Search

The use of a reflector can increase the solar radiation on the photovoltaic module (PV) surface, whereby the energy output can be improved. However, the economic feasibility may need to be considered too. This study is conducted, for the first time, due to the lack of studies regarding the economic feasibility assessment of implementing reflectors under the Malaysian meteorological conditions. The outcome will give information about the suitability for implementing a PV reflector in Malaysia through an experimental setup at a sewage treatment site, for two months in 2022. The Malaysian meteorological data, which include daily solar radiation, ambient temperature and wind velocity, were collected to study the output energy, efficiency and the economic perspective of a PV. In February 2022, the PV was operating without a reflector and the averaged values for the monthly solar radiation, ambient temperature and wind velocity were 539.9 MJ/m2, 28.4 °C and 2.2 m/s, respectively, which resulted in an output energy of 106.43 kWh. On the other hand, for April 2022, the PV was operating with a reflector. With the respective averaged input parameters 544.98 MJ/m2, 28.9 °C and 1.51 m/s, the output energy was 121.94 kWh. It is thus shown that the PV with a reflector increases the PV's output energy by 14.57%. Also, it is shown that the cost-effective factor value is 0.955 which means that the PV reflector is economically feasible to be implemented under the Malaysian meteorological conditions. Hence, extensive research should be conducted to improve the performance of PV reflectors. The findings of this paper maybe useful for researchers and/or manufacturers of PV reflectors. [ABSTRACT FROM AUTHOR]

Energy is one of the basic inputs and driving forces for economic and social development modernization. Sustainable energy supply is one of the major challenges in the modern world. Sustainable energy supply can be obtained through alternative energy sources, and efficient energy use is a high priority to optimize the environmental impact. This paper investigates the potential for energy savings involving five end-load equipment in academic institutions. The saving potential is obtained through energy efficiency analysis and feasibility analysis of the solar power generation systems. An energy audit is conducted on end-use consuming equipment (i.e., fans, lights, air conditioning, ICT equipment, etc.) in these five end-load sectors to find out the major energy-consuming equipment, energy consumption, and potential energy savings. The analysis of energy consumption per equipment helps determine the appropriate type of equipment to be upgraded and replaced for energy saving. The feasibility of rooftop solar power generation has been also analysed to integrate into the energy end load. The research findings confirm that laboratory equipment, lighting, and air conditioning are vital to energy consumption in academic buildings. The energy savings, bill savings, and carbon emissions reductions have been estimated based on integrating rooftop solar power generation. The feasibility analysis of onsite energy generation using a hybrid solar system found that the total energy-saving potential and bill savings within five years are 311,131 kWh and RM 113,563, respectively. This value refers to comprehensive energy-saving and bill for all academic buildings involved in this research. [ABSTRACT FROM AUTHOR]

• Hybrid solar desalination system. • Active mode operation and passive mode operation. • Solar desalination systems efficiency and economic analysis. • Trend in distillate cost, and yield by hybrid solar desalination systems. • Innovation type, feedwater, weather variabilities, operation mode impact on distillate quantity. In this paper, a hybrid solar desalination system was fabricated and incorporated with a water heater powered by a photovoltaic (PV) system. It was experimentally evaluated at Universiti Teknologi Petronas, Malaysia. Daytime operating conditions without the use of a PV system were considered for the conventional operation, while the use of PV alone or combined with direct solar radiation was considered as the modified system. This study was carried out to determine the freshwater yield, weather variabilities impact on yield, economic analysis, and system efficiency of hybrid solar desalination systems. An encyclopaedic review of five years of different researchers from different countries was critically analysed and compared with this study to see their trends and relationship. Within the study period, solar still distillate cost ranges from 0.0051 to 0.8857$/L, and 0.006 to 0.789$/L for the modified and conventional systems respectively. Similarly, the distillate cost for this study is 0.0374$/L and 0.0892$/L for the conventional and modified systems respectively. Also, the distillate yield ranges from 0.93 to 24.3 L/m2.day with an average of 12.1 L/m2.day, for the modified system, and 0.55 to 6.63 L/m2.day with an average of 3.35 L/m2.day for the conventional systems. The hourly system efficiency is 30.07 %, and 8.29 % for the modified and conventional systems respectively. Solar still is economically reasonable with good efficiency as obtained from the result. The findings also suggested that researchers should target a distillate yield of at least 6 L/m2.day and a distillate cost of 0.2$/L or lower for innovation, for a good and economical system. [ABSTRACT FROM AUTHOR]

Malaysia is one of the leading producers and exporters of oil palm, and the industry contributes significantly to the growth of the national economy. Nonetheless, the consequential oil palm biomass (OPB) with a potential yield of ∼97 million tonnes annually presents both challenges and opportunities, demanding innovative waste management solutions. This paper explores the feasibility of converting OPB into valuable commodities by employing concentrated solar-driven pyrolysis. A detailed overview of the biomass produced from oil palm plantations and mills is provided, along with a discussion of the industry stakeholders and associated biomass management challenges. The pyrolysis of OPB is explored, emphasizing benefits, potential barriers, and techniques. The focus then shifts to Malaysia's solar potential, which ranges from 1470 to 1900 kWh/m2 annually. The potentials of solar pyrolysis are explored, encompassing discussions on solar concentrator types, reactors, and the distribution of solar and OPB resources throughout Malaysia. The paper then recommends Tawau in Sabah, as an ideal location for OPB solar pyrolysis, due to its solar availability (up to 1873 kWh/m2), potential OPB resources from 19 mills and 241 plantations, and supportive infrastructure. The paper proposes solar-driven pyrolysis as a sustainable solution for Malaysia's OPB management, offers insights for policy initiatives and technological innovations in optimizing OPB and solar energy utilization. • Analyzes oil palm biomass potential for solar pyrolysis in Malaysia. • Explores solar resources in Malaysia for solar-driven pyrolysis. • Examines solar concentrators and reactors for pyrolysis. • Identifies potential city, as the optimal location for solar pyrolysis. • Discusses commercialization challenges of solar-driven pyrolysis. [ABSTRACT FROM AUTHOR]

Recent research has focused on the design and sizing of standalone photovoltaic systems. Unfortunately, due to highly fluctuating levels of solar energy and the power supply generated not coinciding with energy demand, high capacity of generation and energy storage systems are required to provide a highly reliable supply. However, a highly reliable system tends to produce high excess energy which needs to be discarded as a dump load, which is proving to be a major concern. For this reason, this paper proposes to use the excess energy for hydrogen production, which will then be sold to local consumers. This paper presents a comparison of optimization design and economic analysis of a standalone photovoltaic with a battery system and a standalone photovoltaic with battery-hydrogen production system using an iterative technique. For the feasibility study of the standalone photovoltaic with a battery and with a hydrogen production system, the proposed minimum hydrogen-selling price is determined by breakeven analysis and is compared to the past references' hydrogen-selling prices and gasoline prices. • Optimization design, modeling, and economic analysis of SAPV without and with hydrogen production system were studied. • Iterative technique was used in optimization process. • Optimization results for SAPVBS and SAPVBHPS were compared. • Breakeven point analysis of the payback period and the return of investment were used to determine hydrogen-selling price. • Theminimum hydrogen-selling price was compared to the past published hydrogen-selling prices and Malaysia's gasoline prices. [ABSTRACT FROM AUTHOR]

This paper presents a detailed target-oriented performance assessment of a 232.5 kWp grid-connected solar PV (GCPV) system installed on a commercial building in Malaysia. Technical and meteorological data for 2019, in 5-min intervals, was retrieved from the solar data logger. The GCPV system generated about 301.5 MWh of energy in 2019, almost achieving the stated target of 305.0 MWh. While most months in 2019 successfully achieved the set monthly target, some did not due to low solar irradiance. The Performance Ratio (PR), Capacity Utilization Factor (CUF), system efficiency, and Levelized Cost of Energy (LCOE) were found to be 85.4%, 14.85%, 9.15%, and 0.396 MYR/kWh, respectively. The PR of the present GCPV system was higher than other GCPV systems surveyed. Approximately 177 metric tons of CO 2 emissions were saved during the year after installing the GCPV system. In addition, performance models, based on the key factors of solar irradiation and PV module temperature that affect the yield and power output of the GCPV system, were developed and tested statistically. The findings of this study should be of use to solar energy customers and stakeholders. [Display omitted] • A target-oriented performance analysis of grid-connected solar PV (GCPV) system is assessed. • Actual yield of GCPV system achieved about 90% of the set target yield. • The annual PR, CUF, and system efficiency was 85.4%, 14.85%, and 9.15%, respectively. • The payback period and LCOE was ∼8 years and 0.396 MYR/kWh, respectively. • About 177 metric tons of CO 2 was reduced due to GCPV system. [ABSTRACT FROM AUTHOR]

Application of solar energy in Malaysia has been started in 1998. This country has a large potential of solar energy due to its location at equatorial region. The current energy consumption and demand in Malaysia is describes in this paper. The potential of solar energy in Malaysia is described together with the suitable photovoltaic construction. It also explains the plans conducted by Malaysia involving solar energy that covers investments and also projects involved such as Malaysia Building Integrated Photovoltaic (MBIPV). Simulation of grid-connected photovoltaic system in this study is performed using HOMER software. Finally, the potential of having a grid-connected PV system in a residential area is analyzed. The positive and negative findings in terms of cost and suitability of the system are explained. [ABSTRACT FROM AUTHOR]

Nowadays, even though many researchers continue to investigate and study about Parabolic Dish based on Concentration Solar Power (CSP), the findings are not conclusive and do not provide accurate evidence and proof on the potential of CSP development in Malaysia. The missing link in the Parabolic Dish (PD) Stirling Engine system modelled is the control systems, which vary the amount of working gas in the Stirling engine. The temperature of the heater in PD system which has been modelled is overheated and causes damage to the heater material, low output efficiency, high thermal losses and effect to the lifespan of the PD system. Therefore, the primary aim of this paper was to design a control system to maximize output efficiency during a normal operation by maintaining the heater/absorber temperature at the highest safe operating point and preventing excessive range of threshold to prevent damage to the heater material. [ABSTRACT FROM AUTHOR]

Abstract: The limited availability of fossil energy carriers and environmental impact of energy consumption demand mid- and long-term strategies both for the rational use of energy and for increased renewable energy utilization. Despite the establishment of the National Energy Policy, there is still an obstacle in reaching those objectives and targets. In the 7th Malaysia Plan for instance, the government has highlighted that a third of the Government''s total allocation of RM469 million for rural electrification programmes under the has been allocated for the provision of solar powered installations for rural and remote communities. This paper outlines a detailed description of various existing solar technologies, the understanding of each technology and its associated challenges, which will provide a suitable basis to recognize advantages and drawbacks in its implementation in Malaysia. The paper finally justifies some of the barriers in promoting the full scale utilization for the solar energy in Malaysia. [Copyright &y& Elsevier]

Due to environmental issues and the upward trend of fossil fuel prices, the study of renewable energy (RE) based generation and their effects on the electrical system has become an important part of the government's energy policies and university projects. In RE generation, as solar photovoltaic (PV) systems are modular, silent, and transportable and demonstrate ease of installation, they have attracted a greater amount of attention specifically in those areas which receive considerable average solar radiation per day such as Malaysia. However, connecting solar PV farms to the grid like any other distributed generation (DG) units poses serious issues which arise in the distribution network. This paper presents a novel fault location algorithm based on the recording of short circuit power values at the primary substation of unbalanced radial distribution networks including PV systems. The recorded values are evaluated by a designed and tuned multi-layer feed forward neural network and the fault distances from the source are estimated accordingly. In order to highlight the accuracy of the presented method, the scenario is also repeated by recording the peak values of short circuit current which have been mostly used in the published intelligent fault location studies and the obtained results via two different values are compared with each other. The results reveal that the presented algorithm using a small scale input set is able to precisely locate different fault types in the unbalanced distribution networks including DG units. [ABSTRACT FROM AUTHOR]

Abstract: Solar energy is one of renewable energy sources which have potential for future energy applications. New technology developments in solar energy utilization are expected to result in the improvement of the photovoltaic performance with lower production cost. This will increase the demand and viability for commercial applications. The current popular technology converts solar energy into electricity and heat separately. The photovoltaic-thermal (PV/T) hybrid system is designed to generate thermal and electrical energy simultaneously. It is well known that using a hybrid system can eliminate the need for external source of electrical energy. This paper presents research and development activity being carried out at Solar Energy Research Institute (SERI), Universiti Kebangsaan Malaysia in order to realise the technology. [Copyright &y& Elsevier]

Abstract: This paper examines solar photovoltaic (PV) in Malaysia. First, it analyzes the current energy demand in Malaysia and discusses some of the national policies and the installations of solar PV in urban and rural areas in the country. Next, the general Feed-In Tariff (FiT) scheme is explained, indicating its potential as one of the investment options for Malaysians. Finally, the loan financing option for solar PV is presented, providing examples that have been implemented in other countries, as well as explaining the Green Technology Financing Scheme (GTFS) for companies and the proposed soft loan scheme for individual households in Malaysia. It also analyses the impact of the proposed interest rate to household consumers in Malaysia, in terms of total profit, net present value and internal rate of return. It is found that the FiT scheme could potentially help in increasing renewable energy penetration, particularly for solar PV. To provide upfront capital for solar PV installation, it is shown that the GTFS is a good financial source for companies while for individual home owners, a soft loan facility from banking institutions is a feasible source if the interest rate is 5% or less. [Copyright &y& Elsevier]

Abstract: Predicted to be the clean energy of tomorrow, solar energy has been in the forefront of energy development in many developed countries and a potential source of energy to developing countries like Malaysia. This paper presents Malaysia''s solar energy or solar photovoltaic developmental outlook. The study is done by first looking into the country''s energy policies related to solar energy. Key players in the solar energy development such as government institutions are introduced. Early solar energy programmes and a key project called Malaysia Building Integrated Photovoltaic (MBIPV) as well as its successful initiatives will be presented. Measures which have taken by the government of Malaysia including attractive incentives to encourage solar photovoltaic development, the country''s potential in solar energy, foreign investments and future directions as well a feed-in tariff scheme will be presented in length to provide a broad spectrum of solar energy development in Malaysia. The outlook has been positive and the country is active in promoting solar as an alternative energy and is aware of benefits it will bring toward its economic development in the future. [Copyright &y& Elsevier]

Abstract: Malaysia is situated at the equatorial region with an average solar radiation of 400–600MJ/m2 per month. It has a promising potential to establish large scale solar power installations; however, solar energy is still at the infancy stage due to the high cost of photovoltaic (PV) cells and solar electricity tariff rate. The Malaysian government is keen to develop solar energy as one of the significant sources of energy in the country. According to the 9th Malaysia Plan (9MP), a large allocation had been dedicated for implementation of solar PV systems. On 25th July 2005, a Malaysian Building Integrated Photovoltaic (MBIPV) project had been announced and it was planned to end by 2010. The project consists of three categories which include: BIPV demonstration, national “SURIA1000” and BIPV showcase. Greater emphasis will be placed on energy efficiency under the Tenth Malaysia Plan (2011–2015). This paper discusses present and future situation of solar power in Malaysia, utilization of solar energy and the strategies taken by the Malaysian government and Non-Government Organizations (NGOs) to promote solar energy thermal applications and electricity power generation in the future. [Copyright &y& Elsevier]

This paper presents a MATLAB based user friendly software tool called as PV.MY for optimal sizing of photovoltaic (PV) systems. The software has the capabilities of predicting the metrological variables such as solar energy, ambient temperature and wind speed using artificial neural network (ANN), optimizes the PV module/ array tilt angle, optimizes the inverter size and calculate optimal capacities of PV array, battery, wind turbine and diesel generator in hybrid PV systems. The ANN based model for metrological prediction uses four meteorological variables, namely, sun shine ratio, day number and location coordinates. As for PV system sizing, iterative methods are used for determining the optimal sizing of three types of PV systems, which are standalone PV system, hybrid PV/wind system and hybrid PV/diesel generator system. The loss of load probability (LLP) technique is used for optimization in which the energy sources capacities are the variables to be optimized considering very low LLP. As for determining the optimal PV panels tilt angle and inverter size, the Liu and Jordan model for solar energy incident on a tilt surface is used in optimizing the monthly tilt angle, while a model for inverter efficiency curve is used in the optimization of inverter size. [ABSTRACT FROM AUTHOR]

Abstract: In this research, an optimisation for building integrated hybrid PV/diesel generator system for zero load rejection for Malaysia is performed. The optimisation is performed considering a loss-of-load probability (LLP) less than 0.01. However, the daily averages of solar energy for Malaysia and a mathematical model of a hybrid PV/diesel generator system are used in this optimisation. The optimisation presented in this paper aims to calculate the optimum capacities of a PV array and diesel generator, which investigate the minimum system cost. An optimisation problem in terms of system units’ cost is solved graphically in this study. Moreover, the optimised system is compared to other energy source choices to highlight its feasibility. The recommended configuration of a PV/diesel system located in Malaysia is CA =1.2, CDG =0.3, while the optimum CB is 0.1. The results of the optimisation show that a PV/diesel generator choice is more feasible compared to a standalone PV system or diesel generator system because it reduces the system cost by 35%. [Copyright &y& Elsevier]

Abstract: This paper aims to present the feed-in tariff (FiT) outlook in Malaysia, which is in the process of being enacted through a Renewable Energy (RE) Policy by the Government of Malaysia (GoM). A brief in policies leading towards the RE policy and the potential of each RE sources under FiT mechanism have been discussed. The successful utilisation of RE source in electricity generation and the FiT implementation globally are positive indicators to implement FiT in Malaysia. Potentials of FiT on biomass, biogas and solid waste energy are currently very promising in Malaysia, but it is solar energy which is predicted to be the main RE of the future, surpassing all other REs. [Copyright &y& Elsevier]

Abstract: Solar energy is the most promising source of clean, renewable energy and it has the greatest potential of any power source to solve the world''s energy problems. However, the problem, is how best to harness this vast amount of solar energy. Nevertheless, even if highly efficient Concentrating Solar Power (CSP) could be made cheaply, there would be considerable change in solar power. This technology is expected to be more efficient and to achieve a manufacturing cost of less than $1/W near future. This paper reviews and elaborates the methodology utilized to design and fabricate the solar dish concentrator and outlines the parameters that can be used to increase the efficiency of solar fraction in parabolic dish concentrator under wet climate environment in Malaysia. The study finally provides ideas to the continually increasing ability of these technologies to concentrate and harness solar energy for electricity production and thus eliminate the growing concern over climate change and how it will hurt the region''s environment, human health and economy. [Copyright &y& Elsevier]

COVID′19 pandemic has devastated several industries and solar energy is no exception. In its economic relief package, Malaysia has announced approximately US$ 2.9 billion in expenditure for the installation of new grids, LED street lights and rooftop solar panels. The Government will also open the tender for a 1400 MW solar power project in the year 2020, which is expected to generate 5 billion ringgit (US$1.1 billion) in investments. As these measures are intended to sustain the existing growth of solar energy potential in the country, it is vital to assess its status quo. Hence, this paper aims to review the current status of renewable energy in Malaysia as well as the initiatives taken before the pandemic to promote solar photovoltaic (PV) technology to meet the energy demands through the low-carbon pathway. • Solar technologies and factors affecting renewable energy in Malaysia. • Initiatives and different policies implemented by the Malaysian government. • Carbon-neutral Malaysia beyond Covid'19 pandemic. • Comparison between the ASEAN countries and their strategies to reach renewable energy goals. [ABSTRACT FROM AUTHOR]

The recent proliferation of residential solar photovoltaic systems has prompted several technical challenges to the operation of low voltage (LV) distribution networks. More specifically, the mismatch of the solar generation and demand profiles, particularly during the midday when the demand is low and solar generation is high, can lead to network overvoltages and increased network losses. In addition, the solar photovoltaic system is not able to reduce the system's maximum demand, given the residential LV network would normally have an evening peak when the sun goes down. In this regard, this paper examines two different control strategies in designing the battery energy storage system. One aims to eliminate reverse flow caused by the surplus solar energy and the other aims for peak demand reduction. [ABSTRACT FROM AUTHOR]