Search

Field‐effect transistors have strong applications in biosensing field from pH and glucose monitoring to genomics, proteomics, cell signaling assays, and biomedical diagnostics in general. Notable advantages are the high sensitivity (thanks to intrinsic amplification), quick response (useful for real‐time monitoring), suitability for miniaturization, and compact portable read‐out systems. The initial concept of ion‐sensitive field‐effect transistors evolved with the emergence of novel classes of materials beyond traditional semiconductors. Recently, 2D nanomaterials are redesigning the field providing superior performances with large surface‐to‐volume ratio, high carrier mobility, more effective local gating, high transconductance, and operation at low voltages. Here, after a brief conceptual introduction, we review progresses and perspectives of 2D materials field‐effect‐transistor biosensors with special focus on opportunities, most recent applications, present challenges, and future perspectives. [ABSTRACT FROM AUTHOR]

The growing interest in piezoresistive sensors has favored the development of numerous approaches and materials for their fabrication. Within this framework, carbon nanotubes (CNTs) are often employed. However, CNTs are a heterogeneous material with different morphological characteristics in terms of length and diameter, and, so far, experimental studies have not usually considered the effect of these parameters on the final sensor performances. Here, we observe how, by simply changing the CNTs length in a solvent-free mechanochemistry fabrication method, different porous 3D elastomeric nanocomposites with different electrical and mechanical properties can be obtained. In particular, the use of longer carbon nanotubes allows the synthesis of porous nanocomposites with better mechanical stability and conductivity, and with a nine-times-lower limit of detection (namely 0.2 Pa) when used as a piezoresistive sensor. Moreover, the material prepared with longer carbon nanotubes evidenced a faster recovery of its shape and electrical properties during press/release cycles, thus allowing faster response at different pressures. These results provide evidence as to how CNTs length can be a key aspect in obtaining piezoresistive sensors with better properties. [ABSTRACT FROM AUTHOR]

(1) Backgrond: Considering the positive effects of citicoline (CIT) in the management of some neurodegenerative diseases, the aim of this work was to develop CIT-Loaded Solid Lipid Nanoparticles (CIT-SLNs) for enhancing the therapeutic use of CIT in parkinsonian syndrome; (2) Methods: CIT-SLNs were prepared by the melt homogenization method using the self-emulsifying lipid Gelucire® 50/13 as lipid matrix. Solid-state features on CIT-SLNs were obtained with FT-IR, thermal analysis (DSC) and X-ray powder diffraction (XRPD) studies. (3) Results: CIT-SLNs showed a mean diameter of 201 nm, −2.20 mV as zeta potential and a high percentage of entrapped CIT. DSC and XRPD analyses evidenced a greater amorphous state of CIT in CIT-SLNs. On confocal microscopy, fluorescent SLNs replacing unlabeled CIT-SLNs released the dye selectively in the cytoplasm. Biological evaluation showed that pre-treatment of SH-SY5Y dopaminergic cells with CIT-SLNs (50 µM) before the addition of 40 µM 6-hydroxydopamine (6-OHDA) to mimic Parkinson's disease's degenerative pathways counteracts the cytotoxic effects induced by the neurotoxin, increasing cell viability with the consistent maintenance of both nuclear and cell morphology. In contrast, pre-treatment with CIT 50 and 60 µM or plain SLNs for 2 h followed by 6-OHDA (40 µM) did not significantly influence cell viability. (4) Conclusions: These data suggest an enhanced protection exerted by CIT-SLNs with respect to free CIT and prompt further investigation of possible molecular mechanisms that underlie this difference. [ABSTRACT FROM AUTHOR]

The development of highly sensitive, portable and low-cost sensors for the evaluation of ethanol content in liquid is particularly important in several monitoring processes, from the food industry to the pharmaceutical industry. In this respect, we report the optimization of two sensing approaches based on electrical impedance spectroscopy (EIS) and complementary double split ring resonators (CDSRRs) for the detection of ethanol in water. Miniaturized EIS sensors were realized with interdigitated electrodes, and the ethanol sensing was carried out in liquid solutions without any functionalization of the electrodes. Impedance fitting analysis, with an equivalent circuit over a frequency range from 100 Hz to 1 MHz, was performed to estimate the electric parameters, which allowed us to evaluate the amount of ethanol in water solutions. On the other hand, complementary double split ring resonators (CDSRRs) were optimized by adjusting the device geometry to achieve higher quality factors while operating at a low fundamental frequency despite the small size (useful for compact electronic packaging). Both sensors were found to be efficient for the detection of low amounts of ethanol in water, even in the presence of salts. In particular, EIS sensors proved to be effective in performing a broadband evaluation of ethanol concentration and are convenient when low cost is the priority. On the other end, the employment of split ring resonators allowed us to achieve a very low limit of detection of 0.2 v/v%, and provides specific advantages in the case of known environments where they can enable fast real-time single-frequency measurements. [ABSTRACT FROM AUTHOR]

Magnetic iron oxide nanoparticles have been extensively investigated due to their applications in various fields such as biomedicine, sensing, and environmental remediation. However, they need to be coated with a suitable material in order to make them biocompatible and to add new functionalities on their surface. This review is intended to give a comprehensive overview of recent advantages and applications of iron oxide nanoparticles coated by polydopamine film. The synthesis method of magnetic nanoparticles, their functionalization with bioinspired materials and (in particular) with polydopamine are discussed. Finally, some interesting applications of polydopamine-coated magnetic iron oxide nanoparticles will be pointed out. [ABSTRACT FROM AUTHOR]

[Display omitted] Nanocarbon/polymeric 3D porous composites have been widely developed as piezoresistive sensors due to their improved performances. Functionalized nanocarbon is usually used to allow its adsorption on the surface of porous polymeric material. However, both the functionalization and the surface localized distribution of the nanomaterial can limit the nanocarbon effect on conductivity and mechanical stability of the material thus affecting piezoresistive performances. A novel nanoarchitectonics strategy to prepare an elastomeric/carbon nanotubes (CNTs) 3D porous piezoresistive nanocomposite is developed. The fabrication route does not require complex apparatus and CNTs chemical functionalization. Moreover, foams of any shape and dimensions can be produced with neither complex machinery and procedures nor wastes production. The obtained material is characterized by the presence of well dispersed pristine CNTs on both surface and bulk of the polymeric matrix. The foam exhibited improved piezoresistive properties with excellent compressive stress (>150 kPa), sensitivity at low displacement (29 kPa−1) and limit of detection for both pressure (2 Pa) and extension (130 nm). These excellent features could allow the use of the as prepared nanocomposite in different applications ranging from wearable devices to robotic or infrastructure monitoring with outstanding flexibility. [ABSTRACT FROM AUTHOR]

The dielectric properties of YCTO bulk capacitors were investigated as a function of temperature from 25 °C to 150 °C and at microwave frequencies in comparison to a SiO 2 bulk sample. The results confirm the high-k character of the YCTO ceramic, in addition to the low AC conductivity, namely ε ′ = 40.1 and σ = 6 × 10 −8 S cm −1 at 1 MHz, and show a weak frequency and temperature (25 °C–150 °C) dependence. A temperature coefficient value of −601 ppm°C −1 for the dielectric constant ( TCε ′ ) was estimated at 100 kHz. In the GHz regime, a comparison with bulk SiO 2 confirms the higher YCTO dielectric permittivity. These results demonstrate high-k YCTO ceramic as a very promising material with high potentiality for electronic applications. [ABSTRACT FROM AUTHOR]

Current in-vitro 2D cultures and animal models present severe limitations in recapitulating human physiopathology with striking discrepancies in estimating drug efficacy and side effects when compared to human trials. For these reasons, microphysiological systems, organ-on-chip and multiorgans microdevices attracted considerable attention as novel tools for high-throughput and high-content research to achieve an improved understanding of diseases and to accelerate the drug development process towards more precise and eventually personalized standards. This review takes the form of a guide on this fast-growing field, providing useful introduction to major themes and indications for further readings. We start analyzing Organs-on-chips (OOC) technologies for testing the major drug administration routes: (1) oral/rectal route by intestine-on-a-chip, (2) inhalation by lung-on-a-chip, (3) transdermal by skin-on-a-chip and (4) intravenous through vascularization models, considering how drugs penetrate in the bloodstream and are conveyed to their targets. Then, we focus on OOC models for (other) specific organs and diseases: (1) neurodegenerative diseases with brain models and blood brain barriers, (2) tumor models including their vascularization, organoids/spheroids, engineering and screening of antitumor drugs, (3) liver/kidney on chips and multiorgan models for gastrointestinal diseases and metabolic assessment of drugs and (4) biomechanical systems recapitulating heart, muscles and bones structures and related diseases. Successively, we discuss technologies and materials for organ on chips, analyzing (1) microfluidic tools for organs-on-chips, (2) sensor integration for real-time monitoring, (3) materials and (4) cell lines for organs on chips. (Nano)delivery approaches for therapeutics and their on chip assessment are also described. Finally, we conclude with a critical discussion on current significance/relevance, trends, limitations, challenges and future prospects in terms of revolutionary impact on biomedical research, preclinical models and drug development. [ABSTRACT FROM AUTHOR]

Carbon nanotube polymeric composites are widely developed as piezoresistive sensors. Despite these materials showed improved mechanical stability, they are less sensible than carbon aerogel. Moreover, the piezoresistive properties of these nanocomposites cannot be tuned to adapt the sensor to the different applications. Here we observed as modifying solvent dilution in the hard template synthetic route, allow for the fabrication of porous piezoresistive nanocomposites with different limits of detection, working ranges and sensitivities. More in details three different foams with diverse features were produced. Although all the three materials presented outstanding performances, the porous material prepared at higher dilution showed an incredible limit of detection for displacement (∼50 nm) and pressure (0.2 Pa) that are respectively 2.6 and 10 times lower than that recorded at lower prepolymer dilutions. However lower dilutions allow to produce sensors able to monitor larger pressures ranges (up to ∼150 kPa), which are 3 times higher than that of recorded in composites prepared at higher dilutions. Moreover, all the materials evidenced fast response time and high mechanical and electronics stability. Therefore, we demonstrated as this approach easily allows the synthesis of nanocomposites with improved performances and different sensing properties that can be tuned depending on the needed application with an unprecedent flexibility. [Display omitted] • Porous piezoresistive nanocomposites with different properties was produced tuning the prepolymer dilution. • Higher dilutions allow the synthesis of piezoresistive with better conductivity, sensibility and limit of detections. • Lower dilution allows the synthesis of piezoresistive with larger working range and better mechanical strength. • All the dilutions allow the synthesis of piezoresistive materials with fast response time and good stability. • Hard template fabrication approach can be used to easily produce materials with different piezoresistive properties. [ABSTRACT FROM AUTHOR]

Hepatocellular carcinoma (HCC) is a highly lethal cancer, and although a few drugs are available for treatment, therapeutic effectiveness is still unsatisfactory. New drugs are urgently needed for hepatocellular carcinoma (HCC) patients. In this context, reliable preclinical assays are of paramount importance to screen the effectiveness of new drugs and, in particular, measure their effects on HCC cell proliferation. However, cell proliferation measurement is a time-consuming and operator-dependent procedure. The aim of this study was to validate an engineered miniaturized on-chip platform for real-time, non-destructive cell proliferation assays and drug screening. The effectiveness of Sorafenib, the first-line drug mainly used for patients with advanced HCC, was tested in parallel, comparing the gold standard 96-well-plate assay and our new lab-on-chip platform. Results from the lab-on-chip are consistent in intra-assay replicates and comparable to the output of standard crystal violet proliferation assays for assessing Sorafenib effectiveness on HCC cell proliferation. The miniaturized platform presents several advantages in terms of lesser reagents consumption, operator time, and costs, as well as overcoming a number of technical and operator-dependent pitfalls. Moreover, the number of cells required is lower, a relevant issue when primary cell cultures are used. In conclusion, the availability of inexpensive on-chip assays can speed up drug development, especially by using patient-derived samples to take into account disease heterogeneity and patient-specific characteristics. [ABSTRACT FROM AUTHOR]

The removal of pollutants, such as heavy metals, aromatic compounds, dyes, pesticides and pharmaceuticals, from water is still an open challenge. Many methods have been developed and exploited for the purification of water from contaminants, including photocatalytic degradation, biological treatment, adsorption and chemical precipitation. Absorption-based techniques are still considered among the most efficient and commonly used approaches thanks to their operational simplicity. In recent years, polydopamine-coated magnetic nanoparticles have emerged for the uptake of heavy metals in water treatment, since they combine specific affinity towards pollutants and magnetic separation capacity. In this context, this work focuses on the synthesis of polydopamine (PDA)-coated Super Paramagnetic Iron Oxide Nanoparticles (PDA@SPIONs) as adsorbents for Cu2+ ions, designed to serve as functional nanostructures for the removal of Cu2+ from water by applying a magnetic field. The synthetic parameters, including the amount of SPIONs and PDA, were thoroughly investigated to define their effects on the nanostructure features and properties. Subsequently, the ability of the magnetic nanostructures to bind metal ions was assessed on Cu2+-containing solutions. A systematic investigation of the prepared functional nanostructures was carried out by means of complementary spectroscopic, morphological and magnetic techniques. Inductively coupled plasma atomic emission spectroscopy (ICP-AES) measurements were performed in order to estimate the Cu2+ binding ability. The overall results indicate that these nanostructures hold great promise for future bioremediation applications. [ABSTRACT FROM AUTHOR]

This work aimed to evaluate the potential of the nanosystems constituted by dopamine (DA) and the antioxidant Citicoline (CIT) co-loaded in solid lipid nanoparticles (SLNs) for intranasal administration in the treatment of Parkinson disease (PD). Such nanosystems, denoted as DA-CIT-SLNs, were designed according to the concept of multifunctional nanomedicine where multiple biological roles are combined into a single nanocarrier and prepared by the melt emulsification method employing the self-emulsifying Gelucire® 50/13 as lipid matrix. The resulting DA-CIT-SLNs were characterized regarding particle size, surface charge, encapsulation efficiency, morphology, and physical stability. Differential scanning calorimetry, FT-IR, and X ray diffraction studies were carried out to gain information on solid-state features, and in vitro release tests in simulated nasal fluid (SNF) were performed. Monitoring the particle size at two temperatures (4 °C and 37 °C), the size enlargement observed over the time at 37 °C was lower than that observed at 4 °C, even though at higher temperature, color changes occurred, indicative of possible neurotransmitter decomposition. Solid-state studies indicated a reduction in the crystallinity when DA and CIT are co-encapsulated in DA-CIT-SLNs. Interestingly, in vitro release studies in SNF indicated a sustained release of DA. Furthermore, DA-CIT SLNs displayed high cytocompatibility with both human nasal RPMI 2650 and neuronal SH-SY5Y cells. Furthermore, OxyBlot assay demonstrated considerable potential to assess the protective effect of antioxidant agents against oxidative cellular damage. Thus, such protective effect was shown by DA-CIT-SLNs, which constitute a promising formulation for PD application. [ABSTRACT FROM AUTHOR]

The structural, dielectric, and ferroelectric characterization of multiphase Bi‐Fe‐O prepared with an excess of Bi up to 20% is reported. It is found that the dominant phase in all samples is the BiFeO3 perovskite in addition to an increasing amount of the Bi‐rich sillenite phases (Bi12.5Fe0.5O19.48/Bi25FeO39) with the Bi excess content. At room temperature, the multiphase Bi‐Fe‐O results in advanced electrical properties, with higher dielectric constant (161 at 1 MHz) and low losses (tanδ = 0.032 at 1 MHz). The ferroelectric character of multiphase ceramics is confirmed by PUND measurements, which shows increased polarization values and coercive field with respect to the single phase ceramics. Multiphase Bi‐Fe‐O ceramics prepared with Bi excess (up to 20%) are morphologically, structurally, dielectrically, and ferroelectrically investigated. Improved dielectric and ferroelectric properties are observed in the multiphase samples with respect to the single phase bismuth ferrite and further insight on the effect of microstructure on the ceramics dielectric properties is achieved. [ABSTRACT FROM AUTHOR]

Metal halide perovskite materials have received significant attention in recent years due to their promising properties and potential applications, particularly their use as scintillator detectors, which is rapidly emerging due to their promising advantages as detectors, such as low costs, fast response, high quantum yield, strong absorption, scalability, flexibility, and emission wavelength tunability. Given the effectiveness of perovskites as α particle detectors and the potential of 10B as a neutron converter, in this paper a 10B converting layer was coupled with an all-inorganic lead halide perovskite (CsPbBr3) layer aiming to create a thermal neutron detector. Specifically, a 1 µ m thin film of 10B and a 1 µ m thin layer of CsPbBr3 were deposited on a suitable substrate using a laser ablation process. The fabricated detector was subjected to a comprehensive characterization, including structural, morphological, and detection properties. As output, the films exhibit macroscopically uniform behavior and good adhesion to the substrate. In terms of thermal neutron efficiency, an efficiency of (7.9 ± 0.3)% was determined with respect to a commercial detector (EJ-426), which corresponds to an intrinsic efficiency of (2.5 ± 0.1)%. Also, Monte Carlo simulations were conducted, and the optimum value of the 10B layer thickness was found to be 2.5 µ m. [ABSTRACT FROM AUTHOR]

In this paper, by means of high-resolution photoemission, soft X-ray absorption and atomic force microscopy, we investigate, for the first time, the mechanisms of damaging, induced by neutron source, and recovering (after annealing) of p-i-n detector devices based on hydrogenated amorphous silicon (a-Si:H). This investigation will be performed by mean of high-resolution photoemission, soft X-Ray absorption and atomic force microscopy. Due to dangling bonds, the amorphous silicon is a highly defective material. However, by hydrogenation it is possible to reduce the density of the defect by several orders of magnitude, using hydrogenation and this will allow its usage in radiation detector devices. The investigation of the damage induced by exposure to high energy irradiation and its microscopic origin is fundamental since the amount of defects determine the electronic properties of the a-Si:H. The comparison of the spectroscopic results on bare and irradiated samples shows an increased degree of disorder and a strong reduction of the Si-H bonds after irradiation. After annealing we observe a partial recovering of the Si-H bonds, reducing the disorder in the Si (possibly due to the lowering of the radiation-induced dangling bonds). Moreover, effects in the uppermost coating are also observed by spectroscopies. [ABSTRACT FROM AUTHOR]

Human activities significantly contribute to worldwide spread of phytopathological adversities. Pathogen-related food losses are today responsible for a reduction in quantity and quality of yield and decrease value and financial returns. As a result, "early detection" in combination with "fast, accurate, and cheap" diagnostics have also become the new mantra in plant pathology, especially for emerging diseases or challenging pathogens that spread thanks to asymptomatic individuals with subtle initial symptoms but are then difficult to face. Furthermore, in a globalized market sensitive to epidemics, innovative tools suitable for field-use represent the new frontier with respect to diagnostic laboratories, ensuring that the instruments and techniques used are suitable for the operational contexts. In this framework, portable systems and interconnection with Internet of Things (IoT) play a pivotal role. Here we review innovative diagnostic methods based on nanotechnologies and new perspectives concerning information and communication technology (ICT) in agriculture, resulting in an improvement in agricultural and rural development and in the ability to revolutionize the concept of "preventive actions", making the difference in fighting against phytopathogens, all over the world. [ABSTRACT FROM AUTHOR]

Hydrogenated amorphous silicon (a-Si:H) has been proposed as a suitable material for particle detection applications thanks to its property to be deposited over a large area and above a variety of different substrates, including flexible materials. Moreover, the low cost and intrinsic radiation tolerance made this material appealing in applications where high fluences are expected, e.g. in high energy physics experiments. In order to optimize the device geometry and to evaluate its electrical behaviour in different operating conditions, a suitable Technology CAD (TCAD) design methodology can be applied. In this work, carried out in the framework of the HASPIDE INFN project, we propose an innovative approach to the study of charge transport within the material, using the state-of-the-art Synopsys Advanced TCAD Suite. Different custom mobility models have been devised and implemented within the code as external PMI (Physical Model Interfaces), starting from the Poole–Frenkel model and accounting for different dependencies on temperature and internal potential distribution, thus resulting in a new mobility model embedded within the code. Simple test structures, featuring p-i-n diodes have been simulated and compared to experimental data as a benchmark. The overall aim was to account for the effect of different biasing conditions (namely, different electrical potential and electric field distribution within the device) and operating conditions (e.g. temperature). This work fosters the use of commercially available TCAD suite such as Synopsys Sentaurus, largely diffused in the radiation detection scientific community, for the design and optimization of innovative a-Si:H devices for particle detection applications. [ABSTRACT FROM AUTHOR]

Herein we present a straightforward approach for the use of polydopamine (PDA) in adsorption of heavy metals from aqueous solutions. This is achieved by fabricating a healthy and environmentally friendly polydimethylsiloxane (PDMS) foam with a mussel inspired PDA layer deposited on the surface. Critical adsorption parameters (pH, temperature and PDA thickness) are optimized by the application of experimental design methodology. Adsorption kinetics and isotherms are studied in detail evidencing a good fitting with Langmuir isotherm and pseudo-second-order kinetics thus suggesting the occurrence of a chemical sorption process with monolayer nature between metals and PDMS/PDA foam. Intraparticle diffusion model evidences good accessibility and high affinity of binding sites on PDA surface. Once adsorbed, metals are reduced to a lower toxic form and can be then removed by a mild acidic treatment thus being easily collected and stocked. [ABSTRACT FROM AUTHOR]

Abstract Aerosol particulate matter (PM) is a known risk factor for lung and liver cancer. In particular, PM under 1 μm in diameter (PM 1) is very dangerous for health, affecting the respiratory system with several heavy outcomes and reaching other human districts like liver, where foreign substances are processed. Today PM 1 is still difficult to be detected on-field with standard techniques and this paper reports a comparison between two sensing approaches for environmental particulate monitoring, which are suitable for miniaturization and integration into portable and low-cost devices. Specifically, transducers based on surface acoustic waves (SAW) and electrochemical impedance spectroscopy (EIS) were comparatively investigated as alternatives to more common but also expensive optical methods. Moreover, their performances were evaluated for the detection of nanoparticles of different dimensions (1 μm, 200 nm and 40 nm) to mimic different compositions of PM 1 and reach a size scale which is an order of magnitude below present literature. Notably, both transduction methods were able to detect the presence of PM 1 particulate. The SAW-based approach showed better performances in terms of sensitivity and detection of nanoscale particles, although the EIS strategy has a competitive sensitivity considering also its even lower cost. Graphical abstract Unlabelled Image Highlights • We describe two innovative strategies to detect airborne particulate of paramount concern in lung and liver carcinogenesis. • Surface acoustic Waves and Electrochemical Impedance Spectroscopy sensors were used to detect ultrafine particulate. • Both developed sensing platforms are suitable for further miniaturization and on-field applications. [ABSTRACT FROM AUTHOR]

Mixed iron-manganese oxide nanoparticles, synthesized by a simple procedure, were used to remove nickel ion from aqueous solutions. Nanostructures, prepared by using different weight percents of manganese, were characterized by transmission electron microscopy, selected area diffraction, X-ray diffraction, Raman spectroscopy, and vibrating sample magnetometry. Adsorption/desorption isotherm curves demonstrated that manganese inclusions enhance the specific surface area three times and the pores volume ten times. This feature was crucial to decontaminate both aqueous samples and food extracts from nickel ion. Efficient removal of Ni2+ was highlighted by the well-known dimethylglyoxime test and by ICP-MS analysis and the possibility of regenerating the nanostructure was obtained by a washing treatment in disodium ethylenediaminetetraacetate solution. [ABSTRACT FROM AUTHOR]

Authors aimed to provide a magnetic responsiveness to bone-mimicking nano-hydroxyapatite (n-HA). For this purpose, dextran-grafted iron oxide nanoarchitectures (DM) were synthesized by a green-friendly and scalable alkaline co-precipitation method at room temperature and used to functionalize n-HA crystals. Different amounts of DM hybrid structures were added into the nanocomposites (DM/n-HA 1:1, 2:1 and 3:1weight ratio) which were investigated through extensive physicochemical (XRD, ICP, TGA and Zeta-potential), microstructural (TEM and DLS), magnetic (VSM) and biological analyses (MTT proliferation assay). X-ray diffraction patterns have confirmed the n-HA formation in the presence of DM as a co-reagent. Furthermore, the addition of DM during the synthesis does not affect the primary crystallite domains of DM/n-HA nanocomposites. DM/n-HAs have shown a rising of the magnetic moment values by increasing DM content up to 2:1 ratio. However, the magnetic moment value recorded in the DM/n-HA 3:1 do not further increase showing a saturation behaviour. The cytocompatibility of the DM/n-HA was evaluated with respect to the MG63 osteoblast-like cell line. Proliferation assays revealed that viability, carried out in the absence of external magnetic field, was not affected by the amount of DM employed. Interestingly, assays also suggested that the DM/n-HA nanocomposites exhibit a possible shielding effect with respect to the anti-proliferative activity induced by the DM particles alone. [ABSTRACT FROM AUTHOR]

Lower genital tract infections caused by both sexually and not-sexually transmitted pathogens in women are a key public health priority worldwide, especially in developing countries. Since standard analyses are time-consuming, appropriate therapeutic intervention is often neglected or delayed. Lab-on-chips and biosensors open new perspectives and offer innovative tools to simplify the diagnosis by medical staff, especially in countries with inadequate resources. Here we report a biosensing platform based on Electrochemical Impedance Spectroscopy (EIS) that allows multiplexed detection of Candida albicans , Streptococcus agalactiae and Chlamydia trachomatis with a single biochip, enabling a quick screening thanks to the presence of different immobilized antibodies, each specific for one of the different target pathogens. [ABSTRACT FROM AUTHOR]

Celiac disease (CD) is one of the most common digestive disorders caused by an abnormal immune reaction to gluten. So far there are no available therapies, the only solution is a strict gluten-free diet, which however could be very challenging as gluten can be hidden in many food products. Furthermore an additional problem is related to cross-contamination of nominal gluten-free foods with gluten-based ones during manufacturing. Here we propose a lab on chip platform as a powerful tool to help food manufacturers to evaluate the real amount of gluten in their products by an accurate in-situ control of the production chain and maybe to specify the real gluten content in packages labeling. Our portable gliadin-immunochips, based on an electrochemical impedance spectroscopy transduction method, were first calibrated and then validated for both liquid and solid food matrixes by analyzing different beers and flours. The high specificity of our assay was also demonstrated by performing control experiments on rice and potatoes flours containing prolamin-like proteins. We achieved limit of quantification of 0.5 ppm for gliadin that is 20 times lower than the worldwide limit established for gluten-free food while the method of analysis is faster and cheaper than currently employed ELISA-based methods. Moreover our results on food samples were validated through a mass spectrometry standard analysis. [ABSTRACT FROM AUTHOR]

Solid-state ionic conductors embodying either protons or lithium ions are very attractive for large-area electrochromic (EC) devices. In this work, aiming at the preparation of a gel polymer electrolyte (GPE), two cheaper and non-toxic commercial resins are used: a urethane-based prepolymer (NOA65) and a vinyl acetate-based resin (MASTIFLEX). They are employed as host matrices to trap the liquid constituents, made of lithium perchlorate-propylene carbonate (LiClO 4 -PC). Thermogravimetric analyses indicate that both resins show excellent thermal performance. Several GPE formulations are investigated with respect to electrical and optical properties, varying the polymer-to-liquid ratio and LiClO 4 concentration. The EC devices made with the two GPEs are also characterized in terms of optical contrast, switching kinetics and repetitive switching cycles. These activities made it possible to find the best formulations finally employed for the fabrication of 100 cm2 large area EC devices. The obtained results demonstrate that low-cost GPEs based on commercial polymers are electrochemically stable as ion-conducting media for EC devices. • Two low cost polymeric resins have been used as gel polymer electrolytes for the fabrication of electrochromic devices. • Optimization of electrolytes formulation in order to maximize the ionic conductivity. • Fabrication of a 100 cm2 large area electrochromic device. [ABSTRACT FROM AUTHOR]

Background: The loss of nigrostriatal neurons containing dopamine (DA) together with the "mitochondrial dysfunction" in midbrain represent the two main causes related to the symptoms of Parkinson's disease (PD). Hence, the aim of this investigation is to co-administer the missing DA and the antioxidant grape seed-derived proanthocyanidins (grape seed extract, GSE) in order to increase the levels of the neurotransmitter (which is unable to cross the Blood Brain Barrier) and reducing the oxidative stress (OS) related to PD, respectively. Methods: For this purpose, we chose Solid Lipid Nanoparticles (SLN), because they have been already proven to increase DA uptake in the brain. DA-SLN adsorbing GSE (GSE/DA-SLN) were formulated and subjected to physico-chemical characterization, and their cytocompatibility and protection against OS were examined. Results: GSE was found on SLN surface and release studies evidenced the efficiency of GSE in preventing DA autoxidation. Furthermore, SLN showed high mucoadhesive strength and were found not cytotoxic to both primary Olfactory Ensheathing and neuroblastoma SH-SY5Y cells by MTT test. Co-administration of GSE/DA-SLN and the OS-inducing neurotoxin 6-hydroxydopamine (100 μM) resulted in an increase of SH-SY5Y cell viability. Conclusions: Hence, SLN formulations containing DA and GSE may constitute interesting candidates for non-invasive nose-to-brain delivery. [ABSTRACT FROM AUTHOR]

Energy efficient, low-cost, user-friendly, and green methods for the removal of toxic phenolic compounds from aqueous solution are necessary for waste treatment in industrial applications. Herein we present an interesting approach for the utilization of oxidized carbon nanotubes (CNTs) in the removal of phenolic compounds from aqueous solution. Dried pristine CNTs were stably incorporated in a solid porous support of polydimethylsiloxane (PDMS) facilitating the handling during both oxidation process of the nanomaterial and uptake of phenolic compounds, and enabling their safe disposal, avoiding expensive post-treatment processes. The adsorption studies indicated that the materials can efficiently remove phenolic compounds from water with different affinities towards different phenolic compounds. Furthermore, the adsorption kinetics and isotherms were studied in detail. The experimental data of adsorption fitted well with Langmuir and Freundlich isotherms, and pseudo-second-order kinetics, and the results indicated that the adsorption process was controlled by a two-step intraparticle diffusion model. The incorporation of CNTs in polymeric matrices did not affect their functionality in phenol uptake. The material was also successfully used for the removal of phenolic compounds from agricultural waste, suggesting its possible application in the treatment of wastewater. Moreover, the surface of the material could be regenerated, decreasing treatment costs. [ABSTRACT FROM AUTHOR]