Search

This paper describes the successes and failures after 4 years of continuous operation of a network of sensors, communicating nodes, and gateways deployed on the Etna Volcano in Sicily since 2019, including a period of Etna intense volcanic activity that occurred in 2021 and resulted in over 60 paroxysms. It documents how the installation of gateways at medium altitude allowed for data collection from sensors up to the summit craters. Most of the sensors left on the volcanic edifice during winters and during this period of intense volcanic activity were destroyed, but the whole gateway infrastructure remained fully operational, allowing for a very fruitful new field campaign two years later, in August 2023. Our experience has shown that the best strategy for IoT deployment on very active and/or high-altitude volcanoes like Etna is to permanently install gateways in areas where they are protected both from meteorological and volcanic hazards, that is mainly at the foot of the volcanic edifice, and to deploy temporary sensors and communicating nodes in the more exposed areas during field trips or in the summer season. [ABSTRACT FROM AUTHOR]

The detection ability of SO2 cameras has been improved effectively, while the calibration is still the main factor that limits their measurement accuracy. This paper presents a nonlinear calibration theory by considering the effect of light dilution due to the path radiance as well as the dependence of plume aerosol on scattering wavelength. This new spectral calibration method is used to retrieve the SO2 column density and emission rate of the Etna volcano. Results show that, compared with the DOAS calibration approach, the inversion error can be reduced by 13% if the new spectral calibration is adopted. The superiority of the proposed method will become more obvious for long-distance detection of optically thick plumes. [ABSTRACT FROM AUTHOR]

Volcanic plume height is one the most important features of explosive activity; thus, it is a parameter of interest for volcanic monitoring that can be retrieved using different remote sensing techniques. Among them, calibrated visible cameras have demonstrated to be a promising alternative during daylight hours, mainly due to their low cost and low uncertainty in the results. However, currently these measurements are generally not fully automatic. In this paper, we present a new, interactive, open-source MATLAB tool, named 'Plume Height Analyzer' (PHA), which is able to analyze images and videos of explosive eruptions derived from visible cameras, with the objective of automatically identifying the temporal evolution of eruption columns. PHA is a self-customizing tool, i.e., before operational use, the user must perform an iterative calibration procedure based on the analysis of images of previous eruptions of the volcanic system of interest, under different eruptive, atmospheric and illumination conditions. The images used for the calibration step allow the computation of ad hoc expressions to set the model parameters used to recognize the volcanic plume in new images, which are controlled by their individual characteristics. Thereby, the number of frames used in the calibration procedure will control the goodness of the model to analyze new videos/images and the range of eruption, atmospheric, and illumination conditions for which the program will return reliable results. This also allows improvement of the performance of the program as new data become available for the calibration, for which PHA includes ad hoc routines. PHA has been tested on a wide set of videos from recent explosive activity at Mt. Etna, in Italy, and may represent a first approximation toward a real-time analysis of column height using visible cameras on erupting volcanoes. [ABSTRACT FROM AUTHOR]

The green transformation of the built environment is aimed at improving sustainability and can be supported by digitalization, which has become a significant tool to support the supply, integration, and management of information throughout the construction life cycle. In addition, climate change highly affects human comfort in the built environment and different strategies should be evaluated for adapting cities. This paper developed a digital workflow by integrating existing tools (i.e., Grasshopper, Ladybug, Honeybee, and Dragonfly) to evaluate how different green infrastructure strategies affected the thermal comfort by reducing the UTCI. The workflow was applied to a typical historical urban context (Catania, South of Italy), consisting of a square surrounded by three-floor buildings. Three basic scenarios were created that depended on the pavement material used in the built environment: a black stone pavement (reference material from Mount Etna), a permeable pavement, and grass. These three scenarios were combined with different green infrastructure strategies: tree pattern on the square, green walls and green roofs on the surrounding buildings, and the integrations of all these above-mentioned strategies. The results demonstrated that the integration of different green strategies (a grass square instead of pavement, with trees, and green walls and green roofs) increased the thermal comfort by reducing the UTCI by more than 8 °C compared to the existing urban context (black stone pavement and building envelope). However, this temperature reduction was highly affected by the location of the human body into the urban context and by the evaporation rates from vegetation. The workflow developed will be useful for designers to evaluate the effectiveness of different green strategies during the early-design stage in mitigating and adapting cities to climate change. [ABSTRACT FROM AUTHOR]

In this study, we focus on the eruption of Mount Etna on Christmas 2018, which emitted great amounts of S O 2 from 24th to 30th December into the free troposphere. Simulations based on two different estimations of S O 2 emission fluxes are conducted with the chemistry-transport model MOCAGE in order to study the impact of these estimations on the volcanic plume modeling. The two flux emissions used are retrieved (1) from the ground-based network FLAME, located on the flank of the volcano, and (2) from the spaceborne instrument SEVIRI onboard the geostationary satellite MSG. Multiple spaceborne observations, in the infrared and ultraviolet bands, are used to evaluate the model results. Overall, the model results match well with the plume location over the period of the eruption showing the good transport of the volcanic plume by the model, which is linked to the use of a realistic estimation of the altitude of injection of the emissions. However, there are some discrepancies in the plume concentrations of S O 2 between the two simulations, which are due to the differences between the two emission flux estimations used that are large on some of the days. These differences are linked to uncertainties in the retrieval methods and observations used to derive S O 2 volcanic fluxes. We find that the uncertainties in the satellite-retrieved column of S O 2 used for the evaluation of the simulations, linked to the instrument sensitivity and/or the retrieval algorithm, are sometimes nearly as large as the differences between the two simulations. This shows a limitation of the use of satellite retrievals of S O 2 concentrations to quantitatively validate modeled volcanic plumes. In the paper, we also discuss approaches to improve the simulation of S O 2 concentrations in volcanic plumes through model improvements and also via more advanced methods to more effectively use satellite-derived products. [ABSTRACT FROM AUTHOR]

During the last two decades, the Etna volcano has undergone several sequences of lava fountaining (LF) events that have had a major impact on road conditions, infrastructure and the local population. In this paper, we consider the LF episodes occurring between 2011 and 2022, calculating their erupted volumes using the images recorded by the monitoring thermal cameras and applying a manual procedure and a dedicated software to determine the lava fountain height over time, which is necessary to obtain the erupted volume. The comparison between the results indicates the two procedures match quite well, the main differences occurring when the visibility is poor and data are interpolated. With the aim of providing insights for hazard assessment, we have fitted some probabilistic models of both the LF inter-event times and the erupted volumes of pyroclastic material. In more detail, we have tested power-law distributions against log-normal, Weibull, generalised Pareto and log-logistic. Results show that the power-law distribution is the most likely among the alternatives. This implies the lack of characteristic scales for both the inter-event time and the pyroclastic volume, which means that we have no indication as to when a new episode of LF will occur and/or how much material will be erupted. What we can reasonably say is only that short inter-event times are more frequent than long inter-event times, and that LF characterised by small volumes are more frequent than LF with high volumes. However, if the hypothesis that magma accumulates on Etna at a rate of about 0.8 m 3 s − 1   holds, the material accumulated in the source region from the beginning of the observation period (2011) to the present (2022) has already been ejected. In simple terms, there is no accumulated magma in the shallow storage that is prone to be erupted in the near future. [ABSTRACT FROM AUTHOR]

In the last decade, video surveillance cameras have experienced a great technological advance, making capturing and processing of digital images and videos more reliable in many fields of application. Hence, video-camera-based systems appear as one of the techniques most widely used in the world for monitoring volcanoes, providing a low cost and handy tool in emergency phases, although the processing of large data volumes from continuous acquisition still represents a challenge. To make these systems more effective in cases of emergency, each pixel of the acquired images must be assigned to class labels to categorise them and to locate and segment the observable eruptive activity. This paper is focused on the detection and segmentation of volcanic ash plumes using convolutional neural networks. Two well-established architectures, the segNet and the U-Net, have been used for the processing of in situ images to validate their usability in the field of volcanology. The dataset fed into the two CNN models was acquired from in situ visible video cameras from a ground-based network (Etna_NETVIS) located on Mount Etna (Italy) during the eruptive episode of 24th December 2018, when 560 images were captured from three different stations: CATANIA-CUAD, BRONTE, and Mt. CAGLIATO. In the preprocessing phase, data labelling for computer vision was used, adding one meaningful and informative label to provide eruptive context and the appropriate input for the training of the machine-learning neural network. Methods presented in this work offer a generalised toolset for volcano monitoring to detect, segment, and track ash plume emissions. The automatic detection of plumes helps to significantly reduce the storage of useless data, starting to register and save eruptive events at the time of unrest when a volcano leaves the rest status, and the semantic segmentation allows volcanic plumes to be tracked automatically and allows geometric parameters to be calculated. [ABSTRACT FROM AUTHOR]

The Etna volcano is renowned worldwide for its extraordinary lava fountains that rise several kilometers above the vent and feed eruptive columns, then drift hundreds of kilometers away from the source. The Italian Istituto Nazionale di Geofisica e Vulcanologia-Osservatorio Etneo (INGV-OE) is responsible for the monitoring of Mt. Etna, and for this reason, has deployed a network of visible and thermal cameras around the volcano. From these cameras, INGV-OE keeps a keen eye, and is able to observe the eruptive activity, promptly advising the civil protection and aviation authorities of any changes, as well as quantifying the spread of lava flows and the extent of pyroclastic and ash plumes by using a careful analysis of the videos recorded by the monitoring cameras. However, most of the work involves analysis carried out by hand, which is necessarily approximate and time-consuming, thus limiting the usefulness of these results for a prompt hazard assessment. In addition, the start of lava fountains is often a gradual process, increasing in strength from Strombolian activity, to intermediate explosive activity, and eventually leading to sustained lava fountains. The thresholds between these different fields (Strombolian, Intermediate, and lava fountains) are not clear cut, and are often very difficult to distinguish by a manual analysis of the images. In this paper, we presented an automated routine that, when applied to thermal images and with good weather conditions, allowed us to detect (1) the starting and ending time of each lava fountain, (2) the area occupied by hot pyroclasts, (3) the elevation reached by the lava fountains over time, and (4) eventually, to calculate in real-time the erupted volume of pyroclasts, giving results close to the manual analysis but more focused on the sustained portion of the lava fountain, which is also the most dangerous. This routine can also be applied to other active volcanoes, allowing a prompt and uniform definition of the timing of the lava fountain eruptive activity, as well as the magnitude and intensity of the event. [ABSTRACT FROM AUTHOR]

Understanding the dynamics of mild explosive activity is a fundamental tool for hazard assessment at open conduit volcanoes. This is a particularly critical task for Etna volcano. Etna is in fact characterized by frequent, mild explosive activity, punctuated by lava flows and paroxysmal events ('lava fountains'), which, because of their greater impact, have been the main target for hazard studies, whereas more frequent Strombolian activity has been overlooked. As a result, their impact and associated hazards have been never quantified, despite the extensive monitoring and surveillance activities carried out on this volcano. In this paper, we analyze video recordings of a sequence of Strombolian explosions occurring at the summit craters of Mt. Etna, in Italy, in February 2020. Data were also integrated with a petrographic analysis of collected samples, and drone surveys were performed at the same time as the video recordings. We estimate the frequency of explosions (20–12 per min); particle exit speeds (1–50 m/s), and erupted mass (100–102 kg) of those explosions. A very regular, small-scale activity (marked by a single burst of gas breaking the magma free surface into bombs and lapilli fragments) was occasionally punctuated by larger explosions, (at least one every 5 min), with a longer duration, fed by larger magma volumes, and consisting of two to three distinct pulses followed by a stationary phase. We found that the repose times between explosions follows a log logistic distribution, which is in agreement with the behavior of open vent explosive activity. The four largest explosions of the sequence were analyzed in detail: they emitted particles with median diameters (Mdphi) ranging from −10.1 to −8.8 phi, with bimodal distributions. [ABSTRACT FROM AUTHOR]

The purpose of the present paper is to investigate the effects of variable eruption source parameters on volcanic plume transport in the Mediterranean basin after the paroxysm of Mount Etna on 23 November 2013. This paroxysm was characterized by a north-east transport of ash and gas, caused by a low-pressure system in northern Italy. It is evaluated here in a joint approach considering the WRF-Chem model configured with eruption source parameters (ESPs) obtained elaborating the raw data from the VOLDORAD-2B (V2B) Doppler radar system. This allows the inclusion of the transient and fluctuating nature of the volcanic emissions to accurately model the atmospheric dispersion of ash and gas. Two model configurations were considered: the first with the climax values for the ESP and the second with the time-varying ESP according to the time profiles of the mass eruption rate recorded by the V2B radar. It is demonstrated that the second configuration produces a considerably better comparison with satellite retrievals from different sensors platforms (Ozone Mapping and Profiler Suite, Meteosat Second-Generation Spinning Enhanced Visible and Infrared Imager, and Visible Infrared Imaging Radiometer Suite). In the context of volcanic ash transport dispersion modeling, our results indicate the need for (i) the use of time-varying ESP, and (ii) a joint approach between an online coupled chemical transport model like WRF-Chem and direct near-source measurements, such as those carried out by the V2B Doppler radar system. [ABSTRACT FROM AUTHOR]

On 13 December 2020, Etna volcano entered a new eruptive phase, giving rise to a number of paroxysmal episodes involving increased Strombolian activity from the summit craters, lava fountains feeding several-km high eruptive columns and ash plumes, as well as lava flows. As of 2 August 2021, 57 such episodes have occurred in 2021, all of them from the New Southeast Crater (NSEC). Each paroxysmal episode lasted a few hours and was sometimes preceded (but more often followed) by lava flow output from the crater rim lasting a few hours. In this paper, we use remote sensing data from the ground and satellite, integrated with ground deformation data recorded by a high precision borehole strainmeter to characterize the 12 March 2021 eruptive episode, which was one of the most powerful (and best recorded) among that occurred since 13 December 2020. We describe the formation and growth of the lava fountains, and the way they feed the eruptive column and the ash plume, using data gathered from the INGV visible and thermal camera monitoring network, compared with satellite images. We show the growth of the lava flow field associated with the explosive phase obtained from a fixed thermal monitoring camera. We estimate the erupted volume of pyroclasts from the heights of the lava fountains measured by the cameras, and the erupted lava flow volume from the satellite-derived radiant heat flux. We compare all erupted volumes (pyroclasts plus lava flows) with the total erupted volume inferred from the volcano deflation recorded by the borehole strainmeter, obtaining a total erupted volume of ~3 × 106 m3 of magma constrained by the strainmeter. This volume comprises ~1.6 × 106 m3 of pyroclasts erupted during the lava fountain and 2.4 × 106 m3 of lava flow, with ~30% of the erupted pyroclasts being remobilized as rootless lava to feed the lava flows. The episode lasted 130 min and resulted in an eruption rate of ~385 m3 s−1 and caused the formation of an ash plume rising from the margins of the lava fountain that rose up to 12.6 km a.s.l. in ~1 h. The maximum elevation of the ash plume was well constrained by an empirical formula that can be used for prompt hazard assessment. [ABSTRACT FROM AUTHOR]

The growth of Mount Etna volcano reflects the superimposition of various eruptive centers, the most voluminous of which is the Ellittico, whose stratigraphic sequence is well exposed on the steep walls of Valle del Bove. The uppermost levels of the sequence have been sampled and investigated through a new set of geochemical data on mineral phases and bulk rock. Sampled rocks display a marked bimodality with aphyric banded trachyandesites, which are some of the most evolved and rare products of the entire Etnean succession (SiO2 58–60 wt.%), intercalated in plagioclase rich porphyritic mugearites (SiO2 49–50 wt.%, P.I. 35–40). In this paper, we provide a detailed textural, mineralogical, and chemical characterization of these products, providing a new interpretative model for their genesis and significance in the context of the Etnean system. Our approach discusses, in a critical way, the "classic" fractional crystallization model of magmas, not supported by field evidence, and proposes a novel hypothesis in which the aphyric-banded trachyandesites represent be the primary products of a gas-induced partial melting of hypabyssal sills and dykes. This hypothesis represents a step towards a comprehensive description of igneous systems that takes into account not exclusively the evolution of basaltic melts, but also the role of volatile contributions in governing volcanic behavior. [ABSTRACT FROM AUTHOR]

Accurate tracking and forecasting of ash dispersal in the atmosphere and quantification of its uncertainty are of fundamental importance for volcanic risk mitigation. Numerical models and satellite sensors offer two complementary ways to monitor ash clouds in real time, but limits and uncertainties affect both techniques. Numerical forecasts of volcanic clouds can be improved by assimilating satellite observations of atmospheric ash mass load. In this paper, we present a data assimilation procedure aimed at improving the monitoring and forecasting of volcanic ash clouds produced by explosive eruptions. In particular, we applied the Local Ensemble Transform Kalman Filter (LETKF) to the results of the Volcanic Ash Transport and Dispersion model HYSPLIT. To properly simulate the release and atmospheric transport of volcanic ash particles, HYSPLIT has been initialized with the results of the eruptive column model PLUME-MoM. The assimilation procedure has been tested against SEVIRI measurements of the volcanic cloud produced during the explosive eruption occurred at Mt. Etna on 24 December 2018. The results show how the assimilation procedure significantly improves the representation of the current ash dispersal and its forecast. In addition, the numerical tests show that the use of the sequential Ensemble Kalman Filter does not require a precise initialization of the numerical model, being able to improve the forecasts as the assimilation cycles are performed. [ABSTRACT FROM AUTHOR]

The Etna flank eruption that started on 24 December 2018 lasted a few days and involved the opening of an eruptive fissure, accompanied by a seismic swarm and shallow earthquakes, significant SO2 flux release, and by large and widespread ground deformation, especially on the eastern flank of the volcano. Lava fountains and ash plumes from the uppermost eruptive fissure accompanied the opening stage, causing disruption to Catania International Airport, and were followed by a quiet lava effusion within the barren Valle del Bove depression until 27 December. This was the first flank eruption to occur at Etna in the last decade, during which eruptive activity was confined to the summit craters and resulted in lava fountains and lava flow output from the crater rims. In this paper, we used ground and satellite remote sensing techniques to describe the sequence of events, quantify the erupted volumes of lava, gas, and tephra, and assess volcanic hazards. [ABSTRACT FROM AUTHOR]

This paper addresses the problem of interferometric noise reduction in Synthetic Aperture Radar (SAR) interferometry based on sparse and redundant representations over a trained dictionary. The idea is to use a Proximity-based K-SVD (ProK-SVD) algorithm on interferometric data for obtaining a suitable dictionary, in order to extract the phase image content effectively. We implemented this strategy on both simulated as well as real interferometric data for the validation of our approach. For synthetic data, three different training dictionaries have been compared, namely, a dictionary extracted from the data, a dictionary obtained by a uniform random distribution in [ − π , π ] , and a dictionary built from discrete cosine transform. Further, a similar strategy plan has been applied to real interferograms. We used interferometric data of various SAR sensors, including low resolution C-band ERS/ENVISAT, medium L-band ALOS, and high resolution X-band COSMO-SkyMed, all over an area of Mt. Etna, Italy. Both on simulated and real interferometric phase images, the proposed approach shows significant noise reduction within the fringe pattern, without any considerable loss of useful information. [ABSTRACT FROM AUTHOR]