Search

The energy exchange between series and shunt converters is the basis for the powerful functioning of the unified distributed power flow controller, which can be realized through the 3rd harmonic current. In this paper, based on the established 3rd harmonic equivalent network of unified distributed power flow controller power system, the influence of the additional loss caused by the 3rd harmonic current on the line transmission capacity is analysed. The mathematical relationship between the neutral point voltage of the transformer and the 3rd harmonic current is constructed, and it is simplified according to the different 3rd harmonic currents. By analysing the power relationship of the 3rd harmonic equivalent network, it is found that there is a contradiction between improving the 3rd harmonic output efficiency of the shunt single‐phase converter and reducing the neutral point insulation voltage of the transformer. The constraint conditions of the 3rd harmonic current are simulated by the advanced digital power system simulator. Finally, the method of obtaining the economical and safe 3rd harmonic current value range is summarized, which provides a theoretical basis and reference for the device parameter design. [ABSTRACT FROM AUTHOR]

This paper analyses the formation mechanism of the transmission distortion of electronic voltage transformer, and points out that the integrator will magnify the transient transfer error and superimpose the dynamic additional component on the output signal, which may cause the transfer distortion of voltage signal in serious cases. To restrict the electronic transformer transient variable error effect on distance relay, a distance relay method using instantaneous value after equal transfer processes is proposed. It directly uses output differential signals of the capacitor voltage divider and Rogowski coil. The capacitor voltage divider and Rogowski coil are decomposed into several typical variable link in series. The virtual digital transfer link, which is constructed by the digital filter, is used to compensate for the difference parts of the transfer link, so that the voltage and current signals pass through the same transfer link. It can mitigate the influence of voltage and current signal transfer difference on the calculation accuracy of distance relay. The simulation results show that the proposed distance relay method has fast operation speed and is less affected by abnormal voltage and current signal transfer, and its performance is better than existing distance relay methods. [ABSTRACT FROM AUTHOR]

Power electronic transformer (PET) should have a satisfying low‐voltage ride‐through (LVRT) ability to cope with different kinds and severities of voltage sags. To solve the LVRT issue, this paper proposes to coordinate mode switching control (MSC) and superconducting magnetic energy storage (SMES), and it is to realize the targets of promoting voltage recovery, keeping DC‐link stabilization, and alleviating current inrush. First, the theoretical modeling of a PET incorporating with a SMES unit is implemented, and the PET's fault transient characterizes as well as the SMES's potential supportability is analyzed. Then, the coordination philosophy of the MSC and the SMES is presented. For that the voltage sag reaches a certain threshold, the MSC is enabled to remove the PET's normal control, and the SMES collaboratively operates to lower the DC‐link overvoltage, while avoiding the PET damage. In the process of the coordination control handling the voltage transients, a proper reactive current injection is carried out at the PET's output stage to assist the voltage recovery, and the PET can possess a better LVRT margin. Using MATLAB, a 3 MW PET with an 8 H/1.2 MJ SMES unit is modeled, and different voltage sag scenarios and utilization ways of the MSC and the SMES are simulated. The comparative analysis results show that the proposed approach realizes a satisfying LVRT for the PET. [ABSTRACT FROM AUTHOR]

The general method for identifying the partial discharge type in a power transformer is based on their fingerprints in the form of phase-resolved discharge patterns. In the case of multiple defects, traditional clustering methods can be applied for separation of active sources. However, such an approach is impractical for online real-time monitoring due to the very large data size. In this paper a new method using stream clustering is introduced. The method separates the active sources by processing the signal once it is captured, then only a synopsis of the discharge data is stored. Two stream clustering algorithms: Density Grids and DenStream are employed. Through measurements obtained from laboratory experimental setups (corona, surface discharge, transformer defect model) performance of the proposed algorithms are evaluated. It is shown that stream clustering method is able to separate the constituent components involved in the stream of a multi-source discharge signal without the need to store a large amount of information. The performance of the Density Grids method depends on a limited number of features that it can accommodate. In comparison, the DenStream method can capture more features which enable better separation of active sources at the expense of longer processing time. [ABSTRACT FROM AUTHOR]