Search

This study investigated six-month outcomes of first models of ascending aortic replacement. The molds used to produce the Biotube were implanted subcutaneously in goats. After 2–3 months, the molds were explanted to obtain the Biotubes (inner diameter, 12 mm; wall thickness, 1.5 mm). Next, we performed ascending aortic replacement using the Biotube in five allogenic goats. At 6 months, the animals underwent computed tomography (CT) and histologic evaluation. As a comparison, we performed similar surgeries using glutaraldehyde-fixed autologous pericardial rolls or pig-derived heterogenous Biotubes. At 6 months, CT revealed no aneurysmalization of the Biotube or pseudoaneurysm formation. The histologic evaluation showed development of endothelial cells, smooth muscle cells, and elastic fibers along the Biotube. In the autologous pericardium group, there was no evidence of new cell development, but there was calcification. The histologic changes observed in the heterologous Biotube group were similar to those in the allogenic Biotube group. However, there was inflammatory cell infiltration in some heterologous Biotubes. Based on the above, we could successfully create the world's first Biotube-based ascending aortic replacement models. The present results indicate that the Biotube may serve as a scaffold for aortic tissue regeneration. [ABSTRACT FROM AUTHOR]

Objective: We developed an effective hemostatic method using Hydrofit® and a hemostatic gelatin sponge (Spongel®). We evaluated the hemostatic effect in comparison to the conventional silicone sheet method. Methods: A simulated circuit was created using the pump of a Nipro ventricular assist system and a prosthetic graft. A hole was made in the graft by a needle and three hemostatic methods were applied: the silicone sheet method (SS) using Hydrofit® and a silicone sheet, the bread and butter method (BB) using Hydrofit® and a gelatin sponge instead of a silicone sheet, and French toast method (FT) using Hydrofit® and a gelatin sponge over which water was poured before compression. The amount of leakage before and after the application each of the methods was measured according to the compression time. Results: In the 60 s compression, the amount of leakage after SS, BB, and FT was 0.4 ± 0.8, 0.2 ± 0.6, and 0 ± 0.0 ml, respectively, and FT showed no leakage. In the 30 s compression, the amount of leakage after SS, BB, and FT was 14.2 ± 27.9, 1.0 ± 3.2, and 7.8 ± 22.6 ml, respectively, and did not differ to a statistically significant extent. Conclusions: The method of combining Hydrofit® and Spongel® could obtain reliable hemostasis in 60 s. [ABSTRACT FROM AUTHOR]

We developed a surgical hemostatic film using Hydrofit® (Hydrofit® film). This film is prepared by reacting Hydrofit® with water in advance, and it can be used in the same way as an accessory silicone sheet. In addition, unlike the silicone sheet, there is no need to remove the Hydrofit® film from the body. In the present study, we describe the hemostatic effect of our new method using Hydrofit® film. We created a pulsatile flow circuit model using a ventricular assist device and a vascular graft. The circuit was filled with water, and the systolic pressure was adjusted to ≥ 130 mmHg. The artificial blood vessel was punctured by an 18-G needle. Operations to prevent water from leaking were attempted through either a conventional method using a silicone sheet or our new method using Hydrofit® film. In the 180-s trial, 14 attempts (93.3%) with the Hydrofit® film were successful. In the silicone sheet group, 13 attempts (86.7%) were successful before the silicone sheet was peeled off, and hemostasis was maintained in 10 (66.5%) cases after the silicone sheet was removed. After short-duration hemostasis for 60 s, good waterproofing was obtained in the Hydrofit® film group (success in 17 cases [85%]). In contrast, in the silicone sheet group, 10 attempts (50%) were successful before the silicone sheet was peeled off, and hemostasis was maintained in only 7 (35%) cases after the silicone sheet was removed. Hydrofit® film showed good hemostatic performance in the pulsatile flow circuit model. [ABSTRACT FROM AUTHOR]