Search

In this paper, we propose a simple method for the modification of the unit cells in the lattice metamaterials that provides an improvement of their impact strength. The idea is based on the introduction of small mutual offsets of the interconnected struts inside the unit cells. In such way, the joints between the struts become asymmetric and the overall geometry of the unit cells can be defined as the quasi-cubic with the axis of chirality. Considering four types of cubic lattices with BCC, BCT, FCC and octahedron structures, we modified their geometry and investigated the influence of the offsets and the unit cell size on the overall performance in static and dynamic tests. From the experiments we found that the small offsets (less than the strut diameter) can allow to increase the impact strength of 3d-printed polymeric specimens in 1.5–3 times remaining almost the same density and static mechanical properties. Based on the numerical simulations, we show that the explanation of the observed phenomena can be related to the increase of plastic deformations and damage accumulation in the unit-cells with asymmetric joints leading to the transition from the quasi-brittle to the ductile type of fracture in tested specimens. [ABSTRACT FROM AUTHOR]

In this paper, we propose a simple method for the modification of the unit cells in the lattice metamaterials that provides an improvement of their impact strength. The idea is based on the introduction of small mutual offsets of the interconnected struts inside the unit cells. In such way, the joints between the struts become asymmetric and the overall geometry of the unit cells can be defined as the quasi-cubic with the axis of chirality. Considering four types of cubic lattices with BCC, BCT, FCC and octahedron structures, we modified their geometry and investigated the influence of the offsets and the unit cell size on the overall performance in static and dynamic tests. From the experiments we found that the small offsets (less than the strut diameter) can allow to increase the impact strength of 3d-printed polymeric specimens in 1.5–3 times remaining almost the same density and static mechanical properties. Based on the numerical simulations, we show that the explanation of the observed phenomena can be related to the increase of plastic deformations and damage accumulation in the unit-cells with asymmetric joints leading to the transition from the quasi-brittle to the ductile type of fracture in tested specimens. [ABSTRACT FROM AUTHOR]

Copyright of Periódico Tchê Química is the property of Grupo Tche Quimica and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

The article presents the results of a study of the contact zone of a thin-walled cylindrical shell located between two parallel rigid plates. The shell under consideration was located with various gaps from the rigid plate and was subsequently subjected to internal pressure. In the course of such a study, experimental, numerical and analytical estimates of the contact zone width were obtained depending on the discharge pressure. The obtained numerical and analytical estimates are tested with experiment. To study the width of the contact zone, depending on the gap, a testing workbench was used. The problem of numerical and analytical modelling was solved by the finite element analysis in the Ansys Workbench system. The solution to transcendental equation was found numerically using the Newton-Raphson method. As a result of experimental, numerical and analytical studies, results were obtained for a plane-oval shell with gaps of 0.5 mm, 1 mm and 2 mm, depending on the applied pressure. [ABSTRACT FROM AUTHOR]

Copyright of Periódico Tchê Química is the property of Grupo Tche Quimica and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

Copyright of Periódico Tchê Química is the property of Grupo Tche Quimica and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

Copyright of Periódico Tchê Química is the property of Grupo Tche Quimica and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)