Search

The focus of whey processing has been changed from waste treatment to the production of valuable products owing to the advancement of membrane technology. Producing high quality whey products at low energy consumption entails novel techniques for whey concentration. This study proposes forward osmosis (FO) as a potential approach to concentrate whey protein solutions, which is superior to the concentration via reverse osmosis (RO), mainly owing to the low hydraulic pressure during FO process. In particular, this work validated the feasibility of FO-based whey concentration using high-performance hollow fiber membranes that were fabricated in-house. The investigation focused on the effects of various operating conditions on the concentration performance. The experimental results reveal that optimal concentration efficiency would be achieved by appropriately choosing the cross-flow velocity, draw solution concentration and the maximum attainable concentration of whey protein solution. Especially, the flux decline behaviour as a function of the whey protein concentration in the feed solution indicated rapid formation of a polarized or gel foulant layer at the membrane surface. The proposed mechanism was supported by the investigation of physical cleaning with water, showing that the post-process cleaning after the concentration cycle was able to recover the membrane performance, whereas the intermediate cleaning during one concentration cycle had little impact on the concentration efficiency enhancement. This study has practical significance for the application of FO in the concentration of dairy streams and other liquid foods. [ABSTRACT FROM AUTHOR]

The layer-by-layer (LBL) polyelectrolyte deposited membranes have drawn increasing attention in various applications due to the ease of selective layer formation and their stability and versatility. In this study, the LBL deposition was performed at the inner surface of the polyethersulfone (PES) hollow fiber substrate to form composite nanofiltration (NF) membrane. The semi-dynamic deposition procedure was adopted with the aid of syringes. The newly developed inner deposited (id-LBL) membranes were then tested in NF and forward osmosis (FO) applications and the performance were compared with outer surface deposition as well as some literature data. The id-LBL membranes could not only withstand higher operating pressure but also possess superior hardness rejection especially in high concentration mixed salt solutions (more than 95% rejection to Mg 2+ and Ca 2+ in a 5000 ppm total dissolved salt (TDS) mixture under 4.8 bar). As for the FO process, with only two layer deposition, the id-LBL membranes also demonstrated significant performance improvement with increased water flux (up to 70 L/m 2 h using 0.5 M MgCl 2 as draw solution in active layer facing draw solution configuration) and reduced salt leakage (around 0.5 g/m 2 h using 1 M MgCl 2 draw solution in active layer facing feed water configuration). This study suggests that for hollow fiber substrate, the inner surface is more suitable for the formation of the selective layer via LBL deposition than the outer surface. [ABSTRACT FROM AUTHOR]

Pressure retarded osmosis (PRO) is a promising energy harvesting technique. However, when polymeric hollow fiber membrane is used for the PRO process, the mechanical strength of the membrane is a big concern. As hollow fiber membrane is self-supported and due to its polymeric nature, it may gradually deform over time under high pressure loading, or membrane “creeping” will occur. Current work is the first attempt to analyze the membrane creeping phenomenon of a novel thin film composite (TFC) hollow fiber. The membrane creeping was evaluated via nanoindentation by using atomic force microscope (AFM). A non-stop 200-hour PRO test and integrity check, which have not been reported previously, were carried out to investigate the membrane performance under various operating pressures. The results show that the membrane is able to produce a stable power density output of 19.2 W/m 2 at 15.0 bar, using 1.0 M NaCl as the draw solution and DI water as the feed water. Membrane creeping was observed when the applied pressure exceeded the safe operation limit (or the flux turning point, where the membrane flux started to increase with increasing applied pressure in the PRO mode), which caused an irreversible damage to the membranes. This study identified safe and optimum operation conditions of the laboratory-made PRO hollow fiber membrane to achieve the most favorable PRO performance. It provides guidance for practical applications of polymeric hollow fiber membranes in PRO process. [ABSTRACT FROM AUTHOR]