Search

The focus of whey processing has been changed from waste treatment to the production of valuable products owing to the advancement of membrane technology. Producing high quality whey products at low energy consumption entails novel techniques for whey concentration. This study proposes forward osmosis (FO) as a potential approach to concentrate whey protein solutions, which is superior to the concentration via reverse osmosis (RO), mainly owing to the low hydraulic pressure during FO process. In particular, this work validated the feasibility of FO-based whey concentration using high-performance hollow fiber membranes that were fabricated in-house. The investigation focused on the effects of various operating conditions on the concentration performance. The experimental results reveal that optimal concentration efficiency would be achieved by appropriately choosing the cross-flow velocity, draw solution concentration and the maximum attainable concentration of whey protein solution. Especially, the flux decline behaviour as a function of the whey protein concentration in the feed solution indicated rapid formation of a polarized or gel foulant layer at the membrane surface. The proposed mechanism was supported by the investigation of physical cleaning with water, showing that the post-process cleaning after the concentration cycle was able to recover the membrane performance, whereas the intermediate cleaning during one concentration cycle had little impact on the concentration efficiency enhancement. This study has practical significance for the application of FO in the concentration of dairy streams and other liquid foods. [ABSTRACT FROM AUTHOR]

Abstract: Due to the unique properties of amphiphilic Pluronic block copolymers, they have been blended with other polymers such as PVDF to prepare membranes. Considering the stability issue, the strong pore-forming ability of Pluronic F127, and the mechanical strength of the resultant membranes, Pluronic/LiCl mixed additive consisting of a very low concentration of Pluronic has been used in this study. The effects of spinning conditions on PVDF hollow fiber fabrication have also been studied. It is found that the use of merely 0.2wt% of Pluronic is sufficient to impose significant impacts on the morphology, filtration performance, and mechanical properties of the resultant fibers. Hollow fibers spun using higher coagulant temperature, higher take-up speed, and water as the bore fluid exhibit better mechanical properties and filtration performance. PVDF hollow fiber membranes with PWP of 1180L/m2 hMPa and MWCO of 5kDa were obtained when spun with optimized spinning conditions and using 3wt% of LiCl and 0.2wt% of Pluronic as the mixed additive. The fibers can withstand a pressure of 0.55MPa from the lumen. [Copyright &y& Elsevier]

This report demonstrates the fabrication of a composite hollow fiber membrane that efficiently recovers dissolved methane (dCH 4) from anaerobic wastewater treatment effluents via membrane contactor (MC) process. We first fabricated highly porous hollow fiber membranes (∼85% porosity) using polyvinylidene difluoride (PVDF). Then, we coated the whole structure (bulk), or lumen side of PVDF supports with polydimethylsiloxane (PDMS), a hydrophobic polymer possessing high gas permeability. The adjustment of the concentration of PDMS precursor mix could effectively serve for tuning the performance characteristics of MC membranes and helped suppress membrane wetting, a major performance-reducing factor. Despite their denser skin layers, the lumen-modified membranes demonstrated superior dCH 4 recovery flux. Mass transfer analyses have confirmed the importance of preserving bulk porosity while coating the membrane surfaces. The long-term performance tests performed using actual anaerobic effluents suggested that the PDMS coating did not accelerate fouling, such that the lumen-modified MC membranes showed an almost steady flux for 8 days with an anaerobic membrane bioreactor effluent. A high-strength effluent, obtained from an up-flow anaerobic sludge blanket reactor, induced faster fouling. However, we observed only a ∼20% flux decline in a 10-day operation. Thus, we propose that the designed PDMS-PVDF composite membranes are promising for industrial practices. Image 1 • We prepared PDMS-coated PVDF porous hollow fiber membranes for membrane contacting. • Both lumen- and bulk-modified PVDF membranes were successful in methane recovery. • Lumen-modified PDMS-PVDF membrane outperformed commercial PP and PDMS membranes. • Lumen-modified PVDF achieved long-term performance with actual anaerobic effluents. [ABSTRACT FROM AUTHOR]

In this study, the glutaraldehyde (GA) crosslinking was adopted in combination of layer-by-layer (LBL) polyelectrolyte deposition to develop a novel hollow fiber NF membrane with low-pressure water softening capability for synthesized hard water containing divalent counterion SO 4 2− . The challenges for the new membrane include (a) the presence of SO 4 2− in the feed water, which tends to deteriorate positively charged NF membrane retention to divalent ions; (b) high salinity feed water up to 10,000 ppm total dissolved salt (TDS); (c) 2 bar operating pressure that requires the membrane to have a good Mg 2+ /Na + selectivity and less mass transfer resistance in the substrate; and (d) better separation performance as compared with the state-of-the-art and commercial NF membranes. Based on the membrane characterization results, the possible structure of the deposited layers and the effect of GA crosslink was proposed. It was found that the crosslinking could tighten the membrane surface pores with increased hydrophilicity while the membrane surface charge was reduced. Therefore, mainly based on the size exclusion, the crosslinked LBL*1.5C membrane showed more than 10 LMH/bar permeability with above 95% rejection to each of 1000 ppm MgCl 2 , MgSO 4 and Na 2 SO 4 solution under 2 bar pressure. It was also proved to be more suitable for the low-pressure water softening application at 2 bar in all tested feed water with the presence of SO 4 2− and TDS up to 10,000 ppm in terms of both permeability and hardness removal efficiency when compared with commercial NF 270 and NF 90 membranes. [ABSTRACT FROM AUTHOR]

Abstract The combination of nonsolvent and thermally induced phase separation (N-TIPS) method has shown promising ability in harvesting the features from the nonsolvent induced phase separation (NIPS) and thermally induced phase separation (TIPS) processes for developing membranes with a tailorable surface pore structure. However, previous approaches have been subjected to either the formation of macrovoids or dense layer due to the dominant NIPS effect, or required sophisticated instruments and operation skills. In this work, a facile attempt was carried out to fabricate novel polyvinylidene fluoride (PVDF) hollow fiber membranes with tunable surface pore structure while maintaining the narrow pore size distribution and mechanical strength. A modified N-TIPS method was developed by using mixed diluents: dimethyl phthalate (DMP) as a water-immiscible poor solvent for TIPS process, and triethyl phosphate (TEP) as a water-miscible neutral solvent to bridge the TIPS and NIPS processes. To further control the membrane formation especially near the membrane surface, an amphiphilic additive Pluronic F127 was also added as a potential pore-former and surface hydrophilicity modifier. PVDF hollow fiber membranes with a highly porous structure and a narrow pore size distribution were successfully synthesized by using TEP and Pluronic F127 in the N-TIPS process. The mechanism of N-TIPS process was thoroughly discussed. The water permeability of the membrane increased significantly from 389 ± 30–922 ± 36 L m–2 h–1 bar–1, with overall porosity improved from 50 ± 2.2–69 ± 2.9%, and a mean pore size of ~ 0.18 µm. The membranes produced by N-TIPS method also exhibited a good tensile strength ranging from 5.6 ± 0.1–6.5 ± 0.2 MPa, showing a great potential for a broad range of water applications after further modifications. Besides, the formation of piezoelectric β-phase crystals of the PVDF membrane was observed when the mixed diluent was used, which sheds light on the possible applications of resultant membranes in electrochemical separation process. Highlights • PVDF hollow fiber membranes were developed via a modified N-TIPS method using mixed diluents together with Pluronic F127. • The NIPS effect could be induced at the outer surface with the co-occurrence of TIPS process along the bulk of membrane. • The surface pore structure of membrane could be tailored without the formation of mechanically weak macrovoids. • The prepared membranes possess a hydrophobic surface with good porosity, permeability and mechanical strength. [ABSTRACT FROM AUTHOR]

Pressure retarded osmosis (PRO) is a promising energy harvesting technique. However, when polymeric hollow fiber membrane is used for the PRO process, the mechanical strength of the membrane is a big concern. As hollow fiber membrane is self-supported and due to its polymeric nature, it may gradually deform over time under high pressure loading, or membrane “creeping” will occur. Current work is the first attempt to analyze the membrane creeping phenomenon of a novel thin film composite (TFC) hollow fiber. The membrane creeping was evaluated via nanoindentation by using atomic force microscope (AFM). A non-stop 200-hour PRO test and integrity check, which have not been reported previously, were carried out to investigate the membrane performance under various operating pressures. The results show that the membrane is able to produce a stable power density output of 19.2 W/m 2 at 15.0 bar, using 1.0 M NaCl as the draw solution and DI water as the feed water. Membrane creeping was observed when the applied pressure exceeded the safe operation limit (or the flux turning point, where the membrane flux started to increase with increasing applied pressure in the PRO mode), which caused an irreversible damage to the membranes. This study identified safe and optimum operation conditions of the laboratory-made PRO hollow fiber membrane to achieve the most favorable PRO performance. It provides guidance for practical applications of polymeric hollow fiber membranes in PRO process. [ABSTRACT FROM AUTHOR]

The use of nanotechnology in water separation membranes is a promising approach to alleviate the global water crisis. Graphene oxide (GO) with its unique water transport property has exhibited high potential for application in the water treatment processes. In this study, we have designed and fabricated a novel nanofiltration (NF)-like GO surface deposited poly(amide-imide)–polyethyleneimine (PAI–PEI) hollow fiber membrane. The PAI hollow fiber substrate was prepared by phase inversion and modified with PEI to obtain a positively charged membrane surface. The negatively charged GO nanosheets were then electrostatically immobilized onto the membrane surface via an instant dip-coating to form the NF-like selective layer. Our results have shown that the GO nanosheets serve as effective selective barriers and can achieve higher water permeability up to 86% without compromising membrane selectivity when used to substitute part of the PEI cross-linked selective layer. This is attributed to the smaller hydrodynamic resistance of GO nanosheets and their ability to effectively narrow the pore size distribution. Moreover, shortening of the membrane modification time and better mechanical properties of the GO modified membrane can be attained by avoiding excessive PEI cross-linking. The GO deposition also exhibits good stability when subjected to a backwashing pressure of 100,000 Pa and a cross-flow rate of 600 mL/min, which corresponds to a velocity of 14 cm/s and a Reynolds number of ~870. These results have demonstrated a high potential of using this GO modified hollow fiber membrane for large scale water softening applications. [ABSTRACT FROM AUTHOR]

Municipal solid waste (MSW) gasification is an attractive waste-to-energy (WTE) technology with promise for future solid waste management, owing to the production of syngas which can be used as an alternative energy resource. However, quality of produced syngas is not meeting expectation. One promising solution is to use oxygen-enriched gas (OEG) to elevate produced syngas quality but producing OEG is costly. Herein, we demonstrated an asymmetric defect-free hollow fiber membrane made up of Matrimid® 5218 polyimide for scaling-up to 2-inch membrane modules. Our modules have an effective surface area up to 2.6 m2 with a packing density of up to 44% to produce OEG of 45% O 2 purity. The 2-inch membrane module was integrated into a lab-scale gasification process to produce syngas using refuse derived fuel (RDF) generated from MSWs collected from the university campus. Prior to this, the lab-scale gasification was first optimized by tuning the gasification temperature, O 2 purity and equivalence ratio (ER). Then, MSW gasification using membrane-based OEG was carried out, and compared against air gasification and synthetic OEG of the same O 2 purity. Our results showed that, at O 2 purity of 45%, gasification temperature of 900 °C and ER of 0.15, the quality of produced syngas was elevated with a lower heating value (LHV) of 9.15 MJ/m3 and H 2 /CO ratio of 1.43, which was substantially higher than air gasification with LHV and H 2 /CO ratio reported at 5.38 MJ/m3 and 0.81, respectively. Gasification results for membrane-based OEG and synthetic OEG were also comparable, while process simulation evidence suggested that membrane-based separation was at least 2-fold less energy-intensive than cryogenic distillation and pressure swing adsorption. Overall, this proof-of-concept successfully demonstrates the viability and competitiveness of membrane process for producing OEG at medium O 2 purity (i.e. , 40–50%) to support MSW gasification for WTE conversion. [Display omitted] • Hollow fiber membrane modules with up to 2.6 m2 surface area were developed. • OEG with O 2 purity of c.a. 45% can be produced at close to 2 L/min flow rate. • Membrane-based OEG gasification produces syngas with 70% higher LHV as that of air gasification. • Membrane-based OEG produces syngas with comparable LHV as that of synthetic OEG. • Simulation shows that membrane separation is less energy-intensive for producing OEG of medium purity. [ABSTRACT FROM AUTHOR]