Search

This paper presents an optimization framework for sequential reconfiguration using an assortment of switching devices and repair process in distribution system restoration. Compared to existing studies, this paper considers types, capabilities and operational limits of different switching devices, making it applicable in practice. We develop a novel multi-phase method to find the optimal sequential operation of various switching devices and repair faulted areas. We consider circuit breakers, reclosers, sectionalizers, load breaker switches, and fuses. The switching operation problem is decomposed into two mixed-integer linear programming (MILP) subproblems. The first subproblem determines the optimal network topology and estimates the number of steps to reach that topology, while the second subproblem generates a sequence of switching operations to coordinate the switches. For repairing the faults, we design an MILP model that dispatches repair crews to clear faults and replace melted fuses. After clearing a fault, we update the topology of the network by generating a new sequence of switching operations, and the process continues until all faults are cleared. To improve the computational efficiency, a network reduction algorithm is developed to group line sections, such that only switchable sections are present in the reduced network. The proposed method is validated on the IEEE 123-bus and 8500-bus systems. [ABSTRACT FROM AUTHOR]

This paper focuses on the issue of network connectedness (NC) in security-constrained optimal transmission switching problems, which is complicated by branch contingencies and corrective line switching. Two criteria are firstly proposed with the principle of preserving NC as much as possible within reasonable limits. By extending the electrical flow based NC constraints, a proposition is derived to associate different cases of NC with the optimum of a linear program, yielding the mathematical formulation of the NC criteria. By Karush-Kuhn-Tucker conditions, this formulation is further transformed into a tractable version which can be incorporated with existing SCOTS models without affecting the applicability of original solution approaches. Finally, case studies on various networks and SCOTS models demonstrate the efficacy of the proposed approach. [ABSTRACT FROM AUTHOR]

This paper proposes a novel data driven framework for detecting topology transitions in a distribution network. The framework analyzes data from phasor measurement units (PMUs) and relies on the fact that changes in network topology results in changes in the structure and admittance of the network. Using voltage and current phasors recorded by PMUs, the proposed method approximates network parameters using an ensemble-based deep learning model and thus, it does not require any knowledge of network parameters and load models. Using the prediction error of the proposed model, a connectivity matrix which shows the status of switches is constructed. In contrast to other methods, this proposed framework does not require a library of voltage and current transients associated with possible network transitions. It can also detect simultaneous switching actions and is robust to noise and load variations. The model yields a lower error detection rate, and its performance is validated using a modified version of the IEEE 33 bus network and a real feeder located in Queensland, Australia, under full and partial observability conditions. The proposed model has also been compared with another data driven method in terms of inference time and error detection rates. [ABSTRACT FROM AUTHOR]

This paper introduces a network topology identification (TI) method based on deep neural networks (DNNs) for online applications. The proposed TI DNN utilizes the set of measurements used for state estimation to predict the actual network topology and offers low computational times along with high accuracy under a wide variety of testing scenarios. The training process of the TI DNN is duly discussed, and several deep learning heuristics that may be useful for similar implementations are provided. Simulations on the IEEE 14-bus and IEEE 39-bus test systems are reported to demonstrate the effectiveness and the small computational cost of the proposed methodology. [ABSTRACT FROM AUTHOR]

Line-switching operations introduce several concerns to microgrid operators since they trigger reliability and power quality issues in addition to increasing the wear and tear cost of switching devices. This paper proposes a novel methodology for achieving seamless line-switching in low-inertia islanded microgrids. The proposed methodology aims at mitigating the detrimental line-switching impacts by minimizing the power flow in the switched lines at the moments of executing the switching operations. The minimization of the power flow is realized by optimizing the droop control parameters of the DGs during the transition from one network topology to another. Besides, during executing a series of line-switching operations, the sequence of switching is also optimized to minimize the total switched power. While optimizing the line-switching execution sequence, the transitional droops are optimized for each line-switching operation within that sequence. A dynamic mixed-integer nonlinear programming problem is formulated to find both the optimized dynamic transitional droops and line-switching sequence simultaneously. Simulation results demonstrate the effectiveness of the proposed seamless line-switching methodology where the switched power can be reduced by more than 80% for a single line-switching operation and 54% considering a series of four switch exchanges in addition to achieving several instances of zero-current switching. As a result, a significant decrease in the peak of voltage transients has been recorded for some cases. [ABSTRACT FROM AUTHOR]