Search

With the background of the fossil fuel energy crisis, the development of self-healing and recyclable polymer materials has become a research hotspot. In this work, a kind of cross-linking agent with pendent furan groups was first prepared and then used to produce the Polyurethane elastomer based on Diels–Alder chemistry (EPU–DA). In addition, in order to further enhance the mechanical properties of the elastomer, cellulose nanofibers (CNFs) were added into the Polyurethane system to prepare a series of composites with various contents of CNF (wt% = 0.1~0.7). Herein, the FTIR and DSC were used to confirm structure and thermal reversible character. The tensile test also indicated that the addition of CNF increased the mechanical properties compared to the pure Polyurethane elastomer. Due to their reversible DA covalent bonds, the elastomer and composites were recycled under high-temperature conditions, which extends Polyurethane elastomers' practical applications. Moreover, damaged coating can also be repaired, endowing this Polyurethane material with good potential for application in the field of metal protection. [ABSTRACT FROM AUTHOR]

Magnetron-sputtered WS2 composite thin films are solid lubricants with excellent performances. However, the low hardness of the WS2 thin films necessitates the further improvement of their wear resistance. For this purpose, an effective strategy is to alternately deposit or code posit WS2 and a hard phase, such as TiB2, to form hard lubricant thin films. Herein, a TiB2 thin film was prepared under the same conditions as those used for depositing the WS2 thin film with a dense structure and excellent tribological properties. Because of the high deposition energy of high-power impulse magnetron sputtering (HiPIMS), the TiB2 thin film possesses a dense structure and leather-like flat surface (hardness = 24.17 GPa). The friction coefficient of the film under different loads ranges between 0.6 and 0.8. The wear rate of the thin film increases with load, mainly because of fatigue wear and abrasive wear. Under high loads, obvious furrow-like wear marks are observed. At different sliding frequencies, except 8 Hz, the friction coefficient of the film ranges from 0.6 to 0.8. The main wear mode is fatigue wear, particularly at increasing sliding frequencies. Although the film possesses a relatively high friction coefficient, its wear resistance is excellent (minimum wear rate = 1.96 × 10−6 mm3/(N·m)). [ABSTRACT FROM AUTHOR]

In this work, the Polyurethane/MoS2 composites (PUM) filled with different amount of modified molybdenum disulfide (MoS2) were prepared by solution-blending-casting method. The thermal reversible Diels–Alder (DA) bonds enabled the polymer system recyclable ability. The modified MoS2 were obtained by tannic acid (TA) assistant ultra-sonication exfoliation method were used to improve the gas barrier performance of materials. Compared with the pure PU, about twofold decrease in oxygen gas permeability of PUM composites (from 6719 to 3927 cm3/m2˙d˙Pa) were obtained with 1 wt% MoS2. More important, the samples showed excellent gas barrier and mechanical properties before and after being hygrothermal aged for 100 h. The PUM composites had good gas barrier and recyclability and had great potential application prospects in packing materials. [ABSTRACT FROM AUTHOR]

ZTEM refers to the Z-axis tipper electromagnetic method. The ZTEM method is an airborne magnetotelluric sounding method based on the difference in rocks' resistivity using the native electromagnetic field. The method is effective in exploring large-scale structures when the ground is fluctuant. The paper introduces the inversion algorithm of 2D ZTEM named the conjugate gradient method. This method, which avoids solving the Jacobi matrix, is very effective but not effective enough when the model is divided into a big grid. This study can perform further computation using parallel computation and then receive the processed data. We compare the results of the serial algorithm with the result of the parallel algorithm, which proves that the parallel algorithm is correct. When the number of processes is between three and six, the speedup ratio is between 1.74 and 3.19. It improves the effectiveness of the parallel algorithm of 2D ZTEM. [ABSTRACT FROM AUTHOR]

Population aging requires innovative solutions to increase the quality of life and preserve autonomous and independent living at home. A need of particular significance is the identification of behavioral drifts. A relevant behavioral drift concerns sociality: older people tend to isolate themselves. There is therefore the need to find methodologies to identify if, when, and how long the person is in the company of other people (possibly, also considering the number). The challenge is to address this task in poorly sensorized apartments, with non-intrusive sensors that are typically wireless and can only provide local and simple information. The proposed method addresses technological issues, such as PIR (Passive InfraRed) blind times, topological issues, such as sensor interference due to the inability to separate detection areas, and algorithmic issues. The house is modeled as a graph to constrain transitions between adjacent rooms. Each room is associated with a set of values, for each identified person. These values decay over time and represent the probability that each person is still in the room. Because the used sensors cannot determine the number of people, the approach is based on a multi-branch inference that, over time, differentiates the movements in the apartment and estimates the number of people. The proposed algorithm has been validated with real data obtaining an accuracy of 86.8%. [ABSTRACT FROM AUTHOR]

In the present work, different aging treatments were performed to investigate the pre-aging effect on the formation of Ω phase and mechanical properties in Al-Cu-Mg-Ag alloy. The results showed that pre-strain could inhibit the formation of Ω phases, which was detrimental to the alloy strength. Due to the introduction of pre-aging treatment before pre-strain, the adverse effect of pre-strain on the precipitation of the Ω phase was reduced, and the alloy strength was increased by at least 15 MPa. Besides this, increasing the pre-aging temperature promoted the precipitation of Ω phases, inhibited the formation of θ′ phases, and improved the alloy strength. This was because the higher pre-aging temperature promoted more pre-precipitated Ω phases in the pre-aging process, and most of the pre-precipitated Ω phases could be retained and grew in the subsequent aging process. As a result, the tensile strength of the alloy increased from 523 MPa to 540 MPa. In addition, pre-aging with a higher temperature consumed more solute atoms, leading to less residual solute atoms in the matrix. Thus, the adverse effects of pre-strain, which inhibit the formation of clusters by the segregation of solute atoms, were reduced. [ABSTRACT FROM AUTHOR]

The development of polymer-based composites with self-healing and recyclable capability has attracted the attention of several researchers for resource recycling and environment protection. In this work, Halloysite nanotubes (HNTs) reinforced polyurethane materials (PU) with self-healing and recyclable ability were constructed by in situ polymerization method. The mechanical, thermal amd morphological properties of PU and related composites were studied. The morphology of samples fracture surface ensured the homogeneous dispersion of HNTs in the polymer matrix. Moreover, thermal stability was improved with the incorporation of the HNTs. The tensile test showed strength increased with HNTs content increased. The tensile strength of composites increases from 23.38 to 34.92 MPa at 2 wt% HNTs. Therefore, the designed strategy provides a simple approach for preparing high mechanical properties, reprocessing and self-healing ability polyurethane composites. [ABSTRACT FROM AUTHOR]

Although ovarian cancer is common, its prognosis remains poor because of drug resistance and early metastasis. Polysaccharides extracted from Bangia fuscopurpurea (BFP) are potential anti‐cancer agents, but the mechanisms underlying their effects in human ovarian cancer remain unclear. Here, we investigated the mechanisms of action of BFP polysaccharides in A2780 ovarian cancer cells using cell migration, invasion, apoptosis, and autophagy assays. Transwell assays indicated that BFP inhibited cell migration and invasion. Flow cytometry analysis showed that BFP treatment induced apoptosis and reactive oxygen species production, while significantly reducing mitochondrial membrane potential. Reverse transcription–polymerase chain reaction and Western blot analyses revealed changes in the expression of apoptosis‐ and autophagy‐related cellular mRNAs and proteins, respectively, following BFP treatment for 24 h. Transmission electron microscopy revealed that BFP induced autophagy in A2780 cells. These findings demonstrate that BFP may be useful for developing functional foods for cancer therapy. [ABSTRACT FROM AUTHOR]

Due to the outstanding properties comprised of thermal, anti-corrosion and excellent processing properties, the polyurethane coating has received attention from many researchers. However, absence of self-healing capacity limited their applications. In the present work, a self-healing polyurethane (PU) was developed for protective coating via Diels–Alder reaction. Moreover, incorporation of Halloysite nanotubes (HNTs) by in situ polymerization method in the PU enhances the mechanical properties. The macro- and micro-mechanical properties of materials were investigated by tensile and nanoindentation measurement, these results show the composites displayed higher tensile strength (34.2 MPa) and hardness (5.13 MPa) in comparison with pure PU (22.9 MPa and 4.24 MPa). The tensile and POM results indicated that the PU and composites have excellent self-healing property. The simulative salt spray tests indicated the coating possessed an excellent corrosion protection property. Therefore, this work is promising for the self-healing ability protective polymer coating. [ABSTRACT FROM AUTHOR]

Electrical anisotropy is increasingly recognized as an important aspect of the resistivity models required to explain magnetotelluric (MT) observations. However, a limited number of practical MT inversion algorithms that can consider anisotropy have been published to date. To address this problem, we have developed a three‐dimensional (3‐D) MT inversion algorithm that recovers a 3‐D resistivity model that considers arbitrary electrical anisotropy. The inversion uses the same inversion algorithm as the widely used ModEM inversion algorithm, and a novel forward modeling algorithm to consider the anisotropic Earth. The algorithm was tested on both synthetic and field MT data. Inversions considered both a completely general anisotropy tensor with six components and approximations with less parameters. Synthetic inversions show that the two horizontal components of resistivity and the anisotropy strike can be well recovered, while the vertical component of resistivity is poorly resolved, primarily because current flow in MTs is dominantly horizontal. The synthetic examples confirm the limitation of the axial anisotropic inversion technique when applied to MT data produced by a resistivity model with arbitrary anisotropy. The synthetic inversions also showed that inversion of data from an isotropic model will not result in an artificially anisotropic model. Compared to the isotropic inversion model of the real MT data, the anisotropic model clearly shows some features that are consistent with the mapped geology. As expected, the results showed that a given data set can be fit by a range of models, with an inherent trade‐off from 3‐D heterogeneity to 3‐D anisotropy. This uncertainty can be reduced with the use of prior information in the inversion. Plain Language Summary: The resistivity model of real Earth generally contains anisotropic features. Field magnetotelluric (MT) data may be significantly influenced by these features. To interpret such data, inversion algorithms which can consider electrical anisotropy are highly demanded. However, a limited number of practical MT inversion algorithms that can consider anisotropy have been published to date. To address this problem, we have developed a three‐dimensional (3‐D) MT inversion algorithm that recovers a 3‐D resistivity model that considers arbitrary electrical anisotropy. The algorithm was tested to be effective on both synthetic and field MT data. Compared to the isotropic inversion models of the tested MT data, the resolved anisotropic models are more reliable. Key Points: A three‐dimensional non‐linear conjugate gradient inversion algorithm is implemented for the inversion of magnetotelluric (MT) data to produce an electrical resistivity model with arbitrary anisotropyInversion examples of synthetic and real MT data validate the usefulness of the algorithmReal MT data inversion obtains an anisotropic model which is more consistent with the mapped geology than the corresponding isotropic model [ABSTRACT FROM AUTHOR]

MoS2–TiL/MoS2–TiH coating (L and H are low and high power of the sputtered Ti target) possesses excellent tribological properties owing to its nano-multilayer structure. In this study, the tribological properties of MoS2–TiL/MoS2–TiH coating were extensively analyzed at different loads. Relative to the MoS2–Ti monolayer coating, the nano-multilayer structure not only improved the wear resistance but also increased the critical load at which the coating began to peel off. The MoS2–Ti coating maintained its lubrication only in the early stage of the test even at a load of 2 N. In contrast, the friction coefficient and wear rate of the multilayer coating were small and stable until the load reached 20 N. The critical load of the optimized MoS2–TiL/MoS2–TiH coating was 10 times that of the MoS2–Ti coating. At excessive loads, the multilayer coating lost its lubrication in the early stage of the test because the coating was completely worn off under such loading. [ABSTRACT FROM AUTHOR]

A dual crosslinked self‐healing polyurethane was prepared with robust mechanical properties through the dynamic reversible pyridine‐Fe3+ coordination bonds and Diels–Alder (DA) covalent bonds dual crosslinking strategy. Moreover, the mechanical properties and self‐healing ability of polyurethane can be tuned readily by different ratio of the coordination bonds and DA bonds. Under external load, the coordination bonds serve as sacrificial bonds are broken to dissipate energy, the DA bonds can keep the shape of sample. With the coordination bonds participation, the damaged samples can be healed under moderate heating treatment or with the aid of FeCl3 solution. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2019, 57, 2228–2234 [ABSTRACT FROM AUTHOR]

3D controlled-source audio frequency magnetotelluric (CSAMT) responses can be distorted strongly by topography and should be accounted for in data inversion and interpretation. In this paper we present a scheme to incorporate topographic distortions into the inversion instead of correcting them. This approach has been verified by comparing the modelling results with 2D FEM CSAMT solutions and synthetic inversion examples. Compared with the responses generated from a half-space model with flat surface, it is found that not only the topography in the survey area but also that at the source position may strongly distort the CSAMT responses. The field example indicates that results with topography are much better than those without considering topography to map the distribution of coal seam underground, which also illustrates the effectiveness of our approach. [ABSTRACT FROM AUTHOR]

The controlled-source audio-frequency magnetotelluric (CSAMT) method has become an important method in geophysical electromagnetic exploration. However, traditional CSAMT only gathers a single set of orthogonal electric and magnetic data, which cannot describe the whole subsurface geological structure. Due to increasingly complex geological targets, the drawbacks of traditional CSAMT have gradually become more significant, promoting the need for tensor CSAMT. Tensor CSAMT can gather richer information, but the 3D forward and inversion models of this method have developed slowly since it was first proposed. The common method for inverting the data of the tensor CSAMT is still magnetotelluric (MT). This paper adopts a staggered-grid finite difference method to realise the 3D forward modelling of the tensor CSAMT. On this basis, we adopt a limited-memory Broyden-Fletcher-Goldfarb-Shanno (LBFGS) method to implement a 3D inversion with full impedance data. Through inverting synthetic and real data, we prove that: (1) directly using an MT method to invert the data of the tensor CSAMT will obtain an incorrect result, (2) the inversion result of tensor CSAMT is more reliable than that of the traditional CSAMT, and (3) LBFGS is more efficient than the nonlinear conjugate gradient (NLCG) for tensor CSAMT.Our research shows that 3D tensorCSAMTinversion with LBFGS is very useful and practical for electromagnetic exploration. [ABSTRACT FROM AUTHOR]

The eastern terminations of the Himalayan orogeny, named Namche Barwa, are considered a vital natural laboratory in the Tibetan plateau for geodynamics due to its distinctive geological and geomorphological characteristics. Magnetotelluric (MT) data measured at 83 sites around the Namche Barwa are imaged by three-dimensional (3-D) inversion to better reveal the crustal structure of the eastern Himalaya. The results show a complex and heterogeneous electrical structure beneath the Namche Barwa. The electrical conductors distributed in the middle and lower crust around the Namche Barwa provide additional evidence for the 'crustal flow' model if they are considered as some parts of the flow in a relatively large-scale region. The near-surface resistivity model beneath the inner part of Namche Barwa conforms with the locations of hot spring and fluid inclusions, the brittle-ductile transition, and the 300°C-400°C isotherm from previous hydrothermal studies. Relatively resistive upper crust (>800 Ωm) is underlain by a more conductive middle to lower crust (<80 Ωm). The electrical characteristics of the thermal structure at shallow depth indicate an accumulation of hydrous melting, a localized conductive steep dipping zone for decompression melting consistent with the 'tectonic aneurysm' model for explaining the exhumation mechanism of metamorphic rocks at Namche Barwa. The results also imply that both surface processes and local tectonic responses play a vital role in the evolution of Namche Barwa. An alternative hypothesis that the primary sustained heat source accounts for the local thermal-rheological structure beneath Namche Barwa is also discussed. [ABSTRACT FROM AUTHOR]

Obtaining detailed information regarding the interfacial characteristics of metal/hexagonal-TMN composites is imperative for developing these materials with optimal mechanical properties. To this end, we systematically investigate the work of adhesion, fracture toughness, and interfacial stability of M/Cr2N and M/V2N interfaces using first-principles calculations. The orientation (0001) of hexagonal phases and (111) of fcc phases are selected as the interface orientations. Accordingly, we construct M/Cr2N interface models by considering 1N, 2N, and Cr terminations of Cr2N(0001), as well as two stacking sequences (top and hollow sites) for the 1N- and 2N-terminated interface models, respectively. The M/V2N interface models are constructed in the same way. The V-terminated Ni/V2N interface is demonstrated to provide a good combination of the work of adhesion, fracture toughness, and interfacial stability. Therefore, the Ni/V2N interface model can be regarded as the preferred configuration among the metal/hexagonal-TMN interface models considered. The present results offer a practical perspective for tailoring the interfaces in metal/hexagonal-TMN composite materials to obtain improved mechanical properties. [ABSTRACT FROM AUTHOR]

We developed a three-dimensional (3D) conjugate gradient inversion algorithm for inverting magnetotelluric impedance tensor measurements. In order to show the importance of including diagonal components of magnetotelluric impedance tensor in 3D inversion, synthetic data were inverted using the 3D conjugate gradient inversion, and the inversion results were compared and analyzed. The results from the 3D inversion of synthetic data indicate that both the off-diagonal and the diagonal components are required in inversions to obtain better inversion results when there are no enough data sites to recover the target resistivity structure. These examples show that lots of information about 3D structure is also contained in the diagonal components; as a result, diagonal components should be included in 3D inversions. The inversion algorithm was also used to invert the impedance tensor data acquired in the Kayabe area in Japan. Inversions with the synthetic and real data demonstrated the validity and practicability of the inversion algorithm. [ABSTRACT FROM AUTHOR]

We implement a parallel algorithm with the advantage of MPI (Message Passing Interface) to speed up the rapid relaxation inversion for 3D magnetotelluric data. We test the parallel rapid relaxation algorithm with synthetic and real data. The execution efficiency of the algorithm for several different situations is also compared. The results indicate that the parallel rapid relaxation algorithm for 3D magnetotelluric inversion is effective. This parallel algorithm implemented on a common PC promotes the practical application of 3D magnetotelluric inversion and can be suitable for the other geophysical 3D modeling and inversion. [ABSTRACT FROM AUTHOR]

Based on the analysis of the conjugate gradient algorithm, we implement a threedimensional (3D) conjugate gradient inversion algorithm with magnetotelluric impedance data. During the inversion process, the 3D conjugate gradient inversion algorithm doesn’ t need to compute and store the Jacobian matrix but directly updates the model from the computation of the Jacobian matrix. Requiring only one forward and four pseudo-forward modeling applications per frequency to produce the model update at each iteration, this algorithm efficiently reduces the computation of the inversion. From a trial inversion with synthetic magnetotelluric data, the validity and stability of the 3D conjugate gradient inversion algorithm is verified. [ABSTRACT FROM AUTHOR]

MoS2–Ti coating is a widely used solid lubricant owing to its low friction coefficient. The mechanical and tribological performance of the coating can be further improved via introducing a multilayer structure, which is closely related to the modulation period and significantly affects the properties of the coating. Herein, the effect of two different modulation periods on the mechanical and tribological performance of the MoS2–TiL/MoS2–TiH multilayer coatings (where L and H represent low and high-powered sputtering of the titanium target) was studied. The performance of the coatings was found to depend on modulation periods of single layer thickness and thickness ratio, respectively. When the thickness ratio of MoS2–TiL layer to MoS2–TiH layer was fixed with different number of layers, the adverse effects of the interface outweighed the beneficial effect; thus, the mechanical and tribological performance of the multilayer coatings were improved with an increase in the single layer thickness. When the effect of the multilayer interfaces on the studied coatings was similar with the same number of layers, the MoS2–TiH layer had more impact on the hardness of the MoS2–TiL/MoS2–TiH multilayer coatings, whereas the MoS2–TiL layer substantially affected the adhesion properties, friction behavior and wear resistance. This study can provide a way to regulate coatings with different performance requirements via building different multilayer microstructures. [ABSTRACT FROM AUTHOR]

Thermosetting polymers, such as epoxy resins, have found widespread applications because of their excellent thermomechanical and solvent resistance properties. However, the recycling of thermosets remains a challenge, due to the irreversible covalent crosslinking bonds in the network. The exchangeable covalent bonds in vitrimers open opportunities in the way that materials can be dynamically repaired. However, in the case of polyolefins, the strategy of exchangeable vitrimers is still underexplored. Herein, a simple way is reported to prepare a high‐density polyethylene (HDPE) vitrimer with a triple shape memory effect, where exchangeable esters are introduced into the network of covalently crosslinked HDPE. With the incorporation of polyethers or polyesters into the crosslinked network, the two obtained vitrimers show outstanding recyclability and a good triple shape memory effect. This new strategy of preparing an HDPE vitrimer might allow the high‐value utilization of crosslinked polyolefins. A simple way is reported to prepare a high‐density polyethylene (HDPE) vitrimer with triple shape memory effect, where exchangeable esters are introduced into the network of covalently crosslinked HDPE. With the incorporation of polyethers and polyesters into the crosslinked network, both the obtained vitrimers show outstanding recyclability and a good triple shape memory effect. [ABSTRACT FROM AUTHOR]