Search

Voltage rise caused by high levels of distributed generation is manifesting as voltage regulation challenges for many electricity network service providers. In this environment it would be ideal to reduce supply voltage magnitudes, however, many network operators are hesitant to do so due to concerns related to consumer appliance performance at reduced supply voltage magnitudes. Voltage regulation requirements are defined by network standards and network service providers must ensure voltages remain within specified limits. Through an evaluation of domestic appliance performance when supplied at various voltage magnitudes, this paper examines the impact of varying voltage levels on residential appliances. Equipment energy demand, operation and actuation were monitored for each applied voltage magnitude. While no equipment failures were recorded, appliance behaviour varied significantly with applied voltage magnitude. Individual appliance conservation voltage reduction (CVR) factors have also been established. The results highlight the importance of good voltage regulation and provide substantiated appliance performance figures for future studies. The outcomes of this paper allow electricity network service providers to understand the implications of supply voltage magnitude on domestic appliance performance, whether it be understating of the impact of higher voltage magnitudes caused by distributed generation or implications of reducing voltage magnitudes to provide headroom for distributed generation integration. [ABSTRACT FROM AUTHOR]

This paper exploits smart inverters of distributed energy resources (DERs) for the mitigation of fault-induced delayed voltage recovery (FIDVR). According to the IEEE Standard 1547-2018, smart inverters with voltage ride-through and var injection capabilities are promising technologies for mitigating FIDVR. This paper quantitatively investigates the effectiveness of smart inverters for FIDVR from a system-wide perspective. It shows that the penetration of smart inverters and induction motors are important factors affecting mitigation success. In addition, the over-voltages at the end of FIDVR due to load disconnections can be prevented with coordinated control of DERs and automated switching capacitors. The control scheme of smart inverters used for FIDVR is extended from the distributed volt/var droop control to include low- and high-voltage ride-through capabilities. The IEEE 13-bus feeder, the 8500-node test feeder, and the IEEE 390-node low-voltage network test system are used to illustrate the impact of DER penetration. For example, one can determine the residential air conditioner penetration level (for a given system at certain DER penetration level) that makes a system susceptible to FIDVR. The effects of solar intermittency are also studied. [ABSTRACT FROM AUTHOR]

This paper describes a flow control of the dye in the paper mill with the quasi-Z-source indirect matrix converter (QZSIMC) fed induction motor drive. More than a decade the voltage-source inverter (VSI) and current-source inverter (CSI) have been used to control the speed of the induction motor, which in turns controls the flow of dye. Recently, the matrix converter (MC) has been an excellent competitor for the VSI or CSI for its compactness. The voltage transfer ratio of the VSI, CSI, and MC has been limited to 0.866. Thus, the efficiency of these converters is less. To improve the voltage transfer ratio the quasi-Z-source network (QZSN) is to be used between voltage source and indirect MC (IMC). The modification in the shoot-through duty ratio of the QZSN varies the voltage transfer ratio greater than 0.866. Different voltage transfer ratios are needed for different voltage sag conditions. For a variation of the duty ratio of the QZSN, the fuzzy logic controller has been presented. To control the IMC vector control with space vector modulation has been presented. This paper proposes the implementation of QZSIMC adjustable speed drive for the flow control of dye in paper mill during different voltage sag conditions. A 4-kW prototype has been built and the effectiveness of the proposed system is verified with simulation results and experimental setup. Simulation is done in MATLAB, Simulink platform. Experimental setup is done with the aid of a TMS320F2812 (Texas Instrument) processor. The experimental results validate the maintenance of the speed of an induction motor at the set condition, thus controlling the perfect flow of dye in paper manufacturing technology. [ABSTRACT FROM AUTHOR]

This paper presents hybrid design of a Ternary Inverter (TI) circuit by integrating an Ovonic-Threshold-Switching (OTS) based Phase-Change-Memory (PCM) cell between Complementary-Metal-Oxide-Semiconductor (CMOS) transistors. Volatile OTS behaviour of the PCM structure helps to generate the ternary state. Reliability of the proposed TI design has been demonstrated through the Monte-Carlo simulations in Cadence-Spectre simulator incorporating both Process and Mismatch variability at all corners. The proposed inverter cell consumes 10.44 $\mu$ W power and 1.47 ns delay on UMC-180 nm technology node. Moreover to demonstrate the scaling potential, we have simulated the proposed inverter at various technology nodes i.e 180/90/65/28 nm. At advanced feature sizes, power and delay are improved by significant amount. For benchmarking, we have compared the proposed TI design with various state-of-the-art hybrid structures. Furthermore, to demonstrate potential applications, we designed and simulated ternary universal logic gates i.e NAND/NOR. Benefits of the proposed TI in circuit applications are shown through a Ternary Multiplier (TMUL) arithmetic circuit implementation. Finally, a Ternary-Static-Random-Access-Memory (TSRAM) is proposed with two back-to-back connected CMOS-PCM TIs with three bit storing capability. [ABSTRACT FROM AUTHOR]

This paper demonstrates the potential of inverter-based loads to support grid reliability during power system transients thereby enabling reliable integration of renewable energy in power systems. Such loads are referred to in this paper as grid-supportive loads (GSLs). A new GSL model is developed that simulates the transient response capabilities that can be programmed in electronic loads. The model’s design enables it to be easily integrated in widely used commercial power system transient analysis software. Theoretical expressions are derived that explain the workings of the GSL model. The performance, numerical stability, and impact of the GSL model is validated on 9-bus and 2000-bus synthetic power system models using generator tripping and bus fault disturbances. Results on the 2000 bus system show that in the absence of frequency support from wind/solar generation resources, just 20% of loads with grid-supportive capabilities can improve frequency response by up to 2000 MW/0.1 Hz and reduce deviation in frequency at nadir by up to 60% compared to the situation when GSLs are absent. Power system reliability also improves under fault events. It is further shown that GSLs can aid in integrating more renewable generation without degrading the overall transient response of the power system. [ABSTRACT FROM AUTHOR]

In islanded microgrids, distributed generators (DGs) are employed as distributed compensators to improve the power quality on the load side. Due to the access of unbalanced loads, the low-voltage microgrid will naturally exhibit three-phase unbalance, which may cause additional power losses and deteriorate power quality. Therefore, this paper proposes a novel unbalanced-voltage compensation control method based on the Hopf oscillator, which introduces the negative-sequence voltage and current into the traditional Hopf oscillator to achieve the negative sequence voltage droop characteristics. It can not only realize the negative sequence droop control of a single inverter, but it is also capable to support the reactive power automatic distribution between multi-parallel grid-forming inverters. Compared with the traditional unbalanced voltage compensation method based on filtered negative sequence reactive power, the proposed unbalanced voltage compensation method can slightly improve the dynamic response. Experimental results verify the effectiveness of the proposed control strategy. [ABSTRACT FROM AUTHOR]

Voltage-controlled three-phase three-leg inverters are widely applied in various occasions. The inverters are generally switched to the current-controlled mode to limit the fault currents when short-circuit faults happen. Under symmetrical fault, the inverter can be controlled as a symmetrical, three-phase current source. However, the voltage limiting will happen under asymmetrical fault. As a result, the fault phase currents will be distorted and cannot be completely controlled. Considering that the voltage limiting is mainly caused by large load impedance of healthy phase under asymmetrical fault, the voltage limiting is avoided by paralleling the virtual impedance with the output filter capacitor in this paper. As a result, the current limiting loop is not broken and the fault phase currents can be effectively controlled. The implementation of virtual impedance in control system and the influence of virtual impedance on the stability of system are also analyzed in detail in this paper. The theoretical results are validated by experiments. [ABSTRACT FROM AUTHOR]

This paper addresses the frequency oscillation problem in a parallel-inverter-based grid-connected system. Angular frequency interactions between inverters and the grid exhibit various numbers of complicated characteristics that seriously threaten the connected power system's stable operation. This paper proposes a unified frequency oscillation method analysis to investigate the oscillation problem in a multi-VSG grid-connected system. In this method, the power control model of each grid-connected inverter is equivalent to a two-terminal network by analogy method, which can be described as a “current source” connected in parallel with a reciprocal of “admittance” and then joined in series with a joint of “admittance.” Next, considering the influence of grid impedance, the model of the whole grid-connected system is established to reveal the mechanism of multi-VSG angular frequency oscillation. Subsequently, the influence factors of frequency oscillation and its variation law are analyzed through transfer functions, which provide an essential theoretical method for solving the frequency oscillation problem in the current multi-inverter grid-connected engineering application. Finally, we validate the effectiveness and correctness of the small-signal model and the frequency oscillation characteristics by building the MATLAB/Simulink simulation. [ABSTRACT FROM AUTHOR]

Parallel operation of grid-interactive inverters has been continuously gaining attraction, and their contribution to sustaining the host grid stability has become strongly demanded. This paper investigates and discusses the trends in the most recent interconnection grid codes. Grid codes call for simultaneous requirements for the low-voltage ride-through capabilities of parallel operation of grid-interactive inverters as well as their effective asymmetrical voltage support by advanced active/reactive bi-sequence power provision under unbalanced grid faults. Addressing these demands in an optimized way becomes very challenging. This paper thus proposes a new methodology to simultaneously achieve three main objectives: (1) coordination of the asymmetrical ride-through and voltage support capabilities of parallel-operated inverters, (2) maximizing the utilization of each unit and their collective contribution in boosting the positive-sequence voltage and reduction of the negative sequence voltage subject to the constraints from the inverters and the grid, and (3) minimizing the impact of the support on the active power injections. Simulation and experimental results illustrate the effectiveness of the proposed algorithm. [ABSTRACT FROM AUTHOR]

XOR-AND Graphs (XAGs) are an enrichment of the classical AND-Inverter Graphs (AIGs) with XOR nodes. In particular, XAGs are networks composed by ANDs, XORs, and inverters. Besides several emerging technologies applications, XAGs are often exploited in cryptography-related applications based on the multiplicative complexity of a Boolean function. The multiplicative complexity of a function is the minimum number of AND gates (i.e., multiplications) that are sufficient to represent the function over the basis {AND, XOR, NOT}. In fact, the minimization of the number of AND gates is important for high-level cryptography protocols such as secure multiparty computation, where processing AND gates is more expensive than processing XOR gates. Moreover, it is an indicator of the degree of vulnerability of the circuit, as a small number of AND gates corresponds to a high vulnerability to algebraic attacks. In this paper we study the multiplicative complexity of Boolean functions characterized by two particular regularities, called autosymmetry and D-reducibility. Moreover, we exploit these regularities for decreasing the number of AND nodes in XAGs. The experimental results validate the proposed approaches. [ABSTRACT FROM AUTHOR]

The wide variety of inverter control settings for solar photovoltaics (PV) causes the accurate knowledge of these settings to be difficult to obtain in practice. This paper addresses the problem of determining inverter reactive power control settings from net load advanced metering infrastructure (AMI) data. The estimation is first cast as fitting parameterized control curves. We argue for an intuitive and practical approach to preprocess the AMI data, which exposes the setting to be extracted. We then develop a more general approach with a data-driven reactive power disaggregation algorithm, reframing the problem as a maximum likelihood estimation for the native load reactive power. These methods form the first approach for reconstructing reactive power control settings of solar PV inverters from net load data. The constrained curve fitting algorithm is tested on 701 loads with behind-the-meter (BTM) PV systems with identical control settings. The settings are accurately reconstructed with mean absolute percentage errors between 0.425% and 2.870%. The disaggregation-based approach is then tested on 451 loads with variable BTM PV control settings. Different configurations of this algorithm reconstruct the PV inverter reactive power timeseries with root mean squared errors between 0.173 and 0.198 kVAR. [ABSTRACT FROM AUTHOR]

Hybrid high voltage direct current systems utilized for bulk-power transmission have recently attracted more attention. The overhead lines (OHLs) are mainly used for the implementation of such systems due to their outstanding economic advantages. However, OHLs are vulnerable to temporary faults, jeopardizing the safe and reliable operation of the network. The resiliency to the line faults is of considerable significance to the power transmission. This paper proposes a fault property identification strategy based on the Pearson correlation coefficient for the LCC-MMC hybrid HVDC system which can differentiate temporary and permanent faults. To achieve this, a voltage signal is injected into the faulty line by decreasing the firing angles of the LCC-based rectifier. Based on the established OHLs model and the injected signal, an estimated backward travelling wave can be accurately calculated. The fault property is identified by comparing the wave difference of the real backward travelling wave and the estimated backward travelling wave. The proposed strategy has a high accuracy since all influencing factors including the fault resistance, fault distance, and line parameters have been taken into account. Finally, to verify the efficacy of the proposed algorithm, several simulations have been performed using PSCAD/EMTDC. The simulation results show that the proposed algorithm can effectively distinguish the fault property. [ABSTRACT FROM AUTHOR]

Fault response of an inverter based resource (IBR) is dictated by its control scheme, making it markedly different from the response of a synchronous source. This has led to misoperation of distance relays when fed by IBRs. Published literature is mostly focused on changing the control design of inverters, but this approach is not practical, as these controls are proprietary and beyond the reach of utilities. To resolve this issue, this paper proposes a method for a source-agnostic distance relay that works in time-domain. Using only single ended measurements, the relay detects, classifies and locates any fault on the line it monitors. The method does not require any polarization technique. It is shown to work for unbalanced lines of any length, for transmission or distribution system with any number (even 100%) of IBRs, is immune to load encroachment, decaying dc offset and prefault currents. With very limited communication, it is also shown to be immune to fault resistance. [ABSTRACT FROM AUTHOR]

The safety of converters is key to the stable operation of AC/DC hybrid power grids after AC faults. Thyristor valve current is a direct manifestation of the converter observability, but there are no measuring elements inside the converter, so the thyristor valve current can be reflected only indirectly through external electrical quantities. This paper proposes a virtual measurement scheme based on the temporal features of the converter terminal current. First, under the action of the trigger pulse, the polarity characteristics of the AC current and temporal features between the valves are utilized to predictive estimate the valve state. Then, when commutation failures occur and the bypass paths form, the conduction state of valve is constructed based on the relationship between AC and DC current. Last, when the valve is to be shut-off in the bypass path, the blocking state of the valve is corrected based on the unidirectional conductance characteristics of the valve. According to the above analysis, combined with the topological current equation of the converter, the valve current can be calculated in the whole process. Through the simulation of the different valve states and bypass paths and analysis of the field record data, the results show that the valve current can still be accurately calculated based on the virtual measurement scheme. [ABSTRACT FROM AUTHOR]

The hybrid LCC/VSC cascaded HVDC (HC-HVDC) scheme, in which the LCC is adopted as rectifier, and one LCC in series with multiple paralleled VSC based MMCs is adopted as inverter, combines the advantages of both LCC and VSC-MMC technologies. Presently, a HC-HVDC project is planned to deliver the hydro power from Baihetan to Jiangsu in China. One of the major challenges is to suppress the DC overcurrent issue of VSC-MMCs especially under commutation failure condition of LCC at inverter side. Based on Baihetan-Jiangsu project under construction, the model of HC-HVDC system is developed in PSCAD/EMTDC. In the system, the rectifier employs a dual 12-pulse LCC, while the inverter adopts a hybrid scheme, i.e., one LCC converter in series with three paralleled VSC-MMC converters. This paper addresses the main cause and feature of the DC overcurrent, then proposes an overcurrent suppression control method for HC-HVDC system based on fuzzy clustering and identification approach. And the system transient performances with the proposed control approach are evaluated under AC fault conditions. The results show that the proposed approach can not only suppress the DC overcurrent following the commutation failure to a certain extent, but also improve the post-fault recovery performance of the overall system. [ABSTRACT FROM AUTHOR]

Approximate computing (AC) is an emerging technique in arithmetic circuits. In this letter, a new AC-based full adder (FA) circuit is presented with 12 transistors, 150mm]Please confirm or add details for any funding or financial support for the research of this article. -160mm]If you haven’t done so already, please make sure you have submitted a video graphical abstract (GA) for your paper, along with a caption and overlay image. The GA will be displayed on your articles abstract page on IEEE Xplore. Note that captions cannot exceed 1800 characters (including spaces). Overlay images are usually a screenshot of your video that best represents the video. This is for readers who may not have access to video-viewing software. 0.239 $\mu \text{m}^{2}$ of area, and two errors in the outputs. In the proposed FA, the gate diffusion input (GDI) and dynamic-threshold (DT) techniques are applied using the carbon nanotube field-effect transistor (CNTFET) technology. Accuracy metrics, such as normalized mean error distance (NMED) and mean relative error distance (MRED) along with circuitry parameters of power-delay-product (PDP), energy-delay-product (EDP), and power-delay-area-product (PDAP), confirm the efficiency of the proposed FA for complex structures. The proposed FA is embedded in a ripple carry adder (RCA) by various numbers of approximate bits (NABs), and then the accuracy and circuitry parameters are extracted. Compared to the state-of-the-art designs, the high-efficient behavior of the proposed FA is proved when it is used in image processing applications. [ABSTRACT FROM AUTHOR]

In photovoltaic systems, common-mode voltage (CMV) generates leakage current, which shortens the insulation lifespan and causes safety problems. As for neutral-point-clamped (NPC) inverters, zero CMV PWM (ZCMV PWM) can be implemented to eliminate leakage current, but unable to balance neutral-point (NP) voltage in dc side. This article presents a novel modulation technique for NPC PV inverter. The strategy contains ZCMV PWM and another two modulation modes which keeps CMV constant in one switching period, so as to eliminate leakage current. In order to balance NP voltage, NP current is adjusted by selection of optimal modulation mode and the leakage current is still well eliminated during the process of balancing NP voltage. Compared with conventional ZCMV PWM, the proposed scheme can remove both leakage current and NP voltage deviation. The output performance and limitations of the proposed method are also introduced in the paper. Experiments are provided to verify the validity of the proposed method. [ABSTRACT FROM AUTHOR]

Power sharing amongst sources can be improved in an islanded microgrid by utilizing the information of the network’s impedance. In this paper, an impedance based model reference adaptive system (Z-MRAS) scheme is proposed to estimate the impedance angle for converter based distributed generators (DGs) in the islanded mode. The focus is to enhance the proportional apparent power sharing between the DGs operated using generalized droop control (GDC). The performance of GDC depends on the effective tie-line impedance between the DGs and the proposed MRAS scheme provides the feedback of the estimated impedance angle. The accuracy of the impedance angle estimation is established for various tie-line $X/R$ ratios, and this results in enhanced power sharing performance for balanced, harmonic, unbalanced, dynamic and constant power load cases as well as parallel line and underground cable cases. The proposed method is validated through off-line simulations in MATLAB and controller hardware in loop (CHIL) using real time simulator (Opal-RT) including cases of meshed networks and DG plug and play for a modified CIGRE network. [ABSTRACT FROM AUTHOR]

The grid-connected inverter is a key device in the renewable energy power generation system and large-scale energy storage system, which the operational stability and reliability are the basis for the efficient and safe application of electrical energy. A real-time fault diagnosis method of a three-phase for grid-connected application combining a mixed logic dynamic (MLD) model and finitecontrol set model predictive control (FCS-MPC) is proposed. This paper not only realizes the open circuit fault diagnosis and location of the switching devices in the main power circuit, but also discusses the threshold issues and post-fault operations. The advantage of the proposed method is that it directly uses the control data and measurement signals of the controller without extra sensors and calculation, which will shorter the fault diagnosis time and occupy less calculation resource of the main processor. Simulation results illustrate the quickness of the fault identification and accurate position with robustness to the interference of the diagnosis method. Finally, the effectiveness of the diagnosis method was verified by a 1500 W experimental prototype in a laboratory. [ABSTRACT FROM AUTHOR]

Modern energy systems are experiencing the transition towards renewable-powered ones. Some conventional thermal units based on synchronous machines are gradually decommissioned and replaced by power electronics interfaced renewables. Thus, the lack of natural inertia and governor damping, which are the features of synchronous machines, raises significant concern about system frequency stability, including the faster rate of change and lower nadir point of frequency. Meanwhile, with the rapid development of communication and Internet of Things technologies, distributed energy resources can be aggregated as a virtual power plant to help balance real-time electricity demand and supply. However, the capability of utilizing the whole virtual power plant to provide adjustable inertia support has not been explored yet. In this paper, we propose a framework of the synchronous virtual power plant based on grid-forming inverter interfaced distributed energy resources. By coordinating the parameter settings of grid-forming inverters, the virtual power plant provides inertia support. Also, we design an online learning-based parameter settings method that makes the inertia of the virtual power plant adjustable. A case study in IEEE 34 nodes system illustrates the effectiveness of the proposed method. [ABSTRACT FROM AUTHOR]

While high volume of power electronic converters with renewable energy are being integrated into the grid, low system strength of grid causes reduction in system inertia and loss of synchronization with power converters. This paper proposes a novel interactive control scheme of voltage source converter (VSC) connected to weak grid. Firstly, a grid synchronization approach is performed using VSC side voltage transformed on rotating reference frame with respect to grid voltage, which is carried out based on lowest short circuit ratio (SCR) as approved by utilities such as Australian Energy Market Operator’s system strength report. The transformed voltage is then fed into the active power and reactive power control through PLL. Secondly, the grid synchronization approach through PLL is made interactive by adding virtual synchronous generator (VSG) control into the outer loop, which generates virtual inertia to mimic the synchronous generators of a power system. The design of the VSG control parameters is realized based on small signal stability analysis. Furthermore, the control method is evaluated as per the National Electricity Rules clauses S5.2.5.1-S5.2.14 under AEMO and National Service Providers of Australian strict Industry guidelines. The time-domain simulation results are conducted on PSCAD platform. [ABSTRACT FROM AUTHOR]

Reliable power system operation with 100% inverter-based resources (IBRs) is an unsolved and challenging problem. One of the most challenging factors is ensuring power system stability after N-1 contingencies. This paper presents a promising solution using an operator support system (OSS) to enable stable operation of power system with up to 100% IBR generation. The OSS consists of two components. First is dynamic security assessment to evaluate the system resiliency, and identify critical N-1 contingencies that could endanger the system. The second component, as the key technology behind the OSS, is dynamic security optimization (DSO). The DSO optimizes the control parameters of generators and inverters to improve the stability of the system towards the identified N-1 contingencies. The key to system with 100% IBRs, as emphasized in many recent studies, is to establish the grid frequency reference using grid-forming (GFM) inverters. We show through high-fidelity Electro-Magnetic-Transient (EMT) simulations of the future generation models of Hawai‘i Island system with 100% IBR capacity that a system with 100% IBRs can be operated stably with the help of GFM inverters, and appropriate controller parameters can be found by DSO for the inverters. The DSO is verified via 28 critical N-1 contingencies of Hawai‘i Island system identified by Hawaiian Electric. The simulation results verify the effectiveness of DSO, and show significant stability improvement from DSO. [ABSTRACT FROM AUTHOR]

The existing research on voltage-source converter HVDC (VSC-HVDC) system stability mostly focuses on small-signal stability analysis methods. However, when large-signal disturbances occur, the intrinsic nonlinearity of the VSC-HVDC system becomes inevitable so that the small-signal studies are no longer valid. In this paper, a large-signal stability analysis method of the VSC-HVDC system is proposed based on the estimation of domain of attraction (DOA). This method can not only analyze the asymptotic stability of the operating point, but also answer the question of how large deviations from the operating point can be tolerated by the system. By using Takagi-Sugeno (T-S) fuzzy model and Lyapunov stability theorem, the DOA of the VSC-HVDC System at the operating point is estimated, and the large-signal stability of VSC-HVDC System is analyzed. On this foundation, the influence of system parameters on the large-signal stability is studied. The results can be used to guide the adjustment of system parameters to solve the problem of system instability. The time-domain simulations conducted in Matlab/Simulink are used to test the stability of the system under large-signal disturbance in the range of DOA. The simulation results verify the feasibility and effectiveness of the proposed method. [ABSTRACT FROM AUTHOR]

This paper investigates the dynamic voltage support (DVS) from inverter-based resources (IBRs) under voltage sags to enhance the low-voltage ride-through performance. The DVS problem is formulated as a nonconvex optimization program that maximizes the positive-sequence voltage magnitude at the point of common coupling (PCC) subject to the current, active power, and synchronization stability constraints. Then, we perform the optimality analysis to explore the global optimum analytically. It is found that the unique global optimum has three scenarios/stages (S1–S3), which depends on the specific relationship among grid voltage, grid strength, and physical limits of IBRs. The explicit closed-form solutions in S1 and S3 are derived, and the optimality conditions (an implicit solution) of S2 are provided, which guarantees the global optimality and enables the compatibility with fast real-time control. Finally, we implement the optimum with a grid-connected single-stage photovoltaic (PV) power plant by integrating a DVS controller. Dynamic simulations are carried out under different scenarios to test our proposal. The robustness against model errors is also discussed. [ABSTRACT FROM AUTHOR]

Miniaturization and low cost contribute to the development and popularization of wireless power transfer (WPT). Reducing the number of power conversion stages can reduce the volume and cost of the WPT converter, and even make it possible to improve the efficiency. A single-stage WPT converter with constant current (CC) and constant voltage (CV) output and its asymmetric modulation method are proposed in this paper. A direct AC-AC converter is applied to the primary side of the WPT converter to directly convert line-frequency AC to high-frequency AC. The applied direct AC-AC converter that can replace the commonly used multi-stage primary converter reduces the number of circuit devices, thereby reducing the volume and cost of primary converter. The proposed WPT converter can realize zero voltage switching (ZVS) and power factor correction (PFC). In order to achieve CC and CV output, a switchable hybrid compensation topology is applied to the proposed WPT converter. A 720-W experimental prototype was manufactured to verify the rationality of the proposed WPT converter and the correctness of the theoretical analysis. [ABSTRACT FROM AUTHOR]

Most microgrid protection schemes found in published literature suffer from a lack of generality in that they work well for the assumed topology, including type and placement of sources. Other generic protection schemes tend to be too complicated, too expensive, or both. To overcome these drawbacks, a topology-agnostic, scalable, and cost-aware protection based on fundamental principles that work in the presence of high penetration of inverter-based resources (IBRs) is developed and tested in this paper. The protection system also implements stable automatic reconfiguration of the healthy sections of the system after clearance of fault, thus increasing resilience by self-healing. To achieve this ambitious goal, stable inverter models are developed that operate in unbalanced networks in grid-connected and islanded modes, even with 100% IBRs, share power without conflicting controls, and can ride through faults while limiting fault currents. The scheme is tested for primary and backup protection and reconfiguration on the IEEE 123-node feeder in grid-connected and islanded modes with 15 IBRs connected to the system. [ABSTRACT FROM AUTHOR]

The advancements in smart grid technologies had brought forth the prospect of self-healing distribution grid through intentional islanding, aided by the steadily rising penetration of inverter-based distributed generations (IBDGs). Adaptive protection is the key enabler for this resilient grid architecture. For cost-effectiveness, overcurrent relays (OCRs) with adaptive features had been proposed, often with the sensitivity problem due to low short-circuit current magnitude from the IBDG taken into consideration and largely addressed. However, apart from this widely discussed sensitivity problem, there is an underlying issue on selectivity of the OCR which is frequently disregarded when designing an adaptive overcurrent protection scheme for IBDG dominated microgrid. This selectivity problem is mainly caused by the current diversion to load during fault, which is often disregarded when performing OCR grading for a conventional grid. In this paper, this selectivity problem of the OCR is discussed in depth through a comparative study of conventional grid and a modern IBDG dominated grid. The coordination time interval margin violations problems are demonstrated through theoretical calculations and real-time hardware-in-the-loop experiments. This research aims to provide better insights into the selectivity problem as a step towards achieving a cost-effective yet reliable overcurrent-based adaptive protection for IBDG dominated microgrid. [ABSTRACT FROM AUTHOR]

Although the harmonics interaction plays a vital role in causing commutation failure (CF) in an ultra HVDC (UHVDC) system with hierarchical connection, it has not been sufficiently considered in previous work. In this paper, the electric interaction among the inverter valves of the UHVDC system with hierarchical connection during receiving system fault transient process is demonstrated. Moreover, the mechanism of CFs in UHVDC system with hierarchical connection is also investigated via the analysis of harmonics interaction. After the AC fault occurs, the appearance processes of the local commutation failure (LCF) and concurrent commutation failure (CCF) are divided into several stages and interpreted by schematic diagrams. And the characteristics of each stage are also concluded. In addition, a coordinated CF prevention scheme based on harmonics and DC current detection is proposed to mitigate the CFs in UHVDC system with hierarchical connection. Finally, the effectiveness of the proposed scheme is verified via a $\pm 1100$ kV UHVDC transmission system under various short circuit ratio values and AC-side coupling strengths. [ABSTRACT FROM AUTHOR]

This paper presents a new voltage support (VS) strategy for photovoltaic (PV) systems based on voltage sensitivity analysis to enhance the dynamic voltage stability (DVS) of islanded microgrids (MGs). Every network contains different characteristics. In particular, MGs have unique features compared to utility grids such as high resistance to reactance ratio (R/X). Consequently, injection of both active and reactive current is likely to improve the DVS of the islanded MG. Therefore, instead of engaging the entire capacity to reactive current injection which is performed in conventional voltage support strategy, both the active and reactive current is injected in the proposed strategy. On contrary, without considering the fact that each network contains distinctive characteristics, other strategies with both active and reactive current injection provide fixed active and reactive current which are uniform for all networks. To convey the network distinctive features on VS strategy, voltage sensitivity subject to active and reactive current injection is used in the proposed strategy. As a consequence, unlike other fixed active and reactive current strategies, the proposed strategy provides unique combination of active and reactive current for every network. The concept and derivation of the proposed strategy is clearly described. Network sensitivity analysis is carried out to determine the voltage sensitivity coefficients. The effectiveness of the proposed strategy is theoretically demonstrated and also compared with other strategies. Case studies are carried out on two different islanded MGs. The results show that the proposed voltage support strategy is capable of enhancing the DVS of islanded MGs by mitigating a possible instability, and by restoring the voltage faster than other strategies. [ABSTRACT FROM AUTHOR]

Line-commutated converters are extensively used as the interface between ac grids and classic HVDC systems. At the inverter side, commutation failure of switches is one of the most common faults that can pose threats to the system operation. Practical and reliable study of such phenomena relies on accurate and efficient converter models for simulations. Recently, a parametric average-value model (PAVM) has been presented for ac–dc rectifiers, which considers the internal faults of the converter. In this paper, the PAVM methodology is extended to the dc–ac inverter systems, including the commutation failure of switches. The proposed PAVM also augments an automatic fault detection technique to determine the faulty switches. Using comprehensive simulation studies, the developed model is verified to accurately predict the commutation failure of switches and reconstruct the waveforms consistent with the detailed switching models of inverters while being computationally more efficient. The proposed PAVM is envisioned to be an efficient and accurate asset for simulation of HVDC systems and inevitable when faults of switches need to be considered. [ABSTRACT FROM AUTHOR]

In this paper, we investigate the control of inverter-based resources (IBRs) for optimal voltage unbalance attenuation (OVUA). This problem is formulated as an optimization program under a tailored dq-frame, which minimizes the negative-sequence voltage at the point of common coupling (PCC) subject to the current, active power, synchronization stability, and feasibility constraints. The program is inherently nonconvex and intractable. So, to guarantee the optimality, a rigorous optimality analysis is performed by leveraging analytical optimization. The analysis is divided into two cases: full mitigation of VU and partial attenuation of VU. For the former case, we directly solve the original program since the resultant VU is immediately deducible. For the latter one, directly solving the problem becomes very hard. Thus, we reformulate the program into an equivalent but more tractable form under certain conditions, by which the analytical optimum can be derived. It is found that the optimum trajectory has three stages (O1–O3), depending on two critical boundary conditions (C1 and C2). We implement the optimum with a photovoltaic (PV)-storage system by developing an OVUA controller. The proposed approach is demonstrated by dynamic simulations under different VU conditions and is compared with several existing practices. Finally, we discuss the extension of the proposed solution in a multi-IBR system. [ABSTRACT FROM AUTHOR]

This paper presents a hierarchical control system to mitigate the variability of solar photovoltaic (PV) power plant and provide ancillary services to the electric grid without the need for additional non-solar resources. With coordinated management of each inverter in the system, the control system commands the power plant to proactively curtail a small fraction of its instantaneous maximum power potential, which gives the plant enough headroom to ramp up production from the overall power plant, for a service such as regulation reserve. This control system is practical for continuously changing cloud cover conditions in partially cloudy days. A case study from a site in Hawaii with one-second resolution solar irradiance data is used to verify the efficacy of the proposed control system. The proposed control algorithm is subsequently compared with the alternative control technology from the literature, the grouping control algorithm; the results show that the proposed hierarchical control system is over 10 times more effective in reducing generator mileage to support power fluctuations from solar PV power plants. [ABSTRACT FROM AUTHOR]

In distribution networks with a high penetration of photovoltaic (PV), a coordination between reactive power compensation (RPC) of PV inverter and active power compensation (APC) of battery energy storage system (BESS) is always used in voltage regulation (VR). Since using a periodical VR inevitably increases communication utilization, how to design a new event-triggered one to reduce communication burden while achieving comprehensive voltage governance with the required minimum BESS sizing? Therefore, an event-triggered hybrid VR method is proposed in this paper. Firstly, an event-triggered communication is designed based on the changes in bus voltage and sensitivity, thereby defining all operating instants into transmission and ordinary sampling types. For the voltage violation issue at the transmission instants, a network-wide coordinated proportional RPC-APC is then designed, which keeps constant during one transmission interval. For the additional voltage fluctuation at the ordinary sampling instants in the interval, a local RPC-APC is additionally designed to yield a fast suppression without using any communication. In addition, the required minimum BESS sizing is obtained by calculating the total APC for VR requirement, which gives a reference in configuring BESS. Finally, the case study is conducted to demonstrate the effectiveness of this method. [ABSTRACT FROM AUTHOR]

When faults occur in the microgrids, high frequency transients will be superimposed on the system currents and voltages. The magnitude of those transients will attenuate as it encounters the discontinuity points in the network such as busbars, or any other impedance discontinuity points. This phenomenon can also be quantified by wavelet energy, which provides a useful tool to detect faults and locate the faulted feeder in the microgrid. In this paper, a novel protection scheme based on the transient wavelet energy of the superimposed current extracted by the Maximal Overlap Discrete Wavelet Transform (MODWT) algorithm is developed to detect faults and locate the faulted feeder in microgrids. Compared with existing protection schemes, the proposed protection scheme has the advantage of being largely immune to the changes in system fault level, fault types and positions, microgrid operating status and the control strategies deployed on the inverters, while presenting much lower requirement on the sampling frequency (10 kHz) compared with travelling wave-based methods. Unlike the conventional differential protection, the proposed scheme does not require synchronized measurement or high bandwidth communication channels, and thus, it can be considered as an economical and promising solution for microgrids. [ABSTRACT FROM AUTHOR]

This paper presents a dual active bridge (DAB) converter with reactive power control capability (Q-capability) for a battery energy storage system (BESS) or an electric vehicle (EV) to deliver vehicle-to-home (V2H) and vehicle-to-grid (V2G) services. The DAB topology is preferable for EV charging systems due to its galvanic isolation and bidirectional power flow capabilities. However, this topology increases reactive current peak and loses zero voltage switching (ZVS) operation at light loads if it is not controlled with improved modulation strategies and proper Q control. This paper proposes a mixed modulation method and a reactive power optimization (RPO) algorithm based on power system load flow concepts. Due to the complexities associated with the analytical solution using time domain analysis, this paper develops detailed universal expressions of a DAB converter using the harmonic analysis method. Analytical identification of ZVS boundaries and DSP implementation of the RPO algorithm become easier with these universal expressions. Multiple modes analysis for different operational states is no longer required. Simulation results have been shown for different modulation strategies of the DAB converters. The theoretical analysis of modulation strategies, RPO algorithm and ZVS operation are validated by experimental results on a DAB prototype. Results show that the proposed control strategy reduces the reactive power and provide ZVS operation over a wide ranges of voltages. [ABSTRACT FROM AUTHOR]

The commutation failure (CF) is the most common fault in line-commutated high voltage direct current (LCC-HVDC) systems that may lead to the transient overvoltage in the sending-side system. In the worst condition, the CF may lead to large-scale wind turbine tripping. To resolve this problem, the mathematical relationship between the reactive power consumed by the rectifier and DC voltage, DC current is derived. Then, a transient overvoltage calculation method is proposed in this paper. Furthermore, the mechanism of transient overvoltage caused by the CF is analyzed; it is revealed that the reason for three times transient overvoltage is the rapid decrease of the reactive power consumed by the rectifier during the CF and the recovery period from the CF. This paper proposes a constant reactive power control (CRPC) to inhibit transient overvoltage of the sending-side AC system. The proposed CRPC can increase the reactive power consumed by the rectifier, reduce the exchange reactive power between AC and DC systems, and suppress the transient overvoltage. A simulation model in PSCAD serves to verify the proposed CRPC on the transient overvoltage suppression in the situation of different fault types, fault duration, fault severity and short circuit ratio (SCR). [ABSTRACT FROM AUTHOR]

Inverter-based resources respond differently than synchronous generation sources during power system faults, challenging line protection reliability. To understand the reliability challenges, Sandia National Laboratories and North American Electric Reliability Corporation (NERC) led a collaborative study with four inverter manufacturers (mix of Type 3 Wind, Type 4 Wind, and PV Solar) and two North American protective relay manufacturers. As part of this study, an electromagnetic transients program (EMTP) with “real-code” models representing inverter firmware was used to investigate the protective relay response to faults on the modeled power system with the different inverter types. The currents and voltages obtained from the study were then played back through line relay hardware with settings typical of systems with conventional generation. The protective relays exhibited the expected reliability challenges but provided insight into the behavior of inverter-based resources during power system faults. In this paper, we share some of the challenging cases with the responses of the different line protection schemes. Using insight from the various event records, Part II of this paper shows how relay settings can be modified to obtain a substantial improvement in reliability. [ABSTRACT FROM AUTHOR]

An inexact 6-transistor full adder (FA) cell is presented. It is low-power and gives full-swing outputs because of the applied gate diffusion input (GDI) along with the dynamic threshold (DT) techniques. The FA which has three errors is used in a 10-transistor inexact 4:2 compressor based on the stacking circuit idea. The implementation by a 16-nm carbon nanotube field-effect transistor (CNTFET) technology shows a small area of 0.027 and $0.045~\mu \text{m}^{\mathrm{ 2}}$ for the FA and compressor, respectively. A new approximate sum of absolute differences (SADs) block is presented by the FA and compressor. The average power, power-delay-product (PDP), and peak signal-to-noise ratio (PSNR) of the SAD are 6.80 mW, 33.86 nJ, and 42.98 dB, respectively, which confirm its efficiency for bioimages difference detection. [ABSTRACT FROM AUTHOR]

The strength concept is an important tool for voltage stability evaluation of emerging hierarchical-infeed LCC-UHVDC (HIDC) systems. However, the complex inter-inverter interactions in such systems have caused significant difficulties for the strength assessment. This makes the accuracy of earlier strength assessment indices limited due to empirical analysis rather than rigorous theoretical reasoning. Thus in this paper, the hierarchical-infeed voltage interaction factor (HVIF) index is firstly utilized to quantitatively depict the complex inter-inverter interactions in HIDC systems. The use of the HVIF enables these interactions to be effectively incorporated into the subsequent strength assessment by proposing the hierarchical-infeed interactive effective short-circuit ratio (HIESCR) strength index. The critical HIESCR (CHIESCR) defined to delineate the voltage stability limit also evaluates to consistently 1.0 such that the distance between the HIESCR and CHIESCR is naturally an accurate stability margin. Since the HIESCR is developed based on the rigorous theoretical reasoning, it is more accurate than earlier indices for voltage stability evaluation. Moreover, the parametric dependence analysis of the HIESCR versus various system parameters and rated operation variables is conducted. This offers a comprehensive perspective for better understanding of the strength variation characteristics. Finally, case study in the modified IEEE 118-bus system validates the HIESCR. [ABSTRACT FROM AUTHOR]

Optimal protection coordination is usually solved for the original network topology with all lines, loads, and generation intact. However, power grids may experience contingencies due to transient events, e.g., generation or line outages. Low fault currents of inverter-interfaced distributed generators (IIDGs) necessitate a sensitive and reliable protection scheme. This paper proposes a protection scheme for islanded microgrids powered by droop-based IIDGs. The protection scheme utilizes virtual impedance-fault current limiters to limit IIDGs fault currents and achieve protection coordination. A two-stage method for optimal protection coordination (OPC) of directional overcurrent relays (DOCRs) is devised. In Stage I, relays short-circuit currents are calculated. Then, constraints on the operation times of primary and backup DOCRs are formulated for the islanded topology and each possible topology following an N-1 contingency. Lastly, in Stage II, the OPC problem is formulated as a constrained nonlinear programming problem and solved to obtain the optimal DOCRs settings. A radial test microgrid that is part of a Canadian urban distribution system is used to ensure the success of the proposed OPC method. [ABSTRACT FROM AUTHOR]

Behind-the-meter battery energy storage is used to mitigate non-dispatchability of customer-owned renewable sources. While serving their owners’ objectives, their underutilized capacities can be used to provide grid services to justify their cost. However, the integration of these resources extends the size and complexity of the network operation problem, imposing a processing burden on the central control system. In this paper, an agent-based distributed control framework is proposed that enables utilizing of the underutilized behind-the-meter capacities. In this framework, while the prosumer agents initially schedule their resources for daily cost management, a local customer aggregator agent performs day-ahead active and reactive power control on the underutilized behind-the-meter batteries to provide multiple grid services. A novel grouping algorithm is developed based on voltage sensitivity and a modified $k$ -means clustering method to assign customer groups to the local agents and establish the network subsystems. Mixed-integer linear programming is used to model and solve multiple optimization problems. The proposed framework is applied to the 123-bus distribution network. The simulation results show its effectiveness in terms of complexity and optimality, compared to the central control approach in allocating the unused behind-the-meter resources for two common industry needs: network bottleneck congestion relief and grid-edge voltage support. [ABSTRACT FROM AUTHOR]

In this paper, a new pilot protection scheme for AC line connected to LCC-HVDC inverter based on composite-mode model is proposed. First, taking commutation failure into consideration, 1-mode and 2-mode equivalent instantaneous models of inverter in different operating conditions are built. Second, according to the equivalent instantaneous inductances of inverter in different combinations of operating conditions, the equivalent models of inverter are summarized into 4 operation states. Then, the 1-mode and 2-mode equivalent models are combined to establish the composite-mode model of AC/DC hybrid system. And then, using multi-time section information, the instantaneous inductances of backside composite-mode model are calculated. Thus, protection criterion is constructed on the difference between composite-mode models of in-zone faults and that of out-of-zone faults for fault locating. Finally, RT-LAB simulation tests show that, the proposed method offers high sensitivity and reliability, unaffected by commutation failure. [ABSTRACT FROM AUTHOR]

The neutral grounding method is one of the crucial technologies used to ensure the safe and stable operation of distribution networks. With the development of power electronics-based devices, the application of highly controllable inverters to grounding systems has become a new research direction. In this review paper, based on the summary and analysis for the research status, the flexible grounding system is systematically classified according to its control strategy and structure. And then, the following core technologies are summarized: faulted line selection, current component detection, high-resistance ground identification, ground parameter measurement, neutral point voltage control, and fault location. Subsequently, deficiencies of flexible grounding systems are summarized from the following four perspectives: reliability, accuracy, speed, and stability. Finally, some discussions and recommendations for future development and research direction are presented. Especially, the reliability-enhanced hybrid grounding system that combines active inverters and low resistance for high-resistance ground faults is recommended. This paper provides a systematic literature review of the crucial technologies for flexible grounding systems and can be used as a technical reference for future research. [ABSTRACT FROM AUTHOR]

Aggressive technology scaling makes modern advanced SRAMs more and more vulnerable to soft errors such as single-node upsets (SNUs) and double-node upsets (DNUs). This paper proposes two SRAM cells; the first one is called Quadruple Cross-Coupled SRAM (QCCS) and the second one is called Sextuple Cross-Coupled SRAM (SCCS). The QCCS cell comprises four cross-coupled input-split inverters to keep stored values, and provides self-recoverability from SNUs at low cost. To improve reliability, the SCCS cell uses six cross-coupled input-split inverters to construct a large error-interceptive feedback loop and hence robustly keep stored values. The SCCS cell can self-recover from all possible SNUs and one part of DNUs; for remaining DNUs, a node-separation mechanism is used to avoid their occurrence. Simulation results demonstrate the robustness of the proposed cells. Moreover, compared with the state-of-the-art hardened cells, i.e., NASA13T, RHBD12T, We-Quatro, Zhang14T, QUCCE12T, DNUSRM, QCCM10T, QCCM12T, S4P8N, and S8P4N, the QCCS cell reduces read access time by 17%, write access time by 19%, power dissipation by 4% and silicon area overhead by 10% on average, while the SCCS cell reduces read access time by 44% as well as write access time by 13% on average at the cost of moderate increase in power dissipation and silicon area overhead. [ABSTRACT FROM AUTHOR]