Search

To study the influence of multi-factors, such as long sunshine, sand erosion, and so on, in southern Xinjiang, we selected two kinds of composite insulators for the transmission lines in southern Xinjiang to study the aging characteristics of the umbrella skirt surface. The results of scanning electron microscope (SEM) and X-ray photoelectron spectroscopy (XPS) show that the surface roughness of the umbrella skirt is high and there are a large number of micron inorganic particles. The skirt has the characteristics of low C/O element ratio and high Al element content. The results of thermogravimetric analysis and micro infrared test show that the aging depth of the Myli Line skirt after 19 years of operation is 160~190 µm and that of Yuhe Line 1 after 14 years of operation is greater than 180 µm. The plasma discharge method was used to simulate the corona discharge in the actual operation to accelerate the aging of the surface of the umbrella skirt and the hydrophobic recovery of the umbrella skirt was investigated. The results show that the temperature has a great influence on the surface hydrophobic recovery performance after plasma treatment. These results may provide some theoretical guidance and technical support for the selection, operation, and maintenance of composite insulators in Xinjiang.

Abstract In this study, four varieties of rice were cultivated on the same farmland under same conditions and for same duration. However, their lodging resistance was found to be obviously different from each other. Herein, three key factors that highly influenced the lodging resistance were identified. First, in terms of morphological trait, in contrast to the generally believed theory that the overall thickness of the fresh culm wall governs the strength, the thickness of the depressed region of the dried basal culm wall largely determined the mechanical properties by acting as the weak link. This depressed region represents the vulnerable part with high syneresis rate. Second, the culm and its carbon framework exhibited sufficient strength and rigidity for both support and stability of the rice stem. The constraint of high lodging resistance of rice plants is attributed to the culm flexibility. Furthermore, the results of the positron annihilation lifetime spectroscopy corroborate that the most amorphous part and the highest-fraction free volume in the culm carbon framework were found for samples that exhibited high lodging resistance. This result confirmed the significant influence of the culm flexibility on lodging resistance. Third, a higher level of nitrogen element content in the basal culm can benefit its growth and development, which may contribute to an increase in lodging resistance of rice plants.

In the long-term working state, stains such as dust, oil, and charged particles in the environment are prone to deposit on the surface of the power equipment, which has great security risks. To achieve anti-stain performance, fluorocarbon composite coating with a low surface energy was prepared and studied. In this paper, SiO2 nanoparticles were used as inorganic fillers and fluorocarbon resin was used as the substrate to form anti-stain coatings. By adjusting and optimizing the ratio of fillers and organic resins, coatings with different static contact angles were constructed. The optimum composite coating has a contact angle of 151 ± 2° and a surface energy of 9.6 mJ/m2. After high-temperature treatment (up to 200 °C), immersion in corrosive solutions (pH 3–11), and sandpaper abrasion (after 5 abrasion cycles), the coating has been proven to show good thermal, chemical and mechanical stability. Our study provides significant research and market opportunities for the anti-stain application of the fluorocarbon composite coating on power equipment.

In this study, the aging process of a surface-functional titanium dioxide nanosheet (f-TNS) composited room-temperature-vulcanized silicone rubber (RTV) composite coating was simulated in a NO2 generation device, and then the electrochemical impedance spectroscopy (EIS) of the aged composite coating was tested in a 3.5% NaCl solution. The water permeation process was analyzed by the changes in the impedance modulus, porosity, and breakpoint frequency of the composite coating. The experimental results show that the water permeability of aged RTV decreases first and then increases with the increase in the composite proportion of f-TNS. When the composite proportion of TNS was 0.3 wt.%, the composite sample had the minimum water permeability and the best resistance to NO2 corrosion. The effect of TNS on the NO2 aging resistance of RTV composites and its mechanism were studied by SEM, FT-IR, and XPS. The impedance modulus and porosity of the aged 0.3% f-TNS/RTV, respectively, were 1.82 × 107 Ω cm2 and 0.91 × 10−4%, which increased by 2.23 times and decreased by 0.37 times, respectively, compared with the values of aged pure RTV sample. In addition, the breakpoint frequency of the aged 0.3% f-TNS/RTV also significantly reduced to 11.3 Hz, whereas it was 35 Hz in aged pure RTV.

In a high-moisture environment where dust and coastal saltwater are prevalent, the stability of power equipment can be adversely affected. This issue can result in equipment downtime, particularly for transformers, severely disrupting the continuous operation of DC transmission systems. To address this challenge, a superhydrophobic modified fluorosilicone coating was developed, incorporating anti-stain properties. To tackle this issue comprehensively, an orthogonal experiment was conducted, involving six factors and three levels. The study focused particularly on assessing the impact of water-repellent recovery agents, nanofillers, antistatic agents, anti-mold agents, leveling agents, as well as wetting and dispersing agents on the coating’s surface tension. The results demonstrate that selecting an appropriate base resin and incorporating well-matched functional additives played a central role in effectively reducing the surface tension of the coating. Consequently, optimized coatings exhibited exceptional resistance to stains and displayed strong corrosion resistance.

The development of photocatalysts with a wide spectral response and effective carrier separation capability is essential for the green degradation of tetracycline hydrochloride. In this study, a magnetic recyclable Z-scheme ZnO/ZnFe2O4 heterojunction (ZZF) was successfully constructed via the solid phase method, using MIL-88A(Fe)@Zn as the precursor. An appropriate band gap width and Z-scheme charge transfer mechanism provide ZZF with excellent visible light absorption performance, efficient charge separation, and a strong redox ability. Under visible light irradiation, the degradation efficiency of tetracycline hydrochloride for the optimal sample can reach 86.3% within 75 min in deionized water and 92.9% within 60 min in tap water, exhibiting superior stability and reusability after five cycles. Moreover, the catalyst in the water can be conveniently recovered by magnetic force. After visible light irradiation for 70 min, the temperature of the reaction system increased by 21.9 °C. Its degradation constant (35.53 × 10−3 min−1) increased to 5.1 times that at room temperature (6.95 × 10−3 min−1). Using thermal energy enhances the kinetic driving force of the reactants and facilitates carrier migration, meaning that more charge is available for the production of •O2− and •OH. This study provides a potential candidate for the efficient degradation of tetracycline hydrochloride by combining thermal catalysis with a photocatalytic heterojunction.

In this study, functional graphene oxide (f-GO) nanosheets were prepared to enhance the NO2 resistibility of room-temperature-vulcanized (RTV) silicone rubber. A nitrogen dioxide (NO2) accelerated aging experiment was designed to simulate the aging process of nitrogen oxide produced by corona discharge on a silicone rubber composite coating, and then electrochemical impedance spectroscopy (EIS) was used to test the process of conductive medium penetration into silicone rubber. After exposure to the same concentration (115 mg·L−1) of NO2 for 24 h, at an optimal filler content of 0.3 wt.%, the impedance modulus of the composite silicone rubber sample was 1.8 × 107 Ω·cm2, which is an order of magnitude higher than that of pure RTV. In addition, with an increase in filler content, the porosity of the coating decreases. When the content of the nanosheet increases to 0.3 wt.%; the porosity reaches a minimum value 0.97 × 10−4%, which is 1/4 of the porosity of the pure RTV coating, indicating that this composite silicone rubber sample has the best resistance to NO2 aging.

Uniform polyaniline (PANI) nanotubes were synthesized by a self-assembly method under relatively dilute hydrochloric acid (HCl) solution. Scanning electron microscopy (SEM), Fourier transform infrared (FTIR) spectroscopy, and UV-Vis-NIR spectroscopy were employed to characterize the morphology and molecular structure of the PANI products. SEM images show that the PANI nanotubes have uniform morphology and form compact coating on the substrate surface. For comparison, aggregated PANI was also synthesized by conventional polymerization method. The performance of the PANI products on carbon steel was studied using eletrochemical measurement and immersion corrosion experiment in 3.5 wt% NaCl aqueous solution. The corrosion potentials of carbon steel samples increase by 0.196 V and 0.060 V after coated with PANI nanotubes and aggregated PANI, respectively, and the corrosion currents density decrease by about 76.32% and 36.64%, respectively. The 6-day immersion experiment showed that the carbon steel samples coated by PANI nanotubes showed more excellent anticorrosion performance, because the more compact coating formed by PANI nanotubes may inhibit the corrosion process between the anodic and cathodic.

In this paper, gas chromatography–mass spectrometry (GC–MS) and positron annihilation lifetime spectroscopy (PALS) were used to probe the changes of oligomers and the polydimethylsiloxane (PDMS) network in silicone rubber, after different durations of UVA/UVB irradiation. At the early stage (4-D9 decreases. The o-Ps intensity of the extracted silicone rubber increases in the stage after UVB irradiation. These results indicate the crosslinking of oligomers into the PDMS network. After a long duration (>300 h) of UVB irradiation, D4 was generated and the lifetime of τ3 also increased, indicating the rupture of the Si-O bond in the PDMS network. These two aging processes were termed the post curing process and the chain session process. The new finding was that UVA could only induce the post curing process; UVB causes the rupture of the chemical bond in silicone rubber. Photons of UVB could break the C-H bond, and then trigger the backbiting decomposition of PDMS, breaking the Si-O bond, while the photons of UVA cannot. The fact that D4 was generated after UVB irradiation can be used to evaluate the UVB stability of silicone rubber in the future.

Tunable mesoporous silica films were prepared though a sol-gel process directed by the self-assembly of various triblock copolymers. Positron annihilation γ-ray energy spectroscopy and positron annihilation lifetime spectroscopy (PALS) based on intense pulsed slow positron beams as well as ellipsometric porosimetry (EP) combined with heptane adsorption were utilized to characterize the open porosity/interconnectivity and pore size distribution for the prepared films. The consistency between the open porosities was examined by the variations of orthopositronium (o-Ps) 3γ annihilation fractions and the total adsorbed volumes of heptane. The average pore sizes deduced by PALS from the longest-lived o-Ps lifetimes are in good agreement with those by EP on the basis of the Barrett–Joyner–Halenda model, as indicated by a well fitted line of slope k = 1. The results indicate that the EP combined with heptane adsorption is a useful method with high sensitivity for calibrating the mesopore size in highly interconnected mesoporous films, whereas PALS is a novel, complementary tool for characterizing both closed and open pores in them.

Surface hydrophobicity/hydrophilicity of titania (TiO _2 ) films, spin-coated on silicon wafers, were tuned by introducing surface mesopores with various morphologies using a triblock copolymer F38 as the template agent of different weight ratios via a sol-gel method. It is found that both the porosity (2.92 ∼ 33.03%) and the surface roughness (0.22 ∼ 0.43 nm for arithmetic mean roughness and 0.28 ∼ 0.58 nm for root mean square roughness) of the films increase monotonically as increasing F38 ratio from 5 to 25 wt%, accompanied by distinct changes of pore morphology from isolated mesopores with pore sizes of 5 ∼ 7 nm to longer worm-like pores (30 ∼ 100 nm in length). The apparent static contact angle ( θ *) of the films with isolated mesopores is enhanced from ca. 90.6° to 100.1° as indicated by an increase of the roughness factor with incresing F38 from 5 to 15 wt%, which is in qualitative agreement with the Wenzel’s equation. Interestingly, the films with interconnected worm-like pores show obvious hydrophilicity ( θ * = 80.7°) with further increasing F38 ratio higher than 20 wt%. The reversed surface wettability show that not only surface roughness but also pore morphology could significantly affect the wettability of the mesoporous TiO _2 films.