Search

ZnO nanorods are coated with a conformal film of CdTe nanoparticles using a layer-by-layer (LbL) process. By increasing the number of CdTe layers the absorption of incident light increases at wavelengths lower than the absorption onset of the nanoparticles (650 nm). At the absorption peak of the nanoparticles, 50 layers of nanoparticles coated onto ZnO nanorods absorb 80% of the incident light. Annealing of the ZnO–CdTe composites leads to a small red-shift in this absorption onset, but does not destroy the quantum confinement of the nanoparticles. Solar cells are produced by filling the CdTe-coated nanorods with CuSCN or PEDOT:PSS, and tested under AM 1.5 illumination. Annealing of the LbL films is essential to reduce the series resistance of the cell. Annealed cells generate an open-circuit voltage of 120 mV and a short-circuit current density of 0.19 mA cm−2. [ABSTRACT FROM AUTHOR]

Abstract  The production of lead zirconate titanate (PZT) with a variation in Zr and Ti ratios using a hydrothermal method has been attempted. We show that when reactions are conducted at 160 °C, for 4 h, the phase of PZT produced is independent of the initial Zr/Ti precursor ratio. In all cases we produce PZT with a crystal structure close to the morphotropic phase boundary, i.e. Zr/Ti ≈ 52:48. The excess precursors either fail to react, or form amorphous and crystalline impurity phases that are detectable via powder XRD after the hydrothermal treatment. Using an excess of Pb precursor is shown to aid the crystallisation of the resultant PZT powder, as verified by SEM and FIB analysis. [ABSTRACT FROM AUTHOR]

Recently there has been great interest in using patterned ferroelectric materials for the photochemical growth of metal nanostructures. Variations in surface and sub-surface structure influence the photochemical processes. Here we show that crystallography, and hence remnant polarization, of the ferroelectric affects photo-deposition. The ratio of metal growth on c− and c+ domains varies from 1 : 2 for [100] to 1 : 100 for [111]. This is shown to be dependent on the variations in the band structure. [ABSTRACT FROM AUTHOR]

ZnO nanorods are doped with Sb during the aqueous chemical synthesis by addition of Sb acetate dissolved in ethylene glycol. [ABSTRACT FROM AUTHOR]

Using BaTiO3 as a model ferroelectric material we investigated the influence of the ferroelectric dipole on the photocatalytic activity of a heterogeneous BaTiO3/α-Fe2O3 photocatalyst. Two distinct BaTiO3 samples were used: BTO and BTO-A. The latter consists more ferroelectric tetragonal phase and thus stronger ferroelectricity. It was found that under identical experimental conditions, the photodecolourisation rate of a target dye using BTO-A/α-Fe2O3 under visible light was 1.3 times that of BTO/α-Fe2O3. Photoelectrochemical and photoluminescence analysis confirmed a more effective charge carrier separation in BTO-A/α-Fe2O3. Considering solely the photoexcitation of α-Fe2O3 in the composite photocatalysts under visible light and the similar microstructures of the two catalysts, we propose that the enhanced decolourisation rate when using BTO-A/α-Fe2O3 is due to the improved charge carrier separation and extended charge carrier lifetime arising from an interaction between the ferroelectric dipole and the carriers in α-Fe2O3. Our results demonstrate a new process to use a ferroelectric dipole to manipulate the charge carrier transport, overcome recombination, and extend the charge carrier lifetime of the surface material in a heterogeneous catalyst system. [ABSTRACT FROM AUTHOR]

A blue-green fluorescent organic dye and red-emitting nanoparticles, based on II-VI semiconductors, have been used together in the fabrication of white organic light-emitting devices. In this work, the materials were combined in two different ways: in the form of a blend, and as separate layers deposited on the opposite sides of the substrate. The blended-layer structure provided purer white emission. However, this device also exhibited a number of disadvantages, namely a high drive voltage, a low efficiency and some colour instability. These problems could be avoided by using a device structure that was fabricated using separate dye and nanoparticle layers. [ABSTRACT FROM AUTHOR]

Naturally selected T-cell receptors (TCRs) are characterised by low binding affinities, typically in the range 1–100 µM. Crystal structures of syngeneic TCRs bound to peptide major histocompatibility complex (pMHC) antigens exhibit a conserved mode of binding characterised by a distinct diagonal binding geometry, with poor shape complementarity (SC) between receptor and ligand. Here, we report the structures of three in vitro affinity enhanced TCRs that recognise the pMHC tumour epitope NY-ESO157–165 (SLLMWITQC). These crystal structures reveal that the docking mode for the high affinity TCRs is identical to that reported for the parental wild-type TCR, with only subtle changes in the mutated complementarity determining regions (CDRs) that form contacts with pMHC; both CDR2 and CDR3 mutations act synergistically to improve the overall affinity. Comparison of free and bound TCR structures for both wild-type and a CDR3 mutant reveal an induced fit mechanism arising from restructuring of CDR3 loops which allows better peptide binding. Overall, an increased interface area, improved SC and additional H-bonding interactions are observed, accounting for the increase in affinity. Most notably, there is a marked increase in the SC for the central methionine and tryptophan peptide motif over the native TCR. [ABSTRACT FROM AUTHOR]