Search

A piston slap is one of the main vibration sources of the reciprocating machinery. Much work has been done in this field, most of which was based on a constant rotating speed. However, in practice, the speed of a crankshaft may always fluctuate due to the uneven load or excitation. The inertia forces of moving components are much different at the fluctuating rotating speed comparing with that at a constant speed. In this paper, the piston slap and the induced vibration are analyzed based on the instantaneous angular speed measured on a single-cylinder reciprocating compressor. Firstly, the dynamics of a crank-connecting rod mechanism is analyzed based on the measured instantaneous angular speed which contains the torsional vibration of the air compressor. The time histories of piston slap impact forces considering and without considering torsional vibration are compared. Then, in order to correlate the piston slap impact with the slap-induced vibration, the corresponding transfer functions between the middle stroke of the outer surface of the cylinder liner and the excitation points are measured. And the excitation force on the main bearing is also taken into account to bring the simulation closer to the experimental results. The effects of a torsional vibration on the vibration of the cylinder liner are analyzed, and the simulation results show that the torsional vibration is a factor that must be taken into account in the vibration analysis of the single-cylinder reciprocating compressor. [ABSTRACT FROM AUTHOR]

Torsional vibration of shafts is a very important problem in engineering, in particular in ship engines and aeroengines. Due to their high levels of integration and complexity, it is hard to get their accurate structural data or accurate modal data. This lack of data is unhelpful to vibration control in the form of structural modifications. Besides, many parts in shaft systems are not allowed to be modified such as rotary inertia of a pump or an engine, which is designed for achieving certain functions. This paper presents a strategy for torsional vibration control of shaft systems in the form of structural modifications based on receptances, which does not need analytical or modal models of the systems under investigation. It only needs the torsional receptances of the system, which can be obtained by testing simple auxiliary structure attached to relevant locations of the shaft system and using the finite element model (FEM) of the simple structure. An optimization problem is constructed to determine the required structural modifications, based on the actual requirements of modal frequencies and mode shapes. A numerical experiment is set up and the influence of several system parameters is analysed. Several scenarios of constraints in practice are considered. The numerical simulation results demonstrate the effectiveness of this method and its feasibility in solving torsional vibration problems in practice. [ABSTRACT FROM AUTHOR]

To analyze the torsional vibration of a diesel engine shaft, the torsional stiffness of the flexible coupling is a key kinetic parameter. Since the material properties of the elastic element of the coupling might change after a long-time operation due to the severe working environment or improper use and the variation of such properties will change dynamic feature of the coupling, it will cause a relative large calculation error of torsional vibration to the shaft system. Moreover, the torsional stiffness of the elastic coupling is difficult to be determined, and it is inappropriate to measure this parameter by disassembling the power unit while it is under normal operation. To solve these problems, this paper comes up with a method which combines the torsional vibration test with the calculation of the diesel shafting and uses the inherent characteristics of shaft torsional vibration to identify the dynamic stiffness of the elastic coupling without disassembling the unit. Analysis results show that it is reasonable and feasible to identify the elastic coupling dynamic torsional stiffness with this method and the identified stiffness is accurate. Besides, this method provides a convenient and practical approach to examine the dynamic behavior of the long running elastic coupling. [ABSTRACT FROM AUTHOR]

An improved Fourier expansion-based differential quadrature (DQ) algorithm is proposed to study the free vibration behavior of truncated conical shells with different boundary conditions. The original function is expressed as the Fourier cosine series combined with close-form auxiliary functions. Those auxiliary functions are introduced to ensure and accelerate the convergence of series expansion. The grid points are uniformly distributed along the space. The weighting coefficients in the DQ method are easily obtained by the inverse of the coefficient matrix. The derivatives in both the governing equations and the boundaries are discretized by the DQ method. Natural frequencies and modal shapes can be easily obtained by solving the numerical eigenvalue equations. The accuracy and stability of this proposed method are validated against the results in the literature and a very good agreement is observed. The centrosymmetric properties of these newly proposed weighting coefficients are also validated. Studies on the effects of semivertex angle and the ratio of length to radius are reported. [ABSTRACT FROM AUTHOR]

Vibration isolation systems are widely employed in automotive, marine, aerospace, and other engineering fields. Accurate input forces are of great significance for mechanical design, vibration prediction, and structure modification and optimization. One-stage vibration isolation system including engine, vibration isolators, and flexible supporting structure is modeled theoretically in this paper. Input excitation acting on the vibration isolation system is reconstructed using dynamic responses measured on engine and supporting structure under in-suit condition. The reconstructed forces reveal that dynamic responses on rigid body are likely to provide more accurate estimation results. Moreover, in order to improve the accuracy of excitation reconstructed by dynamic responses on flexible supporting structure, auto/cross-power spectral density function is utilized to reduce measurement noise. [ABSTRACT FROM AUTHOR]