Search

The focus of whey processing has been changed from waste treatment to the production of valuable products owing to the advancement of membrane technology. Producing high quality whey products at low energy consumption entails novel techniques for whey concentration. This study proposes forward osmosis (FO) as a potential approach to concentrate whey protein solutions, which is superior to the concentration via reverse osmosis (RO), mainly owing to the low hydraulic pressure during FO process. In particular, this work validated the feasibility of FO-based whey concentration using high-performance hollow fiber membranes that were fabricated in-house. The investigation focused on the effects of various operating conditions on the concentration performance. The experimental results reveal that optimal concentration efficiency would be achieved by appropriately choosing the cross-flow velocity, draw solution concentration and the maximum attainable concentration of whey protein solution. Especially, the flux decline behaviour as a function of the whey protein concentration in the feed solution indicated rapid formation of a polarized or gel foulant layer at the membrane surface. The proposed mechanism was supported by the investigation of physical cleaning with water, showing that the post-process cleaning after the concentration cycle was able to recover the membrane performance, whereas the intermediate cleaning during one concentration cycle had little impact on the concentration efficiency enhancement. This study has practical significance for the application of FO in the concentration of dairy streams and other liquid foods. [ABSTRACT FROM AUTHOR]

Abstract: Due to the unique properties of amphiphilic Pluronic block copolymers, they have been blended with other polymers such as PVDF to prepare membranes. Considering the stability issue, the strong pore-forming ability of Pluronic F127, and the mechanical strength of the resultant membranes, Pluronic/LiCl mixed additive consisting of a very low concentration of Pluronic has been used in this study. The effects of spinning conditions on PVDF hollow fiber fabrication have also been studied. It is found that the use of merely 0.2wt% of Pluronic is sufficient to impose significant impacts on the morphology, filtration performance, and mechanical properties of the resultant fibers. Hollow fibers spun using higher coagulant temperature, higher take-up speed, and water as the bore fluid exhibit better mechanical properties and filtration performance. PVDF hollow fiber membranes with PWP of 1180L/m2 hMPa and MWCO of 5kDa were obtained when spun with optimized spinning conditions and using 3wt% of LiCl and 0.2wt% of Pluronic as the mixed additive. The fibers can withstand a pressure of 0.55MPa from the lumen. [Copyright &y& Elsevier]

Abstract: Pressure retarded osmosis (PRO) is a promising membrane process to harvest the vast amount of free energy from the mixing of fresh and salty waters without adverse environmental impacts. A competent membrane for PRO should possess the features of high water permeability to allow water permeation, excellent salt rejection to maintain the osmotic driving force, low structure parameter to minimize the internal concentration polarization (ICP), and robust strength to withstand the required hydraulic pressure. In this work, we have developed a novel hollow fiber membrane by balancing these competing factors based on our prior experience in the thin-film composite (TFC) membranes. The newly developed TFC hollow fiber membrane can achieve a power density of 20.9W/m2 at a pressure of 15bar, using synthetic seawater brine (1.0M NaCl) as the draw solution and synthetic river water (1mM NaCl) as the feed water, respectively. The simultaneous specific reverse salt flux was found to be 0.03mol/L, which is much lower than reported flat-sheet membranes, as the self-supported hollow fiber membrane can eliminate the deformation-enhanced reverse salt diffusion that is typical for flat-sheet membranes. However it was observed that the water permeability and structure parameter of the TFC hollow fiber membrane varied noticeably corresponding to the change in the hydraulic pressure imposed in the fiber lumen. Over a certain range (ΔP<15bar), such variations of increasing A value and decreasing S value proved to have positive impacts, as they facilitate the water permeation and reduce the ICP in the PRO process. [Copyright &y& Elsevier]

Highlights: [•] Silver nanoparticles were deposited on MWNTs by chemical deposition method. [•] Ag/MWNTs were coated on the surface of UF PAN hollow fiber by physical method. [•] The antibacterial properties of the coating were tested in continues mode. [•] The coating is regenerable after silver depletion. [ABSTRACT FROM AUTHOR]

Abstract: A new type of forward osmosis (FO) hollow fiber membranes with an antifouling nanofiltration (NF)-like selective layer has been developed in this work. The fabrication involves a step of porous poly(amide-imide) (PAI) ultrafiltration (UF) hollow fiber spinning via phase inversion, followed by simple polyelectrolyte post-treatments using positively charged polyethyleneimine (PEI) for cross-linking and negatively charged polystyrene sulfonate sodium salt (PSS) for deposition. The membranes are subsequently characterized by a series of standard protocols and evaluated in FO process. The PAI FO membranes possess a pure water permeability of 3.7–4.3Lm−2 h−1 bar−1 and Na2SO4 rejections up to 85% at 1bar. In the FO process, the membranes can achieve water flux of 17 and 12Lm−2 h−1 for active layer facing draw solution (AL-facing-DS) and active layer facing feed water (AL-facing-FW) configurations, respectively, using a 2000ppm Na2SO4 aqueous solution as the feed and 0.5M Na2SO4 as the draw solution. When the feed contained 1000ppm bovine serum albumin (BSA) and 2000ppm Na2SO4, a steady water flux of 11Lm−2 h−1 can be maintained using 0.5M Na2SO4 as the draw solution at ambient temperature of 23°C. The approach of making FO membranes developed in the present study offers the advantages of simple fabrication process, tailorable selective layer and promising membrane performance for protein-contained wastewater treatment by FO process. [Copyright &y& Elsevier]

Abstract: Hollow fiber membranes with a positively charged nanofiltration (NF)-like selective layer have been successfully fabricated by utilizing asymmetric microporous hollow fibers made of Torlon® polyamide–imide (PAI) material as the porous substrate followed by polyelectrolyte post-treatment using polyethyleneimine (PEI), which has not been reported previously. The reaction between PAI and PEI has been confirmed by experiments. The membrane structure and surface property are carefully tailored by adjusting polymer dope composition, spinning conditions and the post-treatment parameters. These membranes are, subsequently, characterized by a series of standard protocols in terms of membrane morphology, structure, permeability and salt rejection, and are applied in forward osmosis (FO) processes. The newly developed PAI hollow fiber membranes show a pure water permeability of 2.19–2.25L/m2 hbar and reasonable NaCl and MgCl2 rejections of 49% and 94% at 1bar, respectively. It is also found that in FO processes, when using 0.5M MgCl2 as a draw solution and DI water as the feed in the active layer facing feed water (AL-facing-FW) configuration at 23°C, the water fluxes of two PAI FO hollow fiber membranes are 8.36 and 9.74L/m2 h, respectively, and the J S /J V of the two membranes is smaller than 0.4g/L, which is lower than the data of 0.85g/L for commercial FO membrane from Hydration Technologies Inc. (HTI). Different from a neutral membrane, the positively charged FO membrane provides double electric repulsions to the salt transfer through the membrane in the AL-facing-FW configuration, leading to a reduction of salt penetration, while in the active layer facing draw solution (AL-facing-DS) configuration, the positive charges facilitate salt transportation. This study provides a simple and effective approach to make hollow fibers suitable for FO applications. [Copyright &y& Elsevier]

Abstract: Polyvinylidene fluoride-co-hexafluropropylene (PVDF-HFP) has received much attention recently as a promising membrane material for membrane contactor application. A systematic study has been carried out to investigate the effects of polyethylene glycol (PEG) with different molecular weights and different loadings as an additive on the fabrication of PVDF-HFP asymmetric microporous hollow fiber membranes. Moreover, the synergetic effects of coagulation temperature and the second additive (lithium chloride: LiCl) with PEG are also evaluated. Experiments revealed that the addition of PEG into the PVDF-HFP/NMP solution resulted in the system thermodynamically less stable in reaction with water, promoting rapid phase demixing in the phase inversion process. When the same 3wt% PEG was added into the dope solution, the dimension of finger-like macrovoids of the resultant membrane increased in parallel with the increase of PEG molecular weight from 200 to 600 and 6000kDa, and pure water permeability (PWP) also increased accordingly. An increase in PWP was also observed when PEG-200 loading in the dope solution was increased from 3 to 5 and 10wt%, corresponding to the morphology change of resultant membranes. As a synergetic effect of coagulation temperature with PEG, the finger-like pores occurred in the membrane at room temperature expanded to much larger macrovoids using 10°C water as the coagulant, and the big finger-like pores almost disappeared when the coagulation bath temperature was increased to 40°C because of delayed phase demixing. The big macrovoid size can also be suppressed by adding the second small molecule additive, LiCl, due to its strong interactions with NMP and PVDF-HFP to delay the dope precipitation. The irregular inner contour of the membrane can be eliminated by the increase of coagulation bath temperature to 40°C. The hollow fiber membrane made by a dope of PVDF-HFP/PEG-6000/LiCl/NMP (15/3/3/79 in weight) using 40°C water as the coagulant exhibited a high PWP of 117L/m2 hatm and reasonably good MWCO of 150kDa. An improvement has been made in the current work as compared to previous PVDF-HFP hollow fiber membranes reported in literatures. [Copyright &y& Elsevier]

This report demonstrates the fabrication of a composite hollow fiber membrane that efficiently recovers dissolved methane (dCH 4) from anaerobic wastewater treatment effluents via membrane contactor (MC) process. We first fabricated highly porous hollow fiber membranes (∼85% porosity) using polyvinylidene difluoride (PVDF). Then, we coated the whole structure (bulk), or lumen side of PVDF supports with polydimethylsiloxane (PDMS), a hydrophobic polymer possessing high gas permeability. The adjustment of the concentration of PDMS precursor mix could effectively serve for tuning the performance characteristics of MC membranes and helped suppress membrane wetting, a major performance-reducing factor. Despite their denser skin layers, the lumen-modified membranes demonstrated superior dCH 4 recovery flux. Mass transfer analyses have confirmed the importance of preserving bulk porosity while coating the membrane surfaces. The long-term performance tests performed using actual anaerobic effluents suggested that the PDMS coating did not accelerate fouling, such that the lumen-modified MC membranes showed an almost steady flux for 8 days with an anaerobic membrane bioreactor effluent. A high-strength effluent, obtained from an up-flow anaerobic sludge blanket reactor, induced faster fouling. However, we observed only a ∼20% flux decline in a 10-day operation. Thus, we propose that the designed PDMS-PVDF composite membranes are promising for industrial practices. Image 1 • We prepared PDMS-coated PVDF porous hollow fiber membranes for membrane contacting. • Both lumen- and bulk-modified PVDF membranes were successful in methane recovery. • Lumen-modified PDMS-PVDF membrane outperformed commercial PP and PDMS membranes. • Lumen-modified PVDF achieved long-term performance with actual anaerobic effluents. [ABSTRACT FROM AUTHOR]

In this study, the glutaraldehyde (GA) crosslinking was adopted in combination of layer-by-layer (LBL) polyelectrolyte deposition to develop a novel hollow fiber NF membrane with low-pressure water softening capability for synthesized hard water containing divalent counterion SO 4 2− . The challenges for the new membrane include (a) the presence of SO 4 2− in the feed water, which tends to deteriorate positively charged NF membrane retention to divalent ions; (b) high salinity feed water up to 10,000 ppm total dissolved salt (TDS); (c) 2 bar operating pressure that requires the membrane to have a good Mg 2+ /Na + selectivity and less mass transfer resistance in the substrate; and (d) better separation performance as compared with the state-of-the-art and commercial NF membranes. Based on the membrane characterization results, the possible structure of the deposited layers and the effect of GA crosslink was proposed. It was found that the crosslinking could tighten the membrane surface pores with increased hydrophilicity while the membrane surface charge was reduced. Therefore, mainly based on the size exclusion, the crosslinked LBL*1.5C membrane showed more than 10 LMH/bar permeability with above 95% rejection to each of 1000 ppm MgCl 2 , MgSO 4 and Na 2 SO 4 solution under 2 bar pressure. It was also proved to be more suitable for the low-pressure water softening application at 2 bar in all tested feed water with the presence of SO 4 2− and TDS up to 10,000 ppm in terms of both permeability and hardness removal efficiency when compared with commercial NF 270 and NF 90 membranes. [ABSTRACT FROM AUTHOR]

The layer-by-layer (LBL) polyelectrolyte deposited membranes have drawn increasing attention in various applications due to the ease of selective layer formation and their stability and versatility. In this study, the LBL deposition was performed at the inner surface of the polyethersulfone (PES) hollow fiber substrate to form composite nanofiltration (NF) membrane. The semi-dynamic deposition procedure was adopted with the aid of syringes. The newly developed inner deposited (id-LBL) membranes were then tested in NF and forward osmosis (FO) applications and the performance were compared with outer surface deposition as well as some literature data. The id-LBL membranes could not only withstand higher operating pressure but also possess superior hardness rejection especially in high concentration mixed salt solutions (more than 95% rejection to Mg 2+ and Ca 2+ in a 5000 ppm total dissolved salt (TDS) mixture under 4.8 bar). As for the FO process, with only two layer deposition, the id-LBL membranes also demonstrated significant performance improvement with increased water flux (up to 70 L/m 2 h using 0.5 M MgCl 2 as draw solution in active layer facing draw solution configuration) and reduced salt leakage (around 0.5 g/m 2 h using 1 M MgCl 2 draw solution in active layer facing feed water configuration). This study suggests that for hollow fiber substrate, the inner surface is more suitable for the formation of the selective layer via LBL deposition than the outer surface. [ABSTRACT FROM AUTHOR]

Abstract The combination of nonsolvent and thermally induced phase separation (N-TIPS) method has shown promising ability in harvesting the features from the nonsolvent induced phase separation (NIPS) and thermally induced phase separation (TIPS) processes for developing membranes with a tailorable surface pore structure. However, previous approaches have been subjected to either the formation of macrovoids or dense layer due to the dominant NIPS effect, or required sophisticated instruments and operation skills. In this work, a facile attempt was carried out to fabricate novel polyvinylidene fluoride (PVDF) hollow fiber membranes with tunable surface pore structure while maintaining the narrow pore size distribution and mechanical strength. A modified N-TIPS method was developed by using mixed diluents: dimethyl phthalate (DMP) as a water-immiscible poor solvent for TIPS process, and triethyl phosphate (TEP) as a water-miscible neutral solvent to bridge the TIPS and NIPS processes. To further control the membrane formation especially near the membrane surface, an amphiphilic additive Pluronic F127 was also added as a potential pore-former and surface hydrophilicity modifier. PVDF hollow fiber membranes with a highly porous structure and a narrow pore size distribution were successfully synthesized by using TEP and Pluronic F127 in the N-TIPS process. The mechanism of N-TIPS process was thoroughly discussed. The water permeability of the membrane increased significantly from 389 ± 30–922 ± 36 L m–2 h–1 bar–1, with overall porosity improved from 50 ± 2.2–69 ± 2.9%, and a mean pore size of ~ 0.18 µm. The membranes produced by N-TIPS method also exhibited a good tensile strength ranging from 5.6 ± 0.1–6.5 ± 0.2 MPa, showing a great potential for a broad range of water applications after further modifications. Besides, the formation of piezoelectric β-phase crystals of the PVDF membrane was observed when the mixed diluent was used, which sheds light on the possible applications of resultant membranes in electrochemical separation process. Highlights • PVDF hollow fiber membranes were developed via a modified N-TIPS method using mixed diluents together with Pluronic F127. • The NIPS effect could be induced at the outer surface with the co-occurrence of TIPS process along the bulk of membrane. • The surface pore structure of membrane could be tailored without the formation of mechanically weak macrovoids. • The prepared membranes possess a hydrophobic surface with good porosity, permeability and mechanical strength. [ABSTRACT FROM AUTHOR]

Polyvinylidene fluoride (PVDF)/polytetrafluoroethylene (PTFE) hollow fiber membranes were developed via thermally induced phase separation (TIPS) method for direct contact membrane distillation (DCMD). The effects of PTFE addition on the thermal behavior of the dope mixtures and membrane formation were investigated. It was found that the crystallization of PVDF was significantly enhanced with increased nucleation sites provided by PTFE particles, leading to promoted formation of smaller spherulites in a greater density. Furthermore, the improved uniformity and increased amount of cavity between the spherical crystallites coherently facilitated the formation of smaller pores ranging from 0.08 to 0.12 μm. With certain PTFE loading, the membranes exhibited improved porosity, water permeability and hydrophobicity as well as enhanced tensile strength of 9.4 ± 0.3 MPa. To examine the DCMD performance, the membranes were tested under various conditions using 3.5 wt% NaCl solution. A stable permeation flux of 28.3 kg m − 2 h − 1 at the feed temperature of 60 °C with 99.99% NaCl rejection for over 50 h of operation was achieved, which is comparable with similar type of PVDF membranes while the newly developed membrane exhibited better mechanical strength. This study suggests that the as-spun PVDF/PTFE hollow fiber membranes have potential for DCMD applications. [ABSTRACT FROM AUTHOR]

A synthetic hormone, 17α-ethynylestradiol (EE2), has received much attention due to its widespread occurrence and adverse effects on aquatic animals. The removal of EE2 from water has been very challenging mostly because of its low concentration in environmental waters. Here we report a simple and novel approach for concentrating EE2 through adsorption and elution using microporous polyethersulfone (PES) hollow fiber membrane in a cross-flow filtration system, which can be easily scalable for practical applications. Our results showed that microporous PES hollow fiber membrane has a high EE2 adsorption capability (∼100% from water containing 20 μg/L of EE2) and the adsorbed EE2 could be eluted using a small volume of 10% ethanol solution to achieve a recovery efficiency of 75.9 ± 8.5%. We further demonstrated that the PES hollow fiber membrane maintained ∼100% removal of EE2 throughout five cycles of adsorption and elution. Our results from molecular simulation suggest that the strong affinity between PES and EE2 is mainly attributed to the π- π interaction and the hydrogen bonding. This proof-of-concept demonstrates for the first time that PES hollow fiber membrane system can remove EE2 at low concentrations, and elute EE2 solutions at a much higher concentration over multiple cycles in a sustainable and environmentally-benign condition. [ABSTRACT FROM AUTHOR]

Pressure retarded osmosis (PRO) is a promising energy harvesting technique. However, when polymeric hollow fiber membrane is used for the PRO process, the mechanical strength of the membrane is a big concern. As hollow fiber membrane is self-supported and due to its polymeric nature, it may gradually deform over time under high pressure loading, or membrane “creeping” will occur. Current work is the first attempt to analyze the membrane creeping phenomenon of a novel thin film composite (TFC) hollow fiber. The membrane creeping was evaluated via nanoindentation by using atomic force microscope (AFM). A non-stop 200-hour PRO test and integrity check, which have not been reported previously, were carried out to investigate the membrane performance under various operating pressures. The results show that the membrane is able to produce a stable power density output of 19.2 W/m 2 at 15.0 bar, using 1.0 M NaCl as the draw solution and DI water as the feed water. Membrane creeping was observed when the applied pressure exceeded the safe operation limit (or the flux turning point, where the membrane flux started to increase with increasing applied pressure in the PRO mode), which caused an irreversible damage to the membranes. This study identified safe and optimum operation conditions of the laboratory-made PRO hollow fiber membrane to achieve the most favorable PRO performance. It provides guidance for practical applications of polymeric hollow fiber membranes in PRO process. [ABSTRACT FROM AUTHOR]

In this study, the self-assembly of rare-earth Anderson polyoxometalates (POMs) on the surfaces of imide polymeric hollow fiber membranes was designed for fabrication of novel POMs-functionalized interfacial composite membranes. The rare-earth Anderson POM ([Gd(H 2 O) 7 Cr(OH) 6 Mo 6 O 18 ] n ) nanoparticles with controllable size and distribution were successfully constructed. Experimental results revealed that the self-assembly was a surface-induced growth process. The silanol groups on the membrane surfaces generated by the (3-aminopropyl)trimethoxysilane pretreatment were essential for the self-assembly process because of the potential hydrogen bonding ( OH⋯POMs) and coordination bonding ( OH Gd) interactions. This work provided a simple but practical method not only for the fabrication of novel POMs-functionalized membranes, but also for the synthesis of POMs nanoarchitectures. In addition, the potential application of the as-prepared POMs-functionalized hollow fiber membranes in degradation of organic pollutant has also been explored. The idea of interfacial membrane contactor has been utilized for the catalytic wet air oxidation of phenol under mild conditions. A three-phase (gas/catalyst/liquid) interface was successfully built up, which enhanced the catalytic efficiency. It is anticipated that these novel POMs-functionalized membranes can promisingly be used as catalytic membrane contactors for wastewater treatment under mild conditions. [ABSTRACT FROM AUTHOR]

The use of nanotechnology in water separation membranes is a promising approach to alleviate the global water crisis. Graphene oxide (GO) with its unique water transport property has exhibited high potential for application in the water treatment processes. In this study, we have designed and fabricated a novel nanofiltration (NF)-like GO surface deposited poly(amide-imide)–polyethyleneimine (PAI–PEI) hollow fiber membrane. The PAI hollow fiber substrate was prepared by phase inversion and modified with PEI to obtain a positively charged membrane surface. The negatively charged GO nanosheets were then electrostatically immobilized onto the membrane surface via an instant dip-coating to form the NF-like selective layer. Our results have shown that the GO nanosheets serve as effective selective barriers and can achieve higher water permeability up to 86% without compromising membrane selectivity when used to substitute part of the PEI cross-linked selective layer. This is attributed to the smaller hydrodynamic resistance of GO nanosheets and their ability to effectively narrow the pore size distribution. Moreover, shortening of the membrane modification time and better mechanical properties of the GO modified membrane can be attained by avoiding excessive PEI cross-linking. The GO deposition also exhibits good stability when subjected to a backwashing pressure of 100,000 Pa and a cross-flow rate of 600 mL/min, which corresponds to a velocity of 14 cm/s and a Reynolds number of ~870. These results have demonstrated a high potential of using this GO modified hollow fiber membrane for large scale water softening applications. [ABSTRACT FROM AUTHOR]

Abstract: The layer-by-layer (LBL) polyelectrolyte deposition was applied on polyethersulfone (PES) hollow fiber ultrafiltration membrane to prepare nanofiltration (NF) membrane for low pressure water softening application for the first time. The effects of polyelectrolyte type and molecular weight (MW), deposited bilayer number, polyelectrolyte solution pH and supporting electrolyte concentration on the performance of resultant membranes were studied thoroughly. Experiments revealed that the pH of the polyelectrolyte solution and supporting electrolyte concentration presented the most notable effects. For weak poly-cations, Poly(ethylenimine) (PEI) and Poly(allylamine hydrochloride) (PAH), the solution pH affected the membrane performance significantly, and high water permeability and divalent cation rejection were obtained at optimum pH values. Using a low concentration of supporting electrolyte at underneath layers was proved to be an effective way to increase water permeability while maintaining high salt rejection. A salt water flux (SWP) of 12LMH/bar and 94% Mg2+ rejection was obtained by depositing only two bilayers of PSS/PAH polyelectrolytes on the PES substrate, while for the 3000ppm mixed salt solution, the water permeability was 11LMH/bar with Mg2+ and Ca2+ rejection as high as 90%. These promising results demonstrate that LBL technique is potentially applicable for preparing low-pressure water softening hollow fiber membranes. [Copyright &y& Elsevier]

Municipal solid waste (MSW) gasification is an attractive waste-to-energy (WTE) technology with promise for future solid waste management, owing to the production of syngas which can be used as an alternative energy resource. However, quality of produced syngas is not meeting expectation. One promising solution is to use oxygen-enriched gas (OEG) to elevate produced syngas quality but producing OEG is costly. Herein, we demonstrated an asymmetric defect-free hollow fiber membrane made up of Matrimid® 5218 polyimide for scaling-up to 2-inch membrane modules. Our modules have an effective surface area up to 2.6 m2 with a packing density of up to 44% to produce OEG of 45% O 2 purity. The 2-inch membrane module was integrated into a lab-scale gasification process to produce syngas using refuse derived fuel (RDF) generated from MSWs collected from the university campus. Prior to this, the lab-scale gasification was first optimized by tuning the gasification temperature, O 2 purity and equivalence ratio (ER). Then, MSW gasification using membrane-based OEG was carried out, and compared against air gasification and synthetic OEG of the same O 2 purity. Our results showed that, at O 2 purity of 45%, gasification temperature of 900 °C and ER of 0.15, the quality of produced syngas was elevated with a lower heating value (LHV) of 9.15 MJ/m3 and H 2 /CO ratio of 1.43, which was substantially higher than air gasification with LHV and H 2 /CO ratio reported at 5.38 MJ/m3 and 0.81, respectively. Gasification results for membrane-based OEG and synthetic OEG were also comparable, while process simulation evidence suggested that membrane-based separation was at least 2-fold less energy-intensive than cryogenic distillation and pressure swing adsorption. Overall, this proof-of-concept successfully demonstrates the viability and competitiveness of membrane process for producing OEG at medium O 2 purity (i.e. , 40–50%) to support MSW gasification for WTE conversion. [Display omitted] • Hollow fiber membrane modules with up to 2.6 m2 surface area were developed. • OEG with O 2 purity of c.a. 45% can be produced at close to 2 L/min flow rate. • Membrane-based OEG gasification produces syngas with 70% higher LHV as that of air gasification. • Membrane-based OEG produces syngas with comparable LHV as that of synthetic OEG. • Simulation shows that membrane separation is less energy-intensive for producing OEG of medium purity. [ABSTRACT FROM AUTHOR]