Search

Recent use of very small photon beams (down to 4 mm) in stereotactic radiotherapy requires new detectors to accurately determine the delivered dose. Diamond detectors have been presented in the literature as an attractive candidate for this application, due to their small detection volume and the diamond atomic number (Z=6) which is close to water effective atomic number (Zeff∼7.42). However, diamond exhibits a density 3.51 times greater than that of water and recent studies using Monte Carlo simulations have demonstrated the drawback of a high-density detector on small beam output factors. The current study focuses on geometrical parameters of diamond detector, namely, the diamond dimensions and the electrode geometry, in order to solve the dosimetric issues still observed in small photon beams with diamond detectors. To give better insights to these open questions, we have used both computational method and experimental analysis. This study highlighted that reducing diamond dimensions is crucial for small beam output factor measurements and to limit the influence of its high density. Furthermore, electrodes covering the whole diamond surface were essential for a dose rate independence of the diamond detector. The optimal dosimeter derived from this work presented small diamond dimensions of approximately 1-1-0.15mm3, with diamond-like-carbon electrodes covering the whole diamond surface. A dose rate independence of this diamond detector (better than 0.5% over a wide range of dose rates available on a stereotactic dedicated facility) was obtained due to the electrode geometry. Concerning the output factor measurements, a good agreement (better than 1.1%) was observed between this carbon material detector and two types of passive dosimeters (LiF microcubes and EBT2 radiochromic films) for all beam sizes except the smallest field of 0.6-0.6 cm2 with a deviation of 2.6%. This new study showed the high performance of this diamond detector in small photon beams, in comparison with various commercially available passive and active dosimeters. [ABSTRACT FROM AUTHOR]

The structural transformations induced in Gd2O3 and Eu2O3 irradiated with high-energy ions (94-MeV Pb and 1042-MeV Xe), where ionization processes (electronic stopping) dominate the ion slowing-down, have been studied via the combination of XRD and Raman experiments. Irradiation induces a cubic-to-monoclinic phase transformation; the radiation-induced monoclinic phase shows strong preferential orientation. This structural modification is accompanied by changes in the photoluminescence properties of sesquioxides. The results show that swift heavy ion irradiation is a powerful tool to control the properties of oxides at the nanoscale. [ABSTRACT FROM AUTHOR]

Purpose: To investigate the optimal use of XR-RV3 GafChromic® films to assess patient skin dose in interventional radiology while addressing the means to reduce uncertainties in dose assessment. Methods: XR-Type R GafChromic films have been shown to represent the most efficient and suitable solution to determine patient skin dose in interventional procedures. As film dosimetry can be associated with high uncertainty, this paper presents the EURADOS WG 12 initiative to carry out a comprehensive study of film characteristics with a multisite approach. The considered sources of uncertainties include scanner, film, and fitting-related errors. The work focused on studying film behavior with clinical high-dose-rate pulsed beams (previously unavailable in the literature) together with reference standard laboratory beams. Results: First, the performance analysis of six different scanner models has shown that scan uniformity perpendicular to the lamp motion axis and that long term stability are the main sources of scanner-related uncertainties. These could induce errors of up to 7% on the film readings unless regularly checked and corrected. Typically, scan uniformity correction matrices and reading normalization to the scanner-specific and daily background reading should be done. In addition, the analysis on multiple film batches has shown that XR-RV3 films have generally good uniformity within one batch (<1.5%), require 24 h to stabilize after the irradiation and their response is roughly independent of dose rate (<5%). However, XR-RV3 films showed large variations (up to 15%) with radiation quality both in standard laboratory and in clinical conditions. As such, and prior to conducting patient skin dose measurements, it is mandatory to choose the appropriate calibration beam quality depending on the characteristics of the x-ray systems that will be used clinically. In addition, yellow side film irradiations should be preferentially used since they showed a lower dependence on beam parameters compared to white side film irradiations. Finally, among the six different fit equations tested in this work, typically used third order polynomials and more rational and simplistic equations, of the form dose inversely proportional to pixel value, were both found to provide satisfactory results. Fitting-related uncertainty was clearly identified as a major contributor to the overall film dosimetry uncertainty with up to 40% error on the dose estimate. Conclusions: The overall uncertainty associated with the use of XR-RV3 films to determine skin dose in the interventional environment can realistically be estimated to be around 20% (k = 1). This uncertainty can be reduced to within 5% if carefully monitoring scanner, film, and fitting-related errors or it can easily increase to over 40% if minimal care is not taken. This work demonstrates the importance of appropriate calibration, reading, fitting, and other film-related and scan-related processes, which will help improve the accuracy of skin dose measurements in interventional procedures. [ABSTRACT FROM AUTHOR]

Purpose: In a previous work, output ratio (ORdet) measurements were performed for the 800 MU/min CyberKnife ® at the Oscar Lambret Center (COL, France) using several commercially available detectors as well as using two passive dosimeters (EBT2 radiochromic film and micro-LiF TLD-700). The primary aim of the present work was to determine by Monte Carlo calculations the output factor in water (OFMC,w) and the kQclin,Qmsrfclin,fmsr correction factors. The secondary aim was to study the detector response in small beams using Monte Carlo simulation. Methods: The LINAC head of the CyberKnife R ® was modeled using the PENELOPE Monte Carlo code system. The primary electron beam was modeled using a monoenergetic source with a radial gaussian distribution. The model was adjusted by comparisons between calculated and measured lateral profiles and tissue-phantom ratios obtained with the largest field. In addition, the PTW 60016 and 60017 diodes, PTW 60003 diamond, and micro-LiF were modeled. Output ratios with modeled detectors (ORMC,det) and OFMC,w were calculated and compared to measurements, in order to validate the model for smallest fields and to calculate kQclin,Qmsrfclin,fmsr correction factors, respectively. For the study of the influence of detector characteristics on their response in small beams; first, the impact of the atomic composition and the mass density of silicon, LiF, and diamond materials were investigated; second, the material, the volume averaging, and the coating effects of detecting material on the detector responses were estimated. Finally, the influence of the size of silicon chip on diode response was investigated. Results: Looking at measurement ratios (uncorrected output factors) compared to the OFMC,w, the PTW 60016, 60017 and Sun Nuclear EDGE diodes systematically over-responded (about +6% for the 5 mm field), whereas the PTW 31014 Pinpoint chamber systematically under-responded (about -12% for the 5 mm field). ORdet measured with the SFD diode and PTW 60003 diamond detectors were in good agreement with OFMC,w except for the 5 mm field size (about -7.5% for the diamond and +3% for the SFD). A good agreement with OFMC,w was obtained with the EBT2 film and micro- LiF dosimeters (deviation less than 1.4% for all fields investigated). kQclin,Qmsrfclin,fmsrcorrection factors for several detectors used in this work have been calculated. The impact of atomic composition on the dosimetric response of detectors was found to be insignificant, unlike the mass density and size of the detecting material. Conclusions: The results obtained with the passive dosimeters showed that they can be used for small beam OF measurements without correction factors. The study of detector response showed that ORdet is depending on the mass density, the volume averaging, and the coating effects of the detecting material. Each effect was quantified for the PTW 60016 and 60017 diodes, the micro- LiF, and the PTW 60003 diamond detectors. None of the active detectors used in this work can be recommended as a reference for small field dosimetry, but an improved diode detector with a smaller silicon chip coated with tissue-equivalent material is anticipated (by simulation) to be a reliable small field dosimetric detector in a nonequilibrium field. [ABSTRACT FROM AUTHOR]

Recent developments of new therapy techniques using small photon beams, such as stereotactic radiotherapy, require suitable detectors to determine the delivered dose with a high accuracy. The dosimeter has to be as close as possible to tissue equivalence and to exhibit a small detection volume compared to the size of the irradiation field, because of the lack of lateral electronic equilibrium in small beam. Characteristics of single crystal diamond (tissue equivalent material Z = 6, high density) make it an ideal candidate to fulfil most of small beam dosimetry requirements. A commercially available Element Six electronic grade synthetic diamond was used to develop a single crystal diamond dosimeter (SCDDo) with a small detection volume (0.165 mm3). Long term stability was studied by irradiating the SCDDo in a 60Co beam over 14 h. A good stability (deviation less than ± 0.1%) was observed. Repeatability, dose linearity, dose rate dependence and energy dependence were studied in a 10 × 10 cm2 beam produced by a Varian Clinac 2100 C linear accelerator. SCDDo lateral dose profile, depth dose curve and output factor (OF) measurements were performed for small photon beams with a micro multileaf collimator m3 (BrainLab) attached to the linac. This study is focused on the comparison of SCDDo measurements to those obtained with different commercially available active detectors: an unshielded silicon diode (PTW 60017), a shielded silicon diode (Sun Nuclear EDGE), a PinPoint ionization chamber (PTW 31014) and two natural diamond detectors (PTW 60003). SCDDo presents an excellent spatial resolution for dose profile measurements, due to its small detection volume. Low energy dependence (variation of 1.2% between 6 and 18 MV photon beam) and low dose rate dependence of the SCDDo (variation of 1% between 0.53 and 2.64 Gy min−1) are obtained, explaining the good agreement between the SCDDo and the efficient unshielded diode (PTW 60017) in depth dose curve measurements. For field sizes ranging from 0.6 × 0.6 to 10 × 10 cm2, OFs obtained with the SCDDo are between the OFs measured with the PinPoint ionization chamber and the Sun Nuclear EDGE diode that are known to respectively underestimate and overestimate OF values in small beam, due to the large detection volume of the chamber and the non-water equivalence of both detectors. [ABSTRACT FROM AUTHOR]

Many accidents in radiotherapy have been reported in France over the last years. This is due to the recent legal obligation to declare to the national safety authorities any significant incident relative to the use of ionising radiation including medical applications. The causes and consequences of the most serious events in radiotherapy are presented in this paper. Lessons can be learned from possible technical dysfunctions, from human errors or organisational weaknesses as to how such events can be prevented. The technical aspects are addressed here: in particular, dosimetric issues. [ABSTRACT FROM AUTHOR]

The therapeutic management of severe radiation burns remains a challenging issue. Conventional surgical treatment (excision and skin autograft or rotation flap) often fails to prevent unpredictable and uncontrolled extension of the radiation necrotic process. We report here an innovative therapeutic strategy applied to the victim of a radiation accident (December 15, 2005) with an iridium gammagraphy radioactive source (192Ir, 3.3 TBq). The approach combined numerical dosimetry-guided surgery with cellular therapy using mesenchymal stem cells. A very severe buttock radiation burn (2000 Gy at the center of the skin surface lesion) of a 27-year-old Chilean victim was widely excised (10 cm in diameter) using a physical and anatomical dose reconstruction in order to better define the limit of the surgical excision in apparently healthy tissues. A secondary extension of the radiation necrosis led to a new excision of fibronecrotic tissues associated with a local cellular therapy using autologous expanded mesenchymal stem cells as a source of trophic factors to promote tissue regeneration. Bone marrow-derived mesenchymal stem cells were expanded according to a clinical-grade technique using closed culture devices and serum-free medium enriched in human platelet lysate. The clinical evolution (radiation pain and healing progression) was favorable and no recurrence of radiation inflammatory waves was observed during the 11 month patient's follow-up. This novel multidisciplinary therapeutic approach combining physical techniques, surgical procedures and cellular therapy with adult stem cells may be of clinical relevance for improving the medical management of severe localized irradiations. It may open new prospects in the field of radiotherapy complications. [ABSTRACT FROM AUTHOR]

According to the United Nations Scientific Committee on the Effects of Atomic Radiation (UNSCEAR 1993), the dose due to the inhalation of radon decay products represents almost 50% of the total natural radiation dose to the general population. The scientific community is interested in the assessment of the risk induced by domestic radon exposure. The dosimetric models used to estimate the dose are very sensitive to unattached fraction and size distributions, which makes the characterization of the indoor radon decay products aerosol necessary. For this purpose, longterm measurements of unattached fraction (f[sub p]) and equilibrium factor (F) were taken in a dwelling under typical indoor domestic aerosol conditions. An original device consisting of an annular diffusion channel set in parallel with an open filter was developed and calibrated to continuously measure the unattached fraction. Moreover, radon activity concentration and particle concentration were simultaneously monitored. With aged aerosol, particle concentration was found to be very low (between 500 and 5000 cm[sup -3]), radon activity concentration ranged from 240 to 2800 Bq m[sup -3], and the mean values of f[sub p] and F were, respectively, 0.31 (0.08-0.67) and 0.16 (0.04-0.45). With aerosol sources, the high increase in particle concentration led to a negligible unattached fraction and raised the equilibrium factor. A correlation relationship was determined between these two parameters under different aerosol conditions. Finally,our experimental results were compared to results obtained with the PRADDO model; this comparison showed a good agreement between these two different approaches. [ABSTRACT FROM AUTHOR]

Starting in 1996, nonlinear approximation algorithms used for the determination of size distributions of ''unattached'' radon progeny from measurements made with diffusional size classification instruments were compared. Seven participants (one American and six European) took part using various techniques (Simplex, Expectation Maximization, Extreme Value Estimation, Twomey, and Random Walk) which are widely used for this type of work. Simulated input data was supplied to the participants. Their output data indicated that the quality of the results varied according to the algorithm used. This was particularly the case when retrieving parameters from bimodal distributions where large inaccuracies were shown. Variations were found between participants using basically identical algorithms. The influence of measurement uncertainties was investigated and indicated a serious reduction of retrieval accuracy, especially for algorithms with better than average performance for precise data. This work suggests that when high precision results are required, a random walk algorithm should be used and attention should be paid to reducing errors in the input penetration data. [ABSTRACT FROM AUTHOR]

Copyright of Materials & Structures is the property of Springer Nature and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

Copyright of Rheologica Acta is the property of Springer Nature and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

Survey of results recently obtained by the author about hereditary behaviour, Gibbs equation, caloric equation of state, local equilibrium, reversible accessibility, use of internal variables, behaviour classification. Toward a new and unified approach: thermodynamics in natural variables. [ABSTRACT FROM AUTHOR]

Rappel d'un algorithme numérique dû à Bazant, et permettant la résolution pas à pas des équations de Volterra de la visco-élasticité linéaire avec vieillissement. Application de cet algorithme au calcul pas à pas de l'évolution de la déformation moyenne et de la courbure dans une structure hétérogène du type multilame (stratifié ou fibré assimilable à des poutres hétérogènes chargées dans un plan de symétrie avec conservation des sections planes). Calcul pas à pas des déformations et contraintes dans chaque lame au niveau des interfaces. Calcul des flèches, en une section pour différentes portées ramené à celui d'une portée type et décomposé en deux cas d'importance pratique: courbure parabolique (charge transversale uniforme) et courbure constante (moment constant, charge axiale excentrée sans effets, du 2 ordre; variations dimensionnelles des matériaux constitutifs). Prise en compte de la précontrainte qui entre dans le formalisme génèral moyennant l'attribution à l'acier d'une prédéformation égale à l'opposé du quotient de la précontrainte initiale par le module d'élasticité instantané de l'acier. Indications pratiques sur le programme MULTIVIBAZ et exemple de résultats. The author restates a numerical algorithm defined by Bazant to solve Volterra equations of linear visco-elasticity with ageing. This algorithm is applied to step by step calculation of the development of mean, deformation and curvature in a heterogeneous structure of the multi-strip type (stratified or fibrous which can be likened to heterogeneous beams loaded in a symmetrical plane retaining plane crossections). Stresses and deformations are calculated step by step in each strip at the interfaces. The deflexions in a cross section for different spans are expressed in terms of a typical span divided into two cases of practical importance: parabolic curvature (uniform transverse load) and constant curvature (constant moment, eccentric axial load without second order effects; dimensional variations in materials used). The prestressing is taken into account in the general formalism through the attribution to the steel of a predeformation equal to the opposite of the quotient of the initial prestress to its instantaneous modulus of elasticity. The article concludes, with practical indications on the MULTIVIBIBAZ program and example of results. [ABSTRACT FROM AUTHOR]

Brush borders which are localized at the apical face of enterocytes, are composed of thousands of stiff microvilli containing bundles of microfilaments made of actin. Their assembly occurs during terminal differentiation of the enterocytes when these cells migrate along the villus of the intestinal mucosa. The cell line HT 29 derived from a human colonic adenocarcinoma whose differentiation can be induced, can also be used as a model to study in culture the assembly of the intestinal brush border. Villin is one of the actin binding proteins found in microvilli which compose brush borders. Villin is expressed in the adult and in the embryo before the appearance of the brush border. Villin can be used as a tissue-specific marker for normal diffentiated and undifferentiated cells derived from gastrointestinal tractus in the adult as well as in the embryo. Since villin is a good marker for intestinal cells and plays a structural role in the assembly of the brush border we have analysed its expression and its localization in HT 29 cells. In HT 29 cells, as in the tissue, villin is synthesized at low levels before the appearance of the brush border. The high rate of synthesis and the recruitement of villin at the apical pole of the cells can be correlated with the existence of a well developed brush border. [ABSTRACT FROM AUTHOR]

Copyright of Rheologica Acta is the property of Springer Nature and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

A severe irradiation accident involving a victim occurred in April 2009 in South America. The victim has found a 192Ir source fallen from a gammagraphy device and has put it in the left pocket of his pants. Very quickly, an erythema and a blister appeared on the left leg of the victim involving hospitalisation. Following the request of the IAEA assistance, the Ionizing Radiation Dosimetry Laboratory of IRSN was asked to perform a numerical dosimetric reconstruction. A personalised voxel phantom of the victim has been constructed thanks to the Simulation of External Source Accident with Medical images tool developed by the laboratory, and a calculation of the dose with the MCNPX computer code allowed to determine the boundary of the necrotic dose at 25 Gy. On the basis of these calculations, the physicians have performed exeresis of the necrotic region on the left leg on 4 May 2009. Associated with mesenchymal stem cell injection, the leg of the victim was healthy on December 2009. [ABSTRACT FROM PUBLISHER]

Purpose: The use of small photon fields is now an established practice in stereotactic radiosurgery and radiotherapy. However, due to a lack of lateral electron equilibrium and high dose gradients, it is difficult to accurately measure the dosimetric quantities required for the commissioning of such systems. Moreover, there is still no metrological dosimetric reference for this kind of beam today. In this context, the first objective of this work was to determine and to compare small fields output factors (OF) measured with different types of active detectors and passive dosimeters for three types of facilities: a CyberKnife® system, a dedicated medical linear accelerator (Novalis) equipped with m3 microMLC and circular cones, and an adaptive medical linear accelerator (Clinac 2100) equipped with an additional m3 microMLC. The second one was to determine the kQclin,Qmsrfclin,fmsr correction factors introduced in a recently proposed small field dosimetry formalism for different active detectors. Methods: Small field sizes were defined either by microMLC down to 6 × 6 mm2 or by circular cones down to 4 mm in diameter. OF measurements were performed with several commercially available active detectors dedicated to measurements in small fields (high resolution diodes: IBA SFD, Sun Nuclear EDGE, PTW 60016, PTW 60017; ionizing chambers: PTW 31014 PinPoint chamber, PTW 31018 microLion liquid chamber, and PTW 60003 natural diamond). Two types of passive dosimeters were used: LiF microcubes and EBT2 radiochromic films. Results: Significant differences between the results obtained by several dosimetric systems were observed, particularly for the smallest field size for which the difference in the measured OF reaches more than 20%. For passive dosimeters, an excellent agreement was observed (better than 2%) between EBT2 and LiF microcubes for all OF measurements. Moreover, it has been shown that these passive dosimeters do not require correction factors and can then be used as reference dosimeters. Correction factors for the active detectors have then been determined from the mean experimental OF measured by the passive dosimeters. Conclusions: Four sets of correction factors needed to apply the new small field dosimetry formalism are provided for several active detectors. A protocol for small photon beams OF determination based on passive dosimeters measurements has been recently proposed to French radiotherapy treatment centers. [ABSTRACT FROM AUTHOR]