Search

To enhance the ecological properties of polyvinyl chloride (PVC) products, the fabrication of PVC-based composites using biofillers with acceptable performance characteristics could be considered. In this work, plant-filled PVC-based composite materials were fabricated and their optical, structural, thermal, and mechanical properties, depending on the nature of the filler, were studied. Spruce flour, birch flour, and rice husk were used as fillers. Optical measurements showed the selected technological parameters, allowing films with a uniform distribution of dispersed plant filler in the polymer matrix to be obtained. Using the plant fillers in PVC films leads to a reduction in strength characteristics; for instance, the tensile strength changed from 18.0 MPa (for pure PVC film) to ~7 MPa (for composites with 20 wt.% of fillers), and to ~5–6.2 MPa (for composites with 40 wt.% of fillers). Thermal investigations showed that the samples with plant fillers could be used at low temperatures without changing their operating characteristics. Thus, plant-filled PVC-based composite materials have a wide operating temperature range, from—65 °C to 150 °C. TGA analysis has demonstrated that the rice husk affected the thermal stability of the composites by increasing their thermal decomposition resistance. The ability to absorb water was observed during the investigation of water absorption of the samples. And the highest degree of water absorption (up to 160 mg/g) was detected for the sample with 40 wt.% of rice husk. In general, plant-filled polymer composites based on PVC can be used on an equal basis with unfilled PVC plastic compounds for some applications such as in construction (for example, for design tasks). [ABSTRACT FROM AUTHOR]

In this work, the overall activation energy of the combustion of lean hydrogen–methane–air mixtures (equivalence ratio φ = 0.7−1.0 and hydrogen fraction in methane α = 0 , 2, 4) is experimentally determined using thin-filament pyrometry of flames stabilised on a flat porous burner under normal conditions ( p = 1 bar, T = 20 °C). The experimental data are compared with numerical calculations within the detailed reaction mechanism GRI3.0 and both approaches confirm the linear correlation between mass flow rate and inverse flame temperature predicted in the theory. An analysis of the numerical and experimental data shows that, in the limit of lean hydrogen–methane–air mixtures, the activation energy approaches a constant value, which is not sensitive to the addition of hydrogen to methane. The mass flow rate for a freely propagating flame and, thus, the laminar burning velocity, are measured for mixtures with different hydrogen contents. This mass flow rate, scaled over the characteristic temperature dependence of the laminar burning velocity for a one-step reaction mechanism, is found and it can also be used in order to estimate the parameters of the overall reaction mechanisms. Such reaction mechanisms will find implementation in the numerical simulation of practical combustion devices with complex flows and geometries. [ABSTRACT FROM AUTHOR]

Edible films based on biopolymers are used to protect food from adverse environmental factors. However, their ample use may be hindered by some challenges to their mechanical and antimicrobial properties. Despite this, in most cases, increasing their mechanical properties and antibacterial activity remains a relevant challenge. To solve this problem, a possible option is to fill the biopolymer matrix of films with a functional filler that combines high reinforcing and antibacterial properties. In this work, biocomposite films based on a mixture of chitosan and cassava starch were filled with a hybrid filler in the form of bentonite clay particles loaded with ginger essential oil (GEO) in their structure with varied concentrations. For this purpose, GEO components were intercalated into bentonite clay interlayer space using a mechanical capture approach without using surface-active and toxic agents. The structure and loading efficiency of the essential oil in the obtained hybrid filler were analyzed by lyophilization and laser analysis of dispersions, ATR-FTIR spectroscopy, thermogravimetry, and X-ray diffraction analysis. The filled biocomposite films were analyzed using ATR-FTIR spectroscopy, optical and scanning electron spectroscopy, energy dispersive spectroscopy, mechanical analysis under tension, and the disk diffusion method for antibacterial activity. The results demonstrated that the tensile strength, Young's modulus, elongation at the break, and the antibacterial effect of the films increased by 40%, 19%, 44%, and 23%, respectively, compared to unfilled film when the filler concentration was 0.5–1 wt.%. [ABSTRACT FROM AUTHOR]