Search

The combination of superelastic shape memory alloy fibers and ECC materials can form a new SMA fiber reinforced ECC composite material (SMAF-ECC) with good self-centering performance. In order to study the self-centering performance of the new composite material, 6 groups of pre-notch beam specimens were made for three-point bending cyclic loading tests, and the failure phenomenon, hysteresis curve, self-centering effect and influencing factors of the specimens were analyzed. The research results show that when the SMA fibers are effectively anchored in the ECC matrix, the SMA fibers can exert the superelastic properties to provide the ECC beams with recoverying force, and realize the crack self-closure and deflection self-recovery function for the beams, with the minimum residual crack width and deflection is only 0.9 mm and 1.3 mm respectively. Increasing fiber content can cause a small increase in the self-centering ability of the beams. However, only when the fiber diameter is appropriate, better self-centering effect can be achieved, but the difference caused by fiber diameter in the test was only 5%. SMA Fiber end forms have significant influence on self-centering performance. The knotted end beam can get a more than 70% self-centering ratio, while the straight end beams and bended end beams have no self-centering ability. The research results provide important reference for the research and application of this new self-centering materials and their structures. [ABSTRACT FROM AUTHOR]

The electrical and optical properties of (001)‐ and (110)‐oriented 0.73 Pb(Mg1/3Nb2/3)O3‐0.27PbTiO3 single crystals are systematically investigated at various temperatures, both of which present a series of ferroelectric phase transition processes. Dielectric performance measurements reveal that the ferroelectric phase transition occurs over a temperature range, rather than at one temperature point. By testing the ferroelectric hysteresis P–E curves as well as bipolar and unipolar electric field‐induced strain S–E curves, the values of remnant polarization, coercive field, maximum strain, and converse piezoelectric constant d33* change considerably near the phase transition temperatures. Simultaneously, the 0.73PMN‐0.27PT single crystals with (001)‐ and (110)‐orientations under a low electric field show ultrahigh d33* values of 3540 and 2817 pm/V, respectively, which can be attributed to the electric field‐induced monoclinic and orthorhombic phases, respectively. The series of ferroelectric phase transitions upon heating, that is, from rhombohedral ferroelectric to monoclinic/orthorhombic, followed by from monoclinic/orthorhombic to tetragonal, and finally from tetragonal to cubic paraelectric, are further investigated via polarized light microscopy and Raman spectroscopy. The 0.73PMN‐0.27PT single crystals present a series of ferroelectric phase transition processes, which is confirmed by dielectric performance measurement, polarized light microscopy and Raman spectra contour plot. The electric field induced monoclinic and orthorhombic phase contribute to the ultra‐high d33- in the (001)‐ and (110)‐orientations crystals. [ABSTRACT FROM AUTHOR]

The temperature stability and temperature stability range of barium titanate-based pulse energy-storage ceramics were modified by Bi 2 O 3 tailoring in (Ba 0.98- x Li 0.02 Bi x) (Mg 0·04 Ti 0.96)O 3 (x = 0, 0.025, 0.05, 0.075, 0.1) and (Ba 1.03-1.5 x Li 0.02 Bi x) (Mg 0·04 Ti 0.96)O 3 (x = 0.125, 0.15, 0.2, 0.25) ceramics. Excellent pulse energy-storage performances of ceramic films are achieved via the new dual priority strategy of establishing cationic vacancies and forming a liquid phase. The dielectric constant plateau appears due to the cubic phase and space charges. Outstanding temperature stability, frequency stability and antifatigue performance are obtained in the ceramics, and their variations are all less than 15%. The comprehensive energy-storage properties with dual priority parameters of energy-storage density and efficiency of 3.13 J/cm3 and 91.71%, accompanied by an excellent pulse discharge energy density of 2.48 J/cm3, current density of 1313.23 A/cm2 and power density of 195.26 MW/cm3 are gained at x = 0.1. The perfect pulse energy-storage performances as well as ultrahigh stability are correlated with synergistic effects of multiphase coexistence, cubic phase, liquid-phase sintering, grain size, ceramic resistance, space charges and polar nanoregions. The comprehensive parameters indicate that the (Ba 0·88 Li 0·02 Bi 0.1) (Mg 0·04 Ti 0.96)O 3 ceramics have potential application in high precision fields. [ABSTRACT FROM AUTHOR]

With the popularity of electric vehicles, the ever-increasing demand for high-capacity batteries highlights the need for monitoring the health status of batteries. In this article, we proposed a magnetic imaging technique (MIT) to investigate the health status of power batteries nondestructively. This technique is based on a magnetic sensor array, which consists of a 16-channel high-performance magnetoelectric sensor, and the noise equivalent magnetic induction (NEB) of each channel reaches 3–5 pT/Hz1/2@10 Hz. The distribution of the magnetic field is imaged by scanning the magnetic field variation of different positions on the surface. Therefore, the areas of magnetic anomalies are identified by distinguishing different magnetic field abnormal results. and it may be possible to classify the battery failure, so as to put forward suggestions on the use of the battery. This magnetic imaging method expands the application field of this high-performance magnetoelectric sensor and contributes to the battery's safety monitoring. Meanwhile, it may also act as an important role in other nondestructive testing fields. [ABSTRACT FROM AUTHOR]