Search

• New algorithm was able to register with an accuracy of <1 mm (in-plane) and <2°. • The algorithm could not register all images successfully. • Semi-automatic or manual registration is still required to obtain good results. The accurate quantification of in-vivo tibio-femoral kinematics is essential for understanding joint functionality, but determination of the 3D pose of bones from 2D single-plane fluoroscopic images remains challenging. We aimed to evaluate the accuracy, reliability and repeatability of an intensity-based 2D/3D registration algorithm. The accuracy was evaluated using fluoroscopic images of 2 radiopaque bones in 18 different poses, compared against a gold-standard fiducial calibration device. In addition, 3 natural femora and 3 natural tibiae were used to examine registration reliability and repeatability. Both manual fitting and intensity-based registration exhibited a mean absolute error of <1 mm in-plane. Overall, intensity-based registration of the femoral bone model revealed significantly higher translational and rotational errors than manual fitting, while no statistical differences (except for y-axis translation) were found for the tibial bone model. The repeatability of 108 intensity-based registrations showed mean in-plane standard deviations of 0.23–0.56 mm, but out-of-plane position repeatability was lower (mean SD: femur 7.98 mm, tibia 6.96 mm). SDs for rotations averaged 0.77–2.52°. While the algorithm registered some images extremely well, other images clearly required manual intervention. When the algorithm registered the bones repeatably, it was also accurate, suggesting an approach that includes manual intervention could become practical for efficient and accurate registration. [ABSTRACT FROM AUTHOR]

Videofluoroscopy has been shown to provide essential information in the evaluation of the functionality of total knee arthroplasties. However, due to the limitation in the field of view, most systems can only assess knee kinematics during highly restricted movements. To avoid the limitations of a static image intensifier, a moving fluoroscope has been presented as a standalone system that allows tracking of the knee during multiple complete cycles of level- and downhill-walking, as well as stair descent, in combination with the synchronous assessment of ground reaction forces and whole body skin marker measurements. Here, we assess the ability of the system to keep the knee in the field of view of the image intensifier. By measuring ten total knee arthroplasty subjects, we demonstrate that it is possible to maintain the knee to within 1.8 ± 1.4 cm vertically and 4.0 ± 2.6 cm horizontally of the centre of the intensifier throughout full cycles of activities of daily living. Since control of the system is based on real-time feedback of a wire sensor, the system is not dependent on repeatable gait patterns, but is rather able to capture pathological motion patterns with low inter-trial repeatability. [ABSTRACT FROM AUTHOR]

Force plates are common assessment tools used in biomechanics to measure ground reaction forces during motion capture or strength exercises. While the accuracy of the resulting kinetic data is critical for accurate gait analysis, factors such as plate mounting are thought to influence the measured point of force application (PFA) of the ground reaction forces. The aim of this study was therefore to present an accurate in-situ PFA calibration method. In addition, the approach was evaluated by examining the required PFA corrections over a period of ten years, which included plate remounting and a change of foundation. The in-situ PFA calibration was performed on six plates by assessing the locations of up to 98 points of force application per plate using an instrumented pole. Application of the in-situ PFA calibration approach reduced the root mean square errors by up to approximately 60% compared to the manufacturers calculation. Correction coefficients were strongly dependent on the individual platform as well as the location of the applied force on the plate. Remounting of the plates altered the plate coefficient corrections considerably, while changes over time were notable but not as extensive. We therefore recommend that plates should be recalibrated after remounting, but also at least every 5 years, in order to ensure the preservation of an accurate PFA. [ABSTRACT FROM AUTHOR]

Background: The posterior cruciate ligament (PCL) is the strongest ligament of the knee, serving as one of the major passive stabilizers of the tibio-femoral joint. However, despite a number of experimental and modelling approaches to understand the kinematics and kinetics of the ligament, the normal loading conditions of the PCL and its functional bundles are still controversially discussed. Objectives: This study aimed to generate science-based evidence for understanding the functional loading of the PCL, including the anterolateral and posteromedial bundles, in the healthy knee joint through systematic review and statistical analysis of the literature. Data sources: MEDLINE, EMBASE and CENTRAL Eligibility criteria for selecting studies: Databases were searched for articles containing any numerical strain or force data on the healthy PCL and its functional bundles. Studied activities were as follows: passive flexion, flexion under 100N and 134N posterior tibial load, walking, stair ascent and descent, body-weight squatting and forward lunge. Method: Statistical analysis was performed on the reported load data, which was weighted according to the number of knees tested to extract average strain and force trends of the PCL and identify deviations from the norms. Results: From the 3577 articles retrieved by the initial electronic search, only 66 met all inclusion criteria. The results obtained by aggregating data reported in the eligible studies indicate that the loading patterns of the PCL vary with activity type, knee flexion angle, but importantly also the technique used for assessment. Moreover, different fibres of the PCL exhibit different strain patterns during knee flexion, with higher strain magnitudes reported in the anterolateral bundle. While during passive flexion the posteromedial bundle is either lax or very slightly elongated, it experiences higher strain levels during forward lunge and has a synergetic relationship with the anterolateral bundle. The strain patterns obtained for virtual fibres that connect the origin and insertion of the bundles in a straight line show similar trends to those of the real bundles but with different magnitudes. Conclusion: This review represents what is now the best available understanding of the biomechanics of the PCL, and may help to improve programs for injury prevention, diagnosis methods as well as reconstruction and rehabilitation techniques. [ABSTRACT FROM AUTHOR]

Soft tissue artefact affects the determination of skeletal kinematics. Thus, it is important to know the accuracy and limitations of kinematic parameters determined and modelled based on skin marker data. Here, the curvature angles, as well as the rotations of the lumbar and thoracic segments, of seven healthy subjects were determined in the sagittal plane using a skin marker set and compared to measurements taken in an open upright MRI scanner in order to understand the influence of soft tissue artefact at the back. The mean STA in the flexed compared to the extended positions were 10.2±6.1 mm (lumbar)/9.3±4.2 mm (thoracic) and 10.7±4.8 mm (lumbar)/9.2±4.9 mm (thoracic) respectively. A linear regression of the lumbar and thoracic curvatures between the marker-based measurements and MRI-based measurements resulted in coefficients of determination, R2, of 0.552 and 0.385 respectively. Skin marker measurements therefore allow for the assessment of changes in the lumbar and thoracic curvature angles, but the absolute values suffer from uncertainty. Nevertheless, this marker set appears to be suitable for quantifying lumbar and thoracic spinal changes between quasi-static whole body postural changes. [ABSTRACT FROM AUTHOR]

The article presents information on a study on the measurement of kinematics of the lower leg, trunk, and spine during squats. The study was conducted on a total of 30 players who performed unrestricted and restricted barbell squats. It was found that the subjects showed significantly increased in range of motion (ROM) for thoracic curvature during the restricted squats.

The success of kinematic analysis that relies on inertial measurement units (IMUs) heavily depends on the performance of the underlying algorithms. Quantifying the level of uncertainty associated with the models and approximations implemented within these algorithms, without the complication of soft-tissue artefact, is therefore critical. To this end, this study aimed to assess the rotational errors associated with controlled movements. Here, data of six total knee arthroplasty patients from a previously published fluoroscopy study were used to simulate realistic kinematics of daily activities using IMUs mounted to a six-degrees-of-freedom joint simulator. A model-based method involving extended Kalman filtering to derive rotational kinematics from inertial measurements was tested and compared against the ground truth simulator values. The algorithm demonstrated excellent accuracy (root-mean-square error ≤ 0.9 °, maximum absolute error ≤ 3.2 °) in estimating three-dimensional rotational knee kinematics during level walking. Although maximum absolute errors linked to stair descent and sit-to-stand-to-sit rose to 5.2° and 10.8°, respectively, root-mean-square errors peaked at 1.9° and 7.5°. This study hereby describes an accurate framework for evaluating the suitability of the underlying kinematic models and assumptions of an IMU-based motion analysis system, facilitating the future validation of analogous tools. [ABSTRACT FROM AUTHOR]

Abstract: Background: Gait analysis is an important instrument in clinical research and results should be objective. The purpose of this study was to quantify clinical outcomes of two biomechanical models with different anatomical coordinate systems and angle decomposition strategies for knee joint kinematics. Methods: The study was designed to compare a functional approach and a predictive approach with a single comprehensive marker set. 10 healthy subjects and 12 subjects with knee osteoarthritis were analysed. Distinctive gait variables were averaged across five trials. Agreement between methods was illustrated with the so-called levels of agreement. Differences between models were quantified using a paired t-test or Wilcoxon-Signed Rank test in case of non-normality (Shapiro–Wilk test). Unpaired t-tests/Wilcoxon tests were used to compare gait variables between healthy subjects and subjects with knee osteoarthritis, and to examine whether statistical analysis of this comparison would yield different data interpretations when using different models. Findings: Outcome variables differed between the functional and predictive approaches in the sagittal plane (0.1–3.1°), and transverse plane (1.0–3.7°). With respect to the range of motion in the given movement plane, variables in the sagittal plane of the knee were more consistent between methods. The functional approach was more sensitive for detecting differences between groups for sagittal plane kinematics. Statistical analysis for transverse plane kinematics differed substantially between models. Interpretation: Sensitivity to detect differences of kinematic data between population groups can vary between biomechanical models. Rotational gait variables are inconsistent between models and should not be used as clinical outcome variables in daily routine. [Copyright &y& Elsevier]

Gait analysis is an important instrument to investigate foot and ankle biomechanics in the field of footwear design. Results of this method should be objective and comparable. The purpose of this study was to compare two different approaches to quantify ankle joint kinematics: Functionally determined joint centres/axes (FA) versus a predictive model (PA). A single comprehensive marker set was defined. Twenty-two subjects were analysed, and distinctive gait variables were averaged across five trials. Agreement between methods was quantified according to Bland & Altman (Bland and Altman 1986. Lancet, i (8476), 307). Outcome variables differed remarkably between FA and PA at the talocrural (2-9°) and subtalar joints (1-6°). Considerable differences between variables describing motion of the ankle joint complex were primarily related to the use of different rotational axes and definitions of foot segments. This should be considered when studies using different foot models are compared. [ABSTRACT FROM AUTHOR]

An abstract of the article "How Well Can Skin Marker Analysis Detect the Kinematics of a Total Ankle Arthroplasty? - A Comparison to Videofluoroscopy," by Renate List, Hans Gerber, Mauro Foresti, Silvio Lorenzetti, Pascal Rippstein, and Edgar Stüssi is presented.

Background: Instrumented treadmills are potentially useful tools for the assessment of gait parameters in orthopaedic clinical settings, but their measurement properties remain uncertain.Research Question: What is the discriminant validity and reproducibility of spatiotemporal and kinetic gait parameters measured by a pressure-instrumented treadmill at different speeds and inclinations in patients with knee osteoarthritis (KOA)?Methods: A total of 54 patients with unilateral KOA and 23 healthy controls took part in the study. Step length, single-limb support duration and ground reaction force were recorded during level and uphill walking at 3 and 4 km/h using a commercially-available treadmill instrumented with an integrated pressure platform. We examined discriminant validity (difference between involved and uninvolved side as well as against healthy controls) and test-retest reproducibility (reliability and agreement).Results: Significant side differences were observed for single-limb support duration and ground reaction force at touchdown in all conditions (P < 0.05). All the investigated gait parameters showed acceptable reliability and agreement, except step length at 4 km/h uphill.Significance: We conclude that the pressure-instrumented treadmill used in this study may have good clinical utility for quantitative gait analysis in patients with KOA under different experimental conditions. [ABSTRACT FROM AUTHOR]

A comparison of natural versus replaced tibio-femoral kinematics in vivo during challenging activities of daily living can help provide a detailed understanding of the mechanisms leading to unsatisfactory results and lay the foundations for personalised implant selection and surgical implantation, but also enhance further development of implant designs towards restoring physiological knee function. The aim of this study was to directly compare in vivo tibio-femoral kinematics in natural versus replaced knees throughout complete cycles of different gait activities using dynamic videofluoroscopy. Twenty-seven healthy and 30 total knee replacement subjects (GMK Sphere, GMK PS, GMK UC) were assessed during multiple complete gait cycles of level walking, downhill walking, and stair descent using dynamic videofluoroscopy. Following 2D/3D registration, tibio-femoral rotations, condylar antero-posterior translations, and the location of the centre of rotation were compared. The total knee replacement groups predominantly experienced reduced tibial internal/external rotation and altered medial and lateral condylar antero-posterior translations compared to natural knees. An average medial centre of rotation was found for the natural and GMK sphere groups in all three activities, whereas the GMK PS and UC groups experienced a more central to lateral centre of rotation. Each total knee replacement design exhibited characteristic motion patterns, with the GMK Sphere most closely replicating the medial centre of rotation found for natural knees. Despite substantial similarities between the subject groups, none of the implant geometries was able to replicate all aspects of natural tibio-femoral kinematics, indicating that different implant geometries might best address individual functional needs. • Each total knee replacement design exhibited characteristic motion patterns. • GMK Sphere closest replicated the medial centre of rotation found in natural knees. • No implant was able to replicate all aspects of natural tibio-femoral kinematics. [ABSTRACT FROM AUTHOR]

Measuring joint kinematics is a key requirement for a plethora of biomechanical research and applications. While x-ray based systems avoid the soft-tissue artefacts arising in skin-based measurement systems, extracting the object's pose (translation and rotation) from the x-ray images is a time-consuming and expensive task. Based on about 106'000 annotated images of knee implants, collected over the last decade with our moving fluoroscope during activities of daily living, we trained a deep-learning model to automatically estimate the 6D poses for the femoral and tibial implant components. By pretraining a single stage of our architecture using renderings of the implant geometries, our approach offers personalised predictions of the implant poses, even for unseen subjects. Our approach predicted the pose of both implant components better than about 0.75 mm (in-plane translation), 25 mm (out-of-plane translation), and 2° (all Euler-angle rotations) over 50% of the test samples. When evaluating over 90% of test samples, which included heavy occlusions and low contrast images, translation performance was better than 1.5 mm (in-plane) and 30 mm (out-of-plane), while rotations were predicted better than 3−4°. Importantly, this approach now allows for pose estimation in a fully automated manner. [ABSTRACT FROM AUTHOR]

Abstract: Before making interpretations on the effects of interventions or on the features of pathological gait patterns during stair ambulation, the day-to-day consistency of the investigated variables must be established. In this article, the day-to-day consistency was determined for kinematic variables during barefoot stair ambulation. Ten healthy athletes performed two gait analysis sessions, at least one week apart, utilizing a marker set of 47 skin markers, and a functional joint center/axes determination. Being found on limits of agreement and mean differences between the repeated stair ambulation sessions, totally 43 ranges of motions were examined at the hip, knee, ankle, and midfoot joints. The day-to-day consistency was generally in the magnitude of three degrees, irrespective of test condition, investigated joint, or regarded cardinal body plane. The reported values of the day-to-day consistency provide guidelines to distinguish between pathological and healthy gait patterns, and thresholds to determine minimal effects of interventions during stair ambulation. [Copyright &y& Elsevier]

Purpose: Unicompartmental knee arthroplasty (UKA), resulting in similar kinematics to native knees, is functionally superior to total knee arthroplasty (TKA). However, ACL deficiency is generally considered to be a contraindication. The main purpose of this study was to investigate if UKA in ACL-deficient knees would result in similar kinematics to conventional UKA with an intact ACL.Methods: Ten conventional UKA patients were compared to eight ACL-deficient patients with a reduced tibial slope to compensate for instability, resulting from the deficient ACL. Knee kinematics was evaluated with a moving fluoroscope, tracking the knee joint during daily activities. In a standing position (baseline), posterior shift of the femur was observed for ACL-deficient UKA patients, compared to conventional UKA patients.Results: A significant posterior femoral shift in the ACL-deficient group was observed during the first 25% (near extension) of deep knee bend, while there was no difference in kinematic waveforms for all other activities. No significant range of motion differences across different activities between the two UKA groups were detected, except for an increase of medial AP translation in the ACL-deficient group, during deep knee bend and stair descent.Conclusion: Despite the posterior femoral shift due to ACL deficiency, both UKA groups showed similar kinematic waveforms, indicating that posterior tibial slope reduction can partially compensate for ACL function. This supported our hypothesis that fixed bearing UKA can be a viable treatment option for selected ACL-deficient patients, allowing patient-specific kinematics. While anteroposterior laxity can be compensated, rotational stability was a prerequisite for this approach.Level Of Evidence: III. [ABSTRACT FROM AUTHOR]

This research assessed the influence of various heel elevation conditions on spinal kinematic and kinetic data during loaded (25% and 50% of body weight) high-bar back squats. Ten novice (mass 67.6 ± 12.4 kg, height 1.73 ± 0.10 m) and ten regular weight trainers (mass 66.0 ± 10.7 kg, height 1.71 ± 0.09 m) completed eight repetitions at each load wearing conventional training shoes standing on the flat level floor (LF) and on an inclined board (EH). The regular weight training group performed an additional eight repetitions wearing weightlifting shoes (WS). Statistical parametric mapping (SPM1D) and repeated measures analysis of variance were used to assess differences in spinal curvature and kinetics across the shoe/floor conditions and loads. SPM1D analyses indicated that during the LF condition the novice weight trainers had greater moments around L4/L5 than the regular weight trainers during the last 20% of the lift (P < 0.05), with this difference becoming non-significant during the EH condition. This study indicates that from a perspective of spinal safety, it appears advantageous for novice weight trainers to perform back squats with their heels slightly elevated, while regular weight trainers appear to realize only limited benefits performing back squats with either EH or WS. [ABSTRACT FROM AUTHOR]

Joint stability is a primary concern in total knee joint replacement. The GMK Sphere prosthesis was specifically designed to provide medial compartment anterior–posterior (A–P) stability, while permitting rotational freedom of the joint through a flat lateral tibial surface. The objective of this study was to establish the changes in joint kinematics introduced by the GMK Sphere prosthesis during gait activities in comparison to conventional posterior‐stabilized (PS) fixed‐bearing and ultra‐congruent (UC) mobile‐bearing geometries. The A–P translation and internal/external rotation of three cohorts, each with 10 good outcome subjects (2.9 ± 1.6 years postop), with a GMK Sphere, GMK PS or GMK UC implant were analysed throughout complete cycles of gait activities using dynamic videofluoroscopy. The GMK Sphere showed the smallest range of medial compartment A–P translation for level walking, downhill walking, and stair descent (3.6 ± 0.9 mm, 3.1 ± 0.8 mm, 3.9 ± 1.3 mm), followed by the GMK UC (5.7 ± 1.0 mm, 8.0 ± 1.7 mm, 8.7 ± 1.9 mm) and the GMK PS (10.3 ± 2.2 mm, 10.1 ± 2.6 mm, 11.6 ± 1.6 mm) geometries. The GMK Sphere exhibited the largest range of lateral compartment A–P translation (12.1 ± 2.2 mm), and the largest range of tibial internal/external rotation (13.2 ± 2.2°), both during stair descent. This study has shown that the GMK Sphere clearly restricts A–P motion of the medial condyle during gait activities while still allowing a large range of axial rotation. The additional comparison against the conventional GMK PS and UC geometries, not only demonstrates that implant geometry is a key factor in governing tibio‐femoral kinematics, but also that the geometry itself probably plays a more dominant role for joint movement than the type of gait activity. © 2019 The Authors. Journal of Orthopaedic Research® published by Wiley Periodicals, Inc. on behalf of Orthopaedic Research Society. J Orthop Res 37:2337–2347, 2019 [ABSTRACT FROM AUTHOR]

Background: The measurement of finger and wrist range of motion (ROM) is of great importance to clinicians when assessing functional outcomes of therapeutic interventions and surgical procedures. The purpose of the study was to assess the repeatability of ROM measurements of the hand joints with manual goniometer and 3D motion capture system and to calculate the minimal detectable difference for both methods. Methods: Active finger and wrist joints ROM of 20 healthy volunteers were assessed using a manual goniometer and 3D motion capture system. Minimal detectable difference (MDD) and standard error of measurement (SEM) were calculated for both measurement systems and compared within the same task. Maximal ROM of all joints was registered twice on two different days to evaluate the test-retest repeatability. The intraclass correlation coefficients (ICC) was calculated and examined to determine if reliability ≥ 0.70 existed. Results: MDD for the 3D motion capture was between 5 and 12° except for the metacarpophalangeal joint (MCP) 1, interphalangeal joint (IP), and MCP5. SEM values lay between 2 and 4° for all joints except for the MCP5, IP, and MCP1. For the goniometric measurements, MDD and SEM were between 12–30° and 4–11°, respectively. The reliability criterion (ICC > 0.7) was achieved for the ROM measurement with the 3D motion capture system for 94% of the joints and in only 65% of the joints with the manual goniometer. Conclusions: Joint ROM assessed with 3D motion analysis showed higher test-retest agreement demonstrating overall better repeatability for this method. Because of the smaller measurement error, the 3D motion capture system has a smaller MDD. Only individual test-rest differences bigger than the MDD can be considered as real changes, and therefore, in an experimental situation, the use of a more precise measurement method can greatly reduce the number of subjects needed for a statistical significance. Goniometer measurements of some joints should be carefully interpreted, due to a low repeatability and reliability. Trial registration: This study is approved by the Ethical Committee Zurich (Kek-ZH-Nr: 2015-0395). [ABSTRACT FROM AUTHOR]

Background: Prevalence of knee osteoarthritis increases because life expectancy continues to rise with an active patient population. Hence, the concept of unicompartmental knee arthroplasty (UKA) has regained popularity as a treatment option for unicompartmental knee osteoarthritis. Anterior cruciate ligament (ACL) deficiency is widely considered as a contraindication for UKA, however, there are conflicting reports. If otherwise indicated, some surgeons consider UKA for ACL-deficient patients using a modified surgical technique, with a reduction of posterior tibial slope.Research Question: The purpose of this study was to evaluate outcomes in UKA patients with ACL deficiency in comparison to a conventional UKA group (intact ACL) by the measurement of knee kinematics and kinetics.Methods: Ten patients with conventional UKA and an intact ACL and eight patients with an ACL-deficient UKA and a reduced posterior tibial slope relative to the native knee were recruited. Three-dimensional joint kinematics of the knee were measured, using skin markers and an infrared optical motion capture system. Ground reaction forces (GRF) were measured with force plates in all three directions. Level walking, ramp descent and stair descent were analyzed, comparing implanted and contralateral native knees and the two UKA groups.Results: No significant differences in kinetics and kinematics were observed between conventional UKA and ACL-deficient UKA groups for any of the activities. However, some asymmetries in GRF between the implanted and contralateral side were present for the ACL-deficient group, during level walking (unloading rate) and stair descent (stance time).Significance: Promising outcomes of the ACL-deficient UKA group suggest that ACL deficiency may not always be a contraindication. Therefore, ACL-deficient UKA could be an alternative treatment option to total knee arthroplasty for an appropriate surgeon selected patient population. [ABSTRACT FROM AUTHOR]

Background: Regular infant carrying might be a contributing factor for the development and progression of low back and pelvic girdle pain in mothers after childbirth. However, the neuromechanical adaptations of the spine due to different sling-based carrying techniques are not sufficiently well understood in order to provide evidence-based carrying recommendations.Research Question: What are the immediate effects of different sling-based infant carrying techniques on trunk neuromechanics?Methods: Using a Vicon motion capture and a wireless surface electromyography system, three-dimensional pelvis and spinal kinematics as well as activation patterns of eight trunk muscles were derived from fifteen healthy young women during upright standing and level walking without carrying a load and while carrying a 6 kg-dummy with a sling in front and on either side. Data were analyzed using Statistical Parametric Mapping, allowing group comparisons of discrete parameters (standing) as well as continuous data (walking). To distinguish between clinically relevant and clinically not relevant kinematic findings, statistically significant differences were only considered in case of ≥5°.Results: Compared to unloaded walking, carrying the dummy in front was mainly associated with increased lumbar lordosis (standing: (Δ8.8°, p = 0.006; walking: (Δ ≥ 8.2°, 1-100% of gait cycle [%GC], p < 0.001). When carrying the dummy on the preferred side, increased thoracic kyphosis (standing: ≥6.4°, p ≤ 0.003; walking: Δ ≥ 5.6°, 1-100%GC, p < 0.001) and axial rotation towards the ipsilateral side (standing: Δ5.3°, p = 0.003; walking: Δ ≥ 5.0°, 46-58%GC, p = 0.002) were observed. All three conditions entailed increased paraspinal muscle activity during walking, although only unilaterally in side carrying (lumbar, preferred condition: Δ ≥ 13.2%maxMVIC, 49-57%GC, p < 0.001; thoracic, non-preferred condition: Δ ≥ 5.3%maxMVIC, 47-58%GC, p < 0.001).Significance: Carrying an infant alternating on both sides using a sling could be advantageous for preventing musculoskeletal pain resulting from excessive lumbar hyperextension and paraspinal muscle hyperactivation in women after childbirth. [ABSTRACT FROM AUTHOR]

Highlights • An average joint contact force prediction error of less than 20% was achieved at 25°–60° knee flexion during squats. • The average JCF error behaved almost linearly with knee flexion angle. • At deep flexion, an overestimation of approximately 60% JCF was observed. • Our data indicate that loading estimations from early musculoskeletal gait models at both high and low knee joint flexion angles should be interpreted carefully. • Validation of models was performed against state-of-the-art CAMS-Knee datasets. Abstract Standard musculoskeletal simulation tools now offer widespread access to internal loading conditions for use in improving rehabilitation concepts or training programmes. However, despite broad reliance on their outcome, the accuracy of such loading estimations, specifically in deep knee flexion, remains generally unknown. The aim of this study was to evaluate the error of tibio-femoral joint contact force (JCF) calculations using musculoskeletal simulation compared to in vivo measured JCFs in subjects with instrumented total knee endoprostheses during squat exercises. Using the early but common "Gait2392_simbody" (OpenSim) scaled musculoskeletal models, tibio-femoral JCFs were calculated in 6 subjects for 5 repetitions of squats. Tibio-femoral JCFs of 0.8–3.2 times bodyweight (BW) were measured. While the musculoskeletal simulations underestimated the measured knee JCFs at low flexion angles, an average error of less than 20% was achieved between approximately 25°–60° knee flexion. With an average error that behaved almost linearly with knee flexion angle, an overestimation of approximately 60% was observed at deep flexion (ca. 80°), with an absolute maximum error of ca. 1.9BW. Our data indicate that loading estimations from early musculoskeletal gait models at both high and low knee joint flexion angles should be interpreted carefully. [ABSTRACT FROM AUTHOR]

Video-fluoroscopic analysis can provide important insights for the evaluation of outcome and functionality after total knee arthroplasty, allowing the in vivo assessment of tibiofemoral kinematics without soft tissue artefacts. To enable measurement of the knee throughout activities of daily living such as gait, robotic systems like the moving fluoroscope have been developed that follow the knee movement and maintain the joint in front of the image intensifier. Since it is unclear whether walking while being accompanied by moving fluoroscope affects normal gait, the objective of this study was to investigate its influence on gait characteristics in healthy subjects. In addition, the impact of the motors’ noise was analysed. By means of skin markers analysis (VICON MX system, Oxford Metrics Group, UK) and simultaneous measurement of ground reaction forces (Kistler force plates, Kistler, Switzerland), gait characteristics when walking with and without the moving fluoroscope as well as with and without ear protectors in combination with the moving fluoroscope, were obtained in young (n = 10, 24.5y ± 3.0y) and elderly (n = 9, 61.6y ± 5.3y) subjects during level gait and stair descent. Walking with the moving fluoroscope significantly decreased gait velocity in level gait and stair descent over the respective movement without the fluoroscope. Statistical analysis, including gait velocity as a covariate, resulted in no differences on the ground reaction force parameters. However, some kinematic parameters (ankle, knee and hip ranges of motion, minimal knee angle in late stance phase, maximal knee angles in stance and swing phase) seemed to be modified by the presence of the moving fluoroscope, but statistical comparison was limited due to velocity differences between the conditions. Wearing ear protectors to avoid the influence of motor sound during walking with the moving fluoroscope caused no significant difference. Walking with the moving fluoroscope has been shown to decrease gait velocity and small alterations in kinematic parameters were observed. Therefore, gait and movement alterations due to the moving fluoroscope cannot completely be excluded. However, based on the absence of differences in ground reaction force parameters (when adjusted for velocity within ANCOVA), as well as based on the comparable shape of the angular curves to the slow control condition, it can be concluded that changes in gait when walking with the moving fluoroscope are small, especially in comparison to natural slow walking. In order to allow assessment of joint replacement with the moving fluoroscope, including an understanding of the effects of joint pain, clinical analyses can only be compared to gait activities showing similarly reduced velocities. Importantly, the reduced gait speeds observed in this study are similar to those observed after total knee arthroplasty, suggesting that analyses in such subjects are appropriate. However, the moving fluoroscope would likely need to be optimized in order to detect natural gait characteristics at the higher gait velocities of healthy young subjects. The moving fluoroscope can be applied for comparisons between groups measured with the moving fluoroscope, but care should be taken when comparing data to subjects walking at self-selected speed without the moving fluoroscope. [ABSTRACT FROM AUTHOR]

Combined knowledge of the functional kinematics and kinetics of the human body is critical for understanding a wide range of biomechanical processes including musculoskeletal adaptation, injury mechanics, and orthopaedic treatment outcome, but also for validation of musculoskeletal models. Until now, however, no datasets that include internal loading conditions (kinetics), synchronized with advanced kinematic analyses in multiple subjects have been available. Our goal was to provide such datasets and thereby foster a new understanding of how in vivo knee joint movement and contact forces are interlinked – and thereby impact biomechanical interpretation of any new knee replacement design. In this collaborative study, we have created unique kinematic and kinetic datasets of the lower limb musculoskeletal system for worldwide dissemination by assessing a unique cohort of 6 subjects with instrumented knee implants (Charité – Universitätsmedizin Berlin) synchronized with a moving fluoroscope (ETH Zürich) and other measurement techniques (including whole body kinematics, ground reaction forces, video data, and electromyography data) for multiple complete cycles of 5 activities of daily living. Maximal tibio-femoral joint contact forces during walking (mean peak 2.74 BW), sit-to-stand (2.73 BW), stand-to-sit (2.57 BW), squats (2.64 BW), stair descent (3.38 BW), and ramp descent (3.39 BW) were observed. Internal rotation of the tibia ranged from 3° external to 9.3° internal. The greatest range of anterio-posterior translation was measured during stair descent (medial 9.3 ± 1.0 mm, lateral 7.5 ± 1.6 mm), and the lowest during stand-to-sit (medial 4.5 ± 1.1 mm, lateral 3.7 ± 1.4 mm). The complete and comprehensive datasets will soon be made available online for public use in biomechanical and orthopaedic research and development. [ABSTRACT FROM AUTHOR]

The purpose of this study was to measure alterations in sensorimotor skills and balance resulting from slackline training and conventional balance training. Forty-three physically fit subjects were randomized into three groups. Two groups practiced three times a week for 15 minutes, including at least once supervised session, on the slackline or perform conventional balance training for 6 weeks. The control group was not allowed to perform any balance training. Before and after the intervention, the subjects underwent sensorimotor and strength tests. The results of our intra-class correlation analysis showed that the stability parameters from the multifunctional training device (MFT, 0.7), the height during the countermovement jump (CMJ, 0.95) and the maximum force (0.88) during leg press showed excellent reliability. A post hoc comparison indicated a larger effect of conventional training (almost 11% reduction in MFT stability) compared with slackline training in group-wide comparisons of the pre- to the post-training measurements. The factor analysis showed that stability and sensorimotor assessment using MFT were correlated, as were height during CMJ and maximal force during leg press, which represented dynamic strength. Because CMJ had the highest intra-class correlation value, it was chosen over maximum force from leg press. For these reasons, only two out of nine measured parameters, namely MFT stability and CMJ, were analysed across groups. The only observed difference between the two groups was MFT stability (slackline - 1.5%, conventional - 13%), whereas the improvement of CMJ was the same (slackline + 3%, conventional + 3%). It can be concluded that slacklining is partly complementary to conventional sensorimotor training. [ABSTRACT FROM AUTHOR]

Background: The goal of this review is to summarise and discuss the reported influence of muscle-tendon forces on anterior cruciate ligament (ACL) loading during the jump-landing task by means of biomechanical analyses of the healthy knee. Methods: A systematic review of the literature was conducted using different combinations of the terms "knee", "ligament'', "load'', "tension ", "length", "strain'', "elongation'' and "lengthening''. 26 original articles (n=16 in vitro studies; n=10 in situ studies) were identified which complied with all inclusion/exclusion criteria. Results: No apparent trend was found between ACL loading and the ratio between hamstrings and quadriceps muscle-tendon forces prior to or during landing. Four in vitro studies reported reduced peak ACL strain if the quadriceps force was increased; while one in vitro study and one in situ study reported reduced ACL loading if the hamstrings force was increased. A meta-analysis of the reported results was not possible because of the heterogeneity of the confounding factors. Conclusion: The reported results suggest that increased hip flexion during landing may help in reducing ACL strain by lengthening the hamstrings, and thus increasing its passive resistance to stretch. Furthermore, it appears that increased tensile stiffness of the quadriceps may help in stabilising the knee joint during landing, and thus protecting the passive soft-tissue structures from overloading. Level of evidence: Ib. [ABSTRACT FROM AUTHOR]

ABSTRACT Understanding the mechanical loading environment and resulting joint mechanics for activities of daily living in total knee arthroplasty is essential to continuous improvement in implant design. Although survivorship of these devices is good, a substantial number of patients report dissatisfaction with the outcome of their procedure. Knowledge of in vivo kinematics and joint loading will enable improvement in preclinical assessment and refinement of implant geometry. The purpose of this investigation was to describe the mechanics of total knee arthroplasty during a variety of activities of daily living (gait, walking down stairs, and chair rise/sit). Estimates of muscle forces, tibial contact load, location, and pressure distribution was performed through a combination of mobile fluoroscopy data collection, musculoskeletal modeling, and finite element simulation. For the activities evaluated, joint compressive load was greatest during walking down stairs; however, the highest contact pressure occurred during chair rise/sit. The joint contact moment in the frontal plane was mainly varus for gait and walking down stairs, while it was valgus during chair rise/sit. Excursion of the center of pressure on the tibial component was similar during each activity and between the medial and lateral sides. The main determinants of center of pressure location were internal-external rotation, joint load, and tibial insert conformity. © 2016 Orthopaedic Research Society. Published by Wiley Periodicals, Inc. J Orthop Res 34:1576-1587, 2016. [ABSTRACT FROM AUTHOR]

While there is general agreement on the transverse plane knee joint motion for loaded flexion activities, its kinematics during functional movements such as level walking are discussed more controversially. One possible cause of this controversy could originate from the interpretation of kinematics based on different analysis approaches. In order to understand the impact of these approaches on the interpretation of tibio-femoral motion, a set of dynamic videofluoroscopy data presenting continuous knee bending and complete cycles of walking in ten subjects was analysed using six different kinematic analysis approaches. Use of a functional flexion axis resulted in significantly smaller ranges of condylar translation compared to anatomical axes and contact approaches. All contact points were located significantly more anteriorly than the femur fixed axes after 70° of flexion, but also during the early/mid stance and late swing phases of walking. Overall, a central to medial transverse plane centre of rotation was found for both activities using all six kinematic analysis approaches, although individual subjects exhibited lateral centres of rotation using certain approaches. The results of this study clearly show that deviations from the true functional axis of rotation result in kinematic crosstalk, suggesting that functional axes should be reported in preference to anatomical axes. Contact approaches, on the other hand, can present additional information on the local tibio-femoral contact conditions. To allow a more standardised comparison and interpretation of tibio-femoral kinematics, results should therefore be reported using at least a functionally determined axis and possibly also a contact point approach. [ABSTRACT FROM AUTHOR]

The article reports on research conducted to compare the angles and corresponding moments in the knee and hip during restricted and unrestricted squats. Researchers evaluated 20 subjects who performed both types of squats. They found that during the unrestricted squats, the maximum moments in the knee were significantly higher, and those in the hip were significantly lower than during restricted squats and that athletes seeking to strengthen their quadriceps should use unrestricted squats.

Abstract: The goal of this study was to compare selected parameters of vertical ground reaction forces (GRF) of good outcome patients with different prosthesis designs with a matched control group during level walking, stair ascent and descent. Forty subjects, 29 with three main implant designs (including four subjects with a passive knee flexion restriction), and 11 healthy controls were measured with 8–10 repetitions. Vertical ground reaction forces were measured during two consecutive steps with force plates embedded in the walkway and the staircase. Defined parameters of the force signals were used to compare the results of the test groups. The results show, that, postoperatively, good outcome patients produce gait patterns of the vertical ground reaction force which are comparable to normal healthy subjects with the exception of a few distinct differences: a significant reduction (p <0.05) in the vertical loading on the operated side during level walking at take-off, at weight acceptance and take-off during stair ascent of the normal stair. During stair descent, the patients did not reduce load on the operated side, but increased load variation and side-to-side asymmetry; thus, the mechanical loads on the implants were high, which may be important information with respect to loading protocols of knee implant simulators. No systematic differences in any of the test parameters were found between posterior cruciate-retaining (LCS MB and Innex CR) versus non-retaining (LCS RP and Innex UCOR) implant designs. The restricted group showed significant reductions (p <0.05) of several loading parameters as well as an increased side-to-side asymmetry. About one third of the force parameters of the good outcome patients showed a side-to-side asymmetry between two consecutive steps, which was over a proposed level of acceptance. [Copyright &y& Elsevier]

Accurate assessment of 3D tibio-femoral kinematics is essential for understanding knee joint functionality, but also provides a basis for assessing joint pathologies and the efficacy of musculoskeletal interventions. Until now, however, the assessment of functional kinematics in healthy knees has been mostly restricted to the loaded stance phase of gait, and level walking only, but the most critical conditions for the surrounding soft tissues are known to occur during high-flexion activities. This study aimed to determine the ranges of tibio-femoral rotation and condylar translation as well as provide evidence on the location of the centre of rotation during multiple complete cycles of different gait activities. Based on radiographic images captured using moving fluoroscopy in ten healthy subjects during multiple cycles of level walking, downhill walking and stair descent, 3D femoral and tibial poses were reconstructed to provide a comprehensive description of tibio-femoral kinematics. Despite a significant increase in joint flexion, the condylar antero-posterior range of motion remained comparable across all activities, with mean translations of 6.3–8.3 mm and 7.3–9.3 mm for the medial and lateral condyles respectively. Only the swing phase of level walking and stair descent exhibited a significantly greater range of motion for the lateral over the medial compartment. Although intra-subject variability was low, considerable differences in joint kinematics were observed between subjects. The observed subject-specific movement patterns indicate that accurate assessment of individual pre-operative kinematics together with individual implant selection and/or surgical implantation decisions might be necessary before further improvement to joint replacement outcome can be achieved. [ABSTRACT FROM AUTHOR]

This study aimed to understand the ability of fixed-bearing posterior cruciate ligament (PCL)-retaining implants to maintain functionality of the PCL in vivo. To achieve this, elongation of the PCL was examined in six subjects with good clinical and functional outcomes using 3D kinematics reconstructed from video-fluoroscopy, together with multibody modelling of the knee. Here, length-change patterns of the ligament bundles were tracked throughout complete cycles of level walking and stair descent. Throughout both activities, elongation of the anterolateral bundle exhibited a flexion-dependent pattern with more stretching during swing than stance phase (e.g., at 40° flexion, anterolateral bundle experienced 3.9% strain during stance and 9.1% during swing phase of stair descent). The posteromedial bundle remained shorter than its reference length (defined at heel strike of the level gait cycle) during both activities. Compared with loading patterns of the healthy ligament, postoperative elongation patterns indicate a slackening of the ligament at early flexion followed by peak ligament lengths at considerably smaller flexion angles. The reported data provide a novel insight into in vivo PCL function during activities of daily living that has not been captured previously. The findings support previous investigations reporting difficulties in achieving a balanced tension in the retained PCL. [ABSTRACT FROM AUTHOR]