Search

Abstract: The ground-coupled heat pump (GCHP) systems have been identified as one of the best sustainable energy technologies for space heating and cooling in buildings. While the foundation piles of buildings are used to partly take the place of boreholes in the ground heat exchanger (GHE) in recent years, the classical approaches of the line heat source model and the “hollow” cylindrical heat source model for the borehole GHEs fail for thermal analysis and design of the pile GHEs. Evolved from the classical models, a new “solid” cylindrical source model is presented in this paper to consider both the radial dimension and the heat capacity of the borehole or pile. Expressions of the analytical solution are derived for 1-D and 2-D new models by means of the Green’s function method. Results obtained from the new 1-D model are compared with the classical line source and “hollow” cylindrical source models of the borehole GHE, and also validated by a numerical solution of the same model. While the 1-D and 2-D solid cylindrical source models can provide adequate tools for design and simulation of the pile GHEs, improvement can also be achieved in simulating the temperature response of the borehole GHEs, especially for short time steps. [Copyright &y& Elsevier]

Abstract: This paper presents a heat and mass transfer simulation of an adsorber, taking into consideration the geometry of the heat exchanger and the diffusion in the adsorbent medium. In this model, an increment in the direction of heating/cooling fluid containing one (or more) fin pitch was considered. In the domain of this increment, the distribution of the adsorbent temperature was evaluated in the radial and axial directions. The model is validated by experimental data of different adsorbents, volume flows and temperatures. All data were collected in an adsorber test-bench at Fraunhofer ISE. As a result it was found a coefficient of multiple determination of around 0.94 and an error of 20% during the transient. Finally, the model was run on typical operation for cooling application and compared with data from literature. A numerical energy balance was also evaluated. In summary, the results obtained by a independent group shows the same range of confidence of the model developed here, in terms of the tendency of the curves and even the absolute values. [Copyright &y& Elsevier]

Abstract: In the present study, a 3D numerical simulation of a whole heat exchanger with middle-overlapped helical baffles is carried out by using commercial codes of GAMBIT 2.3 and FLEUNT 6.3. At first, the computational model and numerical method of the whole heat exchanger with middle-overlapped helical baffles is presented in detail, and parallel computation mode is adopted for the simulation of a whole heat exchanger with six cycles of the middle-overlapped helical baffles of 40° helical angle on a grid system of 13.5-million cells; second, the validation of the computational model is performed by comparing the total pressure drop and average Nusselt number of the whole heat exchanger with experimental data. Reasonably good agreement is obtained, and the reasons causing to the discrepancy are analyzed. The shell-side fluid pressure and temperature fields of the whole area are then presented. Finally the cycle average Nusselt number of different cycle in the heat exchanger are compared and it is found that within the accuracy allowed in engineering computation, periodic model for one cycle can be used to investigate the heat transfer and pressure drop characteristics for different heat exchanger to save computational source. The companion paper will provide details of simulation results using the periodic model for different helical angles and different structures of helical baffles. [Copyright &y& Elsevier]

Abstract: In the paper, numerical and experimental analyses of heat and mass transfer during frost formation on a fin-and-tube heat exchanger have been presented. Modelling of the frost formation on cold surfaces placed in a humid air stream, requires a complex mathematical approach. A transient two-dimensional mathematical model of frost formation has been developed. The applied mathematical model has been defined using governing equations for the boundary layer that include air and frost sub-domains as well as a boundary condition on the air–frost interface. The mathematical model with initial and boundary conditions has been discretised according to the finite volume method and solved numerically using the SIMPLER algorithm for the velocity–pressure coupling. Results have shown that the frost layer formation significantly influences the heat transfer between air and fins. As a result of numerical calculations, time-wise frost thickness variations for different air humidities, temperatures and velocities have been presented. Using the developed mathematical model, the algorithm and the computer code, which have been experimentally validated, it is possible to predict a decrease of exchanged heat flux in the heat exchanger under frost growth conditions. [Copyright &y& Elsevier]

Abstract: The paper presents the geometry of infinite regular polyhedrons that can be used to construct the heat exchange units. The basic structural component of the infinite solid consists of six hexagons, which meet in the common vertex. The mathematical model of heat and mass transfer inside the labyrinth heat exchanger is shown. The first and the second Kirchhoff’s laws are used to simulate fluid flow distribution at hydraulic network created with connected basic solids. Heat balance equations are adopted to describe forced convection heat transfer inside developed heat exchanger. Good accordance among the experimental data and calculation results over whole simulation range is obtained. The efficiency and thermal characteristic of the labyrinth heat exchanger is presented in the form of graphs. [Copyright &y& Elsevier]