Search

Bubbles, as typical defects of oil–paper insulation systems, pose a great threat to the insulation state. In this article, the characteristics and mechanisms of the partial discharge (PD) inception, evolution, and induced breakdown of bubbles embedded between oil-impregnated paper (OIP) layers are investigated. The results show that the PD inception has a significant statistical time delay due to the lack of free electrons. The PD inception time delay (PDTD) follows an exponential distribution and leads to the large dispersion of the PD inception voltage (PDIV), which follows a Weibull distribution. The changes in PD behavior [charge, repetition rate, pulse current waveform, and phase-resolved PD (PRPD)] over time all show two separable stages (stages 1 and 2). The continuous recording of bubble area and gas composition under PD reveals that the evolution of bubble PD is attributed to the change in gas composition rather than the change in surface conditions as believed by researchers. The OIP breakdown induced by bubble PD indicates two breakdown modes, fast and slow, which correspond to direct-induced breakdown in stage 1 and cumulative-damage breakdown in stage 2. The former occurs because of the severe distortion of the electric field by the space charge at the head of the discharge channel inside the bubble, whereas the latter occurs because of the gradual deterioration of the OIP due to the continuous PD action. This study increases our understanding of the mechanisms of bubble discharge and of oil–paper insulation deterioration, and it provides guidance for fault diagnoses. [ABSTRACT FROM AUTHOR]

Even for gas-insulated metal-enclosed switchgear (GIS) equipment that has passed an on-site dielectric test, some dielectric failure can occasionally occur without warning. It is necessary to evaluate the effectiveness of on-site dielectric tests of GIS equipment. In this study, two standard test procedures, power-frequency partial discharge (PD) and lighting impulse (LI) withstand test, were carried out in a real model test platform of 550 kV GIS to evaluate the effectiveness of on-site dielectric tests. Through experiments, the minimum detectable defect sizes were determined for different curvature radius values. The results show the limitation of the power-frequency PD test and the need to use of the LI withstand test as supplementary assessment on site. Two calculable constraints of defect detectability were proposed to extend the results to GIS equipment at other voltage levels. The results clarify the cause of dielectric failure without any warning and provide technological guidance for manufacturing and installation. [ABSTRACT FROM AUTHOR]

The standard lightning impulse (LI), defined as a smooth full lightning impulse voltage having a front time of 1.2 ?s and a time to half-value of 50 ?s, obtained from field observation, has remained unchanged from IEC Ed. 1 in 1962 through to Ed. 3 in 2010. LI test plays an important role in the equipment design and insulation defects detection. In order to evaluate the reasonability of the standard LI waveform from the point of insulation characteristics, breakdown characteristics of GIS under LI with different wavefront times Tt and wavetail times Tt were studied. Those experimental results show that the LI waveform parameters have little influence on the breakdown characteristics of a sound GIS equipment, but have great influence on the GIS equipment with defects. For a highly inhomogeneous electric field, with the wavefront time increasing, the 50% breakdown voltages U50% have remarkable change and the U50%?Tt curve tends to be U-shaped. The 50% breakdown voltages decrease significantly with the increase of impulse wavetail time, especially when wavetail time is in the range of 1.5 to 15 ?s, but the difference of the values decreases after 15 ?s. Ignoring the generating possibility in the field for the large series inductance and load capacitance, a LI with wavefront time in the range of 0.2 to 0.7 ?s is proposed in the field for it may increase the probability of detecting insulation defects. Finally, the polarity reversion phenomenon and critical radius phenomenon, observed from the breakdown characteristics, can be explained by the migration and diffusion of space charges. [ABSTRACT FROM AUTHOR]

For the application of SF6/N2 in power equipment such as GIS and GIL, the breakdown characteristics of SF6/N2 in varying electric field non-uniformity under standard lightning impulse were studied in this paper based on a lightning impulse experimental platform. The research indicates that the reversal of polarity effect appears in SF6/N2 gas mixtures. That is, when the pressure is relatively low, the 50% breakdown voltage under positive polarity is lower than which under negative polarity. When gas pressure reaches the critical pressure, the situation would be opposite. The augment of SF6 mixing ratio or decrease of electric field non-uniformity would both result in the decline of the critical pressure. Meanwhile the change of polarity effect with SF6/N2 is later than that with pure gas with the increase of electric field non-uniformity. In addition, the phenomenon of critical radius of SF6/N2 gas mixtures was found. The critical radius reduces with the increase of gas pressure and is smaller under positive lightning impulse than negative. And the phenomenon of critical radius with pure gas is more obvious than that with gas mixtures. [ABSTRACT FROM AUTHOR]

Discharges in liquid obey time effect, pressure effect and scale effect. Traditional formulas are usually applied in a narrow range to keep the formula form consistent with Martin?s formula. In this paper, we have developed a new empirical formula for the electric strength of transformer oil depending on pulse duration, hydrostatic pressure and gap geometry in form Εbr = κe at-beff Ρ/,sub>spl gamma/ A>sub>-Β d-ϵ to be applied in a wider range. In this formula, the time dependent pressure effect is represented by constant γ, which can be expressed as γ=ape -bpt-c>peff . Time effect, area effect and distance effect are represented by e at-beff, Β and ϵ, respectively. For transformer oil, κ=0.42, a=0.53, b=0.23, ap=0.14, bp=0.93, cp=0.41, Β=0.1 and ?=0.25?0.06, with Ebr, teff, P, A and d in MV/cm, μs, MPa, cm2 and cm, respectively. [ABSTRACT FROM AUTHOR]

A new method was introduced to evaluate and analyze synergistic effect including negative synergistic effect of SF₆/N₂ gas mixtures breakdown voltage. This method provides an intuitional comparison among different degree of synergistic effect through a simple equation of the normalization coefficient h. The disadvantages of traditional method, which fails to evaluate negative synergistic effect and would be inaccurate when breakdown voltages of the two gas compositions are close, are overcome via the method. In this paper, a typical example of the above is shown to analyze synergistic effect and abnormal negative synergistic effect of SF₆/N₂ gas mixtures in non-uniform electric field under lightning impulse. Meanwhile the validity of the normalization coefficient h with the synergistic effect of SF₆/N₂ gas mixtures under various voltage conditions and electrodes in references was verified. [ABSTRACT FROM PUBLISHER]

Gas-insulated switchgear (GIS) might withstand ac/lightning impulse (LI) superimposed voltage caused by lightning intrusion or switching operation during operation. When there are insulation defects, the breakdown probability is greatly increased, which threatens the safety of GIS and needs to be further studied. In this study, the discharge characteristics of two typical insulation defects, including a metallic protrusion on bus bar and foreign matter attached to insulator, under ac/LI superimposed voltage were studied, and the influence of superimposed phase, polarity, and ratio was investigated. It was found that, under a quasi-uniform electric field, the superimposed breakdown voltage (${U}_{s}$) was the same as the LI breakdown voltage (${U}_{\text {LI}}$). However, when there were insulation defects, ${U}_{s}$ was significantly affected by the superimposed phase and polarity. For the metallic protrusion, the most critical condition was an −LI superimposed at $\varphi =90$ , with ${U}_{s}$ decreasing by 11% relative to ${U}_{\text {LI}}$. For the metallic particle attached to insulator, when an +LI was superimposed at $\varphi = 0^{\circ }$ or −LI at $\varphi = 180^{\circ }$ , ${U}_{s}$ decreased most, by as much as 19.6% relative to ${U}_{\text {LI}}$. Finally, the validation test was performed in a 110-kV GIS with insulation defects and ${U}_{s}$ was 7%–14% lower than ${U}_{\text {LI}}$. The results showed that, under a proper superimposed phase and polarity, ${U}_{s}$ could be significantly lower than ${U}_{\text {LI}}$ of GIS with insulation defects, indicating the great potential of the ac/LI superimposed voltage test for the high-sensitive detection of GIS insulation defects. [ABSTRACT FROM AUTHOR]

By using 1 MV Marx generator and a 220 kV GIS bus, an experiment platform has been established, and a stainless steel needle is applied to simulate spike defect, so as to study the influence of pressure, wave front time and electric field on 50 % breakdown voltage (U50) and voltage-time (V-t) characteristics of SF6 gas gap with existence of a spike defect on the bus of GIS under double exponential impulse voltage. When wave front time is short, 50% breakdown voltage of the SF6 gap hardly changes with various pressures, and U50%-P curve turns to be a hump shape when wave front time increases. However, pressure has no significant effect on V-t characteristics. The slope of V-t characteristics curve is negative when wave front time of applied voltage is short (0.08~0.9μs), and it will turn to be positive when wave front time becomes longer (several ~15μs). A new method to fit these V-t characteristics curves under impulse voltage with longer wave front times is proposed. It is found that 50 % breakdown voltage decreases almost linearly with the increase of electric field non-uniformity factors (f), and V-t characteristics cluster with valley-like profile have been drawn at different f. Dispersion of V-t characteristics cluster reduces and the flat region expands with the increase of f, and minimum value of breakdown voltage of SF6 gap with spike defect under impulse voltage, which is of guiding significance for engineering, can be obtained. [ABSTRACT FROM AUTHOR]