Search

Abstract: This paper discusses results of simulations conducted for non-contacting face seals showing the influence of the operational parameters on the distributions of temperature in the structural elements and the fluid film separating the sealing rings. The mathematical model developed for noncontacting face seals consists of cross-coupled differential equations with partial derivatives. We solved it analytically, taking into account various boundary conditions. The heat equations were solved using the method of separation of variables. The derived relationships were based on Bessel functions of the first and second kinds. By defining the relationships describing the distributions of temperature in the sealing rings and the fluid film separating them, we could determine the effect of the operational parameters on the variability of temperature fields. Confirmation of the simulation results with experimental data is essential to better recognize the phenomena taking place in the sealing assembly and improve the design of non-contacting seals so that they can be used in various industrial applications. In this paper, we also describe a specially designed test stand for compensation of the misalignment of the flexibly mounted ring and automatic control of the radial clearance height. The test stand can also be used to verify the results of analytical studies. [Copyright &y& Elsevier]

Abstract: Adequate modeling of radiation heat transfer is important in CFD simulation of coal gasification process. In an entrained-flow gasifer, the non-participating effect of coal particles, soot, ashes, and reactive gases could significantly affect the temperature distribution in the gasifier and hence affects the local reaction rate and life expectancy of wall materials. For slagging type gasifiers, radiation further affects the forming process of corrosive slag on the wall which can expedite degradation of the refractory lining in the gasifier. For these reasons, this paper focuses on investigating applications of five different radiation models to coal gasification process, including Discrete Transfer Radiation Model (DTRM), P-1 Radiation Model, Rosseland Radiation Model, Surface-to-Surface (S2S) Radiation Model, and Discrete Ordinates (DO) Radiation Model. The objective is to identify the pros and cons of each model’s applicability to the gasification process and determine which radiation model is most appropriate for simulating the process in entrained-flow gasifiers. The Eulerian–Lagrangian approach is applied to solve the Navier–Stokes equations, nine species transport equations, and seven global reactions consisting of three heterogeneous reactions and four homogeneous reactions. The coal particles are tracked with the Lagrangian method. Six cases are studied—one without the radiation model and the other five with different radiation models. The result reveals that the various radiation models yield uncomfortably large uncertainties in predicting syngas composition, syngas temperature, and wall temperature. The Rosseland model does not yield reasonable and realistic results for gasification process. The DTRM model predicts very high syngas and wall temperatures in the dry coal feed case. In the one-stage coal slurry case, DTRM result is close to the S2S result. The P1 method seems to behave stably and is robust in predicting the syngas temperature and composition; it yields the result most close to the mean, but it seems to underpredict the gasifier’s inner wall temperature. [Copyright &y& Elsevier]

Abstract: This paper investigates the numerical simulation of non-Fourier transient heat transfer in a two-dimensional sub-100nm metal-oxide-semiconductor field-effect transistor (MOSFET). The dual-phase-lag (DPL) model with a specific normalization procedure is introduced for the modeling of nanoscale heat transport. The boundary conditions are selected similar to what existed in a real MOSFET device, both uniform and non-uniform heat generations within the transistor are applied, and the end parts of the top boundary which are in contact with the metallic material are left open. A temperature-jump boundary condition is used on all boundaries in order to consider the boundary phonon scattering at micro and nanoscale. A three-level finite difference scheme has been employed to generate the numerical results which are illustrated for a silicon sub-100nm MOSFET corresponding to the Knudsen number of 10. The results are presented at real times less than 50ps to avoid the three-dimensional effects. It is concluded that the combination of the DPL model with mixed-type temperature boundary condition is able to predict the heat flux and temperature distribution obtained from the Boltzmann transport equation (BTE) more accurate than the ballistic-diffusive equations (BDE). After verification of our results, the thermal field and the hotspot temperature within the bulk silicon are presented and the effect of adding a layer of silicon-dioxide to the transistor on its thermal behavior has been investigated. [Copyright &y& Elsevier]

Abstract: This paper focuses on the investigation of the 3D mathematical model to simulate the coupled heat and liquid moisture transfer in hygroscopic porous fibrous media. The flow of the liquid moisture, the water vapor sorption/desorption by fibers and the diffusion of the water vapor are taken into account in this 3D model. Prediction-corrector method is used to solve the 3D governing equations. A series of computational results of the coupled heat and moisture transfer are obtained with the specific initial conditions and boundary conditions. The distribution of the water vapor concentration in the void spaces, the volume fraction of the liquid water in the void spaces, the distribution of the water content in fibers and the changes of the temperature in porous fibrous media are computed. It is shown that the effects of the gravity and capillary actions are significant in hygroscopic porous fibrous media. The comparison with the experimental measurements shows the reasonable agreement between the two. The results illustrate that the 3D model of the coupled heat and liquid moisture transfer in hygroscopic porous fibrous media is satisfactory. [Copyright &y& Elsevier]

Abstract: In the present study, a 3D numerical simulation of a whole heat exchanger with middle-overlapped helical baffles is carried out by using commercial codes of GAMBIT 2.3 and FLEUNT 6.3. At first, the computational model and numerical method of the whole heat exchanger with middle-overlapped helical baffles is presented in detail, and parallel computation mode is adopted for the simulation of a whole heat exchanger with six cycles of the middle-overlapped helical baffles of 40° helical angle on a grid system of 13.5-million cells; second, the validation of the computational model is performed by comparing the total pressure drop and average Nusselt number of the whole heat exchanger with experimental data. Reasonably good agreement is obtained, and the reasons causing to the discrepancy are analyzed. The shell-side fluid pressure and temperature fields of the whole area are then presented. Finally the cycle average Nusselt number of different cycle in the heat exchanger are compared and it is found that within the accuracy allowed in engineering computation, periodic model for one cycle can be used to investigate the heat transfer and pressure drop characteristics for different heat exchanger to save computational source. The companion paper will provide details of simulation results using the periodic model for different helical angles and different structures of helical baffles. [Copyright &y& Elsevier]

Abstract: The paper presents the geometry of infinite regular polyhedrons that can be used to construct the heat exchange units. The basic structural component of the infinite solid consists of six hexagons, which meet in the common vertex. The mathematical model of heat and mass transfer inside the labyrinth heat exchanger is shown. The first and the second Kirchhoff’s laws are used to simulate fluid flow distribution at hydraulic network created with connected basic solids. Heat balance equations are adopted to describe forced convection heat transfer inside developed heat exchanger. Good accordance among the experimental data and calculation results over whole simulation range is obtained. The efficiency and thermal characteristic of the labyrinth heat exchanger is presented in the form of graphs. [Copyright &y& Elsevier]

Abstract: This paper presents the advantages of a Branch Eigenmodes Reduced Model used in a control process of a heating system. The experimental setup is a 3D heat conductive system in which a heat source is set. First, the reduced model is used to solve the non-linear Inverse Heat Conduction Problem: identification of the heat source strength variations from time-varying temperatures. Then, the reduced model is used to control hot points in the system. The objective of the method is to allow sequential temperature control by decreasing the computation time necessary for the simulation. [Copyright &y& Elsevier]