Search

This paper presents new metrics to measure the effect of thermal mass on the energy required to heat and cool buildings. Previous studies have been flawed as they have not considered the interaction between intermittent occupancy and thermal mass, which has a significant impact on overall energy use. However, existing parameters do not adequately capture these effects, so the new metrics developed in this paper are used to analyse the impact of thermal mass in hot climates with active cooling, and cold climates with active heating. The results agree with existing literature that high thermal mass structures are likely to be effective in hot climates; however, in cold climates the drawbacks of high thermal mass likely outweigh the advantages, and high thermal mass can cause an increase in energy use. This finding has implications for the design of buildings in cold climates, and contradicts the commonly-held assumption that high thermal mass is correlated with low energy use. The new metrics (transient energy ratio and effective U -value) provide a generalisable method to quantify these effects. They are further used here to analyse the dynamic performance of heavily insulated buildings and show that high thermal mass often leads to higher energy use in cold climates. [ABSTRACT FROM AUTHOR]

In a central heating, ventilation, and air conditioning (HVAC) system, the set-points for several local control loops have a significant influence on the overall energy performance of the system. Real-time optimization (RtOpt) of those set-points has therefore been widely studied. However, due to the nonlinear dynamics of the HVAC system as well as the constraints associated with the system operation, real-time optimization always suffers from a heavy on-line computational load when those set-points are optimized simultaneously. To overcome this problem, multiplexed real-time optimization (MRtOpt) has been developed, which optimizes only one set-point at a time but with a faster optimization frequency. Because frequently resetting the set-points introduces artificial disturbances into the local control loops and may deteriorate the system stability, this paper presents a study to enhance the system stability of the multiplexed real-time optimization by integrating a degree of freedom (DOF) based set-point reset to renew the set-points instead of the conventional step-change set-point reset. The control performance of the integrated strategy was investigated using case studies. The results showed that around 10% of the energy saving was achieved by the proposed method compared with a method without real-time optimization. When compared with the conventional real-time optimization method, the proposed method resulted in around 70% computational load reduction, and over 26% reduction in the tracking errors of the local control loops. [ABSTRACT FROM AUTHOR]

Abstract: Evaluating a building’s performance usually requires a high number of sensors especially if individual rooms are analyzed. This paper introduces a simple and scalable model-based virtual sensor that allows analysis of a buildings’ heat consumption down to room level using mainly simple temperature sensors. The approach is demonstrated with different sensor models for a case study of a building that contains a hybrid HVAC system and uses fossil and renewable energy-sources. The results show that, even with simple sensor models, reasonable estimations of rooms’ heat consumption are possible and that rooms with high heat consumption are identified. Further, the paper illustrates how virtual sensors for thermal comfort can support the decision making to identify the best ways to optimize building system efficiency while reducing the building monitoring cost. [Copyright &y& Elsevier]

Abstract: The performance of different HVAC systems varies when coupled with different buildings. This paper examines the relationship between building heating and cooling load and subsequent energy consumption with different HVAC systems. Two common HVAC systems in use throughout the UK office building stock, variable air volume (VAV) system and fan coil (FC) with dedicated outside air system, have been coupled with a typical narrow plan office building with and without daylight control and for both cellular and open plan. The results presented in this paper clearly indicate that it is not possible to form a reliable judgment about building energy performance based only on building heating and cooling loads. For the two investigated systems, variable air volume system and fan coil with dedicated outside air system, the difference between system demand and building demand varied from over −40% to almost +30% for cooling and between −20% and +15% for heating. If a heat recovery unit is used, the difference in heating performance is even greater, rising to −70%. [Copyright &y& Elsevier]

Abstract: Thermally activated building systems (TABS) integrate the building structure as energy storage, and have proofed to be energy efficient and economic viable for the heating and cooling of buildings. Although TABS are increasingly used, in many cases control has remained an issue to be improved. In this paper, a method is outlined allowing for automated control of TABS in intermittent operation with pulse width modulation (PWM). This method represents one part of a TABS control solution with automatic switching between cooling and heating modes for variable comfort criteria which was published before. A first pulse width modulation control solution is derived based on a simple 1st order model of TABS. Then a second, even simpler solution is given that significantly reduces the tuning effort. Finally, the paper outlines a pulse width modulation control procedure and gives two application examples of the PWM control carried out in a laboratory test room. [Copyright &y& Elsevier]

Abstract: Heating Ventilation and Air Conditioning (HVAC) system energy consumption on average accounts for 40% of an industrial sites total energy consumption. Studies have indicated that 20 – 30% energy savings are achievable by recommissioning Air Handling Units (AHUs) in HVAC systems to rectify faulty operation. Studies have also demonstrated that on-going commissioning of building systems for optimum efficiency can yield savings of an average of over 20% of total energy cost. Automated Fault Detection and Diagnosis (AFDD) is a process concerned with automating the detection of faults and their causes in physical systems. AFDD can be used to assist the commissioning process at multiple stages. This paper outlines the development of an AFDD tool for AHUs using expert rules. It outlines the results of the alpha testing phase of the tool on 18 AHUs across four commercial & industrial sites with over €104,000 annual energy savings detected by the AFDD tool. [Copyright &y& Elsevier]

Abstract: This paper studied the annual thermal performance of a photovoltaic wall (PV wall) mounted on a multi-layer façade. Based on some developed unsteady-state heat transfer models for a PV wall and a normal wall, the annual thermal performance of two types of walls was simulated. Compared with a normal wall, the south-facing PV wall could reduce heat gain through the envelope by 51% in summer under Hong Kong weather conditions. The impact of the PV wall on the envelope’s heat gain and heat loss in winter was investigated for the first time, and the results indicated that the PV wall could not only significantly reduce the heat gain through the envelope in daytime, but also reduce the heat loss at nighttime. The heat gain and heat loss through the PV wall in winter were reduced by 69% and 32% respectively compared with a normal wall. Totally, an annual thermal energy consumption reduction of 52.1kWh was achieved by replacing each square meter of a south-facing normal wall by a PV wall, which is equivalent to a saving of 18.6kWh of electric energy for the air conditioning system in a building. The impact of the thickness of an air duct on the thermal performance of the PV wall was also discussed. [Copyright &y& Elsevier]

Abstract: The paper presents a study of solar electricity generation and energy demand for heating and cooling of housing units’ assemblages. Two-story single family housing units, located in northern mid-latitude climate are considered in the study. Parameters studied include geometric shapes of individual units, their density in a neighborhood, and the site layout. The plan shapes of the housing units included in this study are rectangles and several variants of L shape. Site layouts studied are characterized by a straight road, a south-facing or a north-facing semi-circular road. Rectangular units and a site layout with straight road serve as reference for evaluating the effect of shape and site parameters. Results indicate that a significant increase in total electricity generation (up to 33%) can be achieved by the building integrated photovoltaic (BIPV) systems of housing units of certain shape-site configurations, as compared to the reference. The energy load of a building is affected by its orientation and shape. Increased heating demand by L variants (by up to 8%) is more than offset by annual electricity production of their BIPV systems (by up to 35%). Heating and cooling loads depend significantly on unit density in a site; Attached units require up to 30% less cooling and 50% less heating than detached configurations of the same site. Variation of surface orientation, particularly in curved site layouts, enables the spread of peak electricity generation over up to 6h. This effect may be beneficial to grid supply efficiency. Energy balance assessment indicates that some unit shapes generate up to 96% of their total energy use. Neighborhood configurations studied generate between 65% and 85% of their total energy demand. [Copyright &y& Elsevier]

Abstract: A retrofit study was conducted in an unoccupied manufactured house to investigate the impacts of airtightening on ventilation rates and energy consumption. This paper describes the retrofits and the results of the pre- and post-retrofit assessment of building airtightness, ventilation, and energy use. Building envelope and air distribution systems airtightness were measured using fan pressurization. Air change rates were measured continuously using the tracer gas decay technique. Energy consumption associated with heating and cooling was monitored through measurement of gas consumption by the forced-air furnace for heating and electricity use by the air-conditioning system for cooling. The results of the study show that the retrofits reduced building envelope leakage by about 18% and duct leakage by about 80%. The reduction in the house infiltration rates depended on weather conditions and the manner in which the heating and cooling system was controlled, but in general these rates were reduced by about one third. The energy consumption of the house for heating and cooling was reduced by only about 10%, which is relatively small but not totally unexpected given that infiltration only accounts for a portion of the heating and cooling load. [Copyright &y& Elsevier]

Abstract: HVAC (Heating, Ventilation and Air Conditioning) systems used for heating or cooling buildings, consume a considerable amount of energy. To optimize the energy consumption, the behavior of occupants must be changed. This can be achieved by providing information and suggestions to occupants. A first step is developing of a less expensive and non-invasive measurement system and metering of the electricity and heat consumed. Based on collected experimental data, it can identify the parameters of a thermal model of the house. The model obtained will be used to simulate different aspects that can help to reduce the energy consumption. This paper presents a simple solution for thermal modeling of a house which includes experimental identification of the model''s parameters. Such data are used to simulate the thermal behavior of the house and to obtain solutions to reduce energy consumption. In simulation, the control of the thermal system is performed using a model based predictive control algorithm. [Copyright &y& Elsevier]

Abstract: The large thermal time constant of thermally activated building systems (TABS) hampers communication between the system''s production and emission. Therefore, conventional building control strategies, typically using room temperature feedback, are unadapted to control thermal comfort efficiently. In this paper, measurement data and simulation results reveal that unadapted TABS control has a dramatic impact on overall energy performance. Measurements in a TABS building with room temperature feedback show the HVAC system switching between heating and cooling in a very short time frame. A simplified, generic room model is used to simulate, understand and evaluate this behaviour. For room temperature feedback control, only 45% of the cold and 15% of the heat produced actually controls room temperature. The remainder is stored in the TABS and exchanged between the heating and cooling system. Enlarging the heating-to-cooling set point band improves this ratio, while maintaining thermal comfort. On the other hand, night time operation control of the circulation pump, adapted to the TABS thermal time constant, eliminates this ‘unused’ energy completely. In this case, however, even with perfect heat gain forecasts, it is difficult to avoid room temperatures dropping below thermal comfort limits during initial office hours. Hence, a supplementary air-conditioning system seems inevitable. [Copyright &y& Elsevier]

Abstract: Axiomatic design (AD) is a theory that helps to develop new design objects and allows one to evaluate the quality of designs. The aim of this paper is to apply this theory to the design of heat ventilation and air-conditioning (HVAC) systems and to come to conclusions about the design quality of some specific applications. The focus is the comfort and energy consumption in commercial buildings in South European climates. The discussion contains a brief description of variable air volume (VAV) systems and dedicated outdoor air systems (DOAS) with terminal units, such as fan-coils, induction units and chilled ceilings. Occasionally, the DOAS design should include over-cooled outdoor air in order to ensure an extra cooling means. According to the AD''s first axiom, ideal systems are independent or decoupled. Our conclusion is that VAV and DOAS with induction units are coupled designs, and on the other end, DOAS with fan-coils or chilled ceilings are decoupled designs. In addition, over-cooling outdoor air (OA) flow couples the OA flow with the indoor heat removable needs. [Copyright &y& Elsevier]