Search

At high cutting speeds, the internal microstructure of the difficult-to-machine material Inconel 718 will change. Alterations in the internal microstructure lead to macroscopic deformations, which in turn result in the formation of adiabatic shear bands. In order to better study the formation of adiabatic shear bands during cutting Inconel 718, cutting experiments, SHPB experiments, and finite element simulations were carried out. The stored energy model for adiabatic shear bands was developed by combining the overall dislocation density and the variation of the stress field in this paper. Based on the strain gradient theory, the subroutine was compiled for secondary development to achieve multi-scale finite element simulation that can visualize the stored energy. The experiment and simulation results were combined to derive the change in stress, temperature, and overall dislocation density and to analyze the adiabatic shear bands storage energy based on the change. The analytical results are also combined with dynamic recrystallization and periodic fracture theories to characterize the formation mechanism of adiabatic shear bands. It was found that the overall dislocation density, stress, and adiabatic shear bands storage energy follow the same trend, while the temperature and shear zone storage energy follow opposite trends. [ABSTRACT FROM AUTHOR]

Electrochemical micromachining (EMM) has become a popular technology for fabricating microscale structures. To obtain higher machining localization and minor stray corrosion, a new hybrid EMM process combining air assistance and ultrasonic assistance was introduced in this paper. Simulations and experimental investigations were conducted to study the influencing mechanism and the influencing characteristics of the assisting process energies. In the multi-physics model, a reactant transport model is included, and the direct coupling between the assisting processes and the electrochemical process is achieved. Results indicate that, when the two assisting processes are applied separately, the assisting effect tend to act on the entire workpiece surface, either promotes the overall dissolution or inhibits it, usually leading to unsatisfactory results; by combining the two assisting processes, synergistic effect occurs: dissolution in the central area is promoted by the ultrasonic assistance, while stray corrosion in the margin area is hindered by the air assistance. Thus, microstructures with enhanced aspect ratio and reduced stray corrosion can be fabricated. The results also show that the surrounding airflow can produce an electrical insulating effect on both the workpiece and the cathode. When the air pressure is low, an additional concentrating effect on the electric field can be observed; however, a high air pressure leads to a greatly hindered dissolution. When the applied amplitude is appropriate, ultrasonic assistance promotes the electrochemical dissolution through disturbance effect and cavitation phenomena. But if the amplitude is too large, massive cavitation bubbles will inhibit the dissolution greatly. [ABSTRACT FROM AUTHOR]

Micro-structure on metal surface can be created with high precision and good surface quality by ultrasonic-assisted electrochemical micromachining (USEMM). One of the prevalent material removal mechanisms in ultrasonic machining (UM) is cavitation erosion. However, the mechanism of material erosion is not clear and worth investigating. This study of the mechanical and chemical effects of the ultrasonic vibration on the 6061 aluminum alloy is targeted to reveal the material processing mechanism in USEMM. Based on the built model, the velocity of micro-jet produced near the workpiece surface by ultrasonic cavitation reaches up to 350 m/s when bubble collapses computed by software MATLAB. The impact of micro-jet produces plastic micro-pits on the metal surface and the convex peak around the edge of the pits, which is verified in ABAQUS software. The metallographic microscope and curves of the electrochemical polarization behavior results indicate a significant grain refinement and a marked increase of anodic dissolution current, as well as a weaker resistance than the original workpiece in NaNO3 electrolyte during UM. The current-time curve during machining demonstrates the passive layer forms on the metal surface and then breaks down at the time of less than 0.0066s in USEMM. Micrographs of scanning electron microscope (SEM) of the machined surface in different stages show that many uniform and flat pits are formed in USEMM, compared with the local uneven pits in EMM. [ABSTRACT FROM AUTHOR]

Microdimples as a typical surface texture has been widely used for improving the properties in tribology and heat transfer fields. Ultrasonically assisted electrochemical micromachining (USEMM) is a popular method for generating microdimples as it can reduce the overcutting and enhance electrolyte renewal to improve the machining localization and promote the material removal. However, the fundamental understanding of the process and particularly the relationship between the machining performance and gap pressure is limited. In this paper, radial ultrasonicrolling electrochemical micromachining (RUREMM) is employed to generate microdimples on SS304 surface. Effects of gap pressure on the material removal rate, machining accuracy, and roughness are studied and discussed in detail. Results show that RUREMM can fabricate the microdimples and the existing ultrasonic vibration in the inter-electrode gap is more effective to enhance the machining performance. By using the selected parameters in RUREMM, the current density during machining has a 6.6% increase in RUREMM than in EMM. Moreover, the width of the microdimple is decreased by 14.6%, the depth of the microdimple is increased by 19.2%, the cross-sectional area of the machined dimple is expanded by 31.2%, the roughness of the bottom is decreased 23.9% and also, better surface quality for the side wall could be obtained. [ABSTRACT FROM AUTHOR]