Search

Systematic research into device-induced red blood cell (RBC) damage beyond hemolysis, including correlations between hemolysis and RBC-derived extracellular vesicles, remains limited. This study investigated non-physiological shear stress-induced RBC damage and changes in related biochemical indicators under two blood pump clinical support conditions. Pressure heads of 100 and 350 mmHg, numerical simulation methods, and two in vitro loops were utilized to analyze the shear stress and changes in RBC morphology, hemolysis, biochemistry, metabolism, and oxidative stress. The blood pump created higher shear stress in the 350-mmHg condition than in the 100-mmHg condition. With prolonged blood pump operation, plasma-free hemoglobin and cholesterol increased, whereas plasma glucose and nitric oxide decreased in both loops. Notably, plasma iron and triglyceride concentrations increased only in the 350-mmHg condition. The RBC count and morphology, plasma lactic dehydrogenase, and oxidative stress across loops did not differ significantly. Plasma extracellular vesicles, including RBC-derived microparticles, increased significantly at 600 min in both loops. Hemolysis correlated with plasma triglyceride, cholesterol, glucose, and nitric oxide levels. Shear stress, but not oxidative stress, was the main cause of RBC damage. Hemolysis alone inadequately reflects overall blood pump-induced RBC damage, suggesting the need for additional biomarkers for comprehensive assessments. [ABSTRACT FROM AUTHOR]

To investigate the effects of clinical modalities and configurations on oxygenator pressure loss (ΔP), oxygen transfer ability and thrombosis risk and to find out the optimal oxygenator configuration. Modified partial pressure of oxygen (PO2) and a newly proposed thrombosis risk model (constructed from platelets, coagulation factors, hemostatic proteins, and blood stagnation) were used for this study. Oxygen transport and thrombosis risk assessment experiments were used for validation. Both simulation and experimental results indicate that when oxygenator operates at low flow rates with low-pressure loss and high PO2, they produced thrombin concentrations and increased thrombosis risk. For the same membrane fiber region, variations in the oxygenator external structure did not affect PO2 and thrombin production. For the ΔP and thrombosis risk, square oxygenators > round oxygenators, single-inlet oxygenators > multiple-inlet oxygenators, and lower inlet and lower outlet oxygenators > center inlet and center outlet oxygenators. The oxygenator high thrombosis risk region was identified as the blood-to-blood/border impingement region. A study of 81 oxygenator inlet and outlet combinations found that the inlet and outlet locations had little effect on ΔP and PO2. Oxygenator thrombosis risk was the lowest when using a center inlet and an upper/lower outlet configuration. The accuracy of the thrombosis risk model was validated. The oxygenator operation mode had a significant effect on ΔP, PO2, and thrombosis risk. Changes in the oxygenator external configuration had a significant impact on thrombosis. The lowest thrombosis risk was found in the center inlet and upper/lower outlet round oxygenator configuration. [ABSTRACT FROM AUTHOR]

An abdominal aortic aneurysm (AAA) is a typical aortic disease with serious complications. In clinical practice, the decision to intervene in treatment depends on the rupture risk of AAA. Therefore, monitoring the progression of the disease and accurately assessing the rupture risk is of great importance for its treatment. Studies have shown that the biomechanical indicators based on multi-scale models are more effective in accurately assessing the rupture risk of AAA. However, using computational fluid dynamics (CFD) to simulate the biomechanical environment is a cumbersome and time-consuming process, which is inadequate to meet the needs of clinical monitoring and quick decisions. While the hemodynamic environment of AAA is heavily dependent on geometry, more and more biomechanics-related morphological parameters have been raised and validated. In this review, we summarized typical morphological parameters associated with AAA rupture and their relationships with the mechanical environment, including maximum diameter, deformation rate, saccular index, asymmetry, AAA volume, tortuosity, and intraluminal thrombus (ILT), providing a reference for clinical preoperative risk assessment. Clinical Impact: Studies have shown that the biomechanical indicators based on multi-scale models are more effective in accurately assessing the rupture risk of AAA. To meet the need for clinical monitoring and rapid decision making, the typical morphological parameters associated with AAA rupture and their relationships with the mechanical environment have been summarized, which provide a reference for clinical preoperative risk assessment of AAA. [ABSTRACT FROM AUTHOR]

Women with abdominal aortic aneurysm (AAA) have a higher incidence of complications after Endovascular aneurysm repair (EVAR), most of which are related to the migration of stent‐graft. The different force acting on the stent‐graft after EVAR caused by different abdominal artery anatomy of male and female AAA patients may be the reason for the sex‐different complications. This article aims to explore the possible biomechanical mechanisms of sex differences by making a comparison of displacement force acting on the stent graft of male and female AAA patients. To explore the effect of different vascular anatomy on stent‐graft migration, the uniformed models were constructed according to the specific vascular anatomy parameters of AAA patients of different sex, which have been measured before. The computational fluid dynamics method was used to quantitate the pulsatile force acting on the stent‐graft after EVAR in a cardiac cycle. Then the displacement force was calculated with the pressure and the wall shear stress, and the total and area‐weighted average of displacement force acting on the stent‐graft were compared respectively. In one cardiac cycle, the wall pressure for the male model is greater than that of the female model (2.7–4.4 vs. 2.2–3.4 N), and the wall shear force for the female model is slightly greater (0–0.0065 vs. 0–0.0055 N). The displacement force is mainly provided by the wall pressure, which is also greater in the male model. However, the area‐averaged displacement force is greater for the female model than that for the male model (180–290 vs. 160–250 Pa). Because of the different vascular anatomies, the impact caused by the pulsating aortic blood flow on the AAA stent‐graft of women after EVAR was greater than that of men. Women's vascular anatomy leads to greater area‐averaged displacement force after stent‐graft implantation, resulting in a greater risk of stent‐graft migration, which might be one of the reasons why women had a higher incidence of complications after EVAR. [ABSTRACT FROM AUTHOR]

To investigate the effect of rotor design configuration on hemodynamic features, hemocompatibility and dynamic balance of blood pumps. Computational fluid dynamics was employed to investigate the effects of rotor type (closed impeller, semi‐open impeller), clearance height and back vanes on blood pump performance. In particular, the Eulerian hemolysis model based on a power‐law function and the Lagrangian thrombus model with integrated stress accumulation and residence time were applied to evaluate the hemocompatibility of the blood pump. This study shows that compared to the closed impeller, the semi‐open impeller can improve hemolysis at a slight sacrifice in head pressure, but increase the risk of thrombogenic potential and disrupt rotor dynamic balance. For the semi‐open impeller, the pressure head, hemolysis, and axial thrust of the blood pump decrease with increasing front clearance, and the risk of thrombosis increases first and then decreases with increasing front clearance. Variations in back clearance have little effect on pressure head, but larger on back clearance, worsens hemolysis, thrombogenic potential and rotor dynamic balance. The employment of back vanes has little effect on the pressure head. All back vanes configurations have an increased risk of hemolysis in the blood pump but are beneficial for the improvement of the rotor dynamic balance of the blood pump. Reasonable back vanes configuration (higher height, wider width, longer length and more number) decreases the flow separation, increases the velocity of blood in the back clearance, and reduces the risk of blood pooling and thrombosis. It was also found that hemolysis index (HI) was highly negatively correlated with pressure difference between the top and back clearances (r = −.87), and thrombogenic potential was positively correlated with pressure difference between the top and back clearances (r =.71). This study found that rotor type, clearance height, and back vanes significantly affect the hydraulic performance, hemocompatibility and rotor dynamic balance of centrifugal blood pumps through secondary flow. These parameters should be carefully selected when designing and optimizing centrifugal blood pumps for improving the blood pump clinical outcomes. [ABSTRACT FROM AUTHOR]

Background: The centrifugal blood pump volute has a significant impact on its hemodynamic performance hemocompatibility. Previous studies about the effect of volute design features on the performance of blood pumps are relatively few. Methods: In the present study, the computational fluid dynamics (CFD) method was utilized to evaluate the impact of volute design factors, including spiral start position, volute tongue radius, inlet height, size, shape and diffuser pipe angle on the hemolysis index and thrombogenic potential of the centrifugal blood pump. Results: Correlation analysis shows that flow losses affect the hemocompatibility of the blood pump by influencing shear stress and residence time. The closer the spiral start position of the volute, the better the hydraulic performance and hemocompatibility of the blood pump. Too large or too small volute inlet heights can worsen hydraulic performance and hemolysis, and higher volute inlet height can increase the thrombogenic potential. Small volute sizes exacerbate hemolysis and large volute sizes increase the thrombogenic risk, but volute size does not affect hydraulic performance. When the diffuser pipe is tangent to the base circle of the volute, the best hydraulic performance and hemolysis performance of the blood pump is achieved, but the thrombogenic potential is increased. The trapezoid volute has poor hydraulic performance and hemocompatibility. The round volute has the best hydraulic and hemolysis performance, but the thrombogenic potential is higher than that of the rectangle volute. Conclusion: This study found that the hemolysis index shows a significant correlation with spiral start position, volute size, and diffuser pipe angle. Thrombogenic potential exhibits a good correlation with all the studied volute design features. The flow losses affect the hemocompatibility of the blood pump by influencing shear stress and residence time. The finding of this study can be used to guide the optimization of blood pump for improving the hemodynamic performance and hemocompatibility. [ABSTRACT FROM AUTHOR]

Purpose: The purpose of this study was to investigate the impact of a new arterial intravascular pump on the hemodynamic surroundings within the aorta. Methods: A new arterial intravascular pump was placed in the descending aorta, and the effects of three positions within the aorta, as well as the number (n = 1 to 3) of pumps, on arterial flow features, organ perfusion, and blood trauma were investigated using a computational fluid dynamics (CFD) method. Results: It was found that as the pump position was moved backward, the perfusion in the three bifurcated vessels of the aorta arch increased and the pump suction flow decreased, resulting in a reduced high shear stress and decreased residence time in the three branches of the aortic arch. The further posterior the location of the pump, the better the blood flow perfusion to the kidneys, while the perfusion at the bifurcation of the abdominal aorta was reduced, due to the pump suction effect. Compared to the condition with single pump support, the multi-pump assist model can significantly reduce the pump rotating speed, while keeping the same flow patterns, leading to a decreased volume of high shear stress and flow loss. When increasing the number of pumps, the perfusion to the three branches of the aortic arch increased, accompanied by a diminished residence time, and the perfusion to the other aortic branches was decreased. However, the perfusion to the other aortic branches, especially for the renal arteries and even under a three-pump condition, was close to that without pump assistance. Conclusion: The placement of an intravascular pump near the beginning of the suprarenal abdominal aorta was considered the optimal location, in order to improve the hemodynamic surroundings. Increasing the number of pumps can significantly reduce the rotational speed, while maintaining the same flowrate, with a decreased fluid energy loss and a reduced high shear stress. This arterial intravascular pump can effectively improve renal blood flow. [ABSTRACT FROM AUTHOR]

(1) Background: Thrombosis is the main complication in patients supported with ventricular assist devices (VAD). Models that accurately predict the risk of thrombus formation in VADs are still lacking. When VADs are clinically assisted, their complex geometric configuration and high rotating speed inevitably generate complex flow fields and high shear stress. These non-physiological factors can damage blood cells and proteins, release coagulant factors and trigger thrombosis. In this study, a more accurate model for thrombus assessment was constructed by integrating parameters such as shear stress, residence time and coagulant factors, so as to accurately assess the probability of thrombosis in three clinical VADs. (2) Methods: A mathematical model was constructed to assess platelet activation and thrombosis within VADs. By solving the transport equation, the influence of various factors such as shear stress, residence time and coagulation factors on platelet activation was considered. The diffusion equation was applied to determine the role of activated platelets and substance deposition on thrombus formation. The momentum equation was introduced to describe the obstruction to blood flow when thrombus is formed, and finally a more comprehensive and accurate model for thrombus assessment in patients with VAD was obtained. Numerical simulations of three clinically VADs (CH-VAD, HVAD and HMII) were performed using this model. The simulation results were compared with experimental data on platelet activation caused by the three VADs. The simulated thrombogenic potential in different regions of MHII was compared with the frequency of thrombosis occurring in the regions in clinic. The regions of high thrombotic risk for HVAD and HMII observed in experiments were compared with the regions predicted by simulation. (3) Results: It was found that the percentage of activated platelets within the VAD obtained by solving the thrombosis model developed in this study was in high agreement with the experimental data (r² = 0.984), the likelihood of thrombosis in the regions of the simulation showed excellent correlation with the clinical statistics (r² = 0.994), and the regions of high thrombotic risk predicted by the simulation were consistent with the experimental results. Further study revealed that the three clinical VADs (CH-VAD, HVAD and HMII) were prone to thrombus formation in the inner side of the secondary flow passage, the clearance between cone and impeller, and the corner region of the inlet pipe, respectively. The risk of platelet activation and thrombus formation for the three VADs was low to high for CH-VAD, HVAD, and HM II, respectively. (4) Conclusions: In this study, a more comprehensive and accurate thrombosis model was constructed by combining parameters such as shear stress, residence time, and coagulation factors. Simulation results of thrombotic risk received with this model showed excellent correlation with experimental and clinical data. It is important for determining the degree of platelet activation in VAD and identifying regions prone to thrombus formation, as well as guiding the optimal design of VAD and clinical treatment. [ABSTRACT FROM AUTHOR]

The degradation time is a crucial factor in evaluating the performance of poly (lactic-co-glycolic acid) (PLGA) stents. Bulk degradation mode was commonly used to analyze the stent degradation behavior by finite element approach. However, the PLGA stents may present surface degradation more than bulk degradation under certain conditions, which will greatly affect the degradation time after implantation. In this study, the degradation processes of the poly (lactic-co-glycolic acid) stent were reproduced utilizing finite element analysis. Both bulk degradation and surface degradation modes were considered. The correlation between tensile stress and degradation rate was investigated. The degradation time was analyzed selectively. The stress distribution, fracture, and mass loss were also compared between bulk degradation mode and surface degradation mode. The simulation results showed that, in both evolution modes, the degradation began at the 'peak-valley' region and fracture occurred at the cross of links and rings. Additionally, high levels of Von-Mises stress were observed in these two regions. Compared with bulk degradation, the fracture time of the stent was delayed by 63% in the surface degradation mode. In conclusion, the mass loss rate and scaffolding period showed great differences between surface degradation and bulk degradation. Based on this study, it is suggested that bulk degradation mode is not applicable to the case of inadequate water uptake mode, such as the tracheal stent degradation process. More experimental research should be carried out to accurately predict the scaffolding period after implantation. The mechanical properties of the fracture zone should be strengthened. [ABSTRACT FROM AUTHOR]

In accordance with "the response to injury" theory, the entry of monocytes into the intima guided by inflammation signals, taking up cholesterol and transforming into foam cells, and egress from plaques determines the progression of atherosclerosis. Multiple cytokines and receptors have been reported to be involved in monocyte recruitment such as CCL2/CCR2, CCL5/CCR5, and CX3CL1/CX3CR1, and the egress of macrophages from the plaque like CCR7/CCL19/CCL21. Interestingly, some neural guidance molecules such as Netrin-1 and Semaphorin 3E have been demonstrated to show an inhibitory effect on monocyte migration. During the processes of monocytes recruitment and migration, factors affecting the biomechanical properties (e.g., the membrane fluidity, the deformability, and stiffness) of the monocytes, like cholesterol, amyloid-β peptide (Aβ), and lipopolysaccharides (LPS), as well as the biomechanical environment that the monocytes are exposed, like the extracellular matrix stiffness, mechanical stretch, blood flow, and hypertension, were discussed in the latter section. Till now, several small interfering RNAs (siRNAs), monoclonal antibodies, and antagonists for CCR2 have been designed and shown promising efficiency on atherosclerosis therapy. Seeking more possible biochemical factors that are chemotactic or can affect the biomechanical properties of monocytes, and uncovering the underlying mechanism, will be helpful in future studies. [ABSTRACT FROM AUTHOR]

Endothelial cells (ECs) in vivo are subjected to three forms of shear stress induced by luminal blood flow, transendothelial flow and interstitial flow simultaneously. It is controversial that shear stress, especially the component induced by luminal flow, was thought to inhibit the initialization of angiogenesis and trigger arteriogenesis. Here, we combined microfabrication techniques and delicate numerical simulations to reconstruct the initial physiological microenvironment of neovascularization in vitro, where ECs experience high luminal shear stress, physiological transendothelial flow and various vascular endothelial growth factor (VEGF) distributions simultaneously. With the biomimetic microfluidic model, cell alignment and endothelial sprouting assays were carried out. We found that luminal shear stress inhibits endothelial sprouting and tubule formation in a dose-dependent manner. Although a high concentration of VEGF increases EC sprouting, neither a positive nor a negative VEGF gradient additionally affects the degree of sprouting, and luminal shear stress significantly attenuates neovascularization even in the presence of VEGF. Heparinase was used to selectively degrade the heparan sulfate proteoglycan (HSPG) coating on ECs and messenger RNA profiles in ECs were analyzed. It turned out that HSPGs could act as a mechanosensor to sense the change of fluid shear stress, modulate multiple EC gene expressions, and hence affect neovascularization. In summary, distraction from the stabilized state, such as decreased luminal shear stress, increased VEGF and the destructed mechanotransduction of HSPGs would induce the initiation of neovascularization. Our study highlights the key role of the magnitude and forms of shear stress in neovascularization. [ABSTRACT FROM AUTHOR]

Background: Gender difference in cardiovascular diseases (CVDs) is an important topic in the field of cardiovascular medicine. In this study, we focused on the mortality difference of abdominal aortic aneurysms (AAA), which is higher for female than that of male. The aim of this study was to verify whether morphological and hemodynamic factors play their roles in this phenomenon. Methods: Patient-specific AAA models of 11 females and 23 males with similar age and body mass index (BMI) have been reconstructed based on clinical computed tomography (CT) data. Firstly, the morphological parameters (diameters, curvature, intraluminal thrombus volume, etc.) of AAA models and lumbar vertebrae models were collected and analyzed. Then, based on statistical results of morphological parameters, uniformed male and female AAA models were reconstructed, and hemodynamic simulations were conducted respectively. In post-processing, the hemodynamic performances induced by gender-different morphological geometries were analyzed and compared. Results: The comparison of morphological parameters revealed that the average curvature of lumbar vertebrae and AAA centerline of female AAA models were obviously higher than that of the male. The amount of intraluminal thrombus in female AAA models was relatively lower than that of the male. According to the hemodynamic simulation, the uniform female AAA model has higher peak pressure, lower oscillatory shear stress index (OSI), and lower relative residence time (RRT) than that of the male model, all of which put female AAA to a relatively higher risk hemodynamic situation. Conclusions: The morphological and hemodynamic features of AAA have very obvious gender differences that would induce higher risk of rupture for female AAA biomechanically. These findings would help to explore the mechanism of gender differences in AAA and draw attention to gender-specific consideration for AAA treatment. More morphological and hemodynamic indictors are suggested to be involved in the future guidelines. [ABSTRACT FROM AUTHOR]

Objectives. The study investigates local hemodynamic environment changes caused by straightening phenomenon and the relationship between straightening phenomenon and in-stent restenosis. Background. Intravascular intervention is an effective treatment in restoring the normal flow conditions and vascular lumen. Unfortunately, in-stent restenosis often occurs in a subset of patients after stent implantation and limits the success of stent implantation outcomes. The implanted stent usually causes artery straightening locally, rather than coinciding and adjusting to the physiological curve exactly. Artery straightening would apparently modify the artery geometry and therefore alter the local hemodynamic environment, which may result in intimal hyperplasia and restenosis after stenting implantation. Methods. In the current investigation, we verify the hypothesis that the artery straightening influences the local hemodynamic state using the different 3D CT models. Flow analysis for blood in the left anterior descending coronary artery and the straightening model is simulated numerically. Result. The current results reveal that the straightening phenomenon alters the distribution of wall shear stress and flow patterns, decreases the wall shear stress (WSS), and increases the oscillatory shear index (OSI) and the relative residence time (RRT), especially at the proximal and distal areas of stenting. Conclusions. The local straightened geometry established after stent implantation was likely to generate portions of the stenting area to a high risk of neointimal hyperplasia and subsequent restenosis. [ABSTRACT FROM AUTHOR]

Among the interventional stenting methods for treating coronary bifurcation lesions, the conventional treatments still have disadvantages, which include increased intervention difficulties or inadequate supply of blood flow to side branches and may alter the physiological function of downstream organs. Thus, the optimized design of stent geometry needs to be improved based on the specific shape of branches to minimize the complications of inadequate blood flow to the downstream organs and tissues. Our research used 3D modeling and fluid dynamics simulation to design and evaluate a new stent with locally enlarged segment by altering the proportion and length of enlarged surface area based on Bernoulli's equation. The aim is to increase the pressure and blood flow supply at side branches. According to series of blood flow simulations, the stent with 10% enlargement of surface area and length of 3 folders of stent diameter was assigned as the optimized design. The results revealed that by using this design, according to the simulation results, the average pressure on side branches increased at the rate of 43.6%, which would contribute to the adequate blood supply to the downstream organs. Besides, the average wall shear stress (WSS) at sidewalls increased at 9.2% while the average WSS on the host artery wall decreased at 14.1%. There is in the absent of noticeable rise in the total area of low WSS that blows the threshold of 0.5 Pa. Therefore, the present study provides a new method to optimize the hemodynamics features of stent for bifurcation arteries. [ABSTRACT FROM AUTHOR]

The importance of vascular cell glycocalyx in mechanotransduction has been demonstrated by many studies. The simulated microgravity induced a region‐dependent adaptation of arterial glycocalyx including its thickness, coverage, and gene expression in conduit arteries of tail‐suspended rats has been reported in our previous studies. Herein, we extended this line of research by quantifying the mRNA levels of three nitric oxide synthase (NOSI, NOSII, and NOSIII) and evaluating the apoptotic rates of endothelial cells (ECs) and smooth muscle cells (SMCs) in the common carotid artery, abdominal aorta, and femoral artery of 3 week tail‐suspended rats. Results indicated that the tail suspension of rats induced about 0.36, 0.22, and 0.33 fold down‐regulation of NOSI, NOSII, and NOSIII in the abdominal aorta, while 3.21, and 3.48 fold up‐regulation of NOSII and NOSIII in the carotid artery and no significant effects on three NOS isoforms in the femoral artery. Moreover, the apoptosis of ECs and SMCs were significantly inhibited in both carotid artery and abdominal aorta, while enhanced in the femoral artery of the tail‐suspended rats. A linear positive correlation exists between the normalized coverage of the glycocalyx and the normalized NOSI and NOSIII mRNA levels. These results indicated that the redistribution of haemodynamics in the conduit arteries of 3 week tail‐suspended rats regulated the glycocalyx, NOS expression, and vascular cell apoptosis in a region‐dependent manner, contributing to the final vascular remodelling under simulated microgravity condition. [ABSTRACT FROM AUTHOR]

Objective: This study evaluates the overall survival and the infection-relapse after endovascular repair (Endo) vs. open surgery (Open) for mycotic aortic aneurysms and the potential influence of perioperative severity of infection to the decision-making on the long-term survival. Design: A multicenter, retrospective analysis of 5247 consecutive aortic aneurysm repair performed from January 2003 to December 2017 at five tertiary medical centers was conducted. Among the study population, 257 patients with mycotic aortic aneurysms s were identified. Methods: Finally, 73 patients were enrolled in the cohort after exclusion and a 1:1 propensity-matched analysis. The study cohort drawn from matched data included 37 patients in the Endo group and 36 patients in the Open group. The primary endpoint was overall survival. Secondary endpoints included infection-relapse during the follow-up. Univariate and multivariate Cox regression analyses were used to assess predictors for late mortality. Results: The mean follow-up time for the entire cohort was 41 months (range, 1 to 135 months). Among propensity-matched patients, there was no significant difference in baseline characteristics. There was no difference in overall survival (P = 0.083) between the groups at five years, but Open group was associated with a lower infection-relapse incidence during the follow-up (P = 0.011). Subgroup analysis revealed a better survival rate for Open in patients with severe infection (P = 0.003) or small periaortic abscess (P = 0.049). Conclusion: There were no significant differences between Endo and Open in overall survival. However, Open was a more definite option with less infection-relapse and had potential advantages for patients with severe infection or with a small periaortic abscess. [ABSTRACT FROM AUTHOR]

Objectives: Postoperative pancreatic fistula (POPF) is a major concern after pancreatoduodenectomy (PD). We recently designed a new anastomotic method to reduce the rate of pancreatic fistula: polytetrafluoroethylene suture buttress-reinforced pancreaticojejunostomy (PBRP).Methods: An animal model and a computer simulation were used to measure the maximum stress and tensile strength of the pancreas with and without the suture buttresses. Then, a randomized controlled trial (RCT) was performed to compare the outcome of PD between patients who underwent PBRP vs traditional pancreaticojejunostomy (TP).Results: The maximum load in the animal model was significantly higher with the suture buttresses than without (5.47 ± 1.67 N vs 3.72 ± 1.36 N, p < 0.01), and in the computer simulation, the peak stress was lower with the suture buttresses than without (54.86 vs 486.8 MPa). There were no significant differences between the two groups in the overall frequency of POPF, but the rate of clinically relevant POPF was significantly lower in the PBRP group (2.8 vs 22.8%, p = 0.028). The pancreaticojejunostomy time was significantly longer in the PBRP group (19.57 ± 3.31 vs 17.17 ± 4.83 min, p = 0.018), and the PBRP group showed a shorter drainage tube retention duration (10 vs 12 days, p = 0.006) and postoperative hospital stay (13 d vs 15 d, p = 0.031).Conclusions: PBRP is a feasible and reliable procedure for preventing clinically relevant POPF. Additional multi-institution randomized trials should be conducted to confirm these results. [ABSTRACT FROM AUTHOR]

To investigate the hemodynamic effects of partial obstruction to the renal orifice caused by inappropriate stent-graft location. Pre-operative and deployment models of a stent graft with various degrees of obstruction to the renal orifice are constructed based on medical images of abdominal aortic aneurysm. Hemodynamics, including flow pattern, time-averaged wall shear stress (TAWSS), oscillatory shear index (OSI), as well as relative residence time (RRT) are analyzed using numerical simulations. Flow rate distributions are assessed and verified by in vitro experiments. Results show that partial blockage to the renal branch orifice leads to flow recirculation and vortices with low wall shear stress around the renal ostia, whereas OSI and RRT on the renal arteries increase with the degree of obstruction. While the in vitro experiment indicates a decreasing flow rate to the bilateral renal arteries as renal artery ostia are obstructed. In conclusion, obstruction to the renal arteries induced by an inappropriate stent graft location causes stenosis in the renal artery in the long term. This study reveals a possible pathological mechanism of renal complications due to the implantation of a stent graft. [ABSTRACT FROM AUTHOR]

Local flow disturbance by arterial stent struts has been shown to play an important role in stent thrombosis. To reduce the local flow disturbance near a stent strut, we proposed a new concept of stent design with small holes in the stent struts. The present study evaluated the new design numerically by comparing it with the traditional stent in terms of local hemodynamic parameters such as flow velocity, flow recirculation area, time-averaged wall shear stress (TAWSS), oscillating shear index (OSI), and relative residence time (RRT). The results demonstrated that when compared with the traditional strut, the new design could significantly enhance flow velocity and reduce the flow recirculation zone in the vicinity of the strut. Moreover, the new design would significantly elevate TAWSS and remarkably reduce OSI and RRT along the host arterial wall. In conclusion, the new design of stent struts with punched holes is advantageous over the traditional one in the aspect of improving local hemodynamics, which may reduce thrombosis formation and promote re-endothelialization after stenting. [ABSTRACT FROM AUTHOR]

Local hemodynamic environment is a determinant factor in drug delivery from a drug eluting stent (DES) to the target arterial tissue. By using a simplified model of a DES, we demonstrated that if a DES had a drug release mode of uniform rate the drug released from the stent will distribute non-uniformly along the stent due to the flowing blood, with a significantly higher drug concentration at the distal part of the stent than that at the proximal one. This may explain why a DES could retard neointimal formation and vascular remodeling in downstream coronary segments. To solve this problem, we thereafter optimized the drug release mode of the DES as an exponential function. The simulation results showed that the optimized drug release mode could lead to a fairly uniform drug concentration distribution along the stent. Therefore, the present study suggested that to achieve a more effective result, optimization of drug eluting strategy (drug release mode) for the DES would be essential. [ABSTRACT FROM AUTHOR]

Renal artery stenosis (RAS) and renal complications emerge in some patients after endovascular aneurysm repair (EVAR) to treat abdominal aorta aneurysm (AAA). The mechanisms for the causes of these problems are not clear. We hypothesized that for EVAR patients, lower limb exercise could negatively influence the physiology of the renal artery and the renal function, by decreasing the blood flow velocity and changing the hemodynamics in the renal arteries. To evaluate this hypothesis, pre- and post-operative models of the abdominal aorta were reconstructed based on CT images. The hemodynamic environment was numerically simulated under rest and lower limb exercise conditions. The results revealed that in the renal arteries, lower limb exercise decreased the wall shear stress (WSS), increased the oscillatory shear index (OSI) and increased the relative residence time (RRT). EVAR further enhanced these effects. Because these parameters are related to artery stenosis and atherosclerosis, this preliminary study concluded that lower limb exercise may increase the potential risk of inducing renal artery stenosis and renal complications for AAA patients. This finding could help elucidate the mechanism of renal artery stenosis and renal complications after EVAR and warn us to reconsider the management and nursing care of AAA patients. [ABSTRACT FROM AUTHOR]

Helical flow in the human aorta is possibly a typical example of 'form follows function' in the vascular system. The helical blood flow may provide guaranties for the inner surface of the ascending aortic wall to get smooth and even washing by the blood so that atherosclerotic plaques can hardly form in the area of the ascending aorta. It has been documented that the phenomenon of helical flow of blood is not just localized in the ascending aorta, it also exists in several large arteries and veins as well. Preliminary studies demonstrated the widely existing helical flow might play positive physiological roles in facilitating blood flow transport, suppressing disturbed blood flow, preventing the accumulation of atherogenic low density lipoproteins on the luminal surfaces of arteries, enhancing oxygen transport from the blood to the arterial wall and reducing the adhesion of blood cells on the arterial surface. These roles of helical blood flow may lessen the burden of arteries and protect the arteries from the pathology of atherosclerosis, thrombosis, and intimal hyperplasia. The great development of time-resolved three-dimensional phase contrast MRI (flow-sensitive 4D-MRI) and the advent of dimensionless indices such as helical flow index proposed to characterize helical flow make clinic quantification of the helical flow in the human large arteries possible. Moreover, researchers probed into the possibility to apply the mechanism of helical flow to the design of vascular interventions to reduce thrombus formation and intimal hyperplasia caused by abnormal flow conditions. [ABSTRACT FROM AUTHOR]

Despite the crucial role of nitric oxide (NO) in the homeostasis of the vasculature, little quantitative information exists concerning NO transport and distribution in medium and large-sized arteries where atherosclerosis and aneurysm occur and hemodynamics is complex. We hypothesized that local hemodynamics in arteries may govern NO transport and affect the distribution of NO in the arteries, hence playing an important role in the localization of vascular diseases. To substantiate this hypothesis, we presented a lumen/wall model of the human aorta based on its MRI images to simulate the production, transport and consumption of NO in the arterial lumen and within the aortic wall. The results demonstrated that the distribution of NO in the aorta was quite uneven with remarkably reduced NO bioavailability in regions of disturbed flow, and local hemodynamics could affect NO distribution mainly via flow dependent NO production rate of endothelium. In addition, erythrocytes in the blood could moderately modulate NO concentration in the aorta, especially at the endothelial surface. However, the reaction of NO within the wall could only slightly affect NO concentration on the luminal surface, but strongly reduce NO concentration within the aortic wall. A strong positive correlation was revealed between wall shear stress and NO concentration, which was affected by local hemodynamics and NO reaction rate. In conclusion, the distribution of NO in the aorta may be determined by local hemodynamics and modulated differently by NO scavengers in the lumen and within the wall. [ABSTRACT FROM AUTHOR]

Evidence from ground-based animal studies using tail-suspended hindlimb unloaded rats model has clearly demonstrated that simulated microgravity-induced smooth muscle cell phenotype conversion, a characteristic vascular structural and functional remodeling, may be one of the key contributors to postspaceflight orthostatic intolerance. However, the rats model involves multiple collective effects of microgravity including cephalic fluid shift and postural muscle unloading on smooth muscle cells (SMCs). It cannot isolate a single factor from the collective ones and therefore is not ideal to study the effects of gravitational vector alteration alone on SMCs. To test the hypothesis that gravitational vector alteration per se might affect smooth muscle cell phenotype, a roller culture apparatus was employed to expose cultured rat aortic smooth muscle cells (RASMCs) to simulated microgravity. Cell proliferation, cell cycle distribution, apoptosis, migration, and nitric oxide production rates were measured and compared between the control and the simulated microgravity groups. Cell cytoskeleton reorganization induced by simulated microgravity was observed by confocal microscopy. Specific contractile and synthetic Gene expression at the mRNA level was quantified by reverse transcriptional polymerase chain reaction. It was observed that simulated microgravity suppressed RASMC proliferation and migration, enhanced cell apoptosis, stimulated NO release, and destroyed the original well-organized cytoskeleton. Moreover, at the mRNA level, long-time exposure (≥72 h) to simulated microgravity induced a contractile phenotype tendency by up-regulating smMHC expression. All these findings suggest that the phenotype modulation of vascular smooth muscle cells may be gravity dependent. [ABSTRACT FROM AUTHOR]

To elucidate the difference between Newtonian and shear thinning non-Newtonian assumptions of blood in the analysis of DES drug delivery, we numerically simulated the local flow pattern and the concentration distribution of the drug at the lumen-tissue interface for a structurally simplified DES deployed in a curved segment of an artery under pulsatile blood flow conditions. The numerical results showed that when compared with the Newtonian model, the Carreau (shear thinning) model could lead to some differences in the luminal surface drug concentration in certain areas along the outer wall of the curved vessel. In most areas of the vessel, however, there were no significant differences between the 2 models. Particularly, no significant difference between the two models was found in terms of the area-averaged luminal surface drug concentration. Therefore, we believe that the shear thinning property of blood may play little roles in DES drug delivery. Nevertheless, before we draw the conclusion that Newtonian assumption of blood can be used to replace its non-Newtonian one for the numerical simulation of drug transport in the DES implanted coronary artery, other more complex mechanical properties of blood such as its thixotropic behavior should be tested. [ABSTRACT FROM AUTHOR]

Blood flow characteristics in an axis-deviated artery bypass model were studied numerically and compared with those in a conventional bypass model. The numerical results revealed that a pronounced swirl flow was created in the host artery by the geometrical configuration of the axis-deviated bypass. The swirl flow created in the axis-deviated bypass model altered the overall flow pattern and eliminated the slow recirculation zone with low wall shear stress existing in the conventional model on the host artery floor where there is disturbed flow known to be associated with the development of intimal thickening and hyperplasia. The numerical study therefore suggests that by intentionally introducing swirl flows into the bypassed arteries, the adverse effects along the host artery floor can be suppressed. [ABSTRACT FROM AUTHOR]

Background: Blood flow condition may have influence upon the hydraulic conductivity of venous graft (Lp,vein) in an arterial bypass, then affecting the accumulation of low-density lipoproteins (LDLs) within the graft wall. To probe this possibility, we first measured in vitro the filtration rates of swine lateral saphenous vein segments under different flow rates, and the correlation of Lp,vein with wall shear stress (WSS) was then obtained.Results: The experimental results showed that when WSS was very low, Lp,vein would increase drastically with WSS from 1.16 ± 0.15 × 10-11 m/s Pa at 0 dyn/cm2 to 2.17 ± 0.20 × 10-11 m/s Pa at 0.7 dyn/cm2, then became constant of approximately 2.33 × 10-11 m/s Pa as the WSS increased further. Based on the experimental results, we assumed three different cases of Lp,vein and numerically simulated the LDLs transport in an arterial bypass model with venous graft. Case A: Lp,vein = 2.33 × 10-11 m/s Pa; Case B: Lp,vein = 1.16 × 10-11 m/s Pa (static condition with WSS of 0); Case C: Lp,vein was shear dependent. The simulation showed that the deposition/accumulation of LDLs within the venous graft wall in Case A was greatly enhanced when compared with that in Case B. However, the LDL accumulation in the graft wall was similar for Case A and Case C.Conclusions: Our study, therefore, indicates that when the venous graft was implanted as a bypass graft, the Lp,vein might remain nearly constant along its whole length except for very few areas where the value of WSS was extremely low (less than 0.7 dyn/cm2) and the effects of Lp,vein modulated by blood flow on LDL transport may be neglected. [ABSTRACT FROM AUTHOR]

Cancer is a malignant tumor that threatens the health of human beings, and has become the leading cause of death in urban and rural residents in China. The glycocalyx is a layer of multifunctional glycans that covers the surfaces of a variety of cells, including vascular endothelial cells, smooth muscle cells, stem cells, epithelial, osteocytes, as well as cancer cells. The glycosylation and syndecan of cancer cell glycocalyx are unique. However, heparan sulfate (HS), hyaluronic acid (HA), and syndecan are all closely associated with the processes of cancer progression, including cell migration and metastasis, tumor cell adhesion, tumorigenesis, and tumor growth. The possible underlying mechanisms may be the interruption of its barrier function, its radical role in growth factor storage, signaling, and mechanotransduction. In the later sections, we discuss glycocalyx targeting therapeutic approaches reported in animal and clinical experiments. The study concludes that cancer cells' glycocalyx and its role in cancer progression are beginning to be known by more groups, and future studies should pay more attention to its mechanotransduction of interstitial flow-induced shear stress, seeking promising therapeutic targets with less toxicity but more specificity. [ABSTRACT FROM AUTHOR]

Background and Aims: The crossed limbs stent graft technique is regularly employed to treat abdominal aortic aneurysm patients with unfavorable aneurysm necks or widely splayed common iliac arteries. This article numerically evaluates the hemodynamic performance of the crossed limbs strategy by analyzing numerical simulations and conducting experiments using two series of idealized bifurcated stent grafts with different cross angles and cross positions.Results: Results demonstrated that the absolute helicity at outlets decreased with increased cross angles and increased with decreased cross positions. The time-averaged wall shear stress remained approximately unchanged, whereas the oscillating shear index and relative resident time decreased slightly when the cross angle increased and cross position decreased in iliac grafts. Additionally, both numerical and in vitro experimental results indicate the displacement force acting on the stent graft gradually increased as cross angles increased and cross positions decreased. Results further indicated that strip areas with a high oscillating shear index and high relative resident time, which may be vulnerable to thrombosis formation, exist along the outer surface of the iliac artery grafts.Conclusion: Given this information, the optimal crossed limbs configuration may contain a small cross angle and low cross position; however, low cross positions may increase the risk of migration. [ABSTRACT FROM AUTHOR]

The vascular smooth muscle cells (VSMCs) are exposed to interstitial flow induced shear stress that may be sensed by the surface glycocalyx, a surface layer composed primarily of proteoglycans and glycoproteins, to mediate cell contraction during the myogenic response. We, therefore, attempted to elucidate the signal pathway of the glycocalyx mechanotransduction in shear stress regulated SMC contraction. Human umbilical vein SMCs (HUVSMCs) deprived of serum for 3-4 days were exposed to a step increase (0 to 20 dyn/cm2) in shear stress in a parallel plate flow chamber, and reduction in the cell area was quantified as contraction. The expressions of Rho kinase (ROCK) and its downstream signal molecules, the myosin-binding subunit of myosin phosphatase (MYPT) and the myosin light chain 2 (MLC2), were evaluated. Results showed that the exposure of HUVSMCs to shear stress for 30 min induced cell contraction significantly, which was accompanied by ROCK1 up-regulation, re-distribution, as well as MYPT1 and MLC activation. However, these shear induced phenomenon could be completely abolished by heparinase III or Y-27632 pre-treatment. These results indicate shear stress induced VSMC contraction was mediated by cell surface glycocalyx via a ROCK-MLC phosphatase (MLCP) pathway, providing evidence of the glycocalyx mechanotransduction in myogenic response. [ABSTRACT FROM AUTHOR]

Background: Abdominal aortic aneurysm (AAA) is a kind of dangerous aortic vascular disease, which is characterized by abdominal aorta partial enlargement. At present, endovascular aneurysm repair (EVAR) is one of the main treatments of abdominal aortic aneurysm. However for some patients after EVAR the aneurysm re-expanded and even ruptured, leading to poor postoperative effect. The stent-graft endoleak after EVAR was realized to influence the AAA in-sac pressure and contribute to the aneurysm re-enlargement.Methods: In order to analyze the influence of endoleaks positions on the pressure shielding ability of stent-graft after EVAR, type I and type III endoleak models were reconstructed based on computed tomography (CT) scan images, and the hemodynamic environment in AAA was numerically simulated.Results: When the endoleak was at the proximal position the pressure shielding ability will be obviously weakened. While, the pressure shielding ability was higher in the systole phase than that in diastole phase when the endoleak located at the middle or distal positions. Unfortunately, when the endoleak located at the proximal position, the pressure shielding ability would be relatively weak in the whole cardiac cycle.Conclusions: The results revealed that the influence of endoleaks on pressure shielding ability of stent-graft was both location and time specific. [ABSTRACT FROM AUTHOR]