Search

The shift from fossil fuels to renewable energy systems represents a pivotal step toward the realization of a sustainable society. This study aims to analyze representative scientific literature on eco-sustainable energy production in the healthcare sector, particularly in hospitals. Given hospitals' substantial electricity consumption, the adoption of renewable energy offers a reliable, low-CO2 emission solution. The COVID-19 pandemic has underscored the urgency for energy-efficient and environmentally-responsible approaches. This brief review analyzes the development of experimental, simulation, and optimization projects for sustainable energy production in healthcare facilities. The analysis reveals trends and challenges in renewable energy systems, offering valuable insights into the potential of eco-sustainable solutions in the healthcare sector. The findings indicate that hydrogen storage systems are consistently coupled with photovoltaic panels or solar collectors, but only 14% of the analyzed studies explore this potential within hospital settings. Hybrid renewable energy systems (HRES) could be used to meet the energy demands of healthcare centers and hospitals. However, the integration of HRES in hospitals and medical buildings is understudied. [ABSTRACT FROM AUTHOR]

Air-source heat pumps are strongly influenced by outdoor conditions, it is expected that ongoing climate changes may impact their operation. This paper presents a predictive analysis of the behaviour of air-source heat pumps in two cities with extremely cold and warm climates in the short, medium, and long term. The seasonal coefficient of performance and heat pump seasonal energy efficiency index are evaluated over the years, considering climate change for both locations. Climate change will shorten the winter period and prolong the summer. In winter, this results in a slight softening of the seasonal coefficient of performance and a reduction in operating hours. In summer, there is a slight increase in seasonal energy efficiency ratio values and hours of operation. The work highlights how the performance of the air-source heat pump, on average, will improve in winter due to an average increase in temperature. Heat pumps are expected to be used in the future and in geographical areas where they are not currently used due to the extreme winter temperatures. [ABSTRACT FROM AUTHOR]

Hybrid renewable energy systems are an optimal solution for small energy communities' energy supply. One of the critical issues is the strong correlation of these systems with outdoor climatic conditions. The goal is to make local communities increasingly energy independent. To this end, an in-depth analysis of the behaviour of hybrid photovoltaic (PV)–wind systems powering small office communities in 48 locations around the world characterized by widely varying climates was conducted. System sizes, assumed to be stand-alone or grid-connected, were varied, for a total of 343 system power configurations. Highest satisfied load fraction (SLF) values are obtained with a significant predominance of PV over wind; the trend is more pronounced in dry and continental climates (zones B and D according to the Köppen climate classification). The utilization factor (UF) values of 1 are rarely reached and never in the wind-only or PV-only configurations. In all climates, the grid energy interaction factor (GEIF) values of zero are never reached but come very close. The benefit-cost ratio (BCR) of grid-connected systems is significantly higher than stand-alone systems. [ABSTRACT FROM AUTHOR]

This work aims to assess the impacts of climate change on photovoltaic (PV) electricity in two Italian cities, with different latitudes and Köppen–Geiger climate classifications. This was undertaken using the recent EURO-CORDEX set of high-resolution climate projections and PV power generation models, implemented on TRNSYS software. Data for two variables (surface air temperature and solar radiation) were analysed over a long period from 1971 to 2100. For future periods, two of the Representative Concentration Pathway scenarios (RCP4.5 and RCP8.5) used in the Intergovernmental Panel on Climate Change Fifth Assessment Report were considered. In both RCP scenarios and both locations, it is estimated that the yearly PV energy produced in the future period will not undergo significant variations on average given that the rate of decrease is foreseen almost constant; instead, a slight reduction in the PV energy was detected in the past period. It can be concluded that the PV market in Italy will grow in the next years considering that the reduction in the foreseen PV purchase costs will be also supported by the slight positive effect of climate change on PV manufacturability. [ABSTRACT FROM AUTHOR]

Energy storage makes energy continuously available, programmable, and at power levels different from the original intensity. This study investigates the feasibility of compressed-air energy storage (CAES) systems on a small scale. In addition to the CAES systems, there are two TES (thermal energy storage) systems for the recovery of calories and frigories. The micro-CAES + TES system is designed for a single-family residential building equipped with a photovoltaic system with a nominal power of 3 kW. The system is optimized as a potential alternative to battery storage for a typical domestic photovoltaic system. The multi-objective optimization analysis is carried out with the modeFRONTIER software. Once the best configuration of the micro-CAES + TES system is identified, it is compared with electrochemical storage systems, considering costs, durability, and performance. The efficiency of CAES (8.4%) is almost one-tenth of the efficiency of the most efficient batteries on the market (70–90%). Its discharge times are also extremely short. It is shown that the advantages offered by the application of mechanical accumulation on a small scale are mainly related to the exploitation of the thermal waste of the process and the estimated useful life compared to the batteries currently on the market. The studied system proves to be non-competitive compared to batteries because of its minimal efficiency and high cost. [ABSTRACT FROM AUTHOR]

This study presents the retrofit acoustic dq1esign of the Italian theatre "Cavallino Bianco". In its historical configuration, the hall had a curved roof with a pressed-plant fiber ceiling, which was demolished and replaced with a wooden roof without a false ceiling, leading to an increase in volume and a worsening of the reverberation time. This study proposed the realization of a wave ceiling and the application of sound-absorbing and reflecting panels on the walls, which have already been implemented. These modifications have affected the acoustic characterization of the theatre, as shown both through on-site measurements during the main construction phases and through numerical simulations. The reverberation time, clarity index, and speech transmission index (STI) are evaluated considering all the variations in the hall over different construction times, and the optimal solution is identified with regard to different specific uses. The final configuration with the new roof, by reducing the volume of the hall and using sound-absorbing materials, significantly reduces the reverberation time (e.g., at 2000 Hz, this reduction is from 2.33 to 1.47). In addition, the hall at full capacity with chairs and people shows evident improvement in terms of the clarity index, allowing the theatre to be used for a wide range of musical genres such as instrumental, symphonic, and opera performances. As regards the Combos 00 (concrete roof without vertical sound acoustic panels) and 01-a/b/c (wooden roof with draped curtains), the STI values are never lower than 0.42 and never higher than 0.70; therefore, the room never experiences poor or excellent conditions at any point. The Combos 01-a and 01-b, which have a non-performing C80, have a good STI index, confirming the difficulty of achieving a configuration that can be optimal a variety of uses. Combo 01 (wooden roof without vertical sound acoustic panels and no draped curtains), which has a good C80 value, presents a lower STI value, with an average performance. The STI values of Combo 02-a (characterized by wave false ceiling and vertical sound acoustic panels) are never lower than 0.52 and never higher than 0.60; therefore, neither poor nor excellent conditions are experienced in the room, but there is still a slight improvement over the combos 00 and 01. [ABSTRACT FROM AUTHOR]

Thermal modeling of building components plays a crucial role in designing energy efficiency measures, assessing living comfort, and preventing building damages. The accuracy of the modeling process strongly depends on the reliability of the physical models and the correct selection of input parameters, especially for historic buildings where uncertainties on wall composition and material properties are higher. This work evaluates the reliability of building thermal modeling and identifies the input parameters that most affect the simulation results. A monitoring system is applied to a historic building wall to measure the temperature profile. The long-term dataset is compared with the result of a simulation model. A sensitivity analysis is applied for the determination of the influential input parameters. A two-step optimization is performed to calibrate the numerical model: the first optimization step is based on an optimized selection of the database materials, while the second optimization step uses a particle swarm algorithm. The results indicate that the output of the simulation model is largely influenced by the coefficients describing the coupling with the boundary conditions and by the thermal conductivities of the materials. Very good results are obtained already after the first optimization step ( R M S E = 0.75   ° C) while the second optimization step improves further the agreement ( R M S E = 0.48   ° C) . The parameter values reported in the datasheets do not match those found through optimization. Even with extensive optimization using an algorithm, starting with monitoring data is insufficient to identify material parameter values. [ABSTRACT FROM AUTHOR]

Ensuring optimum interior lighting is a topic of great importance, as this influences not only the well-being of users but also the optimal performance of visual tasks. Lighting can be natural, but if not sufficient, it can be compensated with artificial lighting. This study highlights a methodology for designing a new lighting system that takes into account both technical and economic aspects. The method was applied to an existing school located in southern Italy, in which the electricity consumption is related to the current lighting system. The school is chosen as being representative of the construction type and layout of many local schools. In addition, the coexistence of several visual tasks with different design requisites (e.g., illuminance levels) makes the school a very complex environment. The school lighting is modelled in Google SketchUp and imported into Daysim to simulate the yearly and hourly daylight indoor contribution. Dialux Evo has been used to simulate and design artificial lighting. The results show a reduction of energy consumption of 33% with the simple replacement of fluorescent luminaires with LEDs, while the LED lamp dimming and modulation for rows of luminaires leads to a 95% reduction in energy consumption compared with the current state. [ABSTRACT FROM AUTHOR]

Finding the most appropriate configuration of building components at the design stage can reduce energy consumption in new buildings. This study aims to optimize the design of the envelope of a new residential building located in a warm climate (southern Italy). The thermal behaviour of the building has been analysed to evaluate the indoor operative air temperature for several configurations. The building prototype has been modelled using the dynamic simulation software TRNSYS 17 (A transient system simulation program, University of Wisconsin, Solar Energy Laboratory, USA, 2010) using a sequential search technique. Starting from the simplest building configuration, the main evaluated components are: walls, slab-on-ground floor, roof, shading, windows and internal heat loads. For each of these components, different design options have been modelled and compared in terms of indoor thermal comfort. Comfort parameters have also been taken into account to evaluate users' satisfaction with the optimized configurations. The study of the operative air temperature demonstrates that the absence of insulating layers in the ground floor ensures a lower internal temperature in summer. The paper shows how each component impacts the thermal behaviour of the whole building. It highlights the usefulness of the envelope design optimization that is characterized by high values of heat storage capacity, enabling internal temperature fluctuations to be kept under control, especially during summer. [ABSTRACT FROM AUTHOR]

Accounting for nearly 40% of final energy consumption, buildings are central to European energy policy. The Directive on Energy Performance of Buildings establishes a benchmarking system known as cost-optimality to set minimum energy performance requirements in new and existing buildings. This paper applies the cost-optimal methodology to an existing structure located in the Mediterranean area (Southern Italy). The building is composed of two units that have been considered for different uses: hotel and multi-residential. Several energy efficiency and renewable measures have been implemented both individually and as part of packages of measures. The cost-optimal solution has been identified as able to optimize energy consumption and costs from financial and macroeconomic perspectives. The first reference building (hotel use) shows a maximum reduction of primary energy and CO2 emission of about 42%, falling within the CasaClima energy class D, while the second reference building (residential use) achieves a value of 88% for primary energy and 85% for CO2 emissions, falling into class B. Thermal dispersions through the envelope can be limited using a suitable combination of insulating materials while a variety of technical variants are selected, such as VRF (variant refrigerant flow) systems, heat pumps with fan coils associated with controlled mechanical ventilation, solar thermal and photovoltaic. This paper illustrates the development of energy retrofit projects, in order to reach a balance between efficiency measures and costs for a building having two different uses, providing guidance to similar case studies related to a warm climate. [ABSTRACT FROM AUTHOR]

The recast of the energy performance of buildings directive (EPBD) describes a comparative methodological framework to promote energy efficiency and establish minimum energy performance requirements in buildings at the lowest costs. The aim of the cost-optimal methodology is to foster the achievement of nearly zero energy buildings (nZEBs), the new target for all new buildings by 2020, characterized by a high performance with a low energy requirement almost covered by renewable sources. The paper presents the results of the application of the cost-optimal methodology in two existing buildings located in the Mediterranean area. These buildings are a kindergarten and a nursery school that differ in construction period, materials and systems. Several combinations of measures have been applied to derive cost-effective efficient solutions for retrofitting. The cost-optimal level has been identified for each building and the best performing solutions have been selected considering both a financial and a macroeconomic analysis. The results illustrate the suitability of the methodology to assess cost-optimality and energy efficiency in school building refurbishment. The research shows the variants providing the most cost-effective balance between costs and energy saving. The cost-optimal solution reduces primary energy consumption by 85% and gas emissions by 82%-83% in each reference building. [ABSTRACT FROM AUTHOR]

This work presents a new protocol for monitoring rising damp, which is applied to three masonry models made of tuff, carparo, and Lecce stone. First, the physical characteristics of each stone were derived in the laboratory, which included porosity, imbibition, drying index, permeability, capillarity, and sorptivity. In this case, the protocol provided three columns, one for each material, consisting of five blocks. A layer of cotton tissue was interposed between columned blocks to simulate the hygroscopic behavior of a mortar, allowing a quick disassembly and reassembly of the multiblock columns for a quick weighing. The bottoms of the columns were immersed in water to a level of about three centimeters, providing a constant replenishment for the phenomena of evaporation and rising in the stone. The maximum height achieved by the rising damp depends on the characteristics of the building materials, i.e., the amount and size of pores, pore connectivity, etc. Since these materials have different physical characteristics, the objective was to quantify the rising moisture level of the three materials tested, block by block, in a controlled indoor microclimate environment. The three columns were periodically weighed, the quantity of collected water was evaluated, and a thermographic survey was performed. The results show that at the end of the test, the highest level of rising damp is reached by tuff with a height of 43 cm, followed by Lecce stone and carparo with a height of 40 cm and 21 cm, respectively. The innovation of this study is the proposal of a new flexible and easy-to-apply method for monitoring this phenomenon. It gives clear and numerically comparable results. Moreover, it is applicable to any type of stone, allowing the user to evaluate both the existing state and different design solutions. [ABSTRACT FROM AUTHOR]

This work proposes a new device for air treatment with dehumidification and water recovery/storage, with possible mitigation of indoor environmental conditions. The system is based on Peltier cells coupled with a horizontal earth-to-air heat exchanger, it is proposed as an easy-to-implement alternative to the heat pumps and air handling units currently used on the market, in terms of cost, ease of installation, and maintenance. The process provides the water collection from the cooling of warm-humid air through a process that leads to condensation and water vapor separation. The airflow generated by a fan splits into two dual flows that lap the two surfaces of the Peltier cells, one flow laps the cold surfaces undergoing sensible, latent cooling with dehumidification; the other flow laps the hot surfaces and heats up. The airflow undergoes thermal pre-treatment through the underground horizontal geothermal pipe that precedes the Peltier cells. In the water storage tank, which also works as a mixing chamber, the two air streams are mixed to regulate the outlet temperature. The system can be stand-alone if equipped with a photovoltaic panel and a micro wind turbine, able to be used in places where electricity is absent. The system, with different configurations, is modeled in the African city Kigali, in Rwanda. [ABSTRACT FROM AUTHOR]

This paper addresses the effects of long-term climate change on retrofit actions on a school building located in a Mediterranean climate. Dynamic energy simulations were performed using Termolog EpiX 11, first with conventional climate data and then with future year climate data exported from the CCWorldWeatherGen computational software. To date, many incentive actions are promoted for school renovations, but are these measures effective in preventing the discomfort that will be found due to overheating generated by climate change? Today, one of the main objectives in retrofit measures is the achievement of ZEB (Zero Energy Building) performance. Achieving this target requires first and foremost a high-performance envelope. This study evaluates the impact of retrofit strategies mostly applied to the school building envelope, over the years, considering three different time horizons, until 2080. Thermal performance indices and indoor operative temperature under free-floating were evaluated. The results highlight that, with a changing climate, it is no longer possible to assume a constant static condition to evaluate retrofit actions, but it is necessary to develop a predictive mathematical model that considers the design variability for future years. There is an urgent necessity to ensure both the safety and comfort of buildings while also anticipating future variations in climate. [ABSTRACT FROM AUTHOR]

This paper proposes a critical review of the different aspects concerning magnetic refrigeration systems, and performs a detailed analysis of thermodynamic cycles, using mathematical models found in the literature. Langevin's statistical mechanical theory faithfully describes the physical operation of a refrigeration machine working according to a magnetic Ericsson cycle. Results of mathematical and real experimental models are compared to deduce which best describes the Ericsson cycle. The theoretical data are not perfectly consistent with the experimental data; there is a maximum deviation of about 30%. Numerical and experimental data confirm that very high Coefficient of Performance (COP) values of more than 20 can be achieved. The analysis of the Brayton cycle consisted of finding the mathematical model that considers the irreversibility of these machines. Starting from the thermodynamic properties of magnetocaloric materials based on statistical mechanics, the efficiency of an irreversible Brayton regenerative magnetic refrigeration cycle is studied. Considering the irreversibility in adiabatic transformations, the lower limit of the optimal ratio of two magnetic fields is determined, obtaining a valid optimization criterion for these machines operating according to a Brayton cycle. The results show that the Ericsson cycle achieves a higher Coefficient of Performance than the Brayton cycle, which has a higher cooling capacity as it operates with a larger temperature difference between the magnetocaloric material and source. [ABSTRACT FROM AUTHOR]

Greenhouse crops represent a significant productive sector of the agricultural system; one of the main problems to be addressed is indoor air conditioning to ensure thermal well-being of crops. This study focuses on the ventilation analysis of solar greenhouse with symmetrical flat pitched roof and single span located in a warm temperate climate. This work proposes the dynamic analysis of the greenhouse modeled in TRNsys, simultaneously considering different thermal phenomena three-dimensional (3D) shortwave and longwave radiative exchange, airflow exchanges, presence of lamps with their exact 3D position, ground and plant evapotranspiration, and convective heat transfer coefficients. Several air conditioning systems were analyzed, automatic window opening, controlled mechanical ventilation systems (CMV) and horizontal Earth-to-Air Heat Exchanger (EAHX) coupled with CMV, for different air volume changes per hour. In summer, the exploitation of the ground allows having excellent results with the EAHX system, reducing the temperature peaks of up to 5 °C compared to the use of CMV. In winter, it is interesting to note that, although the EAHX is not the solution that raises the temperature the most during the day, its use allows flattening the thermal wave more. In fact, the trend is almost constant during the day, raising the temperature during the first and last hours of the day. [ABSTRACT FROM AUTHOR]

A light pipe is an excellent solution to transport and distribute daylight into environments without or with little lighting, guaranteeing comfort inside the rooms. As stated in the literature, the evaluation of the performances of light pipes presents numerous complexities, making the work very difficult for technicians and designers. This study is aimed to present a methodology that is able to identify the potential of light pipes using indices such as daylight autonomy (DA), continuous daylight autonomy (DAc), and useful daylight illuminance (UDI). This paper presents an analysis of daylight obtained by several configurations of simple models of light pipes installed into a 5 × 5 m plant area room. All simulations are carried out in a DAYSIM environment, which allows calculating the annual availability of daylight based on a RADIANCE raytracer backward. Several daylight conditions were analyzed for different light pipe configurations, considering different pipe lengths and a variable number of light pipes. The light pipes are tested also in the horizontal position, for different orientations. The results of all the combinations were compared with the performances of a window with dimensions equal to 1/8 of the internal surface, which was in accordance with the minimum value to be guaranteed by the Italian Regulation (D.M. 5 July 1975 n. 190) for different orientations. The results indicated a difference in daylight distribution, showing a strong correlation between the percentage levels of DA and DAc with the length and number of pipes, during different periods of the year. The simulated model is strongly influenced by the aspect ratio (R = diameter/length). The results show that the illuminance levels decrease drastically, increasing the length. [ABSTRACT FROM AUTHOR]

The building sector is responsible for a large part of the overall energy demand in Europe. Energy consumption may be reduced at the design stage by selecting the proper building elements. This study develops a multi-objective analysis for a highly efficient slab-on-ground floor, whose design is optimized for a warm climate. Possible floor configurations have been obtained using the software tools modeFRONTIER, for the multi-objective analysis, and MATLAB, for the computational code. To proceed with the optimization of the different floor layers, a dataset has been developed for several materials in relation to a number of parameters: thermo-physical properties, eco-sustainability score according to the ITACA Protocol, costs, source, and structural features. Results highlight how a high surface mass is preferable when guaranteed by concrete in the innermost and outermost layers. Furthermore, insulating materials are better placed in the middle layers, with the insulating and synthetic materials adjacent to the ground and insulating and natural materials adjacent to the floor. Results emphasize the importance of thermal transmittance close to the Italian regulation limit (0.38 W/m2 K) in the climatic zone C, to allow an adequate exchange with the ground in summer, avoiding overheating. The outcomes show that the obtained slab-on-ground floor configurations favor the use of local, recyclable, sustainable, and eco-friendly materials, which is in line with energy policies and sustainability protocols. The paper supports the decision making process that takes many variables into account at the building design stage. [ABSTRACT FROM AUTHOR]

A concept of Air-Cooled Heat Pump (ACHP) coupled with a Horizontal Air-Ground Heat Exchanger (HAGHE), also called Horizontal Earth-To-Air Heat Exchanger (EAHX), has been proposed. The Air-Cooled Heat Pump is a system which transfers heat from outside source (air) to inside sink (water) and vice versa in summertime. The innovation is to provide a geothermal treatment of pre-heating/cooling of air before meeting the evaporator in winter or the condenser in summer of the heat pump. Besides, it is known that the variations of the ground temperature, respect to the external air one, are mitigated already in the first layers of the ground throughout the year, due to the high thermal inertia of the ground, letting the heat pump work with more mitigated conditions, improving the performances. The behaviour of HAGHE has been investigated by varying the length and the installation depth of the probes, the air flow rate and the ground thermal properties. All the combinations have been implemented using TRNSYS 17 software (Transient System Simulation Program) to obtain the outlet temperatures from HAGHE, resulting from the 54 configurations. The results are compared in terms of Coefficient of Performance (COP) in wintertime and Energy Efficiency Ratio (EER) in summertime between configurations with and without the coupling with HAGHE. In addition, two seasonal performance SCOP and SEER coefficients have been calculated considering, not only the inlet air temperatures into the Air-Cooled Heat Pump, but also their frequency of occurrence, the off-set external temperature (16 °C), the nominal external temperature and heating and cooling loads. [ABSTRACT FROM AUTHOR]

Energy consumption in new buildings can be reduced at the design stage. This study optimizes the ventilation system design of a new residential building located in a warm climate (Southern Italy). Different system options of horizontal air-ground heat exchangers (HAGHEs), also called earth-to-air heat exchangers (EAHX), have been considered to search for the optimal configuration. The thermal behaviour of the obtained configurations has been modelled by the dynamic simulation software TRNSYS 17. The pipe numbers, the air flow rate, and the soil thermal conductivity are among the simulated building components. For each of them, different design options have been analysed to study how each parameter impacts the building thermal behaviour in winter and summer. The operative air temperature (TOP) has been evaluated inside the building prototype to investigate the indoor comfort. The paper demonstrates that HAGHEs permit to assure a suitable indoor climatization if the building envelope is optimized for a warm area. These conditions require high values of heat storage capacity to keep under control the internal temperature fluctuations, especially in summer. The paper confirms the importance of geothermal systems and design optimization to increase energy savings. [ABSTRACT FROM AUTHOR]