Search

This paper utilized the hydrothermal method and freeze-drying technology to prepare the macroscopic aerogel structure and powder structure of MOF-808/RGO. Through comparative analysis of aspects such as photocatalytic CO 2 reduction performance, electron transfer efficiency, macroscopic structure, and microstructure, it has been discovered that aerogel structure can provide favorable conditions for mass transfer of CO 2 and water molecules, and light propagation. The introduction of RGO successfully captures electrons and the reduction reaction occurs on the surface of the material. [Display omitted] • Macroscopic aerogel and powder structures of the MOF-808/RGO composite photocatalysts were fabricated separately and used for comparison. • The photocatalytic performance of the MOF-808/RGO macroscopic aerogels in reducing CO 2 to CO was approximately 16 times that of MOF-808 and 12 times that of RGO. • The aerogel structure provides an abundance of pore structures within the material. • The presence of the aerogel structure successfully enhanced the photothermal and photoelectric conversion efficiencies of the composite photocatalysts. Three-dimensional (3D) macroscopic aerogels have emerged as a critical component in the realm of photocatalysis. Maximizing the integration of materials can result in enhanced efficiency and selectivity in photocatalytic processes. In this investigation, we fabricated MOF-808/reduced graphene oxide (RGO) 3D macroscopic aerogel composite materials employing the techniques of hydrothermal synthesis and freeze-drying. The results revealed that the macroscopic aerogel material exhibited the highest performance in CO 2 reduction to CO, particularly when the concentration of RGO was maintained at 5 mg mL−1. In addition, we synthesized powder materials of MR-5 composite photocatalysts and conducted a comparative analysis in terms of photocatalytic CO 2 reduction performance and electron transfer efficiency. The results show that the macroscopic aerogel material boasts a high specific surface area, an abundant internal pore structure, and increased active sites. These attributes collectively enhance light energy utilization, and electron transfer rates, thereby, improving photothermal and photoelectric conversion efficiencies. Furthermore, we conducted in-situ FT-IR measurements and found that the M/R-5 aerogel exhibited the best CO 2 adsorption capacity under a CO 2 flow rate of 10 mL min−1. The density functional theory results demonstrate the correlation between the formation pathway of the product and the charge transfer pathway. This study provides useful ideas for realizing photocatalytic CO 2 reduction of macroscopic aerogel materials in gas–solid reaction mode. [ABSTRACT FROM AUTHOR]

Designing S-scheme heterojunctions is an effective method to improve the charge localization on the surface of photocatalysts. Their effective charge transport routes can be enhanced with the help of interfacial noble metal nanoparticles. Herein, an Ag/CuO@ZnIn 2 S 4 plasma S-scheme heterojunction with heterogeneous interfacial covalent bonds was successfully designed. The 15% Ag/CuO@ZnIn 2 S 4 has promising photocatalytic performance and stability with the highest CO and CH 4 yields of 6.9 and 54.4 µmol g−1 h−1 and CH 4 selectivity of 92.8%. It is evidenced that the photogenerated charge can be efficiently separated and transported due to the influence of both the S-scheme electron migration mode and the Cu-S covalent bond. The process is further accelerated by using precious metals as cocatalysts, which can then selectively convert CO 2 into CH 4. This research is expected to provide helpful information for engineering S-scheme heterojunction photocatalysts and investigating their charge transfer kinetics. [Display omitted] • Design of a S-scheme heterojunction to promote the separation of carriers. • Built the Cu-S bonds to accelerate the transfer of charges. • Utilizing the LSPR effect to generate hot electrons and enhance light absorption. • The Ag/CuO@ZnIn 2 S 4 photocatalysts can selectively reduce CO 2 to CH 4. [ABSTRACT FROM AUTHOR]

The interfacial regulation strategy between semiconductors can effectively promote the separation efficiency of photogenerated carriers and enhance photocatalytic activity under the synergistic effect. Herein, AgInS 2 QDs-MoS 2 /GO (AIS-MS/GO) composites were prepared by interfacial coupling of AgInS 2 QDs (AIS), hierarchical MoS 2 and ultrathin GO. Ultrathin GO successfully solved the agglomeration problem of AIS and hierarchical MoS 2. Moreover, the photogenerated carriers were effectively separated and transferred under the synergistic effect of the AIS-MS heterojunction and ultrathin GO, thus promoting tetracycline (TC) degradation and CO 2 reduction performance. The degradation rate of tetracycline (TC) reached 96.5 %, and the yields of CO and CH 4 in the CO 2 reduction products reached 52.6 and 28.5 μmol g–1, respectively, when using the optimized photocatalyst. In-situ FTIR analysis indicated that TC is gradually degraded by small molecules on the composite surface, and has excellent dissociation ability of water molecules during the CO 2 reduction process. This work provides a new vision for the rational design of heterojunction-based photocatalysts using the interfacial regulation strategy for enhancing interfacial charge separation and photocatalytic performance. [Display omitted] • AIS-MS/GO composites were prepared via the interfacial regulation strategy. • The photogenerated carriers were effectively separated and transferred under synergistic and interfacial effects. • The aggregation problem of AIS and hierarchical MoS 2 was effectively solved. • AIS-MS/GO composites achieve a 96.5 % TC degradation rate and 35.1 % selectivity for CH 4. [ABSTRACT FROM AUTHOR]

Energy band location and charge separation mechanism of SnS 2 /Au/g-C 3 N 4 system during photoreduction under sunlight irradiation. • The catalyst is prepared by facile thermal treatment and chemical deposition method. • The SnS 2 /Au/g-C 3 N 4 composites show a superior optical adsorption under UV–vis light. • The Au nanoparticle and the Z-type scheme jointly improve the separation of carrier. • The SnS 2 /3ml-Au/g-C 3 N 4 displays the best photoreduction activity and durability. The use of semiconductor photocatalytic reduction technology has higher efficiency and lower energy consumption for CO 2 reduction, but its existence of some mismatched energy band positions and relatively slow charge-hole separation greatly limits its practical application. In this paper, a SnS 2 /Au/g-C 3 N 4 embedded structure model with carbon and nitrogen hybridization is proposed to gain an in-depth understanding of the role of hybridization and precious metal modification in photocatalysis. Carriers were investigated from the perspective of kinetics through photocurrent, LSV curve, and FL spectroscopy. After modification of Au nanoparticles, the photo-excited electrons showed a slower decay process, indicating that the separation of carriers was enhanced, which was further confirmed by impedance and PL spectroscopy. SEM, AFM and TEM analysis confirmed that the 2D face-to-face SnS 2 /Au/g-C 3 N 4 embedded structure was successfully prepared and the Au nanoparticles were evenly distributed. Au nanoparticles not only act as a bridge for electron transport in 2D semiconductor materials to accelerate electron transport, but generate more excited electrons by themselves under the radiation of sunlight, which effectively improves the separation efficiency of electron-hole pairs and enhances the photocatalyst activity. DFT calculations show that the Z-type mechanism and the intercalated energy level of the SnS 2 /Au/g-C 3 N 4 embedded structure expand the light absorption and improve the carrier separation efficiency. As expected, the photocatalyst activity with CO and CH 4 the evolution rate of up 93.81 µmol·g−1·h−1 and 74.98 µmol·g−1·h−1 under visible light irradiation, respectively, while the photocatalytic activity is negligible loss after 30 h photoreduction. This work reveals the role of embedded structure and precious metal modification in the separation and transmission of electron-hole, opening up new perspective for achieving high-efficiency solar CO 2 reduction performance. [ABSTRACT FROM AUTHOR]