Search

An efficient ITO-free top-illuminated organic photovoltaic (TOPV) based on small molecular planar heterojunction was achieved by spinning a buffer layer of poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS), on the Ag-AgOx anode. The PEDOT:PSS thin film separates the active layer far from the Ag anode to prevent metal quenching and redistributes the strong internal optical field toward dissociated interface. The thickness and morphology of this anodic buffer layer are the key factors in determining device performances. The uniform buffer layer contributes a large short-circuit current and open-circuit voltage, benefiting the final power conversion efficiency (PCE). The TOPV device with an optimal PEDOT:PSS thickness of about 30 nm on Ag-AgOx anode exhibits the maximum PCE of 1.49%. It appreciates a 1.37-fold enhancement in PCE over that of TOPV device without buffer layer. [ABSTRACT FROM AUTHOR]

In this paper, we investigate the carrier injection and transport characteristics in iridium(III)bis[4,6-(di-fluorophenyl)-pyridinato-N,C2']picolinate (FIrpic) doped phosphorescent organic light-emitting devices (OLEDs) with oxadiazole (OXD) as the bipolar host material of the emitting layer (EML). When doping Firpic inside the OXD, the driving voltage of OLEDs greatly decreases because FIrpic dopants facilitate electron injection and electron transport from the electron-transporting layer (ETL) into the EML. With increasing dopant concentration, the recombination zone shifts toward the anode side, analyzed with electroluminescence (EL) spectra. Besides, EL redshifts were also observed with increasing driving voltage, which means the electron mobility is more sensitive to the electric field than the hole mobility. To further investigate carrier injection and transport characteristics, FIrpic was intentionally undoped at different positions inside the EML. When FIrpic was undoped close to the ETL, driving voltage increased significantly which proves the dopant-assisted-electron-injection characteristic in this OLED. When the undoped layer is near the electron blocking layer, the driving voltage is only slightly increased, but the current efficiency is greatly reduced because the main recombination zone was undoped. However, non-negligible FIrpic emission is still observed which means the recombination zone penetrates inside the EML due to certain hole-transporting characteristics of the OXD. [ABSTRACT FROM AUTHOR]

Transition metal oxides, such as molybdenum trioxide (MoO3), tungsten trioxide (WO3) and vanadium pent-oxide (V2O5), are well-known hole injection materials used for organic electronic devices. These materials promote work functions of anodes, reduce energy barriers, and facilitate hole transport at the interface between the inorganic anode and organic hole-transporting layer (HTL). In this study, we characterized the transmittance spectra and work function of these materials. Furthermore, we employed a hole-injection layer (HIL) in a blue phosphorescent organic light-emitting diode (OLED) to evaluate their hole-injection capacity by detecting the variation in the emission spectra. Thus, we utilized an OLED structure that has fast electron transporting dynamics to establish the recombination zone located at emitting layer and a partial HTL close to the anode. We used these three transition metal oxides individually as HILs sandwiched between the ITO anode and HTL and concluded that the strength of emissive light from the HTL was determined by their hole-injection capacity, depending on work function. The small amount of HTL emission light of the V2O5 OLED was explained by the high work function of 5.8 eV for the V2O5 film. However, the V2O5 OLED demonstrated the least favorable optoelectrical performance because of its low transmittance and high resistance of the V2O5 film. Ultimately, the 5 nm-MoO3 OLED exhibited the highest device performance because of its high material conductivity and transparency in the visible band. [ABSTRACT FROM AUTHOR]

The novel ambipolar hosts of o-CbzBz and o-DiCbzBz contain carbazole and benzimidazole through an ortho-connection. The orthogonal conformations cause the triplet state to be confined at the carbazole units to secure efficient energy transfer. The phosphorescent organic light-emitting diodes (PhOLEDs) show a high current efficiency, power efficiency, and low efficiency roll-off. o-DiCbzBz can be used as a host for sky-blue, green, and orange-red PhOLEDs, giving 57.5, 78.4, and 60.3 cd/A, respectively. [ABSTRACT FROM AUTHOR]

The novel ambipolar hosts of o-CbzBz and o-DiCbzBz contain carbazole and benzimidazole through an ortho-connection. The orthogonal conformations cause the triplet state to be confined at the carbazole units to secure efficient energy transfer. The phosphorescent organic light-emitting diodes (PhOLEDs) show a high current efficiency, power efficiency, and low efficiency roll-off. o-DiCbzBz can be used as a host for sky-blue, green, and orange-red PhOLEDs, giving 57.5, 78.4, and 60.3 cd/A, respectively. [ABSTRACT FROM AUTHOR]

This paper introduces the fundamental physical characteristics of organic photovoltaic (OPV) devices. Photoelectric conversion efficiency is crucial to the evaluation of quality in OPV devices, and enhancing efficiency has been spurring on researchers to seek alternatives to this problem. In this paper, we focus on organic photovoltaic (OPV) devices and review several approaches to enhance the energy conversion efficiency of small molecular heterojunction OPV devices based on an optimal metal-phthalocyanine/fullerene (C60) planar heterojunction thin film structure. For the sake of discussion, these mechanisms have been divided into electrical and optical sections: (1) Electrical: Modification on electrodes or active regions to benefit carrier injection, charge transport and exciton dissociation; (2) Optical: Optional architectures or infilling to promote photon confinement and enhance absorption. [ABSTRACT FROM AUTHOR]

In this paper, we had quantitatively investigated the photoluminescence of organic emitter on a Si substrate with periodically corrugated metal thin film experimentally and theoretically. Due to the plasmonic coupling by the metal gratings, 4.3 times and 1.7 times enhancements in optical intensities were observed at specified and full viewing angles at certain wavelengths, respectively. Good agreement of angular-frequency versus in-plane wavevector (ω-k) curves between experiments and calculations were obtained when varying organic materials, metal materials, and grating pitches. Two different metal materials were used, which show slight shift in ω-k curves due to the high sensitivity of the surface plasmon to the relative permittivity. [ABSTRACT FROM AUTHOR]

Transient current density and luminance from an organic light-emitting diode (OLED) driven by voltage pulses were investigated. Waveforms with different repetition rate, duty cycle, off-period, and on-period were used to study the injection and transport characteristics of electron and holes in an OLED under pulse operation. It was found that trapped electrons inside the emitting layer (EML) and the electron transporting layer (ETL) material, tris(8-hydroxyquinolate)aluminum (Alq3) helped for attracting the holes into the EML/ETL and reducing the driving voltage, which was further confirmed from the analysis of capacitance–voltage and displacement current measurement. The relaxation time and trapped filling time of the trapped electrons in Alq3 layer were ~200 µs and ~600 µs with 6 V pulse operation, respectively. [ABSTRACT FROM AUTHOR]