Search

WO3-decorated TiO2 nanotube arrays were successfully synthesized using an in situ anodization method in ethylene glycol electrolyte with dissolved H2O2 and ammonium fluoride in amounts ranging from 0 to 0.5 wt %. Anodization was carried out at a voltage of 40 V for a duration of 60 min. By using the less stable tungsten as the cathode material instead of the conventionally used platinum electrode, tungsten will form dissolved ions (W6+) in the electrolyte which will then move toward the titanium foil and form a coherent deposit on the titanium foil. The fluoride ion content was controlled to determine the optimum chemical dissolution rate of TiO2 during anodization to produce a uniform nanotubular structure of TiO2 film. Nanotube arrays were then characterized using FESEM, EDAX, XRD, as well as Raman spectroscopy. Based on the FESEM images obtained, nanotube arrays with an average pore diameter of up to 65 nm and a length of 1.8 μm were produced. The tungsten element in the samples was confirmed by EDAX results which showed varying tungsten content from 0.22 to 2.30 at%. XRD and Raman results showed the anatase phase of TiO2 after calcination at 400 °C for 4 h in air atmosphere. The mercury removal efficiency of the nanotube arrays was investigated by photoirradiating samples dipped in mercury chloride solution with TUV (Tube ultraviolet) 96W UV-B Germicidal light. The nanotubes with the highest aspect ratio (15.9) and geometric surface area factor (92.0) exhibited the best mercury removal performance due to a larger active surface area, which enables more Hg2+ to adsorb onto the catalyst surface to undergo reduction to Hg0. The incorporation of WO3 species onto TiO2 nanotubes also improved the mercury removal performance due to improved charge separation and decreased charge carrier recombination because of the charge transfer from the conduction band of TiO2 to the conduction band of WO3. [ABSTRACT FROM AUTHOR]

High aspect ratio of WO3-loaded TiO2 nanotube arrays have been successfully synthesized using the electrochemical anodization method in an ethylene glycol electrolyte containing 0.5 wt% ammonium fluoride in a range of applied voltage of 10-40 V for 30 min. The novelty of this research works in the one-step formation of WO3-loaded TiO2 nanotube arrays composite film by using tungsten as the cathode material instead of the conventionally used platinum electrode. As compared with platinum, tungsten metal has lower stability, forming dissolved ions (W6+) in the electrolyte. The W6+ ions then move towards the titanium foil and form a coherent deposit on titanium foil. By controlling the oxidation rate and chemical dissolution rate of TiO2 during the electrochemical anodization, the nanotubular structure of TiO2 film could be achieved. In the present study, nanotube arrays were characterized using FESEM, EDAX, XRD, as well as Raman spectroscopy. Based on the results obtained, nanotube arrays with average pore diameter of up to 74 nm and length of 1.6 μm were produced. EDAX confirmed the presence of tungsten element within the nanotube arrays which varied in content from 1.06 at% to 3.29 at%. The photocatalytic activity of the nanotube arrays was then investigated using methyl orange degradation under TUV 96W UV-B Germicidal light irradiation. The nanotube with the highest aspect ratio, geometric surface area factor and at% of tungsten exhibited the highest photocatalytic activity due to more photo-induced electron-hole pairs generated by the larger surface area and because WO3 improves charge separation, reduces charge carrier recombination and increases charge carrier lifetime via accumulation of electrons and holes in the two different metal oxide semiconductor components. [ABSTRACT FROM AUTHOR]

AbstractBackground:Measures of body size at birth are widely used for the evaluation of prenatal growth but limitations exist in their interpretation. Objective:To establish the percentile curves for the six common anthropometric indices (PI: ponderal index, BMI: body mass index, THR: thigh circumference/head circumference ratio, MAC/OFC: mid-arm circumference/head circumference, W/OFC: weight/head circumference, and W/L: weight/length) and determine the best anthropometric index for evaluating intrauterine nutritional status in Chinese neonates. Methods:A prospective cross-sectional anthropometric study was carried out. The anthropometric measurements were performed according to the Hall’s guidelines within 48 h of birth. Results:10,226 infants (5,422 males, 4,804 females) with gestation 28–42 weeks from 12 hospitals were included for analysis. All of the six anthropometric indices correlated well with total skinfold thickness (T-SF, the sum of triceps skinfold thickness and subscapular skinfold thickness; p < 0.0001). Among the six anthropometric indices, W/L showed the highest correlation coefficient with T-SF (r = 0.622; p < 0.0001 in whole group, r = 0.653; p < 0.0001 in preterm infants, r = 0.612; p < 0.0001 in term infants). Conclusion:The present study establishes the gender-specific reference curves for the six important anthropometric indices in Chinese infants. W/L is a readily available index at birth that reflects the intrauterine nutritional state.Copyright © 2008 S. Karger AG, Basel [ABSTRACT FROM AUTHOR]