutral-point-clamping (T-NPC) three-level inverters-fed double-stator-winding permanent magnet synchronous machine (PMSM) drive, which provides an effective solution for high-power high-reliability applications. The key is to propose a simple but effective space vector modulation (SVM) for DTC of T-NPC double-stator-winding drives-based two-step voltage vector synthesis, in such a way that good dynamic response and harmonic performance are obtained. The closed-loop controllers on harmonic subspace are incorporated to suppress the possible harmonics induced from back electromotive force and unbalanced parameters in phase windings of electrical machine. Furthermore, a hybrid current control is proposed for fault-tolerant operation of the T-NPC double-stator-winding PMSM drives under one-phase open-circuit conditions. In the hybrid current controller, the healthy winding still uses the SVM-DTC control while the faulty winding uses the closed-loop current controller to track the optimized current references. Both simulation and experimental results are presented to verify the performance of the proposed switching strategies and control schemes. [ABSTRACT FROM AUTHOR]

In this paper, three control schemes with variable switching frequencies are proposed and analyzed for the paralleled voltage source inverters (VSIs) fed permanent magnet synchronous motor (PMSM) drive. The proposed schemes could be applied in the low-speed operation region of high-power drive system, where the frequency modulation index is high. First, the field-oriented control (FOC) with phase-shifted chaotic space vector modulation (SVM) under synchronous frame and the FOC with phase-shifted chaotic sinusoidal pulse width modulation under stationary frame is proposed for the paralleled VSIs fed PMSM drive. The proposed phase-shifted chaotic PWM schemes not only eliminate specific switching harmonics completely but also suppress all remaining switching harmonic peaks in the spectrum. The avoidance of inherent circulating current is also considered in designing these two schemes. Second, the direct torque control (DTC) for the paralleled VSIs fed PMSM drive is proposed with circulating current suppression. Besides inheriting the advantages of DTC, the output currents of paralleled VSIs are kept balanced. The working principles of these three methods are presented in detail. Experimental results on a laboratory prototype are given to verify the validity of the three proposed control schemes for the paralleled VSIs fed PMSM with variable switching frequencies. [ABSTRACT FROM PUBLISHER]

In this article, a fault diagnosis method is proposed to detect current sensor faults for the studied primary permanent-magnet linear motor (PPMLM) traction system, in which only two current sensors are required, and the gain fault and zero-offset fault can be distinguished. In this proposed fault diagnosis method, synchronous currents are estimated by the PPMLM model. By comparing the estimated and measured synchronous currents, estimation errors are calculated, and ac components can be extracted by corresponding filters. In the synchronous frame, the zero-offset fault and the gain fault can be detected by the single-frequency and double-frequency components, respectively. Furthermore, the fault phase also can be located. Compared with conventional fault diagnosis methods, the proposed one can distinguish gain fault and zero-offset fault but only two current sensors are required. Simulation and experimental results verify the effectiveness of the proposed fault diagnosis method. [ABSTRACT FROM AUTHOR]

In this article, a dual-vector located model predictive control (DL-MPC) method based on a single dc-link current sensor is proposed for the permanent-magnet linear motor drive system. In DL-MPC, the phase currents are reconstructed by sampled dc-link current and selected active voltage vector (VV). Meanwhile, the sunk number of phase current is defined to evaluate the accuracy of current reconstruction. The first-optimal and second-optimal VVs are determined by dual-vector location. The second-optimal VV is selected for the voltage source inverter when the sunk number exceeds the threshold. Compared with traditional MPC schemes, DL-MPC has smaller current tracking error and better dynamic performance. Meanwhile, DL-MPC has more accurate current reconstruction and lower computation burden than that of the traditional MPC. The effectiveness of DL-MPC is verified by both theoretical analysis and experimental results. [ABSTRACT FROM AUTHOR]

This letter proposes a fast current control scheme for ac drives by minimizing the latency from current sampling to the updation of a pulsewidth-modulation (PWM) command. By reconstructing the architecture of a linear controller, the minimal necessary steps to obtain the output voltage are deduced as the primary calculation, and the other computation work of the current loop is done in the postcalculation after updating the PWM command. With the proposed method, the computational delay is reduced with negligible loss in the available modulation index, and a higher stability margin or system bandwidth is realized. Also, the developed controller structure exhibits inherited antiwindup characteristics. The technique has been validated by experimental investigations on a permanent magnet synchronous motor. [ABSTRACT FROM AUTHOR]

Because both magnets and windings can be mounted in the mover, the primary permanent-magnet linear motor (PPMLM) has a low-cost advantage for subway applications. In this paper, a novel direct thrust force control (DTFC) with single dc-link current sensor is proposed for PPMLM traction system in subway applications. The first phase current is directly measured by the dc-link current sensor. The second phase current is sensed with a limited delay, which is strictly limited by the limited measurement delay principle. The third phase current is calculated based on the condition that the summation of the three phase currents is zero. During the current reconstruction, no motor parameters are required. Because PPMLM may sink in the same phase for a long time and affect the current reconstruction accuracy, the single optimal target is proposed to re-select the original voltage vector. Compared with the conventional DTFC scheme, the proposed one has nearly the same performances; especially, the maximum speed and response time remain nearly unchanged. The effectiveness of the proposed DTFC scheme is verified by experimental results. [ABSTRACT FROM AUTHOR]

Because both magnets and windings can be mounted in the mover, the primary permanent-magnet linear motor (PPMLM) has a low-cost advantage for subway applications. In this paper, a fault-tolerant control (FTC) with single phase current sensor is proposed for PPMLM traction system in subway applications. In the proposed FTC, d- and q-axis currents are estimated from the reference synchronous currents and the surviving measured phase current. The estimation is robust since no machine parameters are required. In steady-state operation, the estimated current errors are half the actual ones. As a result, the current response is slowed but the current command can be achieved. However, the achievement of control target depends on the current tracking accuracy, which is enhanced by the voltage decoupler. Compared with existed FTC schemes, the proposed one is robust and has better transient-state performances. The effectiveness of the proposed FTC is verified by theoretical analysis and experimental results. [ABSTRACT FROM AUTHOR]