Search

The characteristics, breakdown probability, and statistical distribution of breakdown time delay under different du/dt in hundreds of nanoseconds pulse for millimeter gaps have been investigated by employing the statistical experimental method in this paper. The experimental results indicate that both the breakdown time delay and jitter are essentially decreased as the slope of the pulse voltage- du/dt is increased for 1-, 2-, and 4-mm gaps; in particular, increasing the value of du/dt is useful to obtain the smaller relative deviation of breakdown time delay under the same breakdown electric field. The breakdown probabilities for different gaps have been analyzed and a method of utilizing the Gaussian distribution function has been proposed which can be used for evaluating the statistical distribution of breakdown time delay. When the experimental condition is 100% breakdown probability, the breakdown time delay follows a Gaussian distribution. However, it is unsuitable for the fitting of breakdown time delay utilizing a Gaussian function for 2- and 4-mm gaps from the cumulative probability distributions of breakdown time delay because of the lower du/dt values and breakdown probabilities. [ABSTRACT FROM AUTHOR]

A polypropylene (PP) film is usually employed as the main insulation of the peaking capacitor, which is important in an electromagnetic pulse simulator to generate high-amplitude nanosecond pulse. The flashover voltage of PP films under nanosecond pulse limits the highest working voltage of a peaking capacitor. Surface fluorination was employed to increase the flashover voltage of PP. The flashover voltages of PP samples with different fluorination times (0, 4, and 6 h) were tested in an oven with nanosecond pulse voltage. The results showed that the flashover voltage of the PP film with 6-h surface fluorination was increased about 15% than the untreated film in the air. To clarify the influential mechanism, the physicochemical properties of PP film samples were tested and characterized. The results of thermally stimulated depolarization current (TSDC) showed that the trap density of the PP film increased obviously after fluorination treatment. With the increase in treatment time, the trap depth and density were increased obviously. The surface conductivity of PP films slightly decreased with the increase in fluorination time. The mechanism of surface fluorination on the influence of the flashover performance of the PP film under nanosecond pulse is discussed. It is concluded that surface fluorination significantly increases the carbon–fluorine (C–F) bond of the PP film, resulting in the increase in the depth and density of the surface trap, and then, a large amount of homocharges trapped in the surface trap reduces the electric field near the electrode. [ABSTRACT FROM AUTHOR]

Megavolt-class pulsed gas switches play an important role in large pulsers as transfer switches. This article analyzes the breakdown process and characteristics of a megavolt self-triggered preionized switch under 100-ns pulses based on the optical diagnosis. It is discovered that the triggering spark illumination targeting the main cathode or anode can separately preionize the main gap. The discharge channel is likely to first form between trigger electrodes and the main anode. Based on the above deduction, the streamer velocity is calculated to be $0.54 \times 10^{6}$ – $2.34 \times 10^{6}$ m/s, proportional to the electric field. Also, parameters of the empirical formula for calculating the gas heating time are amended. Influence mechanisms of the switch jitter are also studied. Under pulsed preionization mode, the trigger gap breaks down when the main gap electric field is high enough, and the switch jitter is mainly determined by the self-triggering jitter. Nonetheless, the self-triggering jitter can be partly offset during the breakdown process if the changing rate of mean reduced electric field $d(E/p)$ / dt at the self-triggering time is higher than 1.0 $1.0\left(\mathrm{kV} \cdot \mathrm{ns}^{-1} \cdot \mathrm{cm}^{-1} \cdot \mathrm{MPa}^{-1}\right)$. Under sustaining preionization mode, the trigger gap breaks down prematurely, and the continuous arcing driven by switch leak current preionizes the main gap. Therefore, the influence of the self-triggering jitter on the switch jitter can be eliminated. [ABSTRACT FROM AUTHOR]

Due to its low-loss and high dielectric strength, polypropylene is widely used as electrical insulation material in pulse capacitors. In order to study its breakdown characteristics for nanosecond voltage pulses, an experimental setup was designed to generate voltage pulses with a 10%–90% rise time of 38 ns and a full width at half maximum of about 90 ns. Tests of the three polypropylene films with thicknesses of 12, 15, and $18~\mu \text{m}$ were performed. In addition, hundreds of nanoseconds pulse and dc voltage were also applied for comparison. The experimental results reveal that most of the breakdown occurs during the front edge of the pulse for tens of nanoseconds pulse, and the breakdown strengths of the three kinds of polypropylene films are almost identical for different applied voltages, which show a weak correlation between the thickness of the dielectric and the breakdown field. The expected breakdown strength of tens of nanoseconds pulse defined in this paper is not significantly higher than the mean value of the hundreds of nanoseconds pulse and the dc condition, suggesting that the breakdown of a thin polypropylene film is mainly determined by the electrical field but not the voltage-time cumulative effect. All these observations strengthen the conclusion that the breakdown of a thin polypropylene film is an intrinsic phenomenon. [ABSTRACT FROM AUTHOR]