Search

Starting from calcium sulfate (gypsum) as fermentation byproduct of lactic acid production process, high-performance composites have been produced by melt-blending polylactide ( PLA) and β-anhydrite II ( AII) filler, i.e., calcium sulfate hemihydrate previously dried at 500 °C. Characterized by attractive properties due to good filler dispersion throughout the polyester matrix and favorable interactions between components, these composites are interesting for potential use as biodegradable rigid packaging. The effect of filler content and mean particle diameter on the barrier properties such as sorption and diffusion to water vapor has been examined and compared to unfilled PLA. Even without additional treatments, the presence of the filler introduced constraints on molecular mobility in the permeable phase of amorphous PLA and the amount of solvent absorbed appears lower in the highly filled composites. Surprisingly, for PLA-30% AII compositions, by addition of filler characterized by high mean particle diameter (e.g., 43 μm) the thermodynamic diffusion parameter, D0, decreased up to 2 orders of magnitude. The dimension of filler particles and their percentage in the continuous polymeric phase seem to be the most important parameters that determine the barrier properties of the PLA-AII composites to water vapor. [ABSTRACT FROM AUTHOR]

The present paper reports, for the first time, the successful fabrication of layered double hydroxide (Mg−Al LDH)-reinforced polycaprolactone (PCL) nanofibers by electrospinning. Either the LDH in carbonate form or an LDH organically modified with 12-hydroxydodecanoic acid (LDH-HA) were incorporated into PCL and electrospun using a voltage of 20 KV. The LDH-HA was prepared by an ionic exchange reaction from pristine LDH and encapsulated into PCL from acetone solutions at 15 wt %. The morphological analysis showed pure PCL fibers with an average diameter of 600 ± 50 nm, and this dimension was maintained in the fibers with LDH, with the inorganic component residing outside the fibers and not exfoliated. At variance, the fibers with the LDH-HA showed a significantly lower average diameter in the range of 350 ± 50 nm, indicating the improved electrospinnability of PCL. Moreover, the inorganic lamellae were exfoliated, as shown by X-rays and residing inside the nanofibers as demonstrated by energy dispersive X-ray spectroscopy analysis. The structural parameters, such as degradation temperature and crystallinity, were investigated for all the samples and correlated with the electrospinning process. [ABSTRACT FROM AUTHOR]

High energy ball milling (HEBM) was utilized, as an innovative process, to incorporate carbon nanotubes (CNTs) into a polyethylene (PE) matrix avoiding: high temperatures, solvents, ultrasonication, chemical modification of carbon nanotubes. Composites with 1, 2, 3, 5, and 10 wt % of carbon nanotubes were prepared. Films were obtained melting the powders in a hot press. Morphology and physical properties (thermal, mechanical, electrical properties) were evaluated. The used processing conditions allowed to obtain a satisfactory level of dispersion of CNTs into the PE matrix with a consequent improvement of the physical properties of the samples. The thermal degradation was significantly delayed already with 1–2% wt of CNTs. The mechanical properties resulted greatly improved for low filler content (up to 3% wt). The electrical measurements showed a percolation threshold in the range 1–3 wt % of CNTs. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 597–606, 2007 [ABSTRACT FROM AUTHOR]

In this paper we have studied the effect of increasing carbon multi-walled nanotube (CNT) concentration in composites of syndiotactic polypropylene (sPP) having the same crystalline form but different morphologies. The attention was focused on the form I of sPP with different degrees of perfection (in terms of percentages of chains in helical conformation, crystal dimensions and crystallinity) obtained using two different quenching temperatures from the melt, i.e. 25 and 100?°C. We observed a decreasing effect of the crystallization temperature on increasing the nanotube content up to the samples with 10% of CNT, that show a very similar structural organization independent of the undercooling. Only the amorphous phase turns out more relaxed in the samples crystallized at the highest temperature. Either the thermal or the mechanical properties are improved on increasing the CNT content in both series of samples. The electrical conductivity increases in a similar manner in both series of samples and between 1 and 3 wt% it shows a sizable step of about eight orders of magnitude, a phenomenon that can be regarded as the onset of a percolating structure for which charge transport may take place. [ABSTRACT FROM AUTHOR]