Search

Abstract: An optically accessible single-cylinder high-speed direct-injection (HSDI) diesel engine was used to investigate the spray and combustion processes for biodiesel blends under different injection strategies. The experimental results indicated that the heat release rate was dominated by a premixed combustion pattern and the heat release rate peak became smaller with injection timing retardation. The ignition and heat release rate peak occurred later with increasing biodiesel content. Fuel impingement on the wall was observed for all test conditions. The liquid penetration became longer and the fuel impingement was stronger with the increase of biodiesel content. Early and late injection timings result in lower flame luminosity due to improved mixing with longer ignition delay. For all the injection timings, lower soot luminosity was seen for biodiesel blends than pure diesel fuel. Furthermore, NO x emissions were dramatically reduced for premixed combustion mode with retarded post-TDC injection strategies. [Copyright &y& Elsevier]

Abstract: Biodiesels are promoted as alternative fuels and their applications in diesel engines have been investigated by many researchers. However, the particle size distribution emitted from heavy-duty diesel engines fueled with palm-biodiesel blended with premium diesel fuel and paraffinic fuel blended with palm-biodiesel has seldom been addressed. Thus, five test fuels were used in this work to study the particle size distribution: D100 (premium diesel fuel), B100 (100% palm-biodiesel), B20 (20vol% palm-biodiesel+80vol% D100), BP9505 (95vol% paraffinic fuel+5vol% palm-biodiesel) and BP8020 (80vol% paraffinic fuel+20vol% palm-biodiesel). A Micro-Orifice Uniform Deposit Impactor (MOUDI) equipped with aluminum filters was used to collect size-resolved samples. Experimental results indicated that palm-biodiesel blends and paraffinic fuel blends could improve combustion efficiency in diesel engines, but pure palm-biodiesel could cause incomplete combustion. Adding palm-biodiesel to diesel fuel would slightly increase particles with diameter <0.31μm but paraffinic fuel blends could decrease particles with diameter <1μm. The mass median diameter of overall particles (MMDo) and σ g,o are 0.439μm and 3.88 for D100; 0.380μm and 3.24 for B20; 0.465μm and 4.22 for B100; 1.40μm and 4.92 for BP9505; 1.46μm and 2.25 for BP8020. There are more particles with low aerodynamic diameters (diameter <0.31μm) in the exhaust of D100, B20 and B100 fuels. On the other hand, a greater fraction of particulate matter of BP9505 and BP8020 existed in coarse particles (diameter: 2.5–10μm). Energy efficiency also increases significantly by 12.3–15.1% with the introduction of paraffinic fuel blends into the engine. Nevertheless, paraffinic fuel blends also reduce the emission of particulate matters by 36.0–38.4%. Carbon monoxide was decreased by 36.8–48.5%. Total hydrocarbon is 39.6–41.7% less than diesel fuel combustion. Nitrogen oxides emission is about 5% lower for paraffinic fuel. These results show that paraffinic fuel can be very competitive and replaced diesel fuels in the future. [Copyright &y& Elsevier]

Abstract: This study investigated polycyclic aromatic hydrocarbon (PAH) and regulated harmful matter (traditional pollutant) emissions, fuel consumption, and the assessment of the inferior condition of engine oil from heavy-duty diesel engines (HDDEs) fueled with palmbiodiesel–PDF (premium diesel fuel) blends and paraffinic–palmbiodiesel blends under brand-new (the mileage was zero) engines accumulated mileage test. Experimental results indicated that the emissions of THC and CO increased with operation time but the emissions of NO x and PAHs decreased with operation time between 0 and 300h (18,000km). Using palmbiodiesel–PDF blends or paraffinic–palmbiodiesel blends instead of PDF in HDDEs reduced the emissions of THC (10.7–44.2%), CO (0.664–15.6%), CO2 (0.763–2.55%), NO x (1.25–4.97%), PM (6.11–26.8%), total PAHs (43.0–90.2%) and total BaPeq (63.1–89.6%) significantly. [Copyright &y& Elsevier]

Abstract: Biodiesels have received increasing attention as alternative fuels for diesel engines and generators. This study investigates the emissions of particulate matter (PM), total carbon (TC), e.g., organic/elemental carbons, and polycyclic aromatic hydrocarbons (PAHs) from a diesel generator fuelled with soy-biodiesel blends. Among the tested diesel blends (B0, B10 (10vol% soy-biodiesel), B20, and B50), B20 exhibited the lowest PM emission concentration despite the loads (except the 5kW case), whereas B10 displayed lower PM emission factors when operating at 0 and 10kW than the other fuel blends. The emission concentrations or factors of EC, OC, and TC were the lowest when B10 or B20 was used regardless of the loading. Under all tested loads, the average concentrations of total-PAHs emitted from the generator using the B10 and B20 were lower (by 38% and 28%, respectively) than those using pure petroleum diesel fuel (B0), while the emission factors of total-PAHs decreased with an increasing ratio of biodiesel to premium diesel. With an increasing loading, although the brake specific fuel consumption decreased, the energy efficiency increased despite the bio/petroleum diesel ratio. Therefore, soy-biodiesel is promising for use as an alternative fuel for diesel generators to increase energy efficiency and reduce the PM, carbon, and PAH emissions. [Copyright &y& Elsevier]