Search

Aim: To examine the occurrence of repeated differential activation between the heads of the biceps brachii muscle and its relation to fatigue prevention during a submaximal contraction. Methods: Thirty-nine subjects carried out an isometric contraction of elbow flexion at 25% of maximal voluntary contraction (MVC) until exhaustion. A grid of 13 by 10 electrodes was used to record surface electromyographic signals from both heads of the biceps brachii. The root-mean-square of signals recorded from electrodes located medially and laterally was used to analyse activation differences. Differential activation was defined as periods of 33% different activation level between the two heads of the biceps brachii muscle. Results: Differential muscle activation was demonstrated in 30 of 33 subjects with appropriate data quality. The frequency of differential activation increased from 4.9 to 6.6 min−1 at the end of the contractions with no change in duration of the differential activations (about 1.4 s). Moreover, the frequency of differential activation was, in general, negatively correlated with time to exhaustion. Conclusion: The observed differential activation between the heads of the biceps brachii can be explained by an uneven distribution of synaptic input to the motor neurone pool. The findings of this study indicate that differential activation of regions within a muscle does not prevent fatigue at a contraction level of 25% of MVC. [ABSTRACT FROM AUTHOR]

When multichannel surface-electromyography (MCSEMG) systems are used, there is a risk of recording low-quality signals. Such signals can be confusing for analysis and interpretation and can be caused by power-line interference, motion artifacts or poor electrode-skin contact. Usually, the electrode-skin impedance is measured to estimate the quality of the contact between the electrodes and the skin. However, this is not always practical, and the contact can change over short time-scales. A fast method is described to estimate the quality of individual signals of monopolar MCSEMG recordings based on volume conduction of myo-electric signals. The characteristics of the signals were described using two descriptor variables. Outliers (extreme data points) were detected in the two-dimensional distributions of the descriptor variables using a non-parametric technique, and the quality of the signals was estimated by their outlier probabilities. The method's performance was evaluated using 1 s long signals visually classified as very poor (G 1), poor (G2) or good quality (G3). Recordings from different subjects, contraction levels and muscles were used. An optimum threshold at 0.05 outlier probability was proposed and resulted in classification accuracies of 100% and > 70% for G I and G2 signals, respectively, whereas <5% of the G3 signals were classified as poor. In conclusion, the proposed method estimated MCSEMG signal quality with high accuracy, compared with visual assessment, and is suitable for on-line implementation. The method could be applied to other multichannel sensor systems, with an arbitrary number of descriptor variables, when their distributions can be assumed to lie within a certain range. [ABSTRACT FROM AUTHOR]

The paper presents a new approach for simultaneous estimation of muscle fibre conduction velocity (MFCV) and muscle fibre orientation (MFO) for motor units (MUs) in two-dimensional (2D) multichannel surface electromyography recordings. This is an important tool for detecting changes and abnormalities in muscle function and structure. In addition, simultaneous estimation of MFO and MFCV avoids the necessity of manual electrode alignment. The proposed method detected propagating MU action potentials (MUAPs) in a running time window as moving components in amplitude maps. Thereafter, estimations were obtained by fitting a three-dimensional function to these maps. The performance was evaluated using synthetic MU signals at 10 dB SNR and authentic biceps brachii measurements. Results demonstrated MFCV and MFO estimates with standard deviations of less than 0.05 m s(-1) and 1 degrees for simulated signals, and less than 0.2 m s(-1) and 4 degrees for experimental data. However, standard deviations as low as 0.12 m s(-1) and 1.6 degrees from real signals were demonstrated. It was concluded that the method performs as well as, or better than, linear array multichannel methods when individual propagating MUAPs can be identified, even if electrodes are not aligned with fibre direction. [ABSTRACT FROM AUTHOR]

Spatial filtering of surface electromyography (EMG) signals can be used to enhance single motor unit action potentials (MUAPs). Traditional spatial filters for surface EMG do not take into consideration that some electrodes could have poor skin contact. In contrast to the traditional a priori defined filters, this study introduces an adaptive spatial filtering method that adapts to the signal characteristics. The adaptive filter, the maximum kurtosis filter (MKF), was obtained by using the linear combination of surrounding channels that maximises kurtosis. The MKF and conventional filters were applied to simulated EMG signals and to real EMG signals recorded with an electrode grid to evaluate their performance in detecting single motor units. The MKF was compared with conventional spatial filtering methods. Simulated signals, with different levels of spatially correlated noise, were used for comparison. The influence of one electrode with poor skin contact was also investigated. The MKF was found to be considerably better at enhancing a single MUAP than conventional methods for all levels of spatial correlation of the noise. For a spatial correlation of 0.97 of the noise, the improvement in the signal-to-noise ratio, where a MUAP could be detected, was at least 6dB. With a simulated poor skin contact for one electrode, the improvement over the other methods was at least 19 dB. [ABSTRACT FROM AUTHOR]

Spatial filtering of surface electromyography (EMG) signals can be used to enhance single motor unit action potentials (MUAPs). Traditional spatial filters for surface EMG do not take Into consideration that some electrodes could have poor skin contact to contrast to the traditional a priori defined filters, this study introduces an adaptive spatial filtering method that adapts to the signal characteristics. The adaptive filter, the maximum kurtosis filter (MKF), was obtained by using the linear combination of surrounding channels that maximises kurtosis. The MKF and conventional filters were applied to simulated EMG signals and to real EMG signals recorded with an electrode grid to evaluate their performance in detecting single motor units. The MKF was compared with conventional spatial filtering methods. Simulated signals, with different levels of spatially correlated noise, were used for comparison. The influence of one electrode with poor skin contact was also investigated. The MKF was found to be considerably better at enhancing a single MUAP than conventional methods for alt levels of spatial correlation of the noise. For a spatial correlation of 0.97 of the noise, the improvement in the signal-to-noise ratio, where a MUAP could be detected, was at least 6dB. With a simulated poor skin contact for one electrode, the improvement over the other methods was at least 19 dB. [ABSTRACT FROM AUTHOR]