Search

In this paper, a full 3-D numerical scheme based on the finite-difference time-domain method is used to predict the electromagnetic (EM) radiated interference generated by 42-V vehicle power electronic driven electrical loads. An experimental setup has been arranged in order to validate the proposed simulation tool. To this aim, the features of a semi-anechoic EM chamber have been exploited in order to operate in a shielded test site for the measurement of near-field radiated emissions. Two different 3-D geometrical configurations of realistic vehicle installations of the loads are studied. A comparative analysis among measured and computed results is performed. A good agreement between simulated and measured data is obtained. The proposed approach is suitable for the prediction of radiated EM interference generated by dc/dc converters and, particularly, by dual-voltage vehicle electric plants. In fact, due to the presence of complicated layout, the prediction of EM emissions can be a useful task in order to evaluate the EM compatibility (EMC) compliance from the design stage. Furthermore, with the growing market penetration of the "More Electric Vehicle" (MEV) concept in designing new vehicle electrical architectures, low-cost test methods for EMC assessments and suitable technical standard requirements have to be introduced. The proposed simulation tool can be usefully adopted to this aim. As an important advantage, it requires only a current measurement in the time domain. Such measurement does not need the use of a special test site or of a radiated field measurement setup. [ABSTRACT FROM AUTHOR]

This article investigates the feasibility of using a simplified approach, based on the measurement of power ratio parameters, for harmonic emissions assessment at the point of common coupling (PCC). The proposed approach comes from the common concept of power factor correction and the definitions of the IEEE Std. 1459-2010, where line utilization and harmonic pollution levels are evaluated by means of ratios between the power quantities of the apparent power decomposition. In addition to the IEEE Std. 1459–2010 indicators, in this article, the behavior is studied of additional parameters that are conceptually similar to those defined by the IEEE Std. 1459-2010. The suitability of such parameters is discussed, for both single- and three-phase balanced/unbalanced cases, taking into account both their behavior in different scenarios and their effectiveness when the measurement uncertainty is taken into account. The study is supported by some simulation results that have been obtained on an IEEE benchmark power system, which allows reproducing linear and nonlinear load conditions, balanced and unbalanced operating conditions, and the presence of capacitors for power factor correction. [ABSTRACT FROM AUTHOR]

The monitoring and the management of smart grid require an advanced communication infrastructure. The time synchronization is among the most important services such an infrastructure should offer. Several solutions are available to disseminate the time information in a distributed system; for instance, most of the times a global positioning system (GPS) receiver is used to recover accurate time information. However, GPS receivers need a clear view of the sky. Other solutions, like the use of a network-based synchronization mechanism, require a dedicated communication infrastructure, which is not always feasible for economical reason. Thus, the use of the power grid itself to disseminate a time signal is extremely interesting. The aim of this article is to investigate the possibility to distribute a time signal over a medium voltage (MV) grid using a chirp-based modulation. The timing data are coded using IRIG-B time code. Such an approach does not require the installation of a dedicated infrastructure, and it is noninvasive, because the signal is transmitted on a different band with the respect to power line communication (PLC). The effectiveness of the approach has been experimentally evaluated on a test MV line available in a laboratory. Although the tested chirp-based symbol has a limited frequency bandwidth (80 kHz), the jitter in the identification of the start of frame is on the order of 7.5 $\mu \text{s}$ , fulfilling the requirements of the most smart grid applications. [ABSTRACT FROM AUTHOR]

This article presents an enhanced system for real-time power flow monitoring and control (PFMC) for microgrids integration in medium-voltage (MV) distribution networks. The developed solution includes both system architecture and the monitoring and control algorithms, and it has low implementation and installation costs. It is based on the use of hardware and software solutions previously proposed by the authors, i.e., a distributed measurement, a control and communication architecture, and a supervisory control and data acquisition (SCADA) software, which have been enhanced and integrated for the considered application. The SCADA implements a load flow (LF) algorithm for real-time power flows estimation in the MV network branches based only on the load powers measurements at low-voltage level. The system architecture includes new devices specifically designed for distributed generators (DGs) and energy storage systems (ESSs) remote control. The algorithm implemented on the developed PFMC system has been enhanced by including a real-time verification of LF results, which allows detecting devices' unavailability or malfunction occurrence. The PFMC has been implemented in the islanded scenario of the MV distribution network of Ustica Island (Mediterranean Sea) and it has been verified experimentally, in a measurement campaign of one year. In order to deal with different scenarios of DGs/ESSs presence in the microgrid, different operating conditions were reproduced during the measurement campaign, including the case of power flow inversion; such conditions have been obtained by means of an ad hoc developed on-field DG emulator which was remotely controlled by the SCADA system. [ABSTRACT FROM AUTHOR]

The monitoring and the management of smart grid require an advanced communication infrastructure. The time synchronization is among the most important services such an infrastructure should offer. Several solutions are available to disseminate the time information in a distributed system; for instance, most of the times a global positioning system (GPS) receiver is used to recover accurate time information. However, GPS receivers need a clear view of the sky. Other solutions, like the use of a network-based synchronization mechanism, require a dedicated communication infrastructure, which is not always feasible for economical reason. Thus, the use of the power grid itself to disseminate a time signal is extremely interesting. The aim of this article is to investigate the possibility to distribute a time signal over a medium voltage (MV) grid using a chirp-based modulation. The timing data are coded using IRIG-B time code. Such an approach does not require the installation of a dedicated infrastructure, and it is noninvasive, because the signal is transmitted on a different band with the respect to power line communication (PLC). The effectiveness of the approach has been experimentally evaluated on a test MV line available in a laboratory. Although the tested chirp-based symbol has a limited frequency bandwidth (80 kHz), the jitter in the identification of the start of frame is on the order of 7.5 $\mu \text{s}$ , fulfilling the requirements of the most smart grid applications. [ABSTRACT FROM AUTHOR]

This paper aims at characterizing and improving the metrological performances of current and voltage instrument transformers (CTs and VTs) in harmonic measurements in the power system. A theoretical analysis is carried out to demonstrate that, due to the iron core nonlinearity, CT and VT output signal is distorted even when the input signal is a pure sine wave. Starting from this analysis, a new method for CT and VT characterization and compensation is proposed. In a first step, they are characterized in sinusoidal conditions and the harmonic phasors of the distorted output are measured; in the second step, these phasors are used to compensate the harmonic phasors measured in normal operating conditions, which are typically distorted. The proposed characterization and compensation techniques are called SINusoidal characterization for DIstortion COMPensation (SINDICOMP). Several experimental tests, using high-accuracy calibration setups, have been performed to verify the proposed methods. The experimental results showed that the SINDICOMP technique assures a significant improvement of CT and VT metrological performances in harmonic measurements. [ABSTRACT FROM AUTHOR]

A novel measurement approach for power-flow analysis in medium-voltage (MV) networks, based on load power measurements at low-voltage level in each secondary substation (SS) and only one voltage measurement at the MV level at primary substation busbars, was proposed by the authors in previous works. In this paper, the method is improved to cover the case of temporary unavailability of load power measurements in some SSs. In particular, a new load power estimation method based on artificial neural networks (ANNs) is proposed. The method uses historical data to train the ANNs and the real-time available measurements to obtain the load estimations. The load-flow algorithm is applied with the estimated load powers, and the MV network state variables are obtained. The proposed method is validated for the real MV distribution network of the island of Ustica. The loads of selected SSs are estimated for two full days of different seasons. In comparison with previous works, satisfactory results are obtained in terms of uncertainty in the calculated power flows, thus suggesting the applicability of the proposed method for real-time monitoring of MV distribution networks. [ABSTRACT FROM AUTHOR]

The smart grid (SG) approach is based on a strong interaction between the network communication infrastructure and the power grid. Usually the management of the infrastructure is done by the distribution system operators (DSOs) that are worried about the increasing managing complexity due to the presence of increasing number of distributed energy resources and electrical vehicles. The use of software-defined networking (SDN) may simplify the network configuration and management for DSO, as highlighted from previous research works. The objective of this paper is to introduce and characterize an internet protocol (IP)-based communication architecture with specialized SDN bridges operating also over narrowband power line communication (PLC) to reach the last mile applications (e.g., smart meters and inverters). The feasibility of this approach depends on the communication performance of the supervisory level used to dynamically configure the SDN bridges. The characterization of this level is done using the following performance indicators: the round trip time (RTT), the packet loss (PL) ratio, and the actual IP throughput. The experimental results show the feasibility of the proposed architecture, since the limitations are given only by the physical implementation of the PLC modem. In detail, results of the case study show that the minimum RTT is on the order of 30 ms, the PL ratio is always less than 1.7% and the maximum throughput is of 95 Mbit/s, fully compatible with the requirements of the applications. [ABSTRACT FROM AUTHOR]

This paper presents a method for the detection of series arc faults in electrical circuits, which has been developed starting from an experimental characterization of the arc fault phenomenon and an arcing current study in several test conditions. Starting from this, the authors have found that is it possible to suitably detect arc faults by means of a high-resolution low-frequency harmonic analysis of current signal, based on chirp zeta transform, and a proper set of indicators. The proposed method effectiveness is shown by means of experimental tests, which were carried in both arcing and nonarcing conditions and in the presence of different loads, chosen according to the UL 1699 standard requirements. [ABSTRACT FROM PUBLISHER]

In this paper, a method to characterize the high-frequency (HF) behavior of six pack insulated gate bipolar transistors (IGBTs) power module (PM) is presented. The method is based on experimental measurements at the external pins of the device and it allows one to extract internal inductive and capacitive parasitic coupling without the knowledge of structural and physical parameters of the PM. The HF model of a six pack IGBTs PM has been developed, in the frequency range of 150 kHz–30 MHz, and it has been implemented in MATLAB environment. The method has been experimentally validated by comparing the frequency behavior of the PM with the simulated response. Moreover, the HF conducted disturbances, generated by the PM and measured in the dc link, have been compared with the simulation results verifying the proposed model. [ABSTRACT FROM AUTHOR]

This paper deals with the issue of measurement device placement for load flow analysis in medium-voltage (MV) distribution networks. The study is carried out using an innovative measurement algorithm for load flow analysis developed by the authors. It is based on low-voltage (LV) load power measurements applied on a backward/forward algorithm for the load flow resolution. The final aim is to identify the most suitable number and placement of the LV measurement points in order to limit the uncertainty on the power flow estimation to a target value. The proposed approach is based on the uncertainty evaluation of the estimated power flows; a sensitivity analysis is performed in order to assess the uncertainty contribution of each LV power measurement to the estimated power flow upstream of each MV feeder of the distribution network. The LV measurement device placement is presented and discussed in a real case study, i.e., the distribution network of the Ustica Island. [ABSTRACT FROM AUTHOR]

In this paper, a new solution is proposed for the remote monitoring and control of distributed generators (DGs) and energy storage systems (ESSs) connected to low-voltage distribution networks. The proposed system fulfills the in-force standard requirements for the connection of DGs to the utility grid. Moreover, it allows implementing some enhanced functions for the remote control of inverters of DGs and ESSs, not only in terms of disconnection but also in terms of voltage regulation and power shuttering. The proposed solution is based on a new interface protection system and a dedicated secondary substation concentrator, which allows the communication between the distributed system operator and the inverters of DGs or ESSs. The proposed system was tested on field in the electrical network of the island of Ustica. An experimental characterization was carried out to find the best communication conditions, i.e., the frequency band with the lowest noise and attenuation, considering the signal amplitude and signal-to-noise ratio constraints, as well as the desired transmission data rate and transfer time. [ABSTRACT FROM PUBLISHER]

This paper is focused on the possibility of employing narrow band power line communication (PLC) in medium voltage (MV) distribution networks. The topic is investigated by means of both simulations and experimental tests, which were carried out in the distribution network of Ustica Island. In detail, a two-way MV communication was tested between two secondary substations connected by an MV cable power line. Each substation has a by-pass connection at MV bus-bars and an MV/LV oil filled power transformer. In this paper, the MV and the PLC systems under test are described and the experimental tests are presented, which were carried out to evaluate the parameters of the simulation model. The aforesaid model is described and a comparison is shown between simulation and results of experiments, which were carried out in the presence of voltage net, i.e., 24 kV. Finally, the possibility is investigated of a reliable communication and the faster achievable bit-rate; the analysis is performed by means of further experimental results of several communication tests, which were carried out with different modulation techniques. [ABSTRACT FROM AUTHOR]

This paper is focused on the measurement issues and procedures for the characterization of medium voltage grids for narrowband power line communications (NB-PLCs), in the perspective of the use and integration of such technology into smart grids communication networks. The fundamentals are given for the characterization of the PLC channel, by means of noise and attenuation measurements. Suitable procedures are also developed for the characterization and modeling of the power system components in the frequency range of interest. Furthermore, the complete model of the PLC system is experimentally validated in a real case study. [ABSTRACT FROM PUBLISHER]

The aim of this paper is to develop a complete model of a power-line communication (PLC) system operating on a medium-voltage (MV) network. The core-shield configuration was chosen for signal transmission in the power cables. In order to validate the developed model experimental, the medium-voltage network of the Favignana island was used to carry out detailed testing. The transmission was performed between two transformer substations in the presence of mains voltage (i.e., 24 kV). ST7540 FSK power-line transceivers, together with capacitive coupling interfaces, were used for the transmission and the reception of the communication signal. The correlation between the experimental measurements and the simulation results would appear to validate the use of the developed model for the analysis of MV transmission channels. [ABSTRACT FROM PUBLISHER]

A complete model of a power-line communication (PLC) system on a medium-voltage (MV) network in the case of a line-shield configuration is presented in this paper. An MV cable model in a line-shield configuration is considered together with the power transformers, the signal coupling networks, and the receiving and transmitting line coupling interface of a ST7540 FSK power-line transceiver. Simulations of the complete model of the system under consideration have been carried out for different line lengths, with and without power transformers and derivation branches. The model is validated by experimental tests performed in the laboratory. The measured results confirm the reliability of the model. [ABSTRACT FROM AUTHOR]

This paper reports the results of an experimental study dealing with a commercial Rogowski coil current transducer (RCCT) in the presence of harmonic distortion. The RCCT was observed under two conditions: 1) sinusoidal excitation with frequencies from 50 to 750 Hz and 2) nonsinusoidal excitation using fundamental frequency and one harmonic, with adjustable amplitude and phase shift. The experimental results show only a weak dependence of the harmonic current ratio error and phase displacement on the amplitude and phase shift of the excitation harmonic. The phase displacement is also independent of the conductor position within the Rogowski coil window. An error compensation method, based on the frequency response, was implemented and tested with a distorted waveform. The compensation method allows one to obtain an improvement of the RCCT accuracy class from 1% and 1 ^\circ, in the case of a sinusoidal signal at mains frequency, to 0.05% and 0.05^\circ, both for the fundamental and the distorted signal harmonics. [ABSTRACT FROM PUBLISHER]