Search

Starting from the updated requirements of an advanced laser system, a switch–trigger system for a 2.0-MJ pulsed power supply (PPS) module is developed. This paper discusses the design, construction, and testing of this switch–trigger system. The two-electrode construction for the spark gap switch is selected because of its superiority in terms of long working life, high peak currents, and fast rise time of currents. The trigger generator based on resonant charging of a pulse transformer is constructed. A magnetic isolator and a pressure controller are the auxiliary equipment of this system. In the section based on mathematical principles, the equations of the lifetime and stability of this spark gap switch with graphite electrodes are given. These expressions can be regarded as the design basis of the same type of switch. As for the trigger generator, the analysis states that an appropriate ratio can be obtained when using the resonant charging based on a core-type pulse transformer. The charging time is dependent on the leakage inductance and the capacitance of the primary and secondary capacitors. Extensive testing proves the operating parameters of the switches and the trigger generator. The measured discharge current waveform of the 2.0-MJ capacitive PPS module is demonstrated to be over 500 kA peak current and 500 \mus pulse width. The life test proves that the switch–trigger system can support more than 200 kC transfer charge. By replacing the electrodes, the lifetime of this switch can be extended furthrer. [ABSTRACT FROM PUBLISHER]

The limited lifetime in a high current is the main drawback of spark-gap switches. Electrode replacement is an easily suggested method to extend the lifetime. In order to perform electrode replacement, thermal damage caused by heating effect should be prevented at the static electrical contact interfaces between the electrodes and the holders. Based on the Holm model, the Hertz formula, and the heat conduction theory, a mathematical model of the contact temperature rise is proposed in this paper. This mathematical model can prove quantitatively that the pulse-current integral (action integral), material physical properties, and mechanical characteristics of spark-gap switches are key parameters affecting the temperature rise. The action integral is determined by the electrical parameters. Material physical properties include the thermal conductivity, the specific heat, the density, the electrical resistivity, the elasticity modulus, and the Poisson ratio. Mechanical characteristics of spark-gap switches include the contact radius/area, the contact force, and the contact surface roughness. The implementation of electrode replacement depends on the reasonable configuration of these key parameters. The experiments in a 1.2-MJ power supply module give that the phenomenona correspond with our analysis. Based on the analysis in this paper, an electrode holder structure is proposed as a practical solution for extending the useful lifetime of spark-gap switches with graphite electrodes. [ABSTRACT FROM PUBLISHER]

High-power closing switches with graphite electrodes have been used in power-supply system for a large laser pump. The useful lifetime of this kind of switch is an interesting and important issue. Previous researchers have observed that the graphite erosion loss is proportional to the amount of transfer charge in a high-power pulsed discharge. Therefore, the erosion rate of graphite may be used for predicting and estimating the electrodes' useful lifetime. According to the mathematical model proposed in this paper, the lifetime of a closing switch with graphite electrodes is dependent upon several key parameters, including the dimensions of electrode, density, the erosion rate of graphite electrodes, undervoltage ratio, working temperature, and the amount of energy transfer. A mathematical formula describing the relationship between lifetime and those parameters has been deduced. Based on a newly developed spark-gap switch which can support over 100-C single transfer charge, this proposed lifetime model has been verified. This paper may quantitatively perform the function of guidance in engineering applications of graphite electrode switches in large pulsed-power facilities. [ABSTRACT FROM AUTHOR]

In a high-power laser facility with multiplex power modules, the dispersion of self-breakdown voltages of spark gap switches might result in a so-called pre-fire problem. Pre-fire probability of spark gap switches with graphite electrodes must be constrained at extremely low level. In this paper, Pedersen model was used to explain the causes of pre-fire. The microscopic surface roughness of worn graphite electrodes had a major impact on pre-fire. And this paper had deduced the cumulative probability distribution of pre-fire, and given a relevant Weibull distribution equation. Several typical graphite materials were tested too. The experimental results revealed that electrodes should use graphite with higher hardness, smaller particle size and greater flexural strength. This was consistent with the analysis of Pedersen model. More significantly, based on the experiments of typical graphite materials, two Weibull constants of the cumulative probability distribution of pre-fire were obtained by a graphing method. Therefore, it is possible to calculate, reduce or control the occurrence of pre-fire in a facility with many gas switches. Via optimizing the operating under-voltage ratio of multiplex switches, the expectable pre-fire probability can be achieved. [ABSTRACT FROM PUBLISHER]

Electrode replacement is an effective method to extend the useful lifetime of the spark gap switch with graphite electrodes. In order to perform electrode replacement, suppressing temperature rise and preventing static welding/erosion should be considered for the static electrical contact interface between the electrode and the holder. In this paper, a mathematical model of contact temperature rise is proposed based on the Holm model and heat-conduction equations. This mathematical model can quantitatively prove that some material properties of the metal holder and some mechanical characteristics of the spark gap switch are key parameters affecting temperature rise. Material properties of the metal holder include thermal conductivity, specific heat, density, electrical resistivity, elasticity modulus, and the Poisson ratio. Mechanical characteristics of the spark gap switch include contact radius/area, contact pressure, and contact surface roughness. Optimum configuration of these key parameters reduces temperature rise and prevents static welding/erosion. [ABSTRACT FROM AUTHOR]

Two-electrode graphite spark gap switch (TGSGS) is used as the main discharge switch and triggered by a reliable trigger generator in pulsed power conditioning system (PPCS). There would be 108 energy modules in PPCS working at the same time. The reliable operating and jitters of the trigger generators will have impact on the PPCSs performance. In this paper, the working modes of the TGSGS are discussed and the performance of trigger generators in PPCS is tested and presented. A protection strategy of the trigger generator in PPCS is introduced, and effect of the blocking capacitor on the trigger pulse transmission is analyzed and tested. The protection strategy of the trigger generator based on blocking capacitor and fuse can effectively prevent the energy anti-irrigation failure when the pulse transformer core saturated. The blocking capacitor has some effect on the trigger pulse transmission, and has the larger capacitance, getting the higher peak amplitude on the cathode of the TGSGS. It is tried to discuss the working characteristics of the thyristors, and proposes a selection reference of the thyristors in this and other similar applications. The combination of analysis and measurement would be useful for the selection of thyristors and other components. [ABSTRACT FROM PUBLISHER]

In a high-powered single pulse system, the graphite electrode is better than other common metal electrodes for high energy transfer and pulse discharge. In this paper, the erosion mechanism of graphite electrode is investigated with the thermodynamics theory and the experimental results. Based on a simplified mathematical model, the graphite electrode erosion process of high-powered spark gap switch is also analyzed. The analysis results show that the relationship of the graphite electrode erosion and the charge transfer is linear, which is accordant with the experimental results. [ABSTRACT FROM AUTHOR]