Search

This paper describes a method for the comparison of the cooling capability of over-the-counter devices for skin tags removal. The comparison is performed by measuring the heat flux produced by the gas identified assessing the temperature difference across an element with a known thermal resistance; the temperature reached at the interface between the device and the heat-flux meter is also analyzed, although it is different from that of the skin during the treatment. The measurement accuracy has been experimentally evaluated and, with a confidence interval of 95%, is better than 6% for heat-flux measurements and lower than 0.3 °C for temperature measurements. The instrument allowed comparing the thermal efficiency of 19 dimethyl ether and propane devices of different types (dispenser, spray, and foam). Results are by far more reliable than those obtained with tests performed on subjects, where the intrinsic skin thermal properties variability prevents from assessing differences smaller than 30%. [ABSTRACT FROM PUBLISHER]

The skin–contact thermal resistance is a parameter that allows evaluating, in steady condition, the heat flow at the interface between the skin and a rigid surface at a known temperature. At the current state of the art, it is evaluated with empirical equations and is known to be dependent on the contact pressure, on the surface characteristics, and on the skin conductivity. The need to measure skin and contact thermal resistance with low uncertainty led to the realization of the device described in this paper. The instrument—based on the principle of the thermoflowmeter—has been designed with the goal of minimizing the measurement uncertainty with contact temperatures ranging between 12 ^\circ\C and 27 ^\circ\C and contact areas from 50 to 314 \mm^2. The device allows varying and controlling the interface pressure and temperature that, according to existing literature studies, are likely to influence the skin thermal properties. The different temperatures needed for the evaluation of the thermal resistance are measured with individually calibrated thermocouples. The metrological characterization of the flowmeter was performed under vacuum, and the effect of convective heat exchanges in normal operation was modeled and compensated. Measurement repeatability and reproducibility were assessed by measuring the thermal resistance of plastic materials in operational conditions. Preliminary tests showed that the skin–contact thermal resistances measured in different conditions are compatible with the theoretically evaluated ones, with improvement in uncertainty due to direct measurement. [ABSTRACT FROM PUBLISHER]

Plantar pressure measurements provide useful information to diagnose a diverse range of foot disorders; unfortunately, the commercially available measurement systems are undesirably sensitive to several disturbances, but this aspect is mostly neglected in the literature. This paper describes the results of an experimental campaign aiming at the identification of pressure measuring system metrological performances, at system modeling, and at the implementation of correction procedures. The sensor model was implemented using the results of static and dynamic tests performed on a pedar-X plantar pressure measurement system. The static calibration was performed by analyzing the effect of temperature, single sensor coverage area, local curvature, tangential forces, long-term stability (creep), and sensor crosstalk on the system performances. The dynamic calibration was performed on an electrodynamic shaker, identifying the single sensor frequency response function and the hysteresis under different average loads. The dynamic sensor model is based on the Kelvin–Voigt model, which is representative of the viscoelastic behavior of the material. The model allowed us to compensate both the creep (i.e., the behavior under static loads) and the nonunitary frequency response function. A deconvolution-based algorithm has been proposed to compensate the sensor crosstalk effects, although its implementation requires additional investigations. Experimental results of bobbing and gait tests showed that, with the adoption of the proposed compensation algorithms, the force and center of pressure errors could be reduced by more than 50\% of their initial values. [ABSTRACT FROM PUBLISHER]

This paper describes a method that allows accuracy and bandwidth enhancements in 3-D sound intensity measurements. Commercial 3-D probes are usually set up with three mutually perpendicular 1-D p-p probes and, thus, arranged with six microphones; although sound intensity can be calculated with 15 independent pairs of transducers, only the three "primary" pairs that are aligned with the coordinate system axes. The other 12 "secondary" pairs consist of mutually perpendicular microphones, which are placed at a distance that is √2 times shorter than the primary one. The main idea of the proposed method is to average the intensity that is measured on primary and secondary pairs. This leads to a larger bandwidth, thanks to the shorter separating distance between secondary pairs. The intrinsic p-p method high- frequency sensitivity loss is partially recovered, starting from the theoretical plane wave expression. Measurements of different axes are weighted with coefficients that are computed by optimizing the measurement uncertainty. Errors that are due to the metrological characteristics of the transducers and the effects of environmental conditions are compensated. Experimental results showed that a p-p probe arranged with half-inch microphones that are placed at a distance of 50 mm allows reliable measurements up to 2.5 kHz, whereas a commercial probe bandwidth with the same configuration is usually 1250 Hz. [ABSTRACT FROM AUTHOR]