Search

An inorganic-organic fluorinated titania-silica (fTiO 2 -SiO 2 )/polyvinylidene fluoride (PVDF) composite membrane was fabricated, via facile in-situ vapor-induced hydrolyzation method followed by hydrophobic modification. This low mass-transfer-resistance membrane, composing of a mesoporous layer deposited onto macroporous substrate, was designed for biogas upgrading in gas-liquid membrane contactor (GLMC) application. The surface hydroxylation was introduced to facilitate the bridging of TiO 2 -SiO 2 nanoparticles and PVDF substrate, which resulted in a more coherent deposition of the fTiO 2 -SiO 2 layer onto the substrate. The surface microstructure was fine-tuned by controlling the amount of doped Si precursor, forming an integrated mesoporous fTiO 2 -SiO 2 layer. The resultant fTiO 2 -SiO 2 /PVDF composite hollow fiber membrane exhibited a tighter pore size of ~25 nm and a desired water contact angle of ~124°, which effectively prevented membrane wetting. The CO 2 absorption fluxes of 8.0 and 5.6 × 10 −3 mol m −2 s −1 were achieved due to the lower mass transfer resistance, by using 1 M of monoethanolamine (MEA) and sodium taurinate as absorbents with a liquid velocity of 0.25 m s −1 , respectively. The long-term stability test showed a good integrity between the fTiO 2 -SiO 2 layer and the PVDF substrate after 31-days of GLMC operation. The main benefit is the robust fluorinated inorganic layer which exhibited strong chemical resistance and high hydrophobicity, thus preventing membrane damage and pore wetting. Overall, this work provides an insight into the preparation of high–performance inorganic/organic composite hollow fiber membranes for carbon dioxide (CO 2 ) removal in GLMC application. [ABSTRACT FROM AUTHOR]

Due to its toxicity to ecosystem, phenol removal from industrial wastewater before discharge is a priority concern. Extractive membrane bioreactor (EMBR), a novel wastewater treatment process combining aqueous–aqueous extractive membrane process and biodegradation, has shown potential in treating phenol in wastewater. In this paper, composite hollow fiber membranes with different levels of poly(dimethylsiloxane) (PDMS) intrusion were prepared by coating a layer of PDMS on a Polyetherimide (PEI) hollow fiber substrate. Their applicability to EMBR for phenol removal was studied. The prepared membranes were characterized by microscopy and gas permeation test, and their performances were evaluated in aqueous–aqueous extractive membrane processes and EMBR process. The overall mass transfer coefficient for phenol, or k 0 , was found to be significantly affected by the level of PDMS intrusion in the composite membranes. This is because the penetration of PDMS into the porous substrate results in a denser membrane structure, which consequently increases the membrane resistance. A slight penetration of PDMS into the substrate was found to be necessary for the composite membranes to achieve high k 0 while maintaining low inorganic flux across the membranes. Wilson-plot analysis suggests that membrane resistance dominated over liquid boundary layer resistances. After more than 250 h of EMBR operation, significant biofilm growth was observed on the composite membranes and the k 0 was dropped but stabilized at around 7.5×10 −7 m/s. This k 0 was 7.5 times higher than commercial PDMS tubular membranes (without biofilm development) reported in previous studies, confirming the superiority of thin film composite membranes prepared in this work. It was also found that process optimization to control biofilm thickness is important in order to enhance phenol removal rate in EMBR. [ABSTRACT FROM AUTHOR]

Novel composite forward osmosis (FO) hollow fiber membranes with two selective skin layers were developed in the present work. The polyethersulfone (PES) hollow fiber substrate was firstly fabricated by a phase inversion method. The RO-like polyamide skin layer was then prepared on the inner surface of the hollow fiber substrate via interfacial polymerization (IP), while the NF-like outer skin layer was prepared via polyelectrolyte layer-by-layer (LBL) assembly. Three double-skinned membranes with negative (DS#1.5), positive (DS#2.0) and minimal (DS#2.5) outer surface charges under neutral pH environment were evaluated for their capabilities against organic fouling in the FO process. The newly developed double-skinned membranes possess water permeability greater than 2 l/m 2 h bar and NaCl rejection higher than 95% under 2 bar pressure, and have superior water flux and less salt leakage than the commercial HTI FO membranes as well as all the reported double-skinned FO membranes with RO-like selective layers. Most importantly, the double-skinned DS#2.5 hollow fiber membrane exhibits exciting organic fouling resistance because of its highly hydrophilic NF-like secondary layer with minimal surface charge and tightened surface structure to mitigate possible substrate pore clogging and fouling layer formation. A stable water flux of around 25 l/m 2 h was attained for DS#2.5 membrane using <0.5 M NaCl as the draw solution and a water containing 200 ppm dextran (DEX) or Aldrich humic acid (AHA), or lysozyme (LYS) and 10 mM NaCl as the model feed in the active layer against the draw solution (AL-DS) configuration, suggesting its great potential for practical FO applications. [ABSTRACT FROM AUTHOR]